MCR03EZPD2401 [ROHM]
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 2400ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP;型号: | MCR03EZPD2401 |
厂家: | ROHM |
描述: | Fixed Resistor, Metal Glaze/thick Film, 0.1W, 2400ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP 电阻器 |
文件: | 总5页 (文件大小:70K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MCR03
Resistors
Compact Thick Film Chip Resistors
MCR03 (0603 size)
zFeatures
1) Power rating of 1 / 10W
2) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Resin protective coating absorbs impact, facilitates mounting.
5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
zRatings
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the
product before using or ordering it.
Item
Rated power
Conditions
Specifications
0.10W (1 / 10W)
at 70°
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
C
100
80
60
40
20
0
−55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V) P: Rated power (W)
R: Nominal resistance (Ω)
E= P×R
Limiting element voltage
50V
Nominal resistance
See Table 1.
Operating temperature
−55°C to +155°C
Rev.K
1/4
MCR03
Resistors
Table 1
Jumper type
Resistance range
Resistance temperature coefficient
Resistance
Max. 50mΩ
1A
Resistance tolerance
(Ω)
(ppm/°C)
Rated current
1.0 to 9.1
10 to 10M
10 to 10M
(E24)
400
J ( 5%)
Operating temperature
−55°C to +155°C
(E24)
200
100
FX ( 1%)
(E24,96)
10 to 91
(E24)
(E24)
100
50
D ( 0.5%)
100 to 1M
zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
z
Characteristics
Guaranteed value
Resistor type Jumper type
J : 5%
FX : 1%
D: 0.5%
Item
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Max. 50mΩ
Resistance
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum overload voltage : 100V
Overload
(2.0%+0.1Ω)
Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
Max. 50mΩ
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
Rapid change of
temperature
Max. 100mΩ
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
Damp heat, steady state
Endurance at 70°C
Endurance
(3.0%+0.1Ω)
(3.0%+0.1Ω)
Max. 100mΩ
Max. 100mΩ
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
155°C
Test time : 1,000h to 1,048h
(1.0%+0.05Ω)
(1.0%+0.05Ω)
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
JIS C 5201-1 4.33
Bend strength of
the end face plating
Without mechanical damage such as breaks.
Rev.K
2/4
MCR03
Resistors
zDimensions (Unit : mm)
1
No.
Material
2
3
0.3 0.2
1
Resistive element (Oxide metal thick film)
2
3
4
5
6
Silver thick film electrode
Nickel electrode
0.3 0.2
Sn electrode
1.6 0.1
4
Alumina substrate
Overcoating (Resin)
5
z
Packaging
Reel
Taping
P
0
P
2
P1
φD0
E
F
W
B
0
A0
A
B
D
Heat crimp cover Tape
Thick paper
mount
Chip resistor Square punchout hole
(Underside paper tape)
T
2
(Unit : mm)
W
F
E
A
0
B0
8.0 0.3
3.5 0.05
1.75 0.1
1.1 0.1
1.9 0.1
C
D0
P
0
P
1
P
2
T2
Label
+0.1
0
EIAJ ET-7200B compliant
4.0 0.1
4.0 0.1
2.0 0.05
Max. 1.1
φ1.5
(Unit : mm)
D
Narrow pitch (2mm pitch) version
A
B
C
P0
P
2
P1
0
−3
+1.0
0
+1
0
φD0
φ180
9
φ13 0.2
φ60
E
F
W
B
0
Bulk case
A0
Heat crimp cover Tape
(Underside paper tape)
Thick paper
mount
Chip resistor Square punchout hole
Slider
T
2
Shutter
12 0.1
(Unit : mm)
0
36
W
F
E
A
0
B0
−0.2
8.0 0.3
3.5 0.05
1.75 0.1
1.1 0.1
1.9 0.1
D0
P
0
P
1
P
2
T2
+0.1
0
4.0 0.1
2.0 0.05
2.0 0.05
Max. 1.1
φ1.5
110 0.7
EIAJ ET-7200B compliamt
(Unit : mm)
Rev.K
3/4
MCR03
Resistors
zPart No. Explanation
M C R 0 3 E Z P
J
Part No.
Resistance tolerance Nominal resistance
D
F
J
0.5%
Resistance code, 3 or 4 digits.
000 denotes jumper type.
1%
Resistance
tolerance
Resistance
code
5%
J is also used
for jumper
F, D
J
:
:
4 digits
3 digits
Packaging Specifications Code
Resistance tolerance
J( 5%) F( 1%) D( 0.5%)
Part No.
Code
Packaging specifications
Reel
Basic ordering unit (pcs)
Remarks
−
Paper tape (4mm Pitch)
Paper tape (2mm Pitch)
Bulkcase
,
MCR03
MCR03
MCR03
EZP
MZP
PZPI
φ180mm (7inch)
φ180mm (7inch)
5 000
−
−
10,000
25,000
Narrow pitch type
−
−
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
Rev.K
4/4
Appendix
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
CO.,LTD.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account when
designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no respon-
sibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples of
application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or
exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility
whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment or
devices (such as audio visual equipment, office-automation equipment, communication devices, electronic
appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no
responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended
to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
THE AMERICAS / EUROPE / ASIA / JAPAN
ROHM Customer Support System
Contact us : webmaster@ rohm.co.jp
www.rohm.com
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Copyright © 2008 ROHM CO.,LTD.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
Appendix1-Rev3.0
相关型号:
MCR03EZPD242
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 2400ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD243
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 24000ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD271
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 270ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD273
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 27000ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD27R0
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 27ohm, 50V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD300
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 30ohm, 50V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD3001
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 3000ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD303
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 30000ohm, 50V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD30R1
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 30.1ohm, 50V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD30R9
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 30.9ohm, 50V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD33R0
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 33ohm, 50V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP
ROHM
MCR03EZPD33R2
Fixed Resistor, Metal Glaze/thick Film, 0.1W, 33.2ohm, 50V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明