SML-D12P8WT86K [ROHM]
Single Color LED, Green, Milky White, 1.2mm, 1.60 X 0.80 MM, 0.55 MM HEIGHT, 0603, 2 PIN;
| 型号： | SML-D12P8WT86K |
| 厂家： | 
ROHM |
| 描述： | Single Color LED, Green, Milky White, 1.2mm, 1.60 X 0.80 MM, 0.55 MM HEIGHT, 0603, 2 PIN 光电 |
| 文件： | 总9页 (文件大小：688K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SML-D1 series
EXCELEDTM
Datasheet
Features
• EXCELEDTM series
• Original device technology enables high brightness
and high reliability
Size
Color
V
U
P
Type
1608 (0603)
1.6×0.8mm (t=0.55mm)
Y
M
Dimensions
Recommended Solder Pattern
Tolerance : 0.1
(unit : mm)
(unit : mm)
Specifications
Absolute Maximum Ratings (Ta=25ºC)
Electrical and Optical Characteristics (Ta=25ºC)
Emitting
Color
Peak Forward
Power
Forward Voltag VF Reverse Current IR
Luminous Intensity IV
Forward
Reverse
Current
Voltage
Dominant Wavelength D
IF
(V) (mA) (A) (V) (nm) (nm) (nm) (mA) (mcd) (mcd) (mA)
Chip
Structure
Operating Temp.
Topr(ºC)
Part No.
Storage Temp.
Tstg(ºC)
Min.*2
Max.*2
Dissipation
Current
IF
VR
IF
Typ.
Max.
Typ.
Min. Typ.
PD(mW) IF(mA) IFP(mA) VR(V)
SML-D12V8W
SML-D12U8W
SML-D12D8W
SML-D12Y8W
SML-D12M8W
SML-D12P8W
SML-D13U8W
SML-D13Y8W
SML-D13M8W
625 630 635
615 620 625
602 605 608
587 590 593
569 572 575
557 560 563
615 620 625
587 590 593
568 572 574
16
25
40
63
Red
Orange
Yellow
40 100
54
2.2
4
25
10
63
25
AIGaInP
on GaAs
Yellowish
Green
100*1
20
5
40 to 85 40 to 100
20
10
20
20
Green
Red
2.5 6.3
40 70
63 100
16 30
52
54
2.1
2.2
Yellow
5
4
Yellowish
Green
*1:Duty1/10, 1kHz *2:Reference
EXCELEDTM is ROHM's pending trademark.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
1/8
Data Sheet
SML-D1 series
Electrical Characteristics Curves
Fig.2 Luminous Intensity -
Atmosphere Temperature
Fig.1 Forward Current - Forward Voltages
100
1.6
SML-D12V8W
SML-D12U8W
SML-D12D8W
SML-D12Y8W
SML-D12M8W
SML-D12P8W
Ta=25ºC
IF=20mA
1.4
1.2
1
10
0.8
SML-D12V8W
SML-D12U8W
SML-D12D8W
SML-D12Y8W
SML-D12M8W
SML-D12P8W
ꢀ
0.6
0.4
1
1.5
2.0
FORWARD VOLTAGE : VF [V]
2.5
-40 -20
0
20
40
60
80 100
ATMOSPHERE TEMPERATURE : Ta [ºC]
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
1.2
30
SML-D12V8W
Ta=25ºC
SML-D12U8W
SML-D12D8W
SML-D12Y8W
1.0
SML-D12M8W
SML-D12P8W
0.8
0.6
0.4
0.2
0.0
20
10
0
SML-D12V8W
SML-D12U8W
SML-D12D8W
SML-D12Y8W
SML-D12M8W
SML-D12P8W
-40 -20
0
20
40
60
80 100
0
4
8
12
16
20
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
2/8
Data Sheet
SML-D1 series
Electrical Characteristics Curves
Fig.2 Luminous Intensity -
Atmosphere Temperature
Fig.1 Forward Current - Forward Voltages
100
1.6
SML-D13U8W
SML-D13Y8W
SML-D13M8W
Ta=25ºC
IF=20mA
1.4
1.2
1
10
0.8
ꢀ
0.6
0.4
SML-D13U8W
SML-D13Y8W
SML-D13M8W
1
1.5
2.0
FORWARD VOLTAGE : VF [V]
2.5
-40 -20
0
20
40
60
80 100
ATMOSPHERE TEMPERATURE : Ta [ºC]
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
30
20
10
0
1.2
SML-D13U8W
SML-D13Y8W
SML-D13M8W
SML-D13U8W
SML-D13Y8W
SML-D13M8W
Ta=25ºC
1.0
0.8
0.6
0.4
0.2
0.0
0
4
8
12
16
20
-40 -20
0
20
40
60
80 100
FORWARD CURRENT : IF [mA]
AMBIENT TEMPERATURE : Ta [ºC]
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
3/8
Data Sheet
SML-D1 series
Spectrum Data
SML-D12V8W
SML-D12U8W
SML-D13U8W
SML-D12D8W
SML-D13Y8W
SML-D12Y8W
SML-D12M8W
SML-D13M8W
SML-D12P8W
IF=20mA
1.0
0.8
0.6
0.4
0.2
0.0
ꢀ
380
480
580
680
780
WAVELENGTH [nm]
* Please take this data as a reference data for the samples are measured randomly.
