MCR10EZHFR180 [ROHM]
RESISTOR, METAL GLAZE/THICK FILM, 0.125W, 1%, 250ppm, 0.18ohm, SURFACE MOUNT, 0805, CHIP;型号: | MCR10EZHFR180 |
厂家: | ROHM |
描述: | RESISTOR, METAL GLAZE/THICK FILM, 0.125W, 1%, 250ppm, 0.18ohm, SURFACE MOUNT, 0805, CHIP 电阻器 |
文件: | 总6页 (文件大小:105K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MCR10
Resistors
Thick film rectangular
MCR10 (2012 size : 1 / 8W
)
zFeatures
1) Power rating of 1 / 8W
2) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Leading the world in development and mass production.
Since start of production in 1982 (first in the wold), this component has established a solid reputation as a
general–purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or
ordering it.
zRatings
Item
Conditions
Specifications
0.125W (1 / 8W)
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
at 70°C
100
80
60
40
20
0
−55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
P: Rated power (W)
E= P×R
R: Nominal resistance (Ω)
Limiting element voltage
150V
Nominal resistance
See Table 1.
Operating temperature
−55°C to + 55°
C
Rev.A
1/5
MCR10
Resistors
Table 1
Jumper type
Resistance range
Resistance temperature coefficient
Resistance
Max. 50mΩ
2A
Resistance tolerance
(Ω)
(ppm/°C)
Rated current
0.1 ≤ R < 0.15
400 200
(E24)
(E24)
(E24,96)
(E24)
(E24)
(E24)
(E24)
F ( 1%)
Operating temperature
−55°C to +155°C
0.15 ≤ R <10
10 ≤ R ≤ 2.2M
0.1 ≤ R < 0.15
0.15 ≤ R < 1
1.0 ≤ R < 2.2
2.2 ≤ R < 10
250
100
400 200
250
J
( 5%)
500 350
500
10 ≤ R ≤ 10M (E24)
200
zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
z
Characteristics
Guaranteed value
Resistor type Jumper type
J : 5% Max. 50mΩ
Item
Resistance
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
F : 1%
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum overload voltage : 200V
Overload
(2.0%+0.1Ω)
Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
Max. 50mΩ
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
Rapid change of
temperature
Max. 100mΩ
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
Damp heat, steady state
(3.0%+0.1Ω)
Max. 100mΩ
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
(1.0%+0.05Ω)
Max. 100mΩ
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.25.3
155°C
Endurance
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
JIS C 5201-1 4.33
Bend strength of
the end face plating
Without mechanical damage such as breaks.
Rev.A
2/5
MCR10
Resistors
zExternal dimensions (Unit : mm)
1
0.4 0.2
2
3
No.
1
Material
Resistive element
(Oxide metal thick film)
Silver thick film electrode
Nickel electrode
0.4 0.2
2.0 0.1
4
2
3
4
5
6
5
Sn electrode
Alumina substrate
Overcoating
6
z
Packaging
Reel
Taping
P
0
P
2
P1
φD0
E
F
W
B
0
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
mount
T
2
C
(Unit: mm)
Label
W
F
E
A
0
B0
EIAJ ET-7200B compliant
+0.2
−0.1
+0.2
−0.1
8.0±0.3
3.5±0.05
1.75±0.1
1.65
2.4
(Unit: mm)
D
D
0
P
0
P
1
P
2
T2
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max. 1.1
A
B
C
φ1.5
0
−1.5
+1.0
0
+1
0
φ180
9
φ60
φ13 0.2
Bulk case
Slider
Shutter
12 0.1
0
−0.2
36
110 0.7
(Unit : mm)
EIAJ ET-7201B compliant
Rev.A
3/5
MCR10
Resistors
zPart designation
M C R 1 0
E
Z H
J
L
Resistance tolerance Special part number Nominal resistance
Part No.
F
1%
10Ω or less (class F)
1Ω or less (class J)
Resistance code, 3 or 4 digits.
L
J
5%
Resistance
Resistance
tolerance
code
S
0.1Ω or less
+
Special P/N
FL,FS,JS
JL
:
:
4 digits
3 digits
Packaging Specifications Code
Resistance tolerance
J( 5%) F( 1%)
Part No.
Code
Packaging specifications
Paper tape (4mm Pitch)
Reel
Basic ordering unit(pcs)
,
MCR10
EZH
φ180mm (7in.)
