MCR50LZHJ103 [ROHM]
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 10000ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP;型号: | MCR50LZHJ103 |
厂家: | ROHM |
描述: | Fixed Resistor, Metal Glaze/thick Film, 0.5W, 10000ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP |
文件: | 总6页 (文件大小:109K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MCR50
Resistors
Thick film rectangular
MCR50 (5025 size: 1 / 2W)
!Features
1) Made of same material as the general purpose chip resistors (MCR10 / 18).
2) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Both flow and reflow soldering can be used.
4) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice.
Carefully check the specification sheet supplied with the product before using or ordering it.
!Ratings
Item
Conditions
Specifications
0.5W (1 / 2W)
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70˚C.
Rated power
at 70˚
C
100
80
60
40
20
0
-55
0
70
100 125
˚C
AMBIENT TEMPERATURE
(
)
Fig.1
Max. operating voltage
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
200V
400V
400V
Max. overload voltage
E: Rated voltage (V)
E = P × R P: Rated power (W)
R: Nominal resistance (Ω)
Max. intermittent overload voltage
Nominal resistance
See Table 1.
Operating temperature
- 55˚
C to + 125˚C
Table 1
Jumper type
Resistance
Max. 50mΩ
3A
Resistance range
Resistance temperature coefficient
Resistance tolerance
(Ω)
(ppm / ˚C)
Rated current
Peak current
F
( ± 1%)
10 ≤ R < 100k (E24,96)
± 200
15A
100
1.0
2.2
≤
≤
≤
R
≤
<
<
180k (E24,96)
± 100
Operating temperature
- 55˚C to + 125˚C
R
R
2.2
(E24)
(E24)
(E24)
500 ± 350
± 500
J
( ± 5%)
10
10
≤
R
≤
330k
± 200
330k
<
R ≤ 560k (E24)
± 350
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
MCR50
Resistors
!Characteristics
Specifications
Chip resistance
F: ± 1%
Characteristics
Test method
Jumper type
Max. 50mΩ
JIS C 5202 5.1
DC resistance
J: ± 5%
Applied voltage: A
Resistance temperature
characteristics
JIS C 5202 5.2
Test conditions: + 25 / - 55 / + 25 / + 125˚C
See Table 1.
JIS C 5202 5.5
Rated voltage (current):× 2.5, 5s.
Maximum overload voltage: 400V
Short time overload
± (2.5% + 0.1Ω)
Max. 50mΩ
Min. 1,000MΩ between terminal and board
JIS C 5202 5.6
Test voltage: 100V, 1min.
Assembled state
Metal block
observation
point A
Insulation plate
Insulation resistance
Metal plate
Test resistor
Spring-loaded
pressure
Insulation
sheath
Observation
point B
R 0.5
JIS C 5202 5.7
Test voltage: 500V
Withstand voltage
Do not damage insulation or cause a short circuit.
JIS C 5202 5.8
Rated voltage (current):× 2.5
Intermittent overload
± (5.0% + 0.1Ω)
± (1.0% + 0.05Ω)
Max. 50mΩ
Max. 50mΩ
(1s: ON - 25s: OFF) × 10,000cyc.
Terminal strength
(against bending of circuit board)
JIS C 5202 6.1
There must be no mechanical damage.
JIS C 5202 6.4
Soldering conditions: 260 ± 5˚C
Soldering time: 10 ± 1s.
± (1.0% + 0.05Ω)
Max. 50mΩ
Resistance to soldering heat
Solderability
Outside must not be noticeably damaged.
JIS C 5202 6.5
95% of terminal surface must be covered by
new solder, and there must be
no soldering corrosion.
Rosin methanol: (25%WT)
Soldering conditions: 235 ± 5˚C
Soldering time: 2.0 ± 0.5s.
JIS C 5202 7.2
125˚C
± (3.0% + 0.1Ω)
± (3.0% + 0.1Ω)
Max. 100mΩ
Max. 100mΩ
Resistance to dry heat
Test time: 11,000 to 1,048 hrs.
