TCTCL0E477MCR [ROHM]

Chip tantalum capacitors; 贴片钽电容


型号：	TCTCL0E477MCR
厂家：	ROHM
描述：	Chip tantalum capacitors 贴片钽电容
文件：	总6页 (文件大小：131K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Chip tantalum capacitors

TCT Series CL Case

zFeatures (CL)

zDimensions (Unit : mm)

1) Vital for all hybrid integrated circuits

board application.

Anode mark

2) Wide capacitance range.

3) Screening by thermal shock.

(Unit : mm)

CL case

Dimensions

6.0 0.2

−

3.2 0.2

−

2.2 0.2

−

1.4 0.1

−

1.3 0.2

−

zPart No. Explanation

T C T C L 1 A 1 5 7 M C R

Nominal capacitance

Series name

TCT

Nominal capacitance in pF in 3 digits:

2 significant figures followed by the figure

representing the number of 0's.

Case style

Capacitance tolerance

M : 20%

−

Rated voltage

2.5

4 6.3 10 16 20 25

Rated voltage (V)

CODE

Taping

0E 0G 0J 1A 1C 1D 1E

C : Tape width (12mm)

Positive electrode on the side opposite to sprocket hole

R :

z Rated table

Rated voltage (V)

2.5

6.3

(µF)

∗

10 (106)

100 (107)

150 (157)

220(227)

330(337)

470(477)

∗

Remark) Case size codes (CL) in the above show products line-up.

Under development

∗

www.rohm.com

2009.01 - Rev.D

1/5

TCT Series CL Case

Data Sheet

z Marking

The indications listed below should be given on the surface of a capacitor.

(1) Polarity

(2) Rated DC voltage

(3) Visual typical example

(1) capacitance code (2) voltage code

10V

(1)

150

(2)

[CL case]

note 1)

150

10V

note 2) voltage code and capacitance code are variable with parts number

z Characteristics

Item

Performance

−55°C to +125°C

+85°C

Test conditions (based on JIS C 5101−1 and JIS C 5101−3)

Voltage reduction when temperature exceeds +85°C

Operating Temperature

Maximum operating

temperature with no voltage

derating

Rated voltage (VDC)

Category voltage (VDC)

Surge voltage (VDC)

DC Leakage current

2.5

6.3 10 16 20 25 35

at 85°C

at 125°C

at 85°C

1.6 2.5

3.2 5.0

6.3 10 13 16 22

13 20 26 32 44

Shall be satisfied the voltage on

" Standard list "

As per 4.9 JIS C 5101-1

As per 4.5.1 JIS C 5101-3

Voltage : Rated voltage for 5min

Capacitance tolerance

As per 4.7 JIS C 5101-1

As per 4.5.2 JIS C 5101-3

Shall be satisfied allowance range.

20%

Measuring frequency : 120

Measuring voltage : 0.5Vrms +1.5 to 2V.DC

Measuring circuit : DC Equivalent series circuit

±12Hz

Tangent of loss angle

(Df, tan δ)

Shall be satisfied the voltage on

" Standard list "

As per 4.8 JIS C 5101-1

As per 4.5.3 JIS C 5101-3

Measuring frequency : 120

12Hz

Measuring voltage : 0.5Vrms +1.5 to 2V.DC

Measuring circuit : DC Equivalent series circuit

As per 4.10 JIS C 5101-1

As per 4.5.4 JIS C 5101-3

Measuring frequency : 100

Impedance

Shall be satisfied the voltage on

" Standard list "

10kHz

Measuring voltage : 0.5Vrms or less

Measuring circuit

: DC Equivalent series circuit

Resistance to Appearance There should be no significant abnormality.

As per 4.14 JIS C 5101-1

As per 4.6 JIS C 5101-3

Dip in the solder bath

Soldering heat

The indications should be clear.

L.C.

Less than 200% of initial limit

Within 20% of initial value

Less than 200% of initial limit

Solder temp

Duration

: 260

: 5±

±5°C

0.5s

∆C / C

Repetition

: 1

Df (tan δ)

After the specimens, leave it at room temperature for

over 24h and then measure the sample.

Temperature

cycle

Appearance

There should be no significant abnormality.

The indications should be clear.

As per 4.16 JIS C 5101-1

As per 4.10 JIS C 5101-3

Repetition : 5 cycles

(1 cycle : steps 1 to 4) without discontinuation.

Less than 200%of initial limit

L.C.

∆C / C

Df (tan δ)

Within 20% of initial value

Less than 200%of initial limit

Temp.

Time

−55 3°C

30 3min.

−

Room temp. 3min. or less

125 2°C

30 3min.

−

Room temp. 3min. or less

After the specimens, leave it at room temperature for

over 24h and then measure the sample.

Moisture

resistance

Appearance There should be no significant abnormality.

The indications should be clear.

