SML-020MLTT86PN [ROHM]
Dual Color LED, Red/green, Transparent Clear, 2.3mm, 3 X 2.50 MM, 1.30 MM HEIGHT, SURFACE MOUNT PACKAGE-4;型号: | SML-020MLTT86PN |
厂家: | ROHM |
描述: | Dual Color LED, Red/green, Transparent Clear, 2.3mm, 3 X 2.50 MM, 1.30 MM HEIGHT, SURFACE MOUNT PACKAGE-4 光电 |
文件: | 总7页 (文件大小:219K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SURFACE MOUNT LED LAMPS
Dual-Color Type Chip LEDs with reflector
SML-020 Series
Green
Red
GaAIAs on GaAs
660nm
Package Size�
(mm)�
Part No.
GaP
570nm
3225
(
)
1210
SML-020MLT
○�
○�
3.0×2.5
t=1.3
Absolute Maximum Ratings(Ta=25℃)�
■
External Dimensions(Unit:mm)�
■
Peak�
3.0
2.3
1.3
0.5
Power� Forward�
dissipation current�
Reverse�Operating� Stotage�
voltage temperature temperature�
forward�
Emitting�
color
Part No.
current
�
PD
IF
VR
Topr
Tstg
*IFP
(mW)�(mA)�
(V)� (°C)�
(°C)�
(mA)�
Red
Green
Green
Red
25
60
75
4
SML-020MLT
-30 to +85
-40 to +85
60
30
Cathode mark
*IFP measured under duty ≦1/ 5,pulse width ≦1ms.
Electrical Optical Characteristics(Ta=25℃)�
■
Green
Red
1
3
2
4
1
2
Light wavelength
Brightness�
Forward� Reverse�
IV
voltage�
current�
Peak Half-wave
Part No.
Resin Color
VF
IR
4
3
λp
∆λ
1.0
Terminal
Typ.
( )
V
IF
mA
Max.
VR
( )
V
Typ. Typ.
IF
Min. Typ.
mcd mcd
IF
mA
(
)
(µ )
(
)
(
)
(
)
(
)
(
)
(
)
A
nm
nm
40
25
mA
Tolerance:±0.1
2.2
570
660
20
SML-020MLT Transparent Clear
20
100
4
20
9.0
16
20
1.75
Directivity
■
Green
Red
0°
X’
Y’
30°
30°
60°
60°
90°
100
90°
100
50
0
50
(
)
%
Relative brightness
(
)
Typ.
Recommemded Pad Layout
Packaging Spacifications(Unit:mm)�
■
■
Tape Spacifications:T86〈2,500pcs/reel〉
Reel Spacifications
1.05 0.6 1.05
Feeding direction
4
φ1.5
2
φ1 3
2.9
1.6
(Unit:mm)�
φ6 0
The recommended thickness of the screen mask
for soldering is between 100 and 200μm. The
hole size of the screen mask should be same as
the recommended land pattern or smaller.
φ180
SURFACE MOUNT LED LAMPS
Electrical Characteristic Curves
■
Forward Current - Forward Voltage
Relative Luminous Intensity - Case Temperature
50
1.6
SML-020MLT<Green>�
SML-020MLT<Red>
SML-020MLT<Green>�
SML-020MLT<Red>
Ta=25℃�
IF=20mA
20
10
1.4
1.2
1.0
0.8
5.0
2.0
1.0
0.5
0.6
0.4
0.2
0.1
1.5
2.0
2.5
3.0
60
80
-20
0
20
40
FORWARD VOLTAGE : VF (V)
CASE TEMPERATURE : Tc (℃)
Relative Luminous Intensity - Forward Current
3.0
3.0
2.5
2.0
1.5
1.0
SML-020MLT<Green>�
SML-020MLT<Red>
f=1kHz
f=1kHz
DC
2.5
DC
2.0
DF=50%
20%
1.5
1.0
DF=50%
20%
15%
15%
10%
5%
0.5
0
0.5
0
10%
5%
0
10
20
30
40
50
60
0
10
20
30
40
50
60
PEAK FORWARD CURRENT : IF peak (mA)
PEAK FORWARD CURRENT : IF peak (mA)
Ratio of Maximum Tolerable Peak Current - Pulse Duration
6
5
6
5
SML-020MLT<Green>�
SML-020MLT<Red>
4
4
3
3
2.4
2.5
2
2
1
1
10 20 50 102
PULSE DURATION : Tw (μs)
103
104
5
10 20 50 102
103
104
5
PULSE DURATION : Tw (μs)
Derating
SML-020MLT<Green>�
SML-020MLT<Red>
30
20
�
�
10
�
0
0
10 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE : Ta (℃)
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
LED lamps
Table of luminosity rankings
Table of luminosity rankings
25
LED lamps
Table of intensity rankings
Luminous intensity rankings
(Units : mcd)
(Units : mcd)
FFor more information about rankings, contact your ROHM representative.
26
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document use silicon as a basic material.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.0
LED lamps
LED lamps
(8) Variation of luminous intensity depending on ambi-
ent temperature
ROHM LED lights have a temperature coefficient of
approximately –1% for red and orange, and * 0.5% for
yellow and green. (Refer to the luminous intensity vs.
case temperature characteristics for each LED type.)
FStorage precautions
Storage in a dry box is best. However, if this is not pos-
sible we recommend the following conditions :
Temperature : 5 to 30_C
Humidity : 60%RH max.
FRecommended PCB
We recommend the following hole diameters. Note, how-
ever, thatthesemayvarydependingontheboardmateri-
al, degree of integration, and wiring.
Determine the pulse drive conditions as follows.
1. Decide what repetition frequency (f) and duty factor
(DF) will be used.
2. Determine the maximum tolerable peak current ratio
from Figure 2.
IF peak Max.
IF Max.
3. Determine the maximum forward current from
Figure 3.
For example, when Ta = 40_C or above, the maximum
forward current (IF Max.) decreases.
4. Calculate the maximum tolerable peak current (IF
peak Max.).
FLED lamp product names
The product names of ROHM LED lamps and chip LEDs
are coded as follows :
Example
Iff=1kHz, DF=10%, andTa=40_C, themaximumtoler-
ablepeakcurrentratiofromFigure2is3.0forred, orange
and yellow, and 2.4 for green.
The maximum forward current IF Max. at Ta = 40_C is 20
mA for red, orange and yellow, and 25 mA for green.
Therefore, the maximum tolerable peak current under
these conditions is as follows :
FRed, orange and yellow . . 20 mA 3.0 = 60 mA
FGreen . . . . . . . . . . . . . . . . . . 25 mA 2.4 = 60 mA
For the repetition frequency, we recommend 1 kHz or
above.
(7) Decrease of rated current
The maximum rated forward current of LED lamps will
vary depending on the ambient operating temperature.
(Refer to Figure 3)
21
相关型号:
©2020 ICPDF网 联系我们和版权申明