JIS C 5202 7.10
Rated voltage (current) 70˚C
1.5h: ON - 0.5h: OFF
Endurance
(rated load)
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.9
Rated voltage (current) 60˚C, 95%Rh
1.5h: ON - 0.5h: OFF
Endurance
(under load in damp environment)
± (5.0% + 0.1Ω)
± (3.0% + 0.1Ω)
Max. 100mΩ
Max. 100mΩ
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.5
85˚C, 85%RH
Test time: 1,000 to 1,048 hrs.
Resistance to humidity
(steady state)
JIS C 5202 7.4
± (1.0% + 0.05Ω)
± (0.5% + 0.05Ω)
Max. 50mΩ
Test temperature: - 55˚C to + 125˚C 100cyc.
Temperature cycling
JIS C 5202 6.9
Room temperature, static immersion, 1 min.
Solvent: Isopropyl alcohol
Max. 100mΩ
Markings must not be dissolved away.
Resistance to solvents
MCR50
Resistors
!External dimensions (Units: mm)
0.6 ± 0.25
No.
Material
Thick dielectric glaze of ruthenium
(only silver used for jumper)
0.6 ± 0.25
5.0 ± 0.15
Thick film of palladium-silver for primary electrode
Nickel-coated secondary electrode
External electrode coated with tin and lead
Alumina substrate
Overcoating
!Packaging
Reel
Taping
P
0
P2
D0
φ
A
B
D
K
A
0
P1
C
(Units: mm)
Label
W
F
E
A0
B0
EIAJ ET-7001 compliant
12.0 0.3 5.5 0.05 1.75 0.1
3.4 0.2
5.6 0.2
K
(Units: mm)
D
A
B
C
D0
P
0
P
1
P2
+ 0.1
0
0
+ 1
0
φ1.5
4.0 0.1
4.0 0.1
2.0 0.05
Max. 1.1
φ180
φ60
13 0.3
φ13 0.2
– 3
MCR50
Resistors
!Makeup of the part number
Part No.
3-digit or 4-digit IEC coding system
Nominal resistance
Packaging / Processing specifications
Resistance tolerance
± 1% ± 5%
special part number
Standard ordering
unit(pcs)
10Ω or more (F class)
F
J
Part No.
MCR50
Code
JZH
Packaging
Paper tape
Shipped to
World wide
World wide
Blank
1Ω or more (J class)
Specify "J" for jumper also.
4,000
LZH
10,000
!Dimensions
5.40
0.75
0.70
0.65
0.60
0.55
0.50
0.45
0.40
0.35
2.80
2.70
2.60
2.50
2.40
2.30
2.20
JIS C 5202 4.3
SAMPLE SIZE : n = 20pcs
MICROMETER
JIS C 5202 4.3
SAMPLE SIZE : n = 20pcs
MICROMETER
JIS C 5202 4.3
SAMPLE SIZE : n = 20pcs
MICROMETER
5.30
5.20
5.10
5.00
4.90
4.80
4.70
4.60
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.2 Dimensions (length)
Fig.3 Dimensions (width)
Fig.4 Dimensions (thickness)
!Electrical characteristics
4.0
3.0
6.0
900
700
JIS C 5202 5.2
SAMPLE SIZE : n = 10pcs
25˚C / - 55˚C
JIS C 5202 5.5
JIS C 5202 5.1
SAMPLE SIZE : n = 20pcs
20˚C 65%RH
SAMPLE SIZE : n = 10pcs
RATED VOLTAGE × 2.5
TIMES 5s
4.0
500
25˚C / 125˚C
2.0
MAXIMUM OVERLOAD VOLTAGE : 400V
2.0
0
300
1.0
100
0
- 100
- 300
- 500
- 700
- 900
- 1.0
- 2.0
- 3.0
- 4.0
- 2.0
- 4.0
- 6.0
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
0.68 2.2 10 100 1k 10k 100k 560k
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.5 DC resistance
Fig.7 Short time overload
Fig.6 Resistance temperature
characteristics
MCR50
Resistors
100
50
2.0
1.5
6.0
5.0
JIS C 5202 5.7
JIS C 5202 5.8
SAMPLE SIZE : n = 10pcs
METALLIC BLOCK METHOD :
TEST VOLTAGE 500V 1min.
