MCR100JZHJLR91 [ROHM]
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.91ohm, 3.01V, 5% +/-Tol, 250ppm/Cel, Surface Mount, 2512, CHIP;型号: | MCR100JZHJLR91 |
厂家: | ROHM |
描述: | Fixed Resistor, Metal Glaze/thick Film, 1W, 0.91ohm, 3.01V, 5% +/-Tol, 250ppm/Cel, Surface Mount, 2512, CHIP 电阻器 |
文件: | 总10页 (文件大小:1027K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Low ohmic thick film chip resistors
MCR series - lowohmic -
Datasheet
●
Features
1)Very-low ohmic resistance from 47mΩ is in lineup by thick-film resistive element.
2)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.
Size
Automotive
grade
Packaging
Part No.
Type code
Quantity/ Reel
specifications
(mm)
0603
1005
1608
2012
3216
3225
5025
6432
(inch)
0201
0402
0603
0805
1206
1210
2010
2512
available
MCR006
MCR01
MCR03
MCR10
MCR18
MCR25
MCR50
MCR100
YLP
MZP
EZP
EZH
EZH
JZH
JZH
JZH
Paper tape(2mmpitch)
Paper tape(2mmpitch)
Paper tape(4mmpitch)
Paper tape(4mmpitch)
Paper tape(4mmpitch)
Embossed tape(4mmpitch)
Embossed tape(4mmpitch)
Embossed tape(4mmpitch)
15,000
10,000
5,000
5,000
5,000
4,000
4,000
4,000
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
●Part number description
M C R
1 0
E Z H
J
L
1 R 0
Resistance
tolerance
Part No.
Size (mm [inch])
Type code
Special part code
Nominal resistance
Resistance code,3 or 4 digits.
Resistance
006(0603[0201])
01(1005[0402])
03(1608[0603])
10(2012[0805])
18(3216[1206])
25(3225[1210])
50(5025[2010])
100(6432[2512])
F(±1%)
J(±5%)
0.1~ 9.1Ω(±1%)
L
MCR
0.1~ 0.9Ω(±5%)
(Micro chip
resistors)
tolerance
+
Resistance
code
S
0.047~ 0.091Ω
Special P / N
FL, FS, JS
JL
4 digits
3 digits
:
:
EX.)
0.047Ω=R047 ( ±1%, ±5%)
9.1Ω=9R10 ( ±1%)
9R1 ( ±5%)
www.rohm.com
©2016 ROHMCo., Ltd.All rights reserved.
1/6
2017.01 - Rev.G
MCR series - lowohmic -
Datasheet
●Products list
Rated
Limiting
element
voltage
(V)
Operating
temperature
range
Temperature Resistance
power
(70℃)
(W)
Resistance range
(Ω)
Type
code
Part No.
coefficient
tolerance
(ppm / ℃)
(%)
(℃)
MCR006
MCR01
MCR03
YLP
MZP
EZP
0.05
0.063
0.1
0.67
0.76
0.95
+600/-200 F( ±1%)
1.0≦R≦9.1
(E24 series)
(E24 series)
(E24 series)
-55 ~ +125
-55 ~ +155
-55 ~ +155
±400
±400
F( ±1%)
F( ±1%)
1.0≦R≦9.1
1.0≦R≦9.1
500±300
400±200
±250
500±300
400±200
±250
500±300
400±200
±250
500±300
400±200
±250
300±300
±200
300±300
±200
500±300
400±200
±250
500±300
400±200
±250
J ( ±5%)
J ( ±5%)
J ( ±5%)
F( ±1%)
F( ±1%)
F( ±1%)
J ( ±5%)
J ( ±5%)
J ( ±5%)
F( ±1%)
F( ±1%)
F( ±1%)
J ( ±5%)
J ( ±5%)
F( ±1%)
F( ±1%)
J ( ±5%)
J ( ±5%)
J ( ±5%)
F( ±1%)
F( ±1%)
F( ±1%)
J ( ±5%)
J ( ±5%)
J ( ±5%)
F( ±1%)
F( ±1%)
F( ±1%)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦0.91 (E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦9.1 (E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦0.91 (E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦9.1 (E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.91 (E24 series)
0.047≦R≦0.091 (E24 series)
MCR10
EZH
0.25
1.51
-55 ~ +155
MCR18
MCR25
MCR50
EZH
JZH
JZH
0.25
0.5
1.51
2.13
2.13
-55 ~ +155
-55 ~ +155
-55 ~ +155
0.1≦R≦9.1
(E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦0.91 (E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦9.1 (E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦0.91 (E24 series)
0.047≦R≦0.091 (E24 series)
0.1≦R≦0.13 (E24 series)
0.15≦R≦9.1 (E24 series)
0.5
500±300
400±200
±250
500±300
400±200
±250
MCR100
JZH
1
3.01
-55 ~ +125
*Design and specifications are subject to change without notice.Carefullycheck the specification sheet supplied with the product
before using or ordering it.
www.rohm.com
©2016 ROHMCo., Ltd.All rights reserved.
