SML-812MTT86 [ROHM]
Reverse-mount available type;型号: | SML-812MTT86 |
厂家: | ROHM |
描述: | Reverse-mount available type |
文件: | 总12页 (文件大小:1540K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SML-81 Series
Data Sheet
lFeatures
• Reverse-mount available type
lOutline
lSize
Color
Type
V
U
B
D
3412 (1305)
3.4×1.25mm (t=1.1mm)
W
M
WB
lDimensions
lRecommended Solder Pattern
(unit : mm)
(note) Tolerance is within 0.1mm
unless otherwise specified
xcept burr on terminal from consideration.
(unit : mm)
lSpecifications
Absolute Maximum Ratings (Ta=25ºC)
Electrical and Optical Characteristics (Ta=25ºC)
Emitting
Color
Peak Forward
Power
Forward Voltag VF Reverse Current IR
Luminous Intensity IV
Forward
Reverse
Current
Voltage
Dominant Wavelength lD
IF
Min. Typ.
Chip
Structure
Operating Temp.
Topr(ºC)
Part No.
Storage Temp.
Tstg(ºC)
Min.*3
Max.*3
Dissipation
Current
IF
VR
IF
Typ.
Max.
Typ.
PD(mW) IF(mA) IFP(mA) VR(V)
(V) (mA) (mA) (V) (nm) (nm) (nm) (mA) (mcd) (mcd) (mA)
SML-811VT(A)
SML-811UT(A)
SML-811DT(A)
SML-811WT(A)
SML-812MT
625 630 636
Red
11.2 22.4
615 620 625
602 605 608
587 590 593
569 572 575
464 470 476
(0.30, 0.30)
100*2
62
5
-40 to +85 -40 to +100 1.95 10
5
10
10
Orange
Yellow
AIGaInP
InGaN
25
100
10
14
14
22
22
28
40
56
45
Yellowish
Green
60*1
100*2
50*2
2.1
4
5
65
80
33
4
5
-30 to +85 -40 to +85
20
20
5
20
5
Blue
20
10
-30 to +85 -40 to +85
SML812BCT
3.3
White
SML813WBC8W
-40 to +85 -40 to +100
2.9
5
*1:Duty1/5, 200Hz *2:Duty1/10, 1kHz *3:Reference
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
1/11
Data Sheet
SML-81 Series
lElectrical Characteristics Curves
Fig.2 Luminous Intensity -
Atmosphere Temperature
Fig.1 Forward Current - Forward Voltages
100
1.6
SML-811VT(A)
Ta=25ºC
IF=10mA
IF=20mA
SML-811UT(A)
SML-811DT(A)
SML-811WT(A)
SML-812MT
1.4
1.2
1
10
0.8
SML-811VT(A)
SML-811UT(A)
SML-811DT(A)
SML-811WT(A)
SML-812MT
ꢀ
0.6
0.4
1
1.4
1.6
1.8
2.0
2.2
2.4
-40-30-20-10 0 10 20 30 40 50 60 70 80 90100
ATMOSPHERE TEMPERATURE : Ta [ºC]
FORWARD VOLTAGE : VF [V]
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
2.5
30
SML-811VT(A)
SML-811UT(A)
Ta=25ºC
SML-811DT(A)
SML-811WT(A)
SML-812MT
2.0
20
10
0
1.5
1.0
0.5
0.0
SML-811VT(A)
SML-811UT(A)
SML-811DT(A)
SML-811WT(A)
SML-812MT
0
5
10
15
20
25
-40 -20
0
20
40
60
80 100
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
2/11
Data Sheet
SML-81 Series
lElectrical Characteristics Curves
Fig.2 Luminous Intensity -
Atmosphere Temperature
Fig.1 Forward Current - Forward Voltages
1.4
100
SML812BC7T
Ta=25ºC
IF=20mA
1.2
1
10
0.8
ꢀ
SML812BC7T
1
0.6
2.2
2.6
3.0
3.4
3.8
-40 -20
0
20
40
60
80 100
FORWARD VOLTAGE : VF [V]
ATMOSPHERE TEMPERATURE : Ta [ºC]
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
1.2
25
SML812BC7T
SML812BC7T
Ta=25ºC
1.0
0.8
0.6
0.4
0.2
0.0
20
15
10
5
0
0
4
8
12
16
20
-40 -20
0
20
40
60
80 100
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
*The value is based on the die destruction endurance;
optical characteristics are NOT considered..
