MNR12E0APF2203 [ROHM]

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 220000ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0606, CHIP;


型号：	MNR12E0APF2203
厂家：	ROHM
描述：	Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 220000ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0606, CHIP 电阻器
文件：	总5页 (文件大小：75K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MNR12

Resistors

Compact Chip Resistor Networks

MNR12 (0603×2 size)

zFeatures

1) Convex electrodes

Easy to check the fillet after soldering is finished.

2) Small, light, rectangular 2-chip network

Area ratio is 65% smaller than that of MNR32, while weight ratio has been cut 75%.

3) High-density mounting

Can be mounted even more densely than two 0603 chips (MCR03), and mounting costs are lower.

4) Compatible with a wide range of mounting equipment.

Squared corners make it excellent for mounting using image recognition devices.

5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with

the product before using or ordering it.

zRatings

Item

Rated power

Conditions

Specifications

0.063W (1 / 16W)

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

at 70°C

100

−55

100 125

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

E= P×R

Limiting element voltage 50V

R: Nominal resistance (Ω)

Nominal resistance

See Table 1.

Operating temperature

−55°C to +125°C

Rev.H

1/4

MNR12

Resistors

Jumper type

Table 1

Resistance range

Resistance temperature coefficient

Resistance

Max. 50mΩ

Resistance tolerance

(Ω)

(ppm / °C)

Rated current

J ( 5%)

F ( 1%)

10 to 1M (E24)

200

Operating temperature −55°C to +125°C

100

•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

zCharacteristics

Guaranteed value

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

Jumper type

Max. 50mΩ

J : 5%

F : 1%

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Maximum Overload Voltage : 100V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Rev.H

2/4

MNR12

Resistors

zDimensions (Unit : mm)

0.6 0.15

No.

Material

Resistive element

(Oxide metal thick film)

Silver thick film electrode

Nickel electrode

Cross section A-A'

0.3 0.2

103

Cross section B-B'

0.3 0.2

Sn electrode

Alumina substrate

0.8

Overcoating (Resin)

1.6 0.1

0.4 0.15

0.6 0.15

∗

Making may change to the one-character type.

∗∗ Pitch of the upper electrode.

zEquivalent circuit

R1 = R2

zPackaging

Taping

Reel

φD0

Heat crimp cover / Tape

Chip network

resistor

Thick paper (Underside paper tape)

mount

Square punchout hole

(Unit : mm)

Label

EIAJ ET-7200B compliant

8.0 0.3

3.5 0.05

1.75 0.1

1.8 0.1

(Unit : mm)

−1.5

+1.0

+0.1

φ180

φ60

φ13 0.2

φ1.5

4.0 0.1

2.0 0.05

Max. 1.1

Rev.H

3/4

MNR12

Resistors

zPart No. Explanation

M N R 1 2 E 0 A P J

Part No.

Resistance tolerance

Nominal resistance

Resistance code, 3 or 4 digits.

000 denotes jumper type.

Resistance

tolerance

Resistance

code

J is also used

for jumper

4 digits

3 digits

Packaging Specifications Code

Resistance tolerance

Part No.

Code

E0AP

Packaging specifications

Paper tape (4mm Pitch)

Reel

φ180mm (7in.)

Basic ordering unit (pcs)

(

)

(

)

5 000

MNR12

Reel (

: Standard product

φ180) : JEITA ET-7200B

Rev.H

4/4

Appendix

Notes

No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM

CO.,LTD.

The content specified herein is subject to change for improvement without notice.

The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you

wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM

upon request.

Examples of application circuits, circuit constants and any other information contained herein illustrate the

standard usage and operations of the Products. The peripheral conditions must be taken into account when

designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specified in this document. However, should

you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no respon-

sibility for such damage.

The technical information specified herein is intended only to show the typical functions of and examples of

application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or

exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility

whatsoever for any dispute arising from the use of such technical information.

The Products specified in this document are intended to be used with general-use electronic equipment or

devices (such as audio visual equipment, office-automation equipment, communication devices, electronic

appliances and amusement devices).

The Products are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or

malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard against the

possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as

derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your

use of any Product outside of the prescribed scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or system

which requires an extremely high level of reliability the failure or malfunction of which may result in a direct

threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,

aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no

responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended

to be used for any such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specified herein that may be controlled under

the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

THE AMERICAS / EUROPE / ASIA / JAPAN

ROHM Customer Support System

www.rohm.com

TEL : +81-75-311-2121

FAX : +81-75-315-0172

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan

Appendix1-Rev3.0

MNR12E0APF2203 [ROHM]

相关型号：

MNR12E0APF221

MNR12E0APF223

MNR12E0APF224

MNR12E0APF240

MNR12E0APF241

MNR12E0APF242

MNR12E0APF243

MNR12E0APF270

MNR12E0APF2702

MNR12E0APF2703

MNR12E0APF271

MNR12E0APF273