2/6
2017.01 - Rev.G
MCR series - lowohmic -
Datasheet
●Chip resistor dimensions and markings
<Marking method>
There are three or four digits used for the calculation number
according to IEC code and "R"is used for the decimal point.
(Unit:mm)
Marking
Part No. Type code (mm)
(inch)
0201
L
W
t
a
b
existence
MCR006
MCR01
MCR03
MCR10
MCR18
MCR25
MCR50
MCR100
YLP
MZP
EZP
EZH
EZH
JZH
JZH
JZH
0603
1005
1608
2012
3216
3225
5025
6432
0.6±0.03
0.3±0.03
0.23±0.03
0.1±0.05
0.15±0.05
No
No
+0.05
0.25
0402
0603
0805
1206
1210
2010
2512
1.00±0.05
1.60±0.10
2.0±0.10
0.50±0.05
0.80±0.10
1.25±0.10
1.60±0.15
2.50±0.15
2.50±0.15
3.20±0.15
0.35±0.05
0.45±0.10
0.55±0.10
0.55±0.10
0.55±0.10
0.55±0.15
0.55±0.15
0.20±0.10
0.30±0.20
0.4±0.20
-0.10
0.30±0.20
0.4±0.20
3digits
Yes
Yes
Yes
Yes
Yes
3.20±0.15
3.20±0.15
5.00±0.15
6.30±0.15
0.50±0.25
0.50±0.25
0.60±0.25
0.60±0.25
0.50±0.25
0.50±0.25
0.60±0.25
0.60±0.25
●Land pattern example
(Unit:mm)
D
Dimensions
Part No.
Type code
YLP
A
B
C
MCR006
0.3
0.5
1.0
1.2
2.2
2.2
3.8
5.1
0.84
1.3
2.0
2.6
4.0
4.0
6.0
8.1
0.3
0.5
0.8
1.15
1.5
2.3
2.3
3.0
0.27
0.4
0.5
0.7
0.9
0.9
1.1
1.5
MCR01
MCR03
MCR10
MCR18
MCR25
MCR50
MCR100
MZP
EZP
EZH
EZH
JZH
JZH
JZH
www.rohm.com
©2016 ROHMCo., Ltd.All rights reserved.
3/6
2017.01 - Rev.G
MCR series - lowohmic -
Datasheet
●Derating curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.
■MCR006 / 100
■MCR01 / 03 / 10 / 18 / 25 / 50
●Characteristics
Test items
Guaranteedvalue
Test conditions
Resistance
See "Products list"
See "Products list"
±(2.0%+0.005Ω)
20℃
Variation of resistance
with temperature
Measurement:+25/-55, +25/+125℃
Rated voltage(current)×2.5, 2s
Maximum overload voltage
Overload
Anew uniform coating of minimum of 95%of
the surface being immersed and no
soldering damage.
Rosin-ethanol solution25%(Wweight)
Soldering condition:245±5℃
Duration of immersion:2.0±0.5s
Solderability
±(1.0%+0.005Ω)
Soldering condition:260±5℃
Resistance to
soldering heat
No remarkable abnormalityon the appearance. Duration of immersion:10±1s
Test temp:
-55℃~+125℃ 100cycle(MCR006)
-55℃~+125℃ 5cycle(MCR01/03/10/18/25/50/100)
Rapid change of
temperature
±(1.0%+0.005Ω)
±(3.0%+0.005Ω)
±(3.0%+0.005Ω)
40 ℃,93%(Relative humidity)
Test time:1,000h~1,048h
Damp heat, steadystate
Rated voltage(current),70℃±3℃
1.5h:ON-0.5h:OFF
Endurance at 70℃
Test time:1,000h~1,048h
125℃(MCR006/100)
Endurance
±(3.0%+0.005Ω)
155℃(MCR01/03/10/18/25/50)
Test time:1,000h~1,048h
±(1.0%+0.005Ω)※ MCR006only
±(0.5%+0.005Ω)
23±5℃, Immersion cleaning, 5±0.5min,
Solvent: 2-propanol
Resistance to solvent
Bend strength of
the end face plating
Without mechanical damage such as breaks.
-
Compliance Standard(s) : IEC60115-8
JISC 5201-8
※Maximum overload voltage (Test voltage)
MCR006 MCR01 MCR03 MCR10 MCR18 MCR25 MCR50 MCR100
1.34V
1.52V
1.90V
3.02V 3.02V 4.26kV 4.26kV 6.02V
www.rohm.com
©2016 ROHMCo., Ltd.All rights reserved.