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
3/11
Data Sheet
SML-81 Series
lElectrical Characteristics Curves
Fig.2 Luminous Intensity -
Atmosphere Temperature
Fig.1 Forward Current - Forward Voltages
100
1.4
SML813WBC8W
Ta=25ºC
IF=5mA
1.2
1
10
0.8
ꢀ
SML813WBC8W
0.6
1
-40 -20
0
20
40
60
80 100
2.2
2.6
3.0
3.4
3.8
FORWARD VOLTAGE : VF [V]
ATMOSPHERE TEMPERATURE : Ta [ºC]
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
2.0
14
SML813WBC8W
SML813WBC8W
Ta=25ºC
12
10
8
1.5
1.0
0.5
0.0
6
4
2
0
-40 -20
0
20
40
60
80 100
0
2
4
6
8
10
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
*The value is based on the die destruction endurance;
optical characteristics are NOT considered..
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
4/11
Data Sheet
SML-81 Series
lViewing Angle
SML-81 series
SML-81 series
RELATIVE INTENSITY
RELATIVE INTENSITY
SML812BCT
SML813WBC8W
SML812BCT
SML813WBC8W
SCANNING ANGLE (deg)
RELATIVE INTENSITY
RELATIVE INTENSITY
lRank Reference of Brightness
Red(V,U)
(Ta=25ºC, IF=10mA)
AW AX
Rank
AG
AH
AJ
AK
AL
AM
AN
AP
AQ
AR
AS
AT
AU
AV
Iv (mcd)
9.0 to 11.2 11.2 to 14 14 to 18 18 to 22.4 22.4 to 28 28 to 35.5 35.5 to 45 45 to 56
56 to 71
71 to 90 90 to 112 112 to 140 140 to 180 180 to 224 224 to 280 280 to 355
SML-811VT(A)*
SML-811UT(A)*
Orange(D)
(Ta=25ºC, IF=10mA)
Rank
AG
AH
AJ
AK
AL
AM
AN
AP
AQ
AR
AS
AT
AU
AV
AW
AX
Iv (mcd)
9.0 to 11.2 11.2 to 14 14 to 18 18 to 22.4 22.4 to 28 28 to 35.5 35.5 to 45 45 to 56
56 to 71
71 to 90 90 to 112 112 to 140 140 to 180 180 to 224 224 to 280 280 to 355
SML-811DT(A)*
Yellow(Y)
(Ta=25ºC, IF=10mA)
Rank
AG
AH
AJ
AK
AL
AM
AN
AP
AQ
AR
AS
AT
AU
AV
AW
AX
Iv (mcd)
9.0 to 11.2 11.2 to 14 14 to 18 18 to 22.4 22.4 to 28 28 to 35.5 35.5 to 45 45 to 56
56 to 71
71 to 90 90 to 112 112 to 140 140 to 180 180 to 224 224 to 280 280 to 355
SML-811WT(A)*
Green(M)
(Ta=25ºC, IF=20mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
630 to 1000 1000 to 1600
40 to 63 63 to 100 100 to 160 160 to 250 250 to 400 400 to 630
Iv (mcd)
1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16
16 to 25
25 to 40
SML-812MT※
Blue(B)
(Ta=25ºC, IF=20mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
900 to 1400
56 to 90 90 to 140 140 to 220 220 to 360 360 to 560 560 to 900
Iv (mcd)
0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9
9 to 14
14 to 22
22 to 36
36 to 56
SML812BCT
White(WB)
(Ta=25ºC, IF=5mA)
Rank
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
900 to 1400
56 to 90 90 to 140 140 to 220 220 to 360 360 to 560 560 to 900
Iv (mcd)
0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9
9 to 14
14 to 22
22 to 36
36 to 56
SML813WBC8W
*Please note that the brightness of some products may fall between ranks (half rank).
※Brightness on specification sheet include tolerance of within ±10%.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
5/11
Data Sheet
SML-81 Series
lSpectrum Data
SML-811VT(A)
SML-811UT(A)
SML-811DT(A)
SML-811WT(A)
IF=20mA
IF=10mA
1.0
0.8
0.6
0.4
0.2
0.0
1.0
0.8
0.6
0.4
0.2
SML812BCT
SML-812MT
ꢀ
0.0
380
480
580
680
780
380
480
580
680
780
WAVELENGTH [nm]
WAVELENGTH [nm]
* Please take this data as a reference data for the samples are measured randomly.
* The data is relativized for each color. It is NOT to show the spectrum peaks are equal.
ꢀ
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
6/11
Data Sheet
SML-81 Series
lChromaticity Diagram
[Chromaticity Coordimates] (Ta=25ºC, IF=5mA)
A
F
H
K
x
y
x
y
x
y
x
y
0.280 0.248 0.283 0.305 0.287 0.295 0.304 0.330
0.296 0.276 0.304 0.330 0.307 0.315 0.330 0.360
0.283 0.305 0.307 0.315 0.311 0.294 0.330 0.318
0.264 0.267 0.287 0.295 0.296 0.276 0.311 0.294
K
F
H
Measurement tolerance : 0.02
A
CIE x
lTaping [T86 / 1(white)]
4±0.1
2±0.05
Cathode Index
+0.1
0
φ1.5
+0.1
-0.03
1.2
1.5±0.1
±1
11.4
Packing quantity
3000pcs/reel
(note) Tolerance is within 0.2mm unless otherwise specified
(Unit:mm)
Pull
direction
(
):Reference
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
7/11
Data Sheet
SML-81 Series
lPart No. Construction
lPacking Specification
ROHM LED products are being shipped with desiccant (silica gel) concluded in moisture-proof bags.
Pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card
inside the bag is available upon request.
Please contact the nearest sales office or distributer if necessary.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
2014.11 - Rev.G
8/11
SML-81 Series
Precaution (Surface Mount Device)
Data Sheet
l
1.Storage
If the product is heated during the reflow under the condition of hygroscopic state, it may vaporize and expand
which will influence the performance of the product. Therefore, the package is waterproof. Please use the
product following the conditions:
• Using Conditions
Classification
Temperature
Humidity
Expiration Date
Remark
Within 1 year
from Receiving
1
Before using
5 to 30ºC
30 to 70%RH
Storage with waterproof package
2
After opening
package
Please storing in the airtight container with
our desiccant (silica gel)
5 to 30ºC
Below 70%RH
Within168h
• Baking
Bake the product in case of below:
1
The expiration date is passed.
2
The color of indicator (silica gel) turned from blue to colorless or from green to pink.
(Even if the product is within the expiration date.)
• Baking Conditions
Temperature
Time
Humidity
60±3ºC
12 to 24h
Below 20%RH
• Bake products in reel.
• Reel and embossed tape are easy to be deformed when baking, so please try not to
apply stress on it.
Remark
• Recommend bake once.
2.Application Methods
2-1. Precaution for Drive System and Off Mode
Design the circuit without the electric load exceeding the ABSOLUTE MAXIMUM RATING that applies on the
products. If drive by constant voltage, it may cause current deviation of the LED and result in deviation of
luminous intensity, so we recommend to drive by constant current. (Deviation of VF Value will cause deviation of
current in LED.) Furthermore, for off mode, please do not apply voltage neither forward nor reverse. Especially,
for the products with the Ag-paste used in the die bonding, there’s high possibility to cause electro migration and
result in function failure.
2-2. Operation Life Span
There’s possibility for intensity of light drop according to working conditions and environments (applied current,
surrounding temperature and humidity, corrosive gases), please call our Sales staffs for inquiries about the
concerned application below.
1
Longtime intensity of light life
2
On mode all the time
2-3.Applied Stress on Product
The top of the LED is very soft, which the silicon resin is used as sealing resin. Therefore, please pay attention
to the overstress on it which may influence its reliability.
2-4.Usage
The Product is LED. We are not responsible for the usage as the diode such as Protection Chip, Rectifier,
Switching and so on.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
9/11
2014.11 - Rev.G
SML-81 Series
Data Sheet
3. Others
3-1. Surrounding Gas
Notice that if it is stored under the condition of acid gas (chlorine gas, sulfured gas) or alkali gas (ammonia), it
may result in low soldering ability (caused by the change in quality of the plating surface ) or optical
characteristics changes (light intensity, chrominance) and change in quality of die bonding (Ag-paste) materials.
All of the above will cause function failure of the products.
Therefore, please pay attention to the storage environment for mounted product (concern the generated gas of
the surrounding parts of the products and the atmospheric environment).
3-2. Electrostatic Damage
The product is part of semiconductor and electrostatic sensitive, there’s high possibility to be damaged by the
electrostatic discharge. Please take appropriate measures to avoid the static electricity from human body and
earthing of production equipment. The resistance values of electrostatic discharge (actual values) vary with
products, therefore, please call our Sales staffs for inquiries.
3-3. Electromagnetic Wave
Please concern the influence on LED in case of application with strong electromagnetic wave such as IH
(Induction heating).
4.Mounting
4-1. Soldering
• No resin hardening agent such as filler is used in the sealing resin of the product. Therefore, resin expansion
and moisture absorption at humidity will cause heat stress during soldering process and finally has bad
influence on the product’s reliability.
• The product is not for flow soldering.
• Do not expose the product in the environment of high temperature (over 100ºC) or rapid temperature shift
(within 3ºC of temperature gradient) during the flow soldering of surrounding parts.
• Please set appropriate reflow temperature based on our product usage conditions and specification.
• The max for reflowing is 2 times, please finish the second flow soldering and flow soldering with other parts
within the usage limitation after open the moistureproof package.
• Compare with N2 reflow, during air reflow, because of the heat and surrounding conditions, it may cause the
discoloration of the resin.
• For our product that has no solder resist, because of its solder amount and soldering conditions, one of its
specific characteristics is that solder will penetrate into LED. Thus, there's high possibility that will influence its
reliability. Therefore, please be informed, concerning it before using it.
