QS6K1FRA [ROHM]
车载MOSFET与通用品共用数据表。下订单时，请注意下列型号命名方式，编写为车载型号。;
| 型号： | QS6K1FRA |
| 厂家： | 
ROHM |
| 描述： | 车载MOSFET与通用品共用数据表。下订单时，请注意下列型号命名方式，编写为车载型号。 |
| 文件： | 总6页 (文件大小：1081K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
QS6K1FRA
Transistors
AEC-Q101 Qualified
2.5V Drive Nch+Nch MOS FET
QS6K1FRA
zStructure
zExternal dimensions (Unit : mm)
Silicon N-channel
MOS FET
TSMT6
1.0MAX
2.9
1.9
0.95 0.95
0.85
0.7
(6)
(5)
(4)
zFeatures
1) Low on-resistance.
0~0.1
(1)
(2)
(3)
2) Built-in G-S Protection Diode.
3) Small and Surface Mount Package (TSMT6).
1pin mark
0.16
0.4
Each lead has same dimensions
zApplication
Abbreviated symbol : K01
Power switching, DC / DC converter.
zEquivalent circuit
zPackaging specifications
(6)
(5)
(4) (6) (5) (4)
Package
Taping
TR
∗2
∗2
Type
Code
Basic ordering unit (pieces)
3000
QS6K1FRA
(1) (2) (3)
(1) Tr1 Gate
(2) Tr2 Source
∗1
∗1
(1)
(2)
(3)
(3) Tr2 Gate
(4) Tr2 Drain
(5) Tr1 Source
(6) Tr1 Drain
zAbsolute maximum ratings (Ta=25°C)
∗1 ESD PROTECTION DIODE
∗2 BODY DIODE
<It is the same ratings for the Tr1 and Tr2>
∗A protection diode is included between the gate and
the source terminals to protect the diode against static
electricity when the product is in use. Use the protection
circuit when the fixed voltages are exceeded.
Parameter
Drain-source voltage
Gate-source voltage
Symbol
VDSS
VGSS
ID
Limits
30
Unit
V
12
V
Continuous
Pulsed
1.0
A
Drain current
∗1
IDP
4.0
A
Source current
(Body diode)
Continuous
Pulsed
IS
0.8
A
∗1
∗2
ISP
4.0
A
1.25
0.9
W / TOTAL
Total power dissipation (TC=25°C)
PD
W / ELEMENT
Channel temperature
Storage temperature
∗1 Pw≤10µs, Duty cycle≤1%
∗2 Mounted on a ceramic board
Tch
150
°C
°C
Tstg
−55 to +150
zThermal resistance
Parameter
Symbol
Limits
Unit
100
139
°C / W / TOTAL
°C / W / ELEMENT
∗
Channel to ambient
Rth (ch-a)
∗ Mounted on a ceramic board
Rev.B
1/3
QS6K1FRA
Transistors
zElectrical characteristics (Ta=25°C)
<It is the same characteristics for the Tr1 and Tr2>
Parameter
Symbol Min. Typ. Max.
Conditions
µA VGS=12V, VDS=0V
ID=1mA, VGS=0V
µA VDS=30V, VGS=0V
Unit
Gate-source leakage
IGSS
−
−
−
10
−
Drain-source breakdown voltage V(BR) DSS 30
V
Zero gate voltage drain current
Gate threshold voltage
IDSS
−
0.5
−
−
−
−
−
1
VGS (th)
1.5
238
252
364
−
−
−
−
−
−
−
−
2.4
V
VDS=10V, ID=1mA
ID=1.0A, VGS=4.5V
170
180
260
−
77
25
15
7
Static drain-source on-state
resistance
∗
RDS (on)
mΩ ID=1.0A, VGS=4.0V
ID=1.0A, VGS=2.5V
∗
Forward transfer admittance
Input capacitance
Output capacitance
Reverse transfer capacitance
Turn-on delay time
Rise time
Yfs
Ciss
1.0
S
ID=1.0A, VDS=10V
VDS=10V
VGS=0V
f=1MHz
ID=500mA, VDD 15V
VGS=4.5V
−
−
−
−
−
−
−
−
pF
pF
pF
ns
ns
ns
ns
Coss
Crss
td (on)
∗
∗
∗
∗
∗
∗
∗
t
r
7
Turn-off delay time
Fall time
td (off)
tf
15
6
RL=30.0Ω
RG=10Ω
Total gate charge
Gate-source charge
Qg
1.7
0.4
0.4
nC VDD 15V
nC VGS=4.5V
nC ID=1.0A
Qgs
Qgd
−
−
−
−
Gate-drain charge
∗Pulsed
zBody diode characteristics (Source-Drain) (Ta=25°C)
<It is the same characteristics for the Tr1 and Tr2>
Parameter
Forward voltage
Symbol Min. Typ. Max.