5 000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
zDimensions
2.20
1.45
1.40
1.35
1.30
1.25
1.20
1.15
1.10
1.05
0.75
JIS C 5201-1 4.4.2
SAMPLE SIZE : n=20pcs
MICROMETER
JIS C 5201-1 4.4.2
SAMPLE SIZE : n=20pcs
MICROMETER
JIS C 5201-1 4.4.2
SAMPLE SIZE : n=20pcs
MICROMETER
2.15
2.10
2.05
2.00
1.95
1.90
1.85
1.80
0.70
0.65
0.60
0.55
0.50
0.45
0.40
0.35
0.1
1
10 100 1k 10k 100k 1M 10M
0.1
1
10 100 1k 10k 100k 1M 10M
100
1k 10k 100k 1M 10M
0.1
1
10
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.2 Dimensions (length)
Fig.3 Dimensions (width)
Fig.4 Dimensions (thickness)
z
Electrical characteristics
8.0
4.0
3.0
900
700
JIS C 5201-1 4.8
SAMPLE SIZE : n=10pcs
25°C / −55°C
JIS C 5201-1 4.13
JIS C 5201-1 4.5
SAMPLE SIZE : n=20pcs
20°C 65%RH
SAMPLE SIZE : n=10pcs
RATED VOLTAGE×2.5
TIMES : 2s
6.0
4.0
500
25°C / 125°C
2.0
MAXIMUM OVERLOAD VOLTAGE : 200V
300
2.0
1.0
100
0.0
0.0
−100
−300
−500
−700
−900
−2.0
−4.0
−6.0
−8.0
−1.0
−2.0
−3.0
−4.0
0.1
1
10 100 1k 10k 100k 1M 10M
0.1
1
10 100 1k 10k 100k 1M 10M
0.1
1
10 100 1k 10k 100k 1M 10M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.5 Resistance
Fig.7 Overload
Fig.6 Variation resistance with
temperature
Rev.A
4/5
MCR10
Resistors
2.5
2.5
4.0
3.0
JIS C 5201-1 4.24
SAMPLE SIZE : n=10pcs
40°C 93%RH WITH NO LOAD 1,000h
JIS C 5201-1 4.18
SAMPLE SIZE : n=10pcs
SOLDERING CONDITION : 260°C 10s
JIS C 5201-1 4.19
SAMPLE SIZE : n=10pcs
−55°C / 125°C 5cyc
2.0
1.5
1.0
0.5
0.0
2.0
1.5
1.0
0.5
0.0
2.0
1.0
0.0
−0.5
−1.0
−1.5
−0.5
−1.0
−1.5
−1.0
−2.0
−3.0
−4.0
−2.0
−2.5
−2.0
−2.5
0.1
1
10 100 1k 10k 100k 1M 10M
0.1
1
10 100 1k 10k 100k 1M 10M
0.1
1
10 100 1k 10k 100k1M 10M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.10 Damp heat, steady state
Fig.8 Resistance to soldering heat
Fig.9 Rapid change of
temperature
4.0
4.0
3.0
2.0
1.5
JIS C 5201-1 4.25.1
JIS C 5201-1 4.29
SAMPLE SIZE : n=10pcs
IPA, 5min.
JIS C 5201-1 4.25.3
SAMPLE SIZE : n=10pcs
155°C WITH NO LOAD 1,000h
SAMPLE SIZE : n=10pcs
3.0
70°C 1,000h
OVERLOAD : THE RATED VOLTAGE
2.0
2.0
1.0
1.0
0.0
1.0
0.5
0.0
0.0
−1.0
−1.0
−2.0
−3.0
−4.0
−0.5
−1.0
−1.5
−2.0
−2.0
−3.0
−4.0
0.1
1
10 100 1k 10k 100k 1M 10M
0.1
1
10 100 1k 10k 100k 1M 10M
0.1
1
10 100 1k 10k 100k 1M 10M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.12 Endurance
Fig.11 Endurance at 70°C
Fig.13 Resistance to solvents
2.5
JIS C 5201-1 4.33
SAMPLE SIZE : n=10pcs
ENDURANCE WITH 90mm WIDTH
2.0
1.5
1.0
0.5
0.0
−0.5
−1.0
−1.5
−2.0
−2.5
0.1
1
10 100 1k 10k 100k 1M 10M
RESISTANCE (Ω)
Fig.14 Bend strength of
the end face plating
Rev.A
5/5
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
相关型号:
MCR10EZHFR187
RESISTOR, METAL GLAZE/THICK FILM, 0.125W, 1%, 250ppm, 0.187ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFR332
RESISTOR, METAL GLAZE/THICK FILM, 0.125W, 1%, 250ppm, 0.332ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFR340
RESISTOR, METAL GLAZE/THICK FILM, 0.125W, 1%, 250ppm, 0.34ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFR665
RESISTOR, METAL GLAZE/THICK FILM, 0.125W, 1%, 250ppm, 0.665ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFS0.047OHM
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 800ppm, 0.047ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFS0.056OHM
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 800ppm, 0.056ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFS0.062OHM
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 800ppm, 0.062ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFS0.068OHM
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 800ppm, 0.068ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFS0.075OHM
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 800ppm, 0.075ohm, SURFACE MOUNT, 0805, CHIP
ROHM
MCR10EZHFS0.082OHM
RESISTOR, METAL GLAZE/THICK FILM, 0.25W, 1%, 800ppm, 0.082ohm, SURFACE MOUNT, 0805, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明