4-2. Automatic Mounting
4-2-1.Silicon Resin Sealing Product
The sealing resin of LED is very soft, so please select adsorption nozzle that would not apply stress directly
on the sealing section.
4-2-2.Mini Package (Smaller than 1608 size)
Vibration may result in low mounting rate since it will cause the static electricity of product and adhere to top
cover tape. We recommend to
• set magnet on parts feeder cassette of the mounter to control the product stabilization
• set ionizer to prevent electrostatic charge
4-3. Mounting Location
The stress like bending stress of circuit board dividing after mounting, may cause LED package crack or
damage of LED internal junction, therefore, please concern the mounting direction and position to avoid bending
or screwing with great stress of the circuit board.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
10/11
2014.11 - Rev.G
SML-81 Series
Data Sheet
4-4. Mechanical Stress after Mounting
The mechanical stress may damage the LED after Circuit Mounting, so please pay attention to the touch on
product.
Stress strength according to
the mounting position:
A>B>C>D
4-5. Soldering Pattern for Recommendation
We recommend the soldering pattern that shows on the right. It will be
different according to mounting situation of circuit board, herefore, please
φ2.4
concern before designing.
Hole
1.25
The product has adopted the electrode structure that it should solder with
back electrode of the product. Thus, please be informed that the shape of
electrode pin of solder fillet formation is not guaranteed.
*
+
4.2
(Fig-1)
(
4-6. Reflow Profile
For reflow profile, please refer to the conditions below:( )
*
• Meaning of marks, Conditions
Mark
Meanings
Conditions
180ºC
Tsmax Maximum of pre-heating temperature
Tsmin Minimum of pre-heating temperature
140ºC
Ts
TL
Time from Tsmin to Tsmax
Reference temperature
Retention time for TL
Over 60sec.
230 to 260ºC
Within 40sec.
260ºC(Max)
Within 10sec.
Under 3ºC/sec.
Over -3ºC/sec.
tL
TP
Peak temperature
tP
Time for peak temperature
Temperature rising rate
Temperature decreasing rate
ΔTR/Δt
ΔTD/Δt
Above conditions are for reference. Therefore, evaluate by customer’s own circuit boards and reflow furnaces
before using, because stress from circuit boards and temperature variations of reflow furnaces vary by
customer’s own conditions.
*
4-7. Cleaning after Soldering
Please follow the conditions below if the cleaning is necessary after soldering.
Solvent
We recommend to use alcohols solvent such as, isopropyl alcohols
Temperature
Ultrasonic Cleaning
Drying
Under 30ºC within 3 minutes
15W / Below 1 liter (capacity of tank)
Under 100ºC within 3 minutes
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
11/11
2014.11 - Rev.G
Notice
N o t e s
1) The information contained herein is subject to change without notice.
2) Before you use our Products, please contact our sales representative and verify the latest specifica-
tions :
3) Although ROHM is continuously working to improve product reliability and quality, semicon-
ductors can break down and malfunction due to various factors.
Therefore, in order to prevent personal injury or fire arising from failure, please take safety
measures such as complying with the derating characteristics, implementing redundant and
fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no
responsibility for any damages arising out of the use of our Poducts beyond the rating specified by
ROHM.
4) Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral
conditions must be taken into account when designing circuits for mass production.
5) The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly,
any license to use or exercise intellectual property or other rights held by ROHM or any other
parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of
such technical information.
6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communi-
cation, consumer systems, gaming/entertainment sets) as well as the applications indicated in
this document.
7) The Products specified in this document are not designed to be radiation tolerant.
8) For use of our Products in applications requiring a high degree of reliability (as exemplified
below), please contact and consult with a ROHM representative : transportation equipment (i.e.
cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety
equipment, medical systems, servers, solar cells, and power transmission systems.
9) Do not use our Products in applications requiring extremely high reliability, such as aerospace
equipment, nuclear power control systems, and submarine repeaters.
10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with
the recommended usage conditions and specifications contained herein.
11) ROHM has used reasonable care to ensur the accuracy of the information contained in this
document. However, ROHM does not warrants that such information is error-free, and ROHM
shall have no responsibility for any damages arising from any inaccuracy or misprint of such
information.
12) Please use the Products in accordance with any applicable environmental laws and regulations,
such as the RoHS Directive. For more details, including RoHS compatibility, please contact a
ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting
non-compliance with any applicable laws or regulations.
13) When providing our Products and technologies contained in this document to other countries,
you must abide by the procedures and provisions stipulated in all applicable export laws and
regulations, including without limitation the US Export Administration Regulations and the Foreign
Exchange and Foreign Trade Act.
14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of
ROHM.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
R1102
A
相关型号:
©2020 ICPDF网 联系我们和版权申明