MVR22HXBRN473 [ROHM]
Trimmer, Metal Glaze/thick Film, 0.05W, 47000ohm, 30V, 25% +/-Tol, 1 Turn(s), 1108, CHIP;型号: | MVR22HXBRN473 |
厂家: | ROHM |
描述: | Trimmer, Metal Glaze/thick Film, 0.05W, 47000ohm, 30V, 25% +/-Tol, 1 Turn(s), 1108, CHIP |
文件: | 总6页 (文件大小:137K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MVR22
Resistors
Chip Trimmer Potentiometers
MVR22
zFeatures
1) Extremely small size and light weight facilitate the assembly of light, thinner, and smaller equipment.
2) Close match between wiper and resistive element reduces wiper noise.
3) Ruthenium oxide resistor material, with superb stability and resistance to humidity and the elements, offers the same
outstanding reliability of our existing product (MVR32).
4) Smoother and larger suction surface offers the same ease of mounting as that of the MVR32 chip.
5) Open design for reflow soldering.
6) Cross groove for easy adjustment.
7) Protective film prevents short circuits due to terminal contact.
8) The wiper is fully rotated during testing to guarantee its performance.
9) ROHM resistors have approved ISO9001- / ISO/TS 16494- certification.
zRatings
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the
product before using or ordering it.
Item
Conditions
Specifications
0.05W (1 / 20W) / element
at 70˚C
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70˚C.
100
80
60
40
20
0
– 55
0
70
100 125
155
AMBIENT TEMPERATURE ( ˚C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E : Rated voltage (V)
E = P × R
P : Rated power (W)
R : Nominal resistance (Ω)
Max. operating voltage
30V
Nominal total
resistance range
(recommended resistance value : E3 series)
(applicable resistance value : E6 series)
100 to 1MΩ
Total
25%
resistance tolerance
Resistance
variation
B (linear) characteristics
250 20˚
Effective rotation angle
Operating temperature
−55˚C to +125˚C
Reactive variable
range
within 10% (R>150Ω)
within 20% (R≤150Ω)
Rotational angle, both ends
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
•The remainder of flux may negatively affect product performance and reliability. So please make sure to wash and remove flux completely washing.
Rev.D
1/5
MVR22
Resistors
zCharacteristics
Characteristics
Specifications
Within 25%
3% or less
Test method (JIS C 5261)
DC total resistance
JIS C 5261 5.1
JIS C 5261 5.9
Contact
resistance rate
Resistance change
characteristics
B group OB
JIS C 5261 5.1
Voltage method
JIS C 5261 5.1
Residual resistance
R<1kΩ 20Ω or less
R≥1kΩ Within 2% of total nominal resistance
JIS C 5261 5.8 B method
Rotational speed of approx. 10 cycles per minute
(with one cycle defined as one round trip)
5% or less of total nominal resistance,
within the effective rotational range
Wiper noise
• Measurement circuit
Oscilloscope
Rx
Is
• Measurement waveform
Vn
Provided that the constant current has been set
according to the following:
10
Is : Is =
Rx
(When Rx ≤ 1kΩ,
constant current is defined as Is = 10mA)
Rx : Nominal resistance of semi-fixed test resistor.
Vn : Noise voltage
Vn
Is × Rx
× 100 (%)
Noise rate =
Resistance temperature
characteristics
JIS C 5261 5.3
+25 / −55 / +25 / +125˚
250ppm / ˚
C
C
Resistance to dry heat
Total resistance change rate : (5.0%+0.1Ω)
Constriction contact resistance rate: 8% or less
JIS C 5261 7.2
125˚C Test time : 1,000 to 1,048 hrs.
Temperature cycling
Total resistance change rate : (5.0%+0.1Ω)
Constriction contact resistance rate: 8% or less
JIS C 5261 7.3
Test temperature: −55˚C to + 125˚C 100cyc.
Resistance to humidity Total resistance change rate : (5.0%+0.1Ω)
JIS C 5261 7.4
60˚C , 95%RH
(steady state)
Constriction contact resistance rate: 8% or less
Test time: 1,000 to 1,048 hrs.
Endurance
(under load in damp
environment)
Total resistance change rate : (5.0%+0.1Ω)
Constriction contact resistance rate: 8% or less
JIS C 5261 7.6
Rated voltage (current) , 60˚
1.5h : ON −0.5h : OFF
Test time: 1,000 to 1,048 hrs.
