MCR004QLPJ [ROHM]

ROHM的贴片电阻器是采用了金属釉阻体的高可靠性贴片电阻器。被应用于从消费电子设备到车载、工业设备等各种用途，备有以适用于移动通信设备、便携小型设备的超小型贴片电阻器为代表的众多产品。;


型号：	MCR004QLPJ
厂家：	ROHM
描述：	ROHM的贴片电阻器是采用了金属釉阻体的高可靠性贴片电阻器。被应用于从消费电子设备到车载、工业设备等各种用途，备有以适用于移动通信设备、便携小型设备的超小型贴片电阻器为代表的众多产品。电子通信通信设备固定电阻器
文件：	总6页 (文件大小：96K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MCR01

Resistors

Thick film rectangular

MCR01 (1005 size : 1 / 16W)

zFeatures

1) Extremely small light

Area ratio is 60% smaller than that of chip 1608, while weight ratio has been cut 75%.

2) Highly reliable chip resistor

Ruthenium oxide dielectric offers superior resistance to the elements.

3) Electrodes not corroded by soldering

Thick film makes the electrodes very strong.

4) Flat surface further facilitates mounting

Mounting can also be automated.

5) ROHM resistors have approved ISO–9001 certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the

product before using or ordering it.

zRatings

Item

Rated power

Conditions

Specifications

0.063W (1 / 16W)

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

at 70°C

100

−55

100 125

155

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

R: Nominal resistance (Ω)

E= P×R

Limiting element voltage

50V

Nominal resistance

See Table 1.

−55°C to +155°C

Operating temperature

Rev.A

1/5

MCR01

Resistors

Jumper type

Table 1

Resistance

Max. 50mΩ

Resistance range

Resistance temperature coefficient

Resistance tolerance

(Ω)

(ppm / °C)

+500 / −250

200

Rated current

1.0≤R<10

(E24)

Operating temperature

−55°C to +155°C

J ( 5%)

10≤R≤10M (E24)

F ( 1%)

D ( 0.5%)

10≤R≤2.2M (E24)

10≤R<100 (E24)

100

100≤R≤1MΩ (E24)

zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to

evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with

a steady state voltage that is greater than its rated voltage.

Characteristics

Guaranteed value

Resistor type Jumper type

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

J : 5% Max. 50mΩ

F : 1%

D : 0.5%

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 100V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Rev.A

2/5

MCR01

Resistors

zExternal dimensions (Unit : mm)

0.2 0.1

No.

Material

+0.05

0.25

Thick dielectric glaze of oxide metal (only silver used for jumper)

Thick film of silver for electrode

Nickel-coated electrode

−0.1

1.0 0.05

External electrode coated with Sn

Alumina substrate

Overcoating

Packaging

Reel

Taping

φD0

Heat crimp cover/Tape

Thick paper (Underside paper tape) Chip resistor Square punchout hole

mount

(Unit : mm)

Label

EIAJ ET-7200B compliant

8.0 0.3

3.5 0.05

1.75 0.1

0.7 0.1

1.2 0.1

(Unit : mm)

+0.1

4.0 0.1

2.0 0.05

Max. 1.1

φ1.5

−1.5

+1.0

φ180

φ13 0.2

φ60

Rev.A

3/5

MCR01

Resistors

zPart designation

3-digit or 4-digit IEC coding system

Part No.

Nominal resistance

Resistance tolerance

Packaging specifications code

Part No. Code Packaging style

Basisic ordering

unit (pcs)

0.5%

Specify "J" for jumper also.