As per 4.22 JIS C 5101-1

As per 4.12 JIS C 5101-3

After leaving the sample under such atmospheric

condition that the temperature and humidity are

60 2°C and 90 to 95% RH, respectiveiy, for 500 12h

leave it at room

temperature for over 24h and then measure the

sample.

L.C.

Less than 200% of initial limit

Within 20% of initial value

Less than 200% of initial limit

∆C / C

Df (tan δ)

www.rohm.com

2009.01 - Rev.D

2/5

TCT Series CL Case

Data Sheet

Item

Performance

Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)

As per 4.29 JIS C 5101-1

As per 4.13 JIS C 5101-3

Temperature

Stability

Temp.

∆C / C

Df (tan δ)

L.C.

−55°C

Within 0/−15% of initial value

Shall be satisfied the voltage on " Standard list "

−

Temp.

∆C / C

+85°C

Within +15/−5% of initial value

Df (tan δ)

L.C.

Shall be satisfied the voltage on " Standard list "

5µA or 0.1CV whichever is greater

+125°C

Temp.

∆C / C

Df (tan δ)

L.C.

Within +20/−5% of initial value

Shall be satisfied the voltage on " Standard list "

6.3µA or 0.2CV whichever is greater

There should be no significant abnormality.

As per 4.26JIS C 5101-1

Surge voltage Appearance

As per 4.14JIS C 5101-3

L.C.

Less than 200% of initial limit

Within 20% of initial value

Less than 200% of initial limit

Apply the specified surge voltage every 5 0.5 min.

for 30 5 s. each time in the atmospheric condition of 85 2°C.

Repeat this procedure 1,000 times.

After the specimens, leave it at room temperature for

over 24h and then measure the sample.

∆C / C

Df (tan δ)

Loading at

High temperature

Appearance

L.C.

There should be no significant abnormality.

Less than 200% of initial limit

As per 4.23 JIS C 5101-1

As per 4.15 JIS C 5101-3

After applying the rated voltage for 1000+36/0 h without

discontinuation via the serial resistance of 3Ω or less

at a temperature of 85 2°C, leave the sample at room

temperature / humidity for over 24h and measure the value.

∆C / C

Within 20% of initial value

Less than 200% of initial limit

Df (tan δ)

Terminal

strength

Capacitance

Appearance

The measured value should be stable.

As per 4.35 JIS C 5101-1

As per 4.9 JIS C 5101-3

A force is applied to the terminal until it bends to 1mm and

by a prescribed tool maintain the condition for 5s.

There should be no significant abnormality.

(See the figure below)

(Unit : mm)

F (Apply force)

R230

thickness=1.6mm

www.rohm.com

2009.01 - Rev.D

3/5

TCT Series CL Case

Data Sheet

Item

Performance

Test conditions (JIS C 5101−1 and JIS C 5101− 3)

As per 4.34 JIS C 5101-1

As per 4.8 JIS C 5101-3

Adhesiveness

The terminal should not come off.

Apply force of 5N in the two directions shown in the figure

below for 10 1s after mounting the terminal on a circuit board.

product

Apply force

a circuit board

Dimensions

Refer to "External dimensions"

Measure using a caliper of JIS B 7507 Class 2

or higher grade.

Resistance to solvents The indication should be clear

As per 4.32 JIS C 5101-1

As per 4.18 JIS C 5101-3

Dip in the isopropyl alcohol for 30 5s, at room

temperature.

Solderability

As per 4.15.2 JIS C 5101-1

3/4 or more surface area of the solder coated

As per 4.7 JIS C 5101-3

Dip speed=25 2.5mm / s

terminal dipped in the soldering bath should

be covered with the new solder.

Pre−treatment(accelerated aging): Leave

the sample on the boiling distilled water for 1 h.

Solder temp. : 245 5°C

Duration

Solder

Flux

: 3 0.5s

: M705

: Rosin 25% IPA 75%

As per 4.17 JIS C 5101-1

Frequency : 10 to 55 to 10Hz/min.

Amplitude : 1.5mm

Measure value should not fluctuate during the

measurement.

Vibration

Capacitance

Time : 2h each in X and Y directions

Mounting : The terminal is soldered on a print circuit board.

Appearance There should be no significant abnormality.

z Standard products list, TCT series CL case

120Hz

(%)

Impedance

100kHz

Leakage

current

25°C

1WV.60s

(µA)

Rated

voltage

85°C

TCTCL0E477MCR [ROHM]

相关型号：

TCTCL0E685M8R

TCTCL0E686M8R

TCTCL0G106M8R

TCTCL0G106MCR

TCTCL0G107M8R

TCTCL0G107MCR

TCTCL0G156M8R

TCTCL0G157M8R

TCTCL0G157MCR

TCTCL0G225M8R

TCTCL0G226M8R

TCTCL0G227M8R