* The data is relativized for each color. It is NOT to show the spectrum peaks are equal.
Viewing Angle
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
4/8
Data Sheet
SML-D1 series
Rank Reference of Brightness
Red(V,U)
(Ta=25ºC, I 20mA)
＝
F
Rank
H
J
K
L
M
N
P
Q
R
S
T
U
Iv (mcd)
1.6 to 2.5
2.5 to 4.0
4.0 to 6.3
6.3 to 10
10 to 16
16 to 25
25 to 40
40 to 63
63 to 100
100 to 160
160 to 250
250 to 400
SML-D13U8W
SML-D12V8W
SML-D12U8W
Orange(D)
(Ta=25ºC, I 20mA)
＝
F
Rank
H
J
K
L
M
N
P
Q
R
S
T
U
Iv (mcd)
1.6 to 2.5
2.5 to 4.0
4.0 to 6.3
6.3 to 10
10 to 16
16 to 25
25 to 40
40 to 63
63 to 100
100 to 160
160 to 250
250 to 400
SML-D12D8W
Yellow(Y)
(Ta=25ºC, I 20mA)
＝
F
Rank
H
J
K
L
M
N
P
Q
R
S
T
U
Iv (mcd)
1.6 to 2.5
2.5 to 4.0
4.0 to 6.3
6.3 to 10
10 to 16
16 to 25
25 to 40
40 to 63
63 to 100
100 to 160
160 to 250
250 to 400
SML-D13Y8W
SML-D12Y8W
Green(M,P)
(Ta=25ºC, I 20mA)
＝
F
Rank
H
J
K
L
M
N
P
Q
R
S
T
U
Iv (mcd)
1.6 to 2.5
2.5 to 4.0
4.0 to 6.3
6.3 to 10
10 to 16
16 to 25
25 to 40
40 to 63
63 to 100
100 to 160
160 to 250
250 to 400
SML-D13M8W
SML-D12P8W
SML-D12M8W
4 ±0.1
2±0.05
＋0.1
0
Taping [T86]
φ1.5
+0.1
-0.07
1
+0.1
-0.07
0.73
11.4±1
Packing quantity
3000pcs/reel
Pull
direction
（Unit：mm)
(Note) Tolerance is within 0.2mm, unless otherwise specified.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
5/8
Data Sheet
SML-D1 series
Part No. Construction
Packing Specification
ROHM LED products are being shipped with desiccant (silica gel) concluded in moisture-proof bags.
Pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card
inside the bag is available upon request.
Please contact the nearest sales office or distributer if necessary.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
6/8
Data Sheet
SML-D1 series
Attention Points In Handling
0.8mm
(Fig-1)
0.8mm
This product was developed as a surface mount LED especially suitable for reflow soldering.
Please take care of following points when using this device.
1.DESIGNING OF PCB
0.85mm
0.8mm
As for a recommendable solder pattern, Please refer to Fig-1.
The size and direction of the pad pattern depend on the condition of the PCB.
Thorough design review is recommended before the final designing
PCB Bonding Direction
This product of structured with rear/bottom electrode to be soldered.
The formation of solder fillet is not guaranteed due to its electrode shape.
2.SOLDERING (Sn-Cu, Sn-Ag-Cu, Sn-Ag-Bi-Cu)
LED products do not contain reinforcement
materials such as glass fillers.
300
250
200
150
100
50
Max.260ºC, Within 10sec
140 to 180ºC
Therefore, thermal stress by soldering greatly
influence its reliability.
230 to 260ºC
The temperature conditions for reflow soldering
should therefore be set up according to the
characteristic of this product. (See Fig-2)
Number of reflow process shall be max 2 times
and these processes shall be performed in a row.
Cooling process to normal temperature shall be required
between first and second soldering process.
Min.1 min Max. 40sec
0
(Fig-2)
Emitting Direction
Mold
3.HANDLING AFTER MOUNTING (Fig-3)
Outside Force
As shown in the drawing on the right, in case outside force of
about 700g is given to the device, stress is concentrated to the
Substrate
jointed part between mold resin and substrate.
Therefore there is a possibility to breath the device or PCB.
Careful handing is needed as ROHM cannot guarantee
the falling of the device by outside force after mounting.