SAMPLE SIZE : n = 10pcs
RATED VOLTAGE × 2.5TIMES
1s-ON 25s-OFF 10,000cyc
MAXIMUM INTERMITTED OVER LOAD
VOLTAGE : 400V
4.0
3.0
1.0
2.0
20
10
5
0.5
1.0
0
0
- 1.0
- 2.0
- 3.0
- 4.0
- 5.0
- 6.0
- 0.5
- 1.0
- 1.5
- 2.0
JIS C 5202 5.6
2
1
SAMPLE SIZE : n = 10pcs
METALLIC BLOCK METHOD :
TEST VOLTAGE 100V 1min.
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.8 Insulation resistance
Fig.9 Withstand voltage
Fig.10 Intermittent overload
2.0
1.5
2.5
2.0
1.5
1.0
0.5
0
4.0
3.0
JIS C 5202 6.1
SAMPLE SIZE : n = 10pcs
ENDURANCE WITH 90mm WIDTH
JIS C 5202 6.4
SAMPLE SIZE : n = 10pcs
SOLDERING CONDITION : 260˚C 10s
JIS C 5202 7.2
SAMPLE SIZE : n = 10pcs
125˚C WITH NO LOAD 1,000h
1.0
2.0
0.5
1.0
0
0
- 0.5
- 1.0
- 1.5
- 2.0
- 2.5
- 0.5
- 1.0
- 1.5
- 2.0
- 1.0
- 2.0
- 3.0
- 4.0
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1 k 10k 100k 560k
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.11 Terminal strength (bendi-
ngl strength characteristics)
Fig.13 Resistance to dry heat
Fig.12 Resistance to soldering heat
4.0
6.0
4.0
3.0
JIS C 5202 7.10
SAMPLE SIZE : n = 10pcs
70˚C 1,000h
OVERLOAD : THE RATED VOLTAGE
JIS C 5202 7.9
SAMPLE SIZE : n = 10pcs
60˚C 95%RH 1,000h
OVERLOAD : THE RATED VOLTAGE
JIS C 5202 7.5
SAMPLE SIZE : n = 10pcs
85˚C 85%RH WITH NO LOAD 1,000h
3.0
4.0
2.0
0
2.0
1.0
2.0
1.0
0
0
- 1.0
- 2.0
- 3.0
- 4.0
- 1.0
- 2.0
- 3.0
- 4.0
- 2.0
- 4.0
- 6.0
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.14 Endurance (rated load)
Fig.15 Endurance (under load in
damp environment)
Fig.16 Resistance to humidity
(steady state)
MCR50
Resistors
1.0
0.8
2.0
1.5
JIS C 5202 6.9
SAMPLE SIZE : n = 10pcs
IPA, 1min.
JIS C 5202 7.4
SAMPLE SIZE : n = 10pcs
- 55˚C / 125˚C 100cyc
0.6
1.0
0.4
0.2
0.5
0
0
- 0.2
- 0.4
- 0.6
- 0.8
- 1.0
- 0.5
- 1.0
- 1.5
- 2.0
0.68
1
10 100 1k 10k 100k 560k
0.68
1
10 100 1k 10k 100k 560k
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig. 18 Resistance to solvents
Fig.17 Temperature cycling
相关型号:
MCR50LZHJ111
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 110ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP
ROHM
MCR50LZHJ122
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 1200ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP
ROHM
MCR50LZHJ131
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 130ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP
ROHM
MCR50LZHJ152
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 1500ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP
ROHM
MCR50LZHJ162
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 1600ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP
ROHM
MCR50LZHJ182
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 1800ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP
ROHM
MCR50LZHJ620
Fixed Resistor, Metal Glaze/thick Film, 0.5W, 62ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 2010, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明