TCTCL0G337M8R [ROHM]
Chip tantalum capacitors (Bottom surface electrode type);型号: | TCTCL0G337M8R |
厂家: | ROHM |
描述: | Chip tantalum capacitors (Bottom surface electrode type) |
文件: | 总6页 (文件大小:152K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Chip tantalum capacitors (Bottom surface electrode type)
TCT Series CL Case
Features (CL)
Dimensions (Unit : mm)
1) Vital for all hybrid integrated circuits
board application.
Anode mark
2) Wide capacitance range.
3) Screening by thermal shock.
(Unit : mm)
CL case
Dimensions
L
+
6.0 0.2
−
+
3.2 0.2
−
W
W
1
+
2
2.2 0.2
−
+
1.4 0.1
−
H
S
+
1.3 0.2
−
+
−
Part No. Explanation
T C T C L 1 A 1 5 7 M C R
5
1
2
3
4
6
Nominal capacitance
1
2
4
Series name
TCT
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure
representing the number of 0's.
Case style
TC
CL
5
6
Capacitance tolerance
+
M : 20%
−
Rated voltage
3
2.5
4 6.3 10 16
Rated voltage (V)
CODE
Taping
0E 0G 0J 1A 1C
C : Reel width : 12mm
Positive electrode on the side opposite to sprocket hole
R :
Rated table
Rated voltage (V)
2.5
0E
4
0G
6.3
0J
10
1A
16
1C
(μF)
10 (106)
100 (107)
150 (157)
220(227)
330(337)
470(477)
∗
CL
∗
CL
∗
CL
∗
CL
∗
CL
Remark) Case size codes (CL) in the above show products line-up.
Under development
∗
www.rohm.com
2010.02 - Rev.F
1/5
c
○ 2010 ROHM Co., Ltd. All rights reserved.
TCT Series CL Case
Data Sheet
Marking
The indications listed below should be given on the surface of a capacitor.
(1) Polarity
(2) Rated DC voltage
(3) Visual typical example
(1) capacitance code (2) voltage code
10V
(1)
150
(2)
[CL case]
note 1)
150
10V
note 2) voltage code and capacitance code are variable with parts number
Characteristics
Item
Performance
−55°C to +125°C
+85°C
Test conditions (based on JIS C 5101−1 and JIS C 5101−3)
Voltage reduction when temperature exceeds +85°C
Operating Temperature
Maximum operating
temperature with no voltage
derating
Rated voltage (VDC)
Category voltage (VDC)
Surge voltage (VDC)
DC Leakage current
2.5
4
6.3 10 16
at 85°C
at 125°C
at 85°C
1.6 2.5
3.2 5.0
4
8
6.3 10
13 20
Shall be satisfied the voltage on
" Standard list "
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
Voltage : Rated voltage for 5min
Capacitance tolerance
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
Shall be satisfied allowance range.
±20%
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
Measuring circuit
: DC Equivalent series circuit
Tangent of loss angle
(Df, tan δ)
Shall be satisfied the voltage on
" Standard list "
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
Measuring frequency : 120±12Hz
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
Measuring circuit
: DC Equivalent series circuit
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
Impedance
Shall be satisfied the voltage on
" Standard list "
Measuring frequency : 100±10kHz
Measuring voltage : 0.5Vrms or less
Measuring circuit
: DC Equivalent series circuit
Resistance to Appearance There should be no significant abnormality.
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Soldering heat
The indications should be clear.
L.C.
Less than 200% of initial limit
Within 20% of initial value
Less than 200% of initial limit
Solder temp
Duration
Repetition
: 260±5°C
5±0.5s
: 1
:
ΔC / C
Df (tan δ)
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Temperature
cycle
Appearance
There should be no significant abnormality.
The indications should be clear.
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
Less than 200%of initial limit
L.C.
ΔC / C
Df (tan δ)
Within 20% of initial value
Less than 200%of initial limit
Temp.