Soldering part
PCB
(Fig-3)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
7/8
Data Sheet
SML-D1 series
4.WASHING
Please note the following points when washing is required after soldering.
4-1) WASHING SOLVENT
Isopropyl alcohol or other alcohol solvent is recommendable.
4-2) TEMPERATURE
Below 30ºC, immersion time ; within 3 minutes.
4-3) ULTRA SONIC WASHING
Below 15/1 litter of solvent tub or less.
4-4) COOLING
Below 100ºC within 3 minutes.
5.EROSION GAS
Utilization in erosion gas atmosphere may degenerate the plating surface which might cause deterioration of
solder strength, optical characteristics, or functions.
Please take precautions against occurrence of gas from the surrounding parts on the occasion of custody,
and also after mounted on circuit board
6.STORAGE
At reflow soldering, the reliability of this product is often influenced by moisturet
absorption so we apply the packaging with moisture proof for better condition is use, please also note that
6-1) Not to be opened before using.
6-2) To be kept in our moisture proof packaging with some desiccant (SILICA GEL) after opening it.
To be baked in case the SILICA GEL indicator changed its color from either blue to clear or green to pink.
6-3) Please use within 168 hours after the package was opened. (Condition at 30 ºC, max.70%Rh.)
In case it is not used within 168 hours, please put it back into our packaging.
6-4) BAKING
Please bake under reel condition at 60ºC, 12～24 hours (max.20%Rh) after un-sealing.
While baking is done, the reel and emboss tape may be easily deformed.
Please be careful not to give any stress.
7.LIFE TIME
This product will cause reduction of luminous intensity depending on the using conditions and environmental.
Please inquire our sales contact if long life time is required on your application.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
2013.09 - Rev.D
8/8
Notice
N o t e s
1) The information contained herein is subject to change without notice.
2) Before you use our Products, please contact our sales representative and verify the latest specifica-
tions :
3) Although ROHM is continuously working to improve product reliability and quality, semicon-
ductors can break down and malfunction due to various factors.
Therefore, in order to prevent personal injury or fire arising from failure, please take safety
measures such as complying with the derating characteristics, implementing redundant and
fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no
responsibility for any damages arising out of the use of our Poducts beyond the rating specified by
ROHM.
4) Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral
conditions must be taken into account when designing circuits for mass production.
5) The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly,
any license to use or exercise intellectual property or other rights held by ROHM or any other
parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of
such technical information.
6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communi-
cation, consumer systems, gaming/entertainment sets) as well as the applications indicated in
this document.
7) The Products specified in this document are not designed to be radiation tolerant.
8) For use of our Products in applications requiring a high degree of reliability (as exemplified
below), please contact and consult with a ROHM representative : transportation equipment (i.e.
cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety
equipment, medical systems, servers, solar cells, and power transmission systems.
9) Do not use our Products in applications requiring extremely high reliability, such as aerospace
equipment, nuclear power control systems, and submarine repeaters.
10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with
the recommended usage conditions and specifications contained herein.
11) ROHM has used reasonable care to ensur the accuracy of the information contained in this
document. However, ROHM does not warrants that such information is error-free, and ROHM
shall have no responsibility for any damages arising from any inaccuracy or misprint of such
information.
12) Please use the Products in accordance with any applicable environmental laws and regulations,
such as the RoHS Directive. For more details, including RoHS compatibility, please contact a
ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting
non-compliance with any applicable laws or regulations.
13) When providing our Products and technologies contained in this document to other countries,
you must abide by the procedures and provisions stipulated in all applicable export laws and
regulations, including without limitation the US Export Administration Regulations and the Foreign
Exchange and Foreign Trade Act.
14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of
ROHM.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
R1102
A
相关型号：
SML-D12P8WT87L
Single Color LED, Green, Milky White, 1.2mm, 1.60 X 0.80 MM, 0.55 MM HEIGHT, 0603, 2 PIN
ROHM
SML-D12U1WT86
Single Color LED, Red, Milky White, 1.2mm, 1.60 X 0.80 MM, 0.55 MM HEIGHT, 0603, 2 PIN
ROHM
SML-D12U8W(C)
ROHM的贴片LED除标准型之外，还备有顶视型贴片LED、侧面发光贴片LED、适用于背面贴装的贴片LED等产品系列。其中，SML-D1系列是具有丰富色彩和光强的产品系列，是具有不俗销售业绩的大批量生产型封装。
ROHM
SML-D12U8WT86
Single Color LED, Red, Diffused Milky White, 1.2mm, 1.60 X 0.80 MM, 0.55 MM HEIGHT, ROHS COMPLIANT, 0603, 2 PIN
ROHM
©2020 ICPDF网 联系我们和版权申明