MCR004RZPJJ [ROHM]
Compact Film Chip Resistors; 紧凑型片式电阻器型号: | MCR004RZPJJ |
厂家: | ROHM |
描述: | Compact Film Chip Resistors |
文件: | 总5页 (文件大小:149K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Compact Film Chip Resistors
MCR004 (01005 size : 1 / 32W)
Features
1) Extremely small
Area ratio is 50% smaller than that of chip 0201.
2) High dimensional precision
Novel semiconductor process technology guarantees an external dimensional tolerance of 20µm.
3) Pressed carrier tape applications
Using a pressed carrier tape reduces mounting errors compared with conventional carrier tapes.
4) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the
product before using or ordering it.
Ratings
Item
Conditions
Specifications
0.031W (1 / 32W)
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
Rated power
at 70°C
100
80
60
40
20
0
−55
0
70
100 125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
P: Rated power (W)
R: Nominal resistance (Ω)
E= P×R
Limiting element voltage
15V
Nominal resistance
See Table 1.
−55°C to +125°C
Operating temperature
Table 1
Resistance range
Resistance temperature coefficient
Resistance tolerance
(Ω)
(ppm / °C)
Jumper type
Resistance
300
250
300
250
J ( 5%)
Max. 50mΩ
Rated current
0.5A
F ( 1%)
Operating temperature
−55°C to +125°C
Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level
loads), be certain to valuate the component in the mounted state. In addition, the reliability and performance of this component
cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
www.rohm.com
2011.06 - Rev.D
1/4
c
○ 2011 ROHM Co., Ltd. All rights reserved.
MCR004
Data Sheet
Characteristics
Guaranteed value
Resistor type Jumper type
Item
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistance
J : 5% Max. 50mΩ
F : 1%
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : +20 / −55 / +20 / +125°C
See Table.1
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage ×2 : 30V
Overload
(2.0%+0.1Ω)
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
Max. 50mΩ
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 100cyc
Rapid change of
temperature
Max. 100mΩ
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
Damp heat, steady state
(3.0%+0.1Ω)
Max. 100mΩ
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
3°C
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
(1.0%+0.05Ω)
Max. 100mΩ
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.25.3
125°C
Endurance
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
JIS C 5201-1 4.33
Bend strength of
the end face plating
Without mechanical damage such as breaks.
Dimensions (Unit : mm)
L
a
Size code
L
W
t
a
b
Part No.
MCR004
mm (inch)
W
0402(01005)
0.4 0.02
0.2 0.02
0.13 0.02
0.1 0.03
0.1 0.03
t
b
www.rohm.com
2011.06 - Rev.D
2/4
c
○ 2011 ROHM Co., Ltd. All rights reserved.
MCR004
Data Sheet
・
Packaging
Paper tape(2mm Pitch)
Reel
Taping
P0
P
2
φD0
E
F
A
0
W
B0
A
B
D
P
1
Heat crimp cover Tape
Thick paper
Square press hole
Chip resistor
T
2
C
Label
Press career tape
E
(Unit : mm)
EIAJ ET-7200B compliant
W
F
A
0
B0
(Unit : mm)
D
8.0 0.2
3.5 0.05
1.75 0.1
0.24 0.03 0.45 0.03
A
B
C
D0
P0
P1
P2
T2
0
−15
+1.0
0
+1
0
+0.1
0
φ180
9
φ13 0.2
φ60
4.0 0.1
2.0 0.05
2.0 0.05
Max. 0.50
φ1.5
・
Embossed tape(1mm Pitch)
Reel
Taping
P0
P
2
φD0
E
F
A
0
W
B0
A
B
D
P
1
Top tape
Pocket
Components
Base Embossed
T
2
C
(Unit : mm)
Label
W
F
E
0.9 0.05
A
0
B0
4.0 0.05
1.8 0.02
0.23 0.02 0.43 0.02
(Unit : mm)
D
D0
P0
P1
P2
T2
A
B
C
0.8 0.04
2.0 0.04
1.0 0.02
1.0 0.02
0.2 0.02
+1.0
-0.6
φ178 1.0
φ60 1.0
5
φ13 0.2
www.rohm.com
2011.06 - Rev.D
3/4
c
○ 2011 ROHM Co., Ltd. All rights reserved.
MCR004
Data Sheet
Part No. Explanation
M C R 0 0 4 Y Z P J
Part No.
Resistance tolerance Nominal resistance
F
1%
Resistance code, 3 or 4 digits.
000 denotes jumper type.
J
5%
Resistance
tolerance
Resistance
code
J is also used
for jumper
F
J
:
:
4 digits
3 digits
Packaging Specifications Code
Resistance tolerance
J( 5%) F( 1%)
Part No.
Code
Packaging specifications
Reel
Basic ordering unit (pcs)
,
15 000
,
40 000
YZP
RZP
Paper tape (2mm Pitch)
Embossed tape (1mm Pitch)
φ180mm
φ180mm
MCR004
Reel (φ180) : JEITA ET-7200B
: Standard product
www.rohm.com
2011.06 - Rev.D
4/4
c
○ 2011 ROHM Co., Ltd. All rights reserved.
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
R1120
A
相关型号:
©2020 ICPDF网 联系我们和版权申明