Time
+
1
2
3
4
−55 3°C
30 3min.
−
Room temp. 3min. or less
+
125 2°C
30 3min.
−
Room temp. 3min. or less
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Moisture
resistance
Appearance There should be no significant abnormality.
The indications should be clear.
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
After leaving the sample under such atmospheric
condition that the temperature and humidity are
60 2°C and 90 to 95% RH, respectiveiy, for 500 12h
leave it at room
temperature for over 24h and then measure the
sample.
L.C.
Less than 200% of initial limit
Within 20% of initial value
Less than 200% of initial limit
ΔC / C
Df (tan δ)
www.rohm.com
2010.02 - Rev.F
2/5
c
○ 2010 ROHM Co., Ltd. All rights reserved.
TCT Series CL Case
Data Sheet
Item
Performance
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
Temperature
Stability
Temp.
ΔC / C
Df (tan δ)
L.C.
−55°C
Within 0/−15% of initial value
Shall be satisfied the voltage on " Standard list "
−
Temp.
ΔC / C
+85°C
Within +15/−5% of initial value
Df (tan δ)
L.C.
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial limit
+125°C
Temp.
ΔC / C
Df (tan δ)
L.C.
Within +20/−5% of initial value
Shall be satisfied the voltage on " Standard list "
Less than 1250% of initial limit
There should be no significant abnormality.
As per 4.26JIS C 5101-1
Surge voltage Appearance
As per 4.14JIS C 5101-3
L.C.
Less than 200% of initial limit
Within 20% of initial value
Less than 200% of initial limit
Apply the specified surge voltage via the serial resistance of
1kΩ every 5 0.5 min.for 30 5 s. each time in the atmospheric
condition of 85 2°C. Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
ΔC / C
Df (tan δ)
Loading at
High temperature
Appearance
L.C.
There should be no significant abnormality.
Less than 200% of initial limit
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 1000+36/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85 2°C, leave the sample at room
temperature / humidity for over 24h and measure the value.
ΔC / C
Within 20% of initial value
Less than 200% of initial limit
Df (tan δ)
Terminal
strength
Capacitance
Appearance
The measured value should be stable.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
There should be no significant abnormality.
(See the figure below)
(Unit : mm)
20
50
F (Apply force)
R230
1
thickness=1.6mm
45
45
www.rohm.com
2010.02 - Rev.F
3/5
c
○ 2010 ROHM Co., Ltd. All rights reserved.
TCT Series CL Case
Data Sheet
Item
Performance
Test conditions (JIS C 5101−1 and JIS C 5101− 3)
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Adhesiveness
The terminal should not come off.
Apply force of 5N in the two directions shown in the figure
below for 10 1s after mounting the terminal on a circuit board.
product
Apply force
a circuit board
Dimensions
Refer to "External dimensions"
Measure using a caliper of JIS B 7507 Class 2
or higher grade.
Resistance to solvents The indication should be clear
As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30 5s, at room
temperature.
Solderability
As per 4.15.2 JIS C 5101-1
3/4 or more surface area of the solder coated
As per 4.7 JIS C 5101-3
Dip speed=25 2.5mm / s
terminal dipped in the soldering bath should
be covered with the new solder.
Pre−treatment(accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245 5°C
Duration
Solder
Flux
: 3 0.5s
: M705
: Rosin 25% IPA 75%
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Measure value should not fluctuate during the
measurement.
Vibration
Capacitance
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board.
Appearance There should be no significant abnormality.
Standard products list, TCT series CL case
Df
120Hz
(%)
Impedance
100kHz
Leakage
current
25°C
1WV.60s
(μA)
Rated
voltage
85°C
Category
voltage
125°C
Surge
voltage
85°C
Cap.
120Hz
Tolerance
(%)
Part No.
25°C
85°C
(μF)
−55°C
125°C
(Ω)
(V)
(V)
(V)
∗
TCT CL 0E 477M8R
TCT CL 0G 337M8R
TCT CL 0J 227