MNR02M0APJ333 [ROHM]
暂无描述;型号: | MNR02M0APJ333 |
厂家: | ROHM |
描述: | 暂无描述 |
文件: | 总4页 (文件大小:166K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Compact Chip Resistor Networks
MNR02 (1005 2 size)
Features
1) Extremely small and light
Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%.
2) High-density mounting
Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced.
3) Compatible with a wide range of mounting equipment.
Squared corners make it excellent for mounting using image recognition devices.
4) Convex electrodes
Easy to check the fillet after soldering is finished.
5) ROHM resistors have obtained ISO9001- / ISO/TS 16949- certification.
Ratings
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering
it.
Item
Conditions
Specifications
0.063W (1 / 16W)
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
at 70°C
100
80
60
40
20
0
−55
0
70
100 125
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
P: Rated power (W)
E = P×R
Limiting element voltage
25V
R: Nominal resistance (Ω)
Nominal resistance See Table 1.
Operating temperature
−55°C to +155°C
Jumper type
Resistance
Max. 50mΩ
1A
Rated current
Operating temperature
Table 1
−55°C to +155°C
Resistance range
Resistance temperature coefficient
Resistance tolerance
J ( 5%)
(Ω)
(ppm / °C)
10 to 1M (E24)
200
Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
www.rohm.com
2011.12 - Rev.F
1/3
c
○ 2011 ROHM Co., Ltd. All rights reserved.
Data Sheet
MNR02 (1005 2 size)
Characteristics
Guaranteed value
Items
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistor type
J : 5%
Jumper type
MAX.50mΩ
Resistance
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : +25 / +125°C
See Table.1
(2.0%+0.1Ω)
MAX.50mΩ
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage×2 : 50V
Overload
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
MAX.50mΩ
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
No remarkable abnormality on the appearance.
MAX.50mΩ
(1.0%+0.05Ω)
(3.0%+0.1Ω)
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
Rapid change of
temperature
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
MAX.100mΩ
Damp heat, steady state
(3.0%+0.1Ω)
JIS C 5201-1 4.25.1
MAX.100mΩ
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
(1.0%+0.05Ω)
JIS C 5201-1 4.25.3
125°C
MAX.100mΩ
MAX.50mΩ
Endurance
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
MAX.50mΩ
JIS C 5201-1 4.33
Bend strength of
the end face plating
Without mechanical damage such as breaks.
Dimensions (Unit: mm)
1.0 0.1
B
6
1
No.
1
Material
Resistive element (Oxide metal thick film)
Silver thick film electrode
Nickel electrode
Cross section A-A'
Cross section B-B'
5
2
6
1
3
A
A'
4
Sn electrode
5
Alumina substrate
5
2
6
Overcoating (Resin)
3
4
B'
0.35 0.1
+0.1
+0.05
−0.1
0.33
0.34
−0.05
0.68
Equivalent circuit
R1
R2
R1 = R2
www.rohm.com
2011.12 - Rev.F
2/3
c
○ 2011 ROHM Co., Ltd. All rights reserved.
Data Sheet
MNR02 (1005 2 size)
Packaging
Reel
Taping
P0
P2
φ
D
0
E
F
A0
W
A
B
D
P
1
Heat crimp cover / Tape
Chip network
resistors
Thick paper (Underside paper tape)
mount
Square punchout hole
T
2
C
Label
EIAJ ET-7200B (RRM) compliant
(Unit: mm)
W
F
E
A
0
B0
8.0 0.3
3.5 0.05
1.75 0.1
1.17 0.1
1.17 0.1
D0
P0
P1
P
2
T2
+0.1
4.0 0.1
2.0 0.1
2.0 0.05
Max. 0.5
φ1.5
0
A
B
D
Label
C
EIAJ ET-7200B (RRV) compliant
(Unit: mm)
D
A
B
C
0
−1.5
+1
0
+1.0
0
φ180
φ60
9
φ13 0.2
Part No. Explanation
P
Part No.
Resistance tolerance
Nominal resistance
J
5%
Resistance code, 3
000 denotes jumper type.
J is also used
for jumper.
Resistance
tolerance
Resistance
code
Packaging Specifications Code
:
3digits
J
Resistance tolerance
J( 5%)
Part No. Code
Packaging specifications
Reel
Basic ordering unit (pcs)
MNR02 M0AP
Paper tape (2mmPitch)
φ180mm
10,000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
www.rohm.com
2011.12 - Rev.F
3/3
c
○ 2011 ROHM Co., Ltd. All rights reserved.
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
R1120
A
相关型号:
MNR02M0APJ334
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 330000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ360
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 36ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ361
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 360ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ363
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 36000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ364
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 360000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ472
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 4700ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ560
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 56ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ562
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 5600ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ624
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 620000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ682
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 6800ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ750
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 75ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ753
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 75000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明