MNR14E0ABJ221 [ROHM]
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 220ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP;型号: | MNR14E0ABJ221 |
厂家: | ROHM |
描述: | Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 220ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP 电阻器 |
文件: | 总6页 (文件大小:95K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MNR14
Resistors
Chip resistor networks
MNR14 (0603×4 size)
zFeatures
1) Convex electrodes
Easy to check the fillet after soldering is finished.
2) Small, light, rectangular 4-chip network
Area ratio is 65% smaller than that of MNR34, while weight ratio has been cut 75%.
3) High-density mounting
Can be mounted even more densely than four 0603 chips (MCR03), and mounting costs are lower.
4) Compatible with a wide range of mounting equipment.
Squared corners make it excellent for mounting using image recognition machines.
5) ROHM resistors have approved ISO-9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with
the product before using or ordering it.
zRatings
Item
Conditions
Specifications
0.063W (1 / 16W)
at 70°
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
C
100
80
60
40
20
0
−55
0
70
100 125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E= P×R
P: Rated power (W)
Limiting element voltage
50V
R: Nominal resistance (Ω)
Nominal resistance
See Table 1.
Operating temperature
−55°C to +125°C
Rev.A
1/5
MNR14
Resistors
Jumper type
Table 1
Resistance
Max. 50mΩ
1A
Resistance range
Resistance temperature coefficient
(ppm / °
Resistance tolerance
(Ω)
C)
Rated current
J
(
5%)
2.2≤R≤10
10≤R≤1M
(E6)
500
200
Operating temperature
−55°C to +125°C
(E24)
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
zCharacteristics
Guaranteed value
Item
Resistance
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistor type
J : 5%
Jumper type
Max. 50mΩ
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum Overload Voltage : 100V
Overload
(2.0%+0.1Ω)
Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
Max. 50mΩ
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
Rapid change of
temperature
Max. 100mΩ
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
Damp heat, steady state
(3.0%+0.1Ω)
Max. 100mΩ
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
(1.0%+0.05Ω)
Max. 100mΩ
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.25.3
125°C
Endurance
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
JIS C 5201-1 4.33
Bend strength of
the end face plating
Without mechanical damage such as breaks.
Rev.A
2/5
MNR14
Resistors
zExternal dimensions (Unit : mm)
3.2 0.1
a : 0.6 0.15
b : 0.4 0.15
a
b
∗
Marking
Material
B
Thick dielectric glaze of oxide metal
(only silver used for jumper)
1
A
A'
2
3
4
5
6
Thick film of silver for electrode
Nickel-coated electrode
External electrode coated with Sn
Alumina substrate
∗∗0.8
∗∗0.8
∗∗0.8
B'
6
2
3
4
Overcoating
1
Cross section A-A'
Cross section B-B'
5
6
1
∗
∗∗
Marking may change to the one-character type.
Pitch of the upper electrode.
5
zEquivalent circuit
R1
R2
R3
R4
R1=R2=R3=R4
zPackaging
Reel
Taping
P
0
φD0
P
2
P1
E
F
W
B
0
A
B
D
A
0
Heat crimp cover / Tape
Chip network
resistors
Thick paper (Underside paper tape)
mount
Square punchout hole
T2
C
Label
(Unit : mm)
EIAJ ET-7200B compliant
W
F
E
A0
B0
(Unit : mm)
D
8.0 0.3
3.5 0.05
1.75 0.1
1.8 0.1
3.4 0.1
A
B
C
D
0
P
0
P
1
P
2
T2
0
−3
+1
+1.0
φ180
φ13 0.2
φ60
9
0
0
+0.1
φ1.5
4.0 0.1
4.0 0.1
2.0 0.05
Max. 1.1
0
Rev.A
3/5
MNR14
Resistors
zProduct designation
M N R 1 4 E 0 A B J
Part No.
Resistance tolerance
Nominal resistance
Resistance code,3 digits,
000 denotes Jumper type.
J
5%
J is also used
for jumper
Packaging Specifications Code
Resistance tolerance
Part No.
Code
E0AB
Packaging specifications
Paper tape (4mm Pitch)
Reel
Basic ordering unit (pcs)
(
)
J
5%
,
MNR14
φ180mm (7in.)
5 000
Reel (φ180) : JEITA ET-7200B
: Standard product
zElectrical characteristics
400
300
6.0
6.0
4.0
JIS C 5201-1 4.8
SAMPLE SIZE : n=20pcs
25°C / −55°C 25°C / 125°C
JIS C 5201-1 4.13
JIS C 5201-1 4.5
SAMPLE SIZE : n=40pcs
20°C 65%RH
5.0
SAMPLE SIZE : n=20pcs
RATED VOLTAGE×2.5TIMES 2s
MAXIMUM OVERLOAD VOLTAGE : 100V
4.0
3.0
200
2.0
2.0
0
100
1.0
0
0
−1.0
−2.0
−3.0
−4.0
−5.0
−6.0
−100
−200
−300
−400
−2.0
−4.0
−6.0
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.2 Resistance
Fig.4 Overload
Fig.3 Variation resistance with
temperature
3.0
2.0
3.0
6.0
4.0
2.0
JIS C 5201-1 4.18
SAMPLE SIZE : n=20pcs
SOLDERING CONDITION
JIS C 5201-1 4.19
SAMPLE SIZE : n=20pcs
−55°C / 125°C 5cyc
JIS C 5201-1 4.24
SAMPLE SIZE : n=20pcs
40°C 93%RH WITH NO LOAD
1,000h
2.0
1.0
: 260°C 10S
1.0
0
0
0
−1.0
−2.0
−3.0
−2.0
−1.0
−2.0
−3.0
−4.0
−6.0
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.6 Rapid change of
temperature
Fig.5 Resistance to soldering heat
Fig.7 Damp heat, steady state
Rev.A
4/5
MNR14
Resistors
2.0
1.5
6.0
4.0
6.0
4.0
JIS C 5201-1 4.25.1
SAMPLE SIZE : n=20pcs
70°C 1,000h
OVERLOAD : THE RATED
VOLTAGE
JIS C 5201-1 4.29
SAMPLE SIZE : n=20pcs
IPA, 5min.
JIS C 5201-1 4.25.3
SAMPLE SIZE : n=20pcs
125°C WITH NO LOAD 1,000h
1.0
2.0
2.0
0.5
0
0
0
−0.5
−1.0
−1.5
−2.0
−2.0
−4.0
−6.0
−2.0
−4.0
−6.0
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
10
100
1k
10k 100k
1M
RESISTANCE (Ω)
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.9 Endurance
Fig.8 Endurance at 70°C
Fig.10 Resistance to solvents
Rev.A
5/5
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
相关型号:
MNR14E0ABJ241
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 240ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ271
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 270ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ273
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 27000ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ334
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 330000ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ361
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 360ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ362
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 3600ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ391
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 390ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ394
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 390000ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ471
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 470ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ472
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 4700ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
MNR14E0ABJ473
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 47000ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0612, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明