SMLK15WBFPW14P3 [ROHM]
Visible LED,;
ROHM 
1808<4.5 2.0 t=0.6mm>
High Brightness Type
PSML2 (SMLK15WB
Series)
∗∗∗∗
Tentative Spec
Emitting Color
Material
White
InGaN on Si
(mm)
Package Size
(
)
(
)
4520 1808 4.5×2.0 t=0.6
Part No.
PSML2 (SMLK15WBFPW)
note) "-" will be taken out for emitting color B/E series.
Absolute Maximum Ratings (Ta=25°C)
Dimensions (Unit:mm)
2
Peak
1.5
Anode mark
Power
Forward
Reverse Operating
Storage
forward
current
Emitting
color
dissipation current
voltage temperature temperature
Part No.
∗1
PD
(mW)
IF
VR
(V)
Topr
Tstg
(°C)
∗2
IFP
(mA)
(°C)
(mA)
SMLK15WBFPW
810
180
350
5
-40 to +100 -40 to +100
White
0.4
0.2
1:Subject to adequate heat-radiation conditions of mounting board (e.g. use of metallic board, use of Cu land patterns)
2:Duty 1/10, pulse width 10ms.
1.1
Electrical Optical Characteristics (Ta=25°C)
Brightness
IV
Forward
voltage
VF
Chromaticity
coordinates
Part No.
Resin
Typ.
IF
IF
Min.
Typ.
IF
x
y
0.30
( )
V
(
)
(
)
(
)
(
)
(
)
mA
mA
cd
cd
mA
1.54
Phosphor
included
Tolerance: 0.2
SMLK15WBFPW
3.8
100
0.30
100
−
6.4
100
Directivity (Typ.)
Chromaticity Diagram
(
)
Angular Displacement deg
0.38
0°
X
Y
30°
30°
0.36
0.34
60°
60°
3
0.32
5
2
90°
100
90°
100
8
0.30
50
0
50
(
)
%
RELATIVE LUMINOUS INTENSITY
4
7
0.28
1
(
)
Angular Displacement deg
0°
6
0.26
X’
Y’
30°
30°
0.24
0.26
0.28
0.30
0.32
0.34
60°
60°
CIE x
Chromaticity Coordinates (Ta=25˚C, IF=150mA)
1
2
3
4
5
6
7
8
x
y
x
y
x
y
x
y
x
y
x
y
x
y
x
y
90°
100
90°
100
50
0
50
0.280 0.248 0.287 0.295 0.307 0.315 0.296 0.276 0.311 0.294 0.282 0.246 0.300 0.269 0.313 0.285
0.264 0.267 0.283 0.305 0.304 0.330 0.287 0.295 0.307 0.315 0.280 0.248 0.296 0.276 0.311 0.294
0.283 0.305 0.304 0.330 0.330 0.360 0.307 0.315 0.330 0.339 0.296 0.276 0.311 0.294 0.330 0.318
0.296 0.276 0.307 0.315 0.330 0.339 0.311 0.294 0.330 0.318 0.300 0.269 0.313 0.285 0.330 0.304
Measurement tolerance: 0.02
(
)
%
RELATIVE LUMINOUS INTENSITY
Recommended Pad Layout
Packaging Specifications (Unit : mm)
Tape Specifications : 1 <4,000pcs / reel>
Reel Specifications
1.74
15.4
1
4
0.1
+0.1
φ
1.5
0
2
0.05
0.3 0.05
(Unit:mm)
The recommended thickness of the screen mask
for soldering is between 100 and 150µm. The
hole size of the screen mask should be same as
the recommended land pattern or smaller.
0.8 0.1
2.2 0.1
4
0.1
Tolerance: 0.2
Tolerance: 0.2
Rev.A
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
THE AMERICAS / EUROPE / ASIA / JAPAN
ROHM Customer Support System
Contact us : webmaster@ rohm.co.jp
www.rohm.com
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Copyright © 2008 ROHM CO.,LTD.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
Appendix1-Rev2.0
相关型号：
©2020 ICPDF网 联系我们和版权申明