LTR50UZPD1601 [ROHM]
Fixed Resistor, Metal Glaze/thick Film, 1W, 1600ohm, 200V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP;型号: | LTR50UZPD1601 |
厂家: | ROHM |
描述: | Fixed Resistor, Metal Glaze/thick Film, 1W, 1600ohm, 200V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP 电阻器 |
文件: | 总4页 (文件大小:174K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Power Chip Resistors
<Wide Terminal type>
LTR50 (5025 size : 1W)
z Features
1) Improved welding strength
The structure of longer electrodes provides the wider welding area than the chip resistors with normal electrodes, and this
enhanced the solder welding strength.
2) Increased surge-resistance
This is achieved by Rohm’s original trimming technology plus resistive element patterning.
3) High-power tolerance
Two times of the rated power is guaranteed than the normal-electrode resistors.
4) ROHM resistors are ISO-9001 & ISO/TS16949 certified.
zApplications
Automotive, industrial and power supply.
zRatings
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering
it.
Item
Conditions
Specifications
1W
Rated power
Power must be derated according to the power derating curve in
at 70°C
Figure 1 when ambient temperature exceeds 70°C.
100
80
60
40
20
0
−55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
P: Rated power (W)
E= P×R
R: Nominal resistance (Ω)
Limiting element voltage
200V
Nominal resistance
See Table 1.
Operating temperature
−55°C to + 155°C
D( 0.5%) F( 1%) J( 5%)
Table 1
Resistance range
Resistance temperature coefficient
Resistance tolerance
(Ω)
(ppm/°C)
D
F
J
( 0.5%)
( 1%)
100
100
200
10 to 130k (E24)
1 to 1M (E24)
( 5%)
www.rohm.com
2009.05 - Rev.C
1/3
c
○ 2009 ROHM Co., Ltd. All rights reserved.
LTR50
Data Sheet
zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level
loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component
cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
zCharacteristics
Guaranteed value
Item
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistor type
J : 5%
F : 1%
D : 0.5%
Resistance
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum overload voltage : 200V
Overload
(2.0%+0.1Ω)
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
Rapid change of
temperature
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
Damp heat, steady state
(3.0%+0.1Ω)
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
JIS C 5201-1 4.25.3
155°C
Endurance
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
(1.0%+0.05Ω)
Without mechanical damage such as breaks.
JIS C 5201-1 4.33
Bend strength of
the end face plating
EIAJ ED-4701/300 Test method 304
Voltage : 3kv
C : 100pF
R : 1.5kΩ
Apply cycle : 1 time
Static electric
characteristics
(5.0%+0.05Ω)
www.rohm.com
2009.05 - Rev.C
2/3
c
○ 2009 ROHM Co., Ltd. All rights reserved.
LTR50
Data Sheet
zDimensions (Unit : mm)
①
⑥
0.38±0.2
②
③
No.
1
Material
Resistive element
(Oxide metal thick film)
0.90±0.2
④
2.50±0.15
⑤
2
3
4
5
6
Silver thick film electrode
Nickel electrode
Sn electrode
Alumina substrate
Overcoating (Resin)
5.0±0.15
zPackaging
Reel
Taping
P
0
P2
D
φ
A
B
D
K
A
0
P1
C
(Unit : mm)
Label
W
F
E
A
0
B0
EIAJ ET-7200B compliant
12.0 0.3
5.5 0.05
1.75 0.1
3.4 0.2
5.6 0.2
K
(Unit : mm)
D
A
B
C
D0
P0
P
1
P2
0
−1.5
+1
0
+1.0
0
+0.1
0
φ180
φ13 0.2
φ60
4.0 0.1
4.0 0.1
2.0 0.05
Max. 1.1
13
φ1.5
zPart designation
L T R 5 0 U Z P J
Resistance tolerance
Nominal resistance
Resistance code, 3 or 4 digits.
Part No.
D
F
J
0.5%
1%
Resistance
tolerance
Resistance
code
5%
F , D
J
:
:
4 digits
3 digits
Packaging Specifications Code
Resistance tolerance
D( 0.5%) F( 1%) J( 5%)
Basic ordering unit
(pcs)
Part No.
Code
Packaging specifications
Reel
φ180mm (7inch)
LTR50
UZP
Embossed tape (4mm Pitch)
5,000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
www.rohm.com
2009.05 - Rev.C
3/3
c
○ 2009 ROHM Co., Ltd. All rights reserved.
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039
A
相关型号:
LTR50UZPD1603
Fixed Resistor, Metal Glaze/thick Film, 1W, 160000ohm, 200V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP
ROHM
LTR50UZPD1653
Fixed Resistor, 1W, 165000ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD1671
Fixed Resistor, 1W, 1670ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD16R4
Fixed Resistor, 1W, 16.4ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD16R5
Fixed Resistor, 1W, 16.5ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD16R7
Fixed Resistor, 1W, 16.7ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD1762
Fixed Resistor, 1W, 17600ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD1800
Fixed Resistor, Metal Glaze/thick Film, 1W, 180ohm, 200V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP
ROHM
LTR50UZPD1823
Fixed Resistor, 1W, 182000ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD1840
Fixed Resistor, 1W, 184ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD1893
Fixed Resistor, 1W, 189000ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP, ROHS COMPLIANT
ROHM
LTR50UZPD2003
Fixed Resistor, Metal Glaze/thick Film, 1W, 200000ohm, 200V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 1020, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明