PML10EZPJV [ROHM]

Ultra-low ohmic chip resistors for current detection;


型号：	PML10EZPJV
厂家：	ROHM
描述：	Ultra-low ohmic chip resistors for current detection
文件：	总8页 (文件大小：969K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Ultra-low ohmic chip resistors for current detection <Wide terminal type>

PML series

Datasheet

●

Features

1)Ultra low-ohmic resistance range.

2)Wide terminal configuration for high joint reliability.

3)Improved current detection accuracy by trimming-less structure.

4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.

●

Products List

Operating

temperature

range

Size

Rated power

Temperature

coefficient

Resistance

tolerance

Resistance range

(70℃)

Part No.

(mm)

2102

3216

(inch)

0805

1206

(W)

(ppm / ℃)

(%)

(mΩ)

(℃)

G( ±2%)

J ( ±5%)

G( ±2%)

J ( ±5%)

PML10

PML18

0.66

±200

1.0,1.5,2.0,2.5

-55 ～ +155

±150

0.5,1.0,1.5,2.0,2.5

-55 ～ +155

±150

±100

☆±200

0.5

2.2

PML50

5025

6432

2010

2512

J ( ±5%)

☆(1.0,1.5,2.0)

±150

±100

0.5

(3W at 25℃)

PML100

-55 ～ +155

1.0,1.5,2.0,2.2

☆:Under development

*Design and specifications are subject to change without notice.

Carefullycheck the specification sheetsupplied with the product before using or ordering it.

●

Part number description

P M L

1 0

E Z P

1 L 0

Part No.

Size (mm[inch])

Packaging specifications code

Nominal resistance

Resistance code,

3 or 4 digits.

Resistance

tolerance

Special

part code

10(2102[0805])

18(3216[1206])

50(5025[2010])

100(6432[2512])

Packaging

specifications

Quantity

PML

Part No. Code

/ Reel

(Ultra-low ohmic

chip resistors for

current detection

/ wide terminal

type>)

G( ±2%)

J ( ±5%)

Paper tape

(4mm pitch)

Resistance

PML10 EZP

PML18 EZP

PML50 HZP

PML100 HZP

5,000

Resistance

tolerance

value(Ω)

Paper tape

(4mm pitch)

5,000

2,000

0.5mΩ

1mΩ

1.5mΩ

2mΩ

2.2mΩ

2.5mΩ

0L5

1L0

1L5

2L0

2L2

2L5

0L50

1L00

1L50

2L00

Embossed tape

(4mm pitch)

Embossed tape

(4mm pitch)

2L50

www.rohm.com

1/4

2017.01 - Rev.D

PML series

Datasheet

●Chip resistor dimensions and markings

■PML 10 / 18

■PML 50 / 100

There are four digits used for the calculation number "L" is

used for the decimal point of m .

Ex.) 2mΩ = 2L00

10mΩ = 10L0

(Unit:mm)

Marking

Part No.

PML10

PML18

PML50

PML100

(mm)

2102

3216

5025

6432

(inch)

2102

3216

5025

6432

existence

1.20±0.15

1.60±0.15

2.60±0.20

3.20±0.25

2.0±0.15

3.20±0.15

5.00±0.20

6.40±0.25

0.42～ 0.28*±0.15

0.50～ 0.36*±0.15

0.45～ 0.35*±0.25

0.55～ 0.35*±0.20

0.75～ 0.70*±0.20

0.90～ 0.70*±0.25

Yes

0.40±0.20

0.45±0.25

* : Each value range varies with the resisrance. Please contact a ROHMsales representative for futher details.

●Land pattern example

(Unit:mm)

Dimensions

0.14

0.325

0.8

Part No.

PML10

1.6

2.0

3.2

5.0

6.4

0.73

1.175

1.275

1.7

PML18

PML50

PML100

2.675

3.35

4.2

0.8

www.rohm.com

2/4

2017.01 - Rev.D

PML series

Datasheet

●Derating curve

When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.

■PML10/18/50/100

●Characteristics (PML10/18/50/100)

Guaranteed >

Resistor type

Test items

Test conditions

20℃

Measuring method : Measure Bottom termination

by4 proves.