C, 95%RH
Endurance
(steady state)
Total resistance change rate : (5.0%+0.1Ω)
Constriction contact resistance rate : 8% or less
JIS C 5261 7.7
Rated voltage (current) , 70˚
1.5h : ON −0.5h : OFF
Test time: 1,000 to 1,048 hrs.
C
Rotational torque
0.5 to 15.0mN
•
m
JIS C 5261 6.2
(5 to 150gf cm)
•
Endurance
(wiper)
Total resistance change rate : Within 15%
Constriction contact resistance rate : 8% or less
JIS C 5261 7.8
After 20 rotations
Rev.D
2/5
MVR22
Resistors
Characteristics
Specifications
Test method (JIS C 5261)
Terminal strength
(compression)
Total resistance change rate : (3.0%+0.1Ω)
There must be no mechanical damage.
JIS C 5261 6.5
Force (4.9N) is applied from three directions
upon the middle of the sides of the sample
on the surface being tested, as shown in the
illustration on the left.
Terminal strength
(flexural)
Total resistance change rate : (3.0%+0.1Ω)
There must be no mechanical damage.
JIS C 5261 6.5
Duration of pressure : 5 1s
Amount of bending : 3 mm
JIS C 5261 6.7
Soldering conditions : 260 5˚
Resistance to
soldering heat
Total resistance change rate : (3.0%+0.1Ω)
Constriction contact resistance rate : 5% or less
C
Soldering time : 10 1s.
Solderability
95% of terminal surface must be covered by
new soldering, and there must be no
soldering corrosion.
JIS C 5261 6.8
Flux : Rosin methanol or rosin isopropyl alcohol
Solder : H63A
Soldering conditions : 235 5˚
Soldering time : 2.0 0.5s.
C
zDimensions (Unit: mm)
A
Part
Material
Alumina, 96% or higher in content
Metal glaze type with RuO as the main component
F
T2
③
I
Substrate
G
B
⑥
J
Resistance paste
2nd Terminal (T2)
Wiper
2
①
Stainless steel and Ni plating + Au plating
Stainless steel
1st, 3rd Terminal (T1,T3) Ag/Pd/Pt thick film and soldering (Sn/Ag/Cu)
Protective film Organic film
④
②
L
K
T3
T1
⑤
(Unit : mm)
H
A
B
(C)
D
E
F
G
+0.15
2.0
0.9 0.1 (1.35 0.2) 1.35 0.2 2.7 0.15
2
0.1
N
1.35 +0.05
0.4+0.05
−0.05
0
0
I
J
K
L
M
O
P
0
1.45 0.06 0.64 −0.1 0.65 0.1 0.65 0.1 0.5 0.1 0.85 0.1 0.65 0.1 0.65 0.1
zEquivalent circuit
T
1
T3
T
2
T : terminal
Rev.D
3/5
MVR22
Resistors
zPackaging
Reel
Taping
P2
P0
A
D
B
P1
K
A0
C
Label
EIAJ ET-7200B compliant
(Unit : mm)
(Unit : mm)
D
W
F
E
A0
B0
A
B
C
8.0 0.2 3.5 0.05 1.75 0.1 2.25 0.1 3.0 0.1
0
+1
0
+1.0
0
D
0
P0
P
1
P
2
K
φ180
φ60
9
φ13 0.2
φ1.5 + 0.1
4.0 0.1 2.0 0.05 1.8 0.3
−1.5
4.0 0.1
0
zPart No. Explanation
Part No.
Packaging / Processing specifications
Resistance
tolerance
Nominal
resistance
Basic
ordering
unit(pcs)
3-digit IEC coding system
N
25%
Code
Part No.
MVR22
Soldering
Packaging specifications
Reel
Embossed tape
(4mm Pitch)
HXBR
Reflow soldering
φ180mm (7in)
2,000
Rev.D
4/5
MVR22
Resistors
zRecommended screwdriver for adjusting MVR resistors
Model
Open, type 2
MVR22
Dimensions, configuration Manual adjustment, automatic adjustment
Commercially sold product
(Maker)
No.9000(+) 0×30 [Vessel]
No.205 (+) No.0 [Vessel]
Rev.D
5/5
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
THE AMERICAS / EUROPE / ASIA / JAPAN
ROHM Customer Support System
Contact us : webmaster@ rohm.co.jp
www.rohm.com
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Copyright © 2008 ROHM CO.,LTD.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
Appendix1-Rev2.0
相关型号:
©2020 ICPDF网 联系我们和版权申明