MNR04M0APJ155 [ROHM]

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0804, CHIP;


型号：	MNR04M0APJ155
厂家：	ROHM
描述：	Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0804, CHIP
文件：	总5页 (文件大小：87K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MNR04

Resistors

Compact Chip Resistor Networks

MNR04 (1005 × 4 size)

zFeatures

1) Extremely small and light

Area ratio is 60% smaller than that of chip 3216 (MNR14), while weight ratio has been cut 75%.

2) High-density mounting

Can be mounted even more densely than four 1005 chips (MCR01), and mounting costs are lower.

3) Can be mounted on a wide variety of devices

Squared corners make it excellent for mounting on image recognition devices.

4) Convex electrodes

Easy to check the fillet after soldering is finished.

5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.

Furthermore, changes to the design and specifications of products may occur without notice. Therefore, before

ordering or using this product, please make sure to reconfirm the specification sheet before ordering or using this

product.

zRatings

Item

Conditions

Specifications

0.063W (1 / 16W)

Rated power

Power must be derated according to the power derating curve in

at 70°C

Figure 1 when ambient temperature exceeds 70°C.

100

Ð 55

100 125

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation. If the

value obtained exceeds the limiting element voltage, the voltage

rating is equal to maximum operating voltage.

E : Voltage rating (V)

E = P×R

P : Power rating (W)

R : Nominal resistance (Ω)

Limiting element voltage 25V

Nominal resistance

See Table 1.

Operating temperature

−55°C to +125°C

Rev.E

1/4

MNR04

Resistors

Jumper type

Table 1

Resistance range

Resistance temperature

coefficient (ppm / °C)

Resistance

Max.50mΩ

Resistance tolerance

J ( 5%)

(Ω)

Rated current

10≤R≤1M

(E24)

200

Operating temperature −55°C to +125°C

•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

zCharacteristics

Guaranteed value

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

J : 5%

Jumper type

Max. 50mΩ

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 50V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Rev.E

2/4

MNR04

Resistors

zDimensions (Unit : mm)

2.0 0.2

a : 0.4 0.1

b : 0.3 0.1

No.

Material

Thick dielectric glaze of oxide metal

Thick film of silver for electrode

Nickel-coated electrode

Sn electrode

Alumina substrate

∗

0.5

Overcoating

Cross section A - A'

Cross section B - B'

∗ The pitch between electrodes.

zEquivalent circuit

R1 = R2 = R3 = R4

Rev.E

3/4

MNR04

Resistors

zPackaging

Reel

Taping

φD

Thick paper mount

Heat crimp cover / Tape

Chip network resistors

Square punchout hole

(Underside paper tape)

Label

(Unit : mm)

EIAJ ET-7200B compliant

(Unit : mm)

8.0 0.3

3.5 0.05

1.75 0.1

1.2 0.1

2.2 0.1

−1.5

+1.0

φ180

φ60

φ13 0.2

+0.1

4.0 0.1

2.0 0.05

Max. 1.1

φ1.5

zPart No. Explanation

M N R 0 4 M 0 A P

Part No.

Resistance tolerance

Nominal resistance

Resistance code,3 digits,

000 denotes Jumper type.

J is also used

for jumper

Packaging Specifications Code

Resistance tolerance

Part No.

Code

Packaging specifications

Paper tape (2mm Pitch)

Reel

Basic ordering unit (pcs)

(

)

10 000

MNR04

M0AP

φ180mm (7inch)

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

Rev.E

4/4

Appendix

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level

of reliability and the malfunction of which would directly endanger human life (such as medical

instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers

and other safety devices), please be sure to consult with our sales representative in advance.

It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance

of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow

for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in

order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM

cannot be held responsible for any damages arising from the use of the products under conditions out of the

range of the specifications or due to non-compliance with the NOTES specified in this catalog.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

THE AMERICAS / EUPOPE / ASIA / JAPAN

ROHM Customer Support System

www.rohm.com

TEL : +81-75-311-2121

FAX : +81-75-315-0172

21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan

Appendix1-Rev2.0

MNR04M0APJ155 [ROHM]

相关型号：

MNR04M0APJ182

MNR04M0APJ225

MNR04M0APJ243

MNR04M0APJ245

MNR04M0APJ273

MNR04M0APJ274

MNR04M0APJ275

MNR04M0APJ302

MNR04M0APJ330

MNR04M0APJ331

MNR04M0APJ333

MNR04M0APJ335