MNR18E0APJ203 [ROHM]

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.25W, 20000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0615, CHIP;


型号：	MNR18E0APJ203
厂家：	ROHM
描述：	Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.25W, 20000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0615, CHIP 电阻器
文件：	总4页 (文件大小：170K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Compact 8-element Chip Resistor Networks

MNR18 (06028 size)

Features

1) Suitable for damping resistors.

2) Convex electrodes

Easy to check the fillet after soldering is finished.

3) High-density mounting

Can be mounted even densely than eight 0402 chips (MCR01), and mounting costs are lower.

4) Compatible with a wide range of mounting machines.

Squared corners make it excellent for mounting using image recognition machines.

5) ROHM resistors have approved ISO9001- / ISO/TS16949- certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the

product before using or ordering it.

Ratings

Item

Conditions

Specifications

0.063W (1 / 16W)

Rated power

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

at 70°C

100

Power for a Packaging

Max 0.25W (1 / 4W)

−55

100 125

AMBIENT TEMPERATURE (

Fig.1

Rated voltage

The voltage rating is calculated by the following equation. If the value

obtained exceeds the limiting element voltage, the voltage rating

is equal to the maximum operating voltage.

E : Rated voltage (V)

P : Rated power (W)

R : Nominal resistance (Ω)

E = P × R

Limiting element voltage

25V

Nominal resistance

See Table 1.

Operating temperature

−55°C to +125°C

Table 1

Jumper type

Resistance

Resistance range

Resistance temperature coefficient

Max. 50mΩ

Resistance tolerance

5%)

(Ω)

(ppm / °C

)

(

≤

R≤1M

(E24)

200

Rated current

Power for a Packaging

Max 0.25W (1 / 4W)

∗Before using components in circuits where they will be exposed to transients such as pulse loads(short-duration, high-level loads),

be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be

guaranteed if it is used with a steady state voltage that is greater than its rated voltage.

Operating temperature −55°C to +125°C

www.rohm.com

2011.12 - Rev.G

1/3

Data Sheet

MNR18 (06028 size)

Characteristics

Guaranteed value

Jumper type

Max. 50mΩ

Item

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

J : 5%

Resistance

Max. 50mΩ

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Maximum Overload Voltage : 100V

Overload

(2.0%+0.1Ω)

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

Max. 100mΩ

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 100mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 100mΩ

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Dimensions (Unit : mm)

a : 0.3 0.1

b : (0.2)

(

) is reference value.

3.8 0.1

c : (0.5)

No.

Material

Resistive element (Oxide metal thick film)

Silver thick film electrode

Nickel electrode

Sn electrode

Alumina substrate

Overcoating (Resin)

Cross section A−A'

Cross section B−B'

Maqnification

www.rohm.com

2011.12 - Rev.G

2/3

Data Sheet

MNR18 (06028 size)

Inner circuit

R1 R2 R3 R4 R5 R6 R7 R8

R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8

Packaging

Reel

Taping

φD0

Heat crimp cover / Tape

(Underside paper tape)

Chip network

resistors

Thick paper

mount

Square punchout hole

Label

(Unit : mm)

EIAJ ET-7200B compliant

8.0 0.3

3.5 0.05

1.75 0.1

1.95 0.15

4.1 0.15

+0.1

4.0 0.1

2.0 0.05

Max. 1.1

φ1.5

Label

EIAJ ET-7200B (RRV) compliant

(Unit : mm)

−1.5

+1.0

φ180

φ13 0.2

φ60

Part No.Explanation

M N R 1 8 E 0 A P

Part No.

Resistance tolerance

Nominal resistance

Resistance code,3 digits,

000 denotes Jumper type.

J is also used

for jumper

Packaging Specifications Code

Resistance tolerance

Part No.

Code

E0AP

Packaging specifications

Paper tape (4mm Pitch)

Reel

φ180mm (7inch)

Basic ordering unit (pcs)

(

)

5 000

MNR18

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

www.rohm.com

2011.12 - Rev.G

3/3

Notice

N o t e s

No copying or reproduction of this document, in part or in whole, is permitted without the

consent of ROHM Co.,Ltd.

The content speciﬁed herein is subject to change for improvement without notice.

The content speciﬁed herein is for the purpose of introducing ROHM's products (hereinafter

"Products"). If you wish to use any such Product, please be sure to refer to the speciﬁcations,

which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein

illustrate the standard usage and operations of the Products. The peripheral conditions must

be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information speciﬁed in this document.

However, should you incur any damage arising from any inaccuracy or misprint of such

information, ROHM shall bear no responsibility for such damage.

The technical information speciﬁed herein is intended only to show the typical functions of and

examples of application circuits for the Products. ROHM does not grant you, explicitly or

implicitly, any license to use or exercise intellectual property or other rights held by ROHM and

other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the

use of such technical information.

The Products speciﬁed in this document are intended to be used with general-use electronic

equipment or devices (such as audio visual equipment, ofﬁce-automation equipment, commu-

nication devices, electronic appliances and amusement devices).

The Products speciﬁed in this document are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a

Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard

against the possibility of physical injury, ﬁre or any other damage caused in the event of the

failure of any Product, such as derating, redundancy, ﬁre control and fail-safe designs. ROHM

shall bear no responsibility whatsoever for your use of any Product outside of the prescribed

scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or

system which requires an extremely high level of reliability the failure or malfunction of which

may result in a direct threat to human life or create a risk of human injury (such as a medical

instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-

controller or other safety device). ROHM shall bear no responsibility in any way for use of any

of the Products for the above special purposes. If a Product is intended to be used for any

such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology speciﬁed herein that may

be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to

obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

www.rohm.com

R1120

MNR18E0APJ203 [ROHM]

相关型号：

MNR18E0APJ224

MNR18E0APJ242

MNR18E0APJ244

MNR18E0APJ271

MNR18E0APJ272

MNR18E0APJ273

MNR18E0APJ274

MNR18E0APJ300

MNR18E0APJ301

MNR18E0APJ302

MNR18E0APJ303

MNR18E0APJ304