4/6
2017.01 - Rev.G
MCR series - lowohmic -
Datasheet
●Tape dimensions
■Paper tape
(Unit : mm)
B0
Type
code
Part No.
W
F
E
A0
MCR006 YLP 8.0±0.2
MCR01 MZP 8.0±0.3
MCR03 EZP 8.0±0.3
MCR10 EZH 8.0±0.3
MCR18 EZH 8.0±0.3
3.5±0.05 1.75±0.1 0.38±0.03 0.68±0.03
3.5±0.05 1.75±0.1
3.5±0.05 1.75±0.1
0.7±0.1
1.2±0.1
1.9±0.1
1.1±0.1
+0.2
+0.2
2.4
3.5±0.05 1.75±0.1 1.65
3.5±0.05 1.75±0.1 1.95
-0.1
-0.1
+0.1
-0.05
+0.15
-0.05
3.5
Type
code
Part No.
D0
P0
P1
P2
T2
+0.1
0
+0.1
0
+0.1
0
+0.1
0
MCR006 YLP Φ1.5
MCR01 MZP Φ1.5
MCR03 EZP Φ1.5
MCR10 EZH Φ1.5
MCR18 EZH Φ1.5
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
2.0±0.05 2.0±0.05 MAX0.50
2.0±0.05 2.0±0.05 MAX1.1
4.0±0.1
4.0±0.1
4.0±0.1
2.0±0.05 MAX1.1
2.0±0.05 MAX1.1
2.0±0.05 MAX1.1
+0.1
0
(Unit : mm)
B0
■Embossed tape
Type
Part No.
W
F
E
A0
code
MCR25 JZH 8.0±0.3
MCR50 JZH 12.0±0.3
MCR100 JZH 12.0±0.3
3.5±0.05 1.75±0.1
5.5±0.05 1.75±0.1
5.5±0.05 1.75±0.1
3.0±0.1
3.4±0.2
3.5±0.2
3.5±0.1
5.6±0.2
6.7±0.2
Type
code
Part No.
D0
P0
P1
P2
T2
+0.1
0
+0.1
0
+0.1
0
MCR25 JZH Φ1.5
MCR50 JZH Φ1.5
MCR100 JZH Φ1.5
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
2.0±0.05 MAX1.1
2.0±0.05 MAX1.1
2.0±0.05 MAX1.1
www.rohm.com
©2016 ROHMCo., Ltd.All rights reserved.
5/6
2017.01 - Rev.G
MCR series - lowohmic -
Datasheet
●Reel dimensions
①MCR 006/01/03/10/18/25/50/100
②MCR 006/01/03/10/18/25
(Unit : mm)
D
Part No.
MCR006
MCR01
MCR03
MCR10
MCR18
MCR25
MCR50
MCR100
Type code
YLP
MZP
EZP
EZH
EZH
JZH
A
B
C
+1.0
0
9
0
-1.5
+1.0
0
Φ180
Φ60
Φ13±0.2
JZH
JZH
+1.0
0
13
www.rohm.com
©2016 ROHMCo., Ltd.All rights reserved.
6/6
2017.01 - Rev.G
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Datasheet
Buy
MCR18EZHFL - Web Page
Distribution Inventory
Part Number
Package
Unit Quantity
MCR18EZHFL
5000
Minimum Package Quantity
Packing Type
Constitution Materials List
RoHS
5000
Taping
inquiry
Yes
相关型号:
MCR100JZHJR47
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.47ohm, 200V, 5% +/-Tol, 250ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJR56
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.56ohm, 200V, 5% +/-Tol, 250ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJR82
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.82ohm, 200V, 5% +/-Tol, 250ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJS0.051OHM
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.051ohm, 3.01V, 5% +/-Tol, 800ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJS0.056OHM
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.056ohm, 3.01V, 5% +/-Tol, 800ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJS0.068OHM
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.068ohm, 3.01V, 5% +/-Tol, 800ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJS0.075OHM
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.075ohm, 3.01V, 5% +/-Tol, 800ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJS0.082OHM
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.082ohm, 3.01V, 5% +/-Tol, 800ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJS0.091OHM
RESISTOR, METAL GLAZE/THICK FILM, 1W, 5%, 800ppm, 0.091ohm, SURFACE MOUNT, 2512, CHIP
ROHM
MCR100JZHJSR047
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.047ohm, 3.01V, 5% +/-Tol, 500ppm/Cel, Surface Mount, 2512, CHIP
ROHM
MCR100JZHJSR056
Fixed Resistor, Metal Glaze/thick Film, 1W, 0.056ohm, 3.01V, 5% +/-Tol, 800ppm/Cel, Surface Mount, 2512, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明