MCR01 MZP

Paper tape

10 000

zDimensions

1.20

1.15

1.10

1.05

1.00

0.95

0.90

0.85

0.80

0.70

0.65

0.60

0.55

0.50

0.45

0.40

0.35

0.30

0.55

0.50

0.45

0.40

0.35

0.30

0.25

0.20

0.15

JIS C 5201-1 4.4.2

SAMPLE SIZE : n=20pcs

MICROMETER

JIS C 5201-1 4.4.2

SAMPLE SIZE : n=20pcs

MICROMETER

JIS C 5201-1 4.4.2

SAMPLE SIZE : n=20pcs

MICROMETER

100

10k 100k

100

10k 100k

100

10k 100k

RESISTANCE (Ω)

Fig.2 Dimensions (length)

Fig.3 Dimensions (width)

Fig.4 Dimensions (thickness)

Electrical characteristics

8.0

4.0

3.0

800

JIS C 5201-1 4.13

JIS C 5201-1 4.8

SAMPLE SIZE : n=10pcs

25°C / 125°C

JIS C 5201-1 4.5

SAMPLE SIZE : n=20pcs

20°C 65%RH

SAMPLE SIZE : n=10pcs

RATED VOLTAGE × 2.5TIMES : 2s

LIMITING ELEMENT VOLTAGE : 100V

6.0

4.0

600

400

2.0

1.0

200

0.0

– 2.0

– 4.0

– 6.0

– 8.0

−1.0

−2.0

−3.0

−4.0

−200

−400

−600

−800

100

10k 100k

100

10k 100k

100

10k 100k

RESISTANCE (Ω)

Fig.5 Resistance

Fig.6 Variation of resistance with

temperature

Fig.7 Overload

Rev.A

4/5

MCR01

Resistors

2.0

1.5

2.0

1.5

4.0

3.0

JIS C 5201-1 4.18

JIS C 5201-1 4.19

SAMPLE SIZE : n=10pcs

−55°C / 125°C 5cyc

JIS C 5201-1 4.24

SAMPLE SIZE : n=10pcs

SOLDERING CONDITION

: 260°C 10s

SAMPLE SIZE : n=10pcs

40°C 93%RH WITH NO LOAD

1000h

1.0

2.0

0.5

1.0

0.0

−0.5

−1.0

−1.5

−2.0

−0.5

−1.0

−1.5

−2.0

−1.0

−2.0

−3.0

−4.0

100

10k 100k

100

10k 100k

100

10k 100k

RESISTANCE (Ω)

Fig.8 Resistance to soldering heat

Fig.9 Rapid change of

temperature

Fig.10 Damp heat, steady state

4.0

3.0

2.0

1.5

JIS C 5201-1 4.25.1

SAMPLE SIZE : n=10pcs

70°C 1,000h

JIS C 5201-1 4.25.3

SAMPLE SIZE : n=10pcs

125°C WITH NO LOAD 1,000h

JIS C 5201-1 4.29

SAMPLE SIZE : n=10pcs

IPA, 5min.

3.0

2.0

OVERLOAD : THE RATED VOLTAGE

2.0

1.0

0.5

0.0

−1.0

−2.0

−3.0

−4.0

−1.0

−2.0

−3.0

−4.0

−0.5

−1.0

−1.5

−2.0

100

10k 100k

100

10k 100k

100

10k 100k

RESISTANCE (Ω)

Fig.11 Endurance at 70°C

Fig.12 Endurance

Fig.13 Resistance to solvents

2.0

1.5

JIS C 5201-1 4.33

SAMPLE SIZE : n=10pcs

ENDURANCE WITH 90mm WIDTH

1.0

0.5

0.0

−0.5

−1.0

−1.5

−2.0

100

10k 100k

RESISTANCE (Ω)

Fig.14 Bend strength of

the end face plating

Rev.A

5/5

Appendix

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level of

reliability and the malfunction of with would directly endanger human life (such as medical instruments,

transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other

safety devices), please be sure to consult with our sales representative in advance.

About Export Control Order in Japan

Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control

Order in Japan.

In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)

on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.

Appendix1-Rev1.1

MCR004QLPJ [ROHM]

相关型号：

MCR004QLPJ000

MCR004RZP

MCR004RZPD100

MCR004RZPF

MCR004RZPF100

MCR004RZPF15R0

MCR004RZPF16R0

MCR004RZPF1803

MCR004RZPF5102

MCR004RZPF5603

MCR004RZPFF

MCR004RZPFJ