Conditions
IS=3.2A, VGS=0V
Unit
∗
VSD
−
−
1.2
V
∗Pulsed
Rev.B
2/3
QS6K1FRA
Transistors
zElectrical characteristic curves
1000
100
10
8
7
6
5
4
3
2
1
0
1000
Ta=25°C
VDD=15V
VGS=4.5V
RG=10Ω
Pulsed
Ta=25°C
VDD=15V
ID=1A
RG=10Ω
Pulsed
Ta=25°C
f=1MHz
VGS=0V
t
f
100
Ciss
t
d (off)
d (on)
C
oss
rss
10
t
C
t
r
1
1
0.01
0.1
1
10
0
1
2
3
0.01
0.1
1
10
100
DRAIN CURRENT : ID (A)
TOTAL GATE CHARGE : Qg (nC)
DRAIN-SOURCE VOLTAGE : VDS (V)
Fig.2 Switching Characteristics
Fig.3 Dynamic Input Characteristics
Fig.1 Typical Capacitance
vs. Drain-Source Voltage
10
1
700
600
10
1
VDS=10V
Ta=25°C
VGS=0V
Pulsed
Pulsed
Pulsed
Ta=125°C
Ta=75°C
Ta=25°C
Ta= −25°C
500
400
300
200
100
0
Ta=125°C
Ta=75°C
Ta=25°C
Ta= −25°C
ID=1A
ID=0.5A
0.1
0.1
0.01
0.01
0.001
0.0
0.5
1.0
1.5
2.0
0
2
4
6
8
10
12
14
16
0.0
0.5
1.0
1.5
GATE-SOURCE VOLTAGE : VGS (V)
GATE-SOURCE VOLTAGE : VGS (V)
SOURCE-DRAIN VOLTAGE : VSD (V)
Fig.4 Typical Transfer Characteristics
Fig.5 Static Drain-Source
On-State Resistance vs.
Gate-Source Voltage
Fig.6 Source Current vs.
Source-Drain Voltage
10000
10000
1000
100
10000
1000
100
VGS=4.5V
Pulsed
VGS=4V
Pulsed
VGS=2.5V
Pulsed
Ta=125°C
Ta=75°C
Ta=25°C
Ta= −25°C
Ta=125°C
Ta=75°C
Ta=25°C
Ta= −25°C
Ta=125°C
Ta=75°C
Ta=25°C
Ta= −25°C
1000
100
0.01
0.1
1
10
0.01
0.1
1
10
0.01
0.1
1
10
DRAIN CURRENT : ID (A)
DRAIN CURRENT : ID (A)
DRAIN CURRENT : ID (A)
Fig.7 Static Drain-Source
On-State Resistance
vs. Drain Current (Ι)
Fig.8 Static Drain-Source
On-State Resistance
vs. Drain Current (ΙΙ)
Fig.9 Static Drain-Source
On-State Resistance
vs. Drain Current (ΙΙΙ)
Rev.B
3/3
Daattaasshheeeett
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号：
QS6M3TR
Small Signal Field-Effect Transistor, 1.5A I(D), 30V, 2-Element, N-Channel and P-Channel, Silicon, Metal-oxide Semiconductor FET, TSMT6, 6 PIN
ROHM
QS6M4TR
Small Signal Field-Effect Transistor, 1.5A I(D), 30V, 2-Element, N-Channel and P-Channel, Silicon, Metal-oxide Semiconductor FET, TSMT6, 6 PIN
ROHM
©2020 ICPDF网 联系我们和版权申明