MNR02M0AJ202 [ROHM]
RESISTOR, NETWORK, FILM, ISOLATED, 0.063W, SURFACE MOUNT, 0404, CHIP;
| 型号： | MNR02M0AJ202 |
| 厂家： | 
ROHM |
| 描述： | RESISTOR, NETWORK, FILM, ISOLATED, 0.063W, SURFACE MOUNT, 0404, CHIP |
| 文件： | 总6页 (文件大小：99K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MNR02
Resistors
Chip resistor networks
MNR02 (1005 × 2 size)
zFeatures
1) Extremely small and light
Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%.
2) High-density mounting
Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced.
3) Compatible with a wide range of mounting equipment.
Squared corners make it excellent for mounting using image recognition devices.
4) Convex electrodes
Easy to check the fillet after soldering is finished.
5) ROHM resistors have obtained ISO-9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or
ordering it.
zRatings
Item
Conditions
Specifications
0.063W (1 / 16W)
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
at 70°C
100
80
60
40
20
0
−55
0
70
100 125
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
P: Rated power (W)
E = P×R
Limiting element voltage
25V
R: Nominal resistance (Ω)
Nominal resistance See Table 1.
Operating temperature
−55°C to +125°C
Rev.A
1/5
MNR02
Resistors
Table 1
Resistance range
Resistance temperature coefficient
Resistance tolerance
J ( 5%)
(Ω)
(ppm / °C)
10≤R≤1M
(E24)
300
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
zCharacteristics
Guaranteed value
Items
Resistance
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistor type
J : 5%
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage×2 : 50V
Overload
(2.0%+0.1Ω)
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
Rapid change of
temperature
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
Damp heat, steady state
(3.0%+0.1Ω)
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
JIS C 5201-1 4.25.3
125°C
Endurance
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
(1.0%+0.05Ω)
Without mechanical damage such as breaks.
JIS C 5201-1 4.33
Bend strength of
the end face plating
Rev.A
2/5
MNR02
Resistors
zExternal dimensions (Unit: mm)
1.0 0.1
B
6
1
Cross section A-A'
Cross section B-B'
No.
1
Material
Thick dielectric glaze of oxide metal
Thick film of silver for electrode
Nickel-coated electrode
Sn electrode
5
2
6
1
A
A'
3
4
5
2
5
Alumina substrate
3
4
B'
6
Overcoating
0.35 0.1
+0.1
+0.05
−0.1
0.33
0.34
−0.05
0.68
zEquivalent circuit
R1
R2
R1 = R2
Rev.A
3/5
MNR02
Resistors
zPackaging
Reel
Taping
P
0
P
2
φ
D
0
E
F
A
0
W
A
B
D
P
1
Heat crimp cover / Tape
Chip network
resistors
Thick paper (Underside paper tape)
mount
Square punchout hole
T
2
C
Label
(Unit: mm)
EIAJ ET-7200B compliant
W
F
E
A0
B0
(Unit: mm)
D
8.0 0.3
3.5 0.05
1.75 0.1
1.17 0.1
1.17 0.1
A
B
C
D
0
P
0
P
1
P
2
T2
0
−1.5
+1
0
+1.0
0
φ180
φ60
9
φ13 0.2
+0.1
4.0 0.1
2.0 0.1
2.0 0.05
Max. 0.5
φ1.5
0
zProduct designation
P
Part No.
Resistance tolerance Nominal resistance
J
5%
Resistance code, 3 digits,
000 denotes Jumper type.
J is also used
for jumper.
Packaging Specifications Code
Resistance tolerance
J( 5%)
Part No. Code
MNR02 M0AP
Packaging specifications
Reel
Basic ordering unit (pcs)
Paper tape (2mmPitch) φ180mm (7in).
10,000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
Rev.A
4/5
MNR02
Resistors
zElectrical characteristics
6.0
6.0
4.0
400
JIS C 5201-1 4.13
JIS C 5201-1 4.5
SAMPLE SIZE : n=40pcs
20°C 65%RH
JIS C 5201-1 4.8
SAMPLE SIZE : n=20pcs
25°C / −55°C 25°C / 125°C
5.0
SAMPLE SIZE : n=20pcs
RATED VOLTAGE×2.5TIMES 2s
LIMITING ELEMENT VOLTAGE×2 : 100V
300
200
4.0
3.0
2.0
2.0
0
100
1.0
0
0
−1.0
−2.0
−3.0
−4.0
−5.0
−6.0
−100
−200
−300
−400
−2.0
−4.0
−6.0
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.2 Resistance
Fig.4 Overload
Fig.3 Variation resistance with
temperature
6.0
4.0
2.0
3.0
3.0
2.0
JIS C 5201-1 4.18
JIS C 5201-1 4.24
JIS C 5201-1 4.19
SAMPLE SIZE : n=20pcs
−55°C / 125°C 5cyc
SAMPLE SIZE : n=20pcs
SOLDERING CONDITION
: 260°C 10s
SAMPLE SIZE : n=20pcs
40°C 93%RH WITH NO LOAD
1,000h
2.0
1.0
1.0
0
0
0
−2.0
−1.0
−2.0
−3.0
−1.0
−2.0
−3.0
−4.0
−6.0
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.6 Rapid change of
temperature
Fig.7 Damp heat, steady state
Fig.5 Resistance to soldering heat
6.0
4.0
6.0
JIS C 5201-1 4.25.1
SAMPLE SIZE : n=20pcs
70°C 1,000h
JIS C 5201-1 4.25.3
SAMPLE SIZE : n=20pcs
125°C WITH NO LOAD 1,000h
4.0
2.0
OVERLOAD : THE RATED VOLTAGE
2.0
0
0
−2.0
−4.0
−6.0
−2.0
−4.0
−6.0
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.9 Endurance
Fig.8 Endurance at 70°C
Rev.A
5/5
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
相关型号：
©2020 ICPDF网 联系我们和版权申明