Resistance

See P.1

Variation of resistance

with temperature

See P.1

Measurement：+25/-55, +25/+125℃

Overload

±(2.0％＋0.0001Ω)

Rated power×2.5, 2s

Anew uniform coating of minimum

of 95%of the surface being

immersed and no soldering

damage.

Rosin-ethanol solution(25%weight)

Soldering condition：245±5℃

Duration of immersion：2.0±0.5s

Solderability

±(1.0％＋0.0001Ω)

Soldering condition：260±5℃

Resistance to

soldering heat

No remarkable abnormalityon the appearance. Duration of immersion：10±1s

Rapid change of

temperature

±(1.0％＋0.0001Ω)

±(3.0％＋0.0001Ω)

Test temp：-55℃～+125℃ 5cycle

40℃，93％(Relative humidity)

Test time：1,000h

Damp heat, steadystate

70℃,Rated power

1.5h:ON－0.5h:OFF

Test time：1,000h

Endurance at 70℃

±(3.0％＋0.0001Ω)

155℃

Test time：1,000h

Endurance

±(3.0％＋0.0001Ω)

±(0.5％＋0.0001Ω)

23±5℃ Immersion cleaning, 5±0.5min

Solvent: 2-propanol

Resistance to solvent

Bend strength of

the end face plating

Wihout open.

Compliance Standard(s) : IEC60115-8

JISC 5201-8

www.rohm.com

3/4

2017.01 - Rev.D

PML series

Datasheet

●Tape dimensions

■Paper tape

(Unit : mm)

Part No.

+0.2

-0.1

+0.1

+0.2

-0.1

+0.15

-0.05

PML10

8.0±0.3

3.5±0.05 1.75±0.1 1.65

3.5±0.05 1.75±0.1 1.95

2.4

PML18

8.0±0.3

3.5

-0.05

Part No.

+0.1

PML10 Φ1.5

PML18 Φ1.5

4.0±0.1

2.0±0.05 MAX1.1

4.0±0.1

(Unit : mm)

■Embossed tape

Part No.

PML50 12.0±0.3

PML100 12.0±0.3

5.5±0.05 1.75±0.1

2.9±0.2

5.3±0.2

6.7±0.2

3.5±0.2

Part No.

+0.1

PML50 Φ1.5

4.0±0.1

2.0±0.05 MAX1.1

PML100 Φ1.5

4.0±0.1

●Reel dimensions

(Unit : mm)

Part No.

PML10

PML18

PML50

PML100

+1.0

-1.5

+1.0

Φ180

Φ60

Φ13±0.2

www.rohm.com

4/4

2017.01 - Rev.D

Notice

Precaution on using ROHM Products

1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,

OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you

intend to use our Products in devices requiring extremely high reliability (such as medical equipment ^{(Note 1)}, transport

equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car

accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or

serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.

Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any

damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific

Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

USA

CHINA

CLASSⅢ

CLASSⅣ

CLASSⅡb

CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are designed and manufactured for use under standard conditions and not under any special or

extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any

special or extraordinary environments or conditions. If you intend to use our Products under any special or

extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of

product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in

the range that does not exceed the maximum junction temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Notice-PGA-E

Rev.003

Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

Precaution for Product Label

A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign

trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data.

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the

Products with other articles such as components, circuits, systems or external equipment (including software).

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM

will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to

manufacture or sell products containing the Products, subject to the terms and conditions herein.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

Notice-PGA-E

Rev.003

Daattaasshheeeett

General Precaution

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s

representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or

concerning such information.

Notice – WE

Rev.001

Datasheet

PML50HZPJV - Web Page

Part Number

Package

Unit Quantity

PML50HZPJV

2000

Minimum Package Quantity

Packing Type

Constitution Materials List

RoHS

2000

Taping

inquiry

Yes

PML10EZPJV [ROHM]

相关型号：

PML10EZPJV1L0

PML10EZPJV1L5

PML10EZPJV2L0

PML10EZPJV2L5

PML10_11

PML10_1111

PML12030A007V-000

PML12030A007V-001

PML12050A007V-000

PML12050A007V-001

PML18

PML18EZPGG