MNR32M0ABJ181 [ROHM]

RES NET,THICK FILM,180 OHMS,200WV,5% +/-TOL,-200,200PPM TC,1012 CASE;


型号：	MNR32M0ABJ181
厂家：	ROHM
描述：	RES NET,THICK FILM,180 OHMS,200WV,5% +/-TOL,-200,200PPM TC,1012 CASE 电阻器
文件：	总5页 (文件大小：81K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MNR32

Resistors

Compact Chip Resistor Networks

MNR32 (1206×2 size)

zFeatures

1) Convex electrodes

Easy to check the fillet after soldering is finished.

2) Compatible with a wide range of mounting equipment.

Squared corners make it excellent for mounting using image recognition devices.

3) High-density mounting

Can be mounted even more densely than two 1206 chips (MCR18). Also, the number of parts and costs of mounting

have been reduced.

4) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with

the product before using or ordering it.

zRatings

Item

Conditions

Specifications

0.125W (1 / 8W)

Rated power

Power must be derated according to the power derating curve in

at 70°C

Figure 1 when ambient temperature exceeds 70°C.

100

−55

100 125

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

E= P×R

Limiting element voltage 200V

R: Nominal resistance (Ω)

Nominal resistance See Table 1.

Operating temperature

−55°C to 125°C

Rev.D

1/4

MNR32

Resistors

Jumper type

Table 1

Resistance range

Resistance temperature coefficient

Resistance

Max. 50mΩ

Resistance tolerance

J ( 5%)

(Ω)

(ppm / °C)

Rated current

(E24)

200

Operating temperature

−55°C to 125°C

•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

zCharacteristics

Guaranteed value

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

J : 5%

Jumper type

Max. 50mΩ

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Maximum Overload Voltage : 400V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

Max. 100mΩ

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 100mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 100mΩ

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Rev.D

2/4

MNR32

Resistors

zDimensions (Unit : mm)

2.6 0.2

∗

1.27

No.

Material

Cross section A-A'

Cross section B-B'

Resistive element

(Oxide metal thick film)

Silver thick film electrode

Nickel electrode

1 0 2

Sn electrode

Alumina substrate

Overcoating (Glass)

0.5 0.2

0.55 0.1

1.0 0.2

∗ Pitch of the upper electrode

zEquivalent circuit

R1=R2

zPackaging

Reel

Taping

(Unit : mm)

Label

1.75 0.1

EIAJ ET-7200B compliant

8.0 0.3

3.5 0.05

3.0 0.1

3.5 0.1

(Unit : mm)

+0.1

φ1.5

4.0 0.1

2.0 0.05

0.9 0.1

−1.5

+1.0

φ180

φ60

φ13 0.2

Rev.D

3/4

MNR32

Resistors

zPart No. Explanation

M N R 3 2 M 0 A B J

Part No.

Resistance tolerance

Nominal resistance

Resistance code,3 digits,

000 denotes Jumper type.

J is also used

for jumper

Packaging Specifications Code

Resistance tolerance

Part No.

Code

J0AB

Packaging specifications

Reel

φ180mm (7in.)

Basic ordering unit (pcs)

(

)

4 000

MNR32

Embossed tape (4mm Pitch)

Reel (

: Standard product

φ180) : JEITA ET-7200B

Rev.D

4/4

Appendix

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level

of reliability and the malfunction of which would directly endanger human life (such as medical

instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers

and other safety devices), please be sure to consult with our sales representative in advance.

It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance

of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow

for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in

order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM

cannot be held responsible for any damages arising from the use of the products under conditions out of the

range of the specifications or due to non-compliance with the NOTES specified in this catalog.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

THE AMERICAS / EUROPE / ASIA / JAPAN

ROHM Customer Support System

www.rohm.com

TEL : +81-75-311-2121

FAX : +81-75-315-0172

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan

Appendix1-Rev2.0

MNR32M0ABJ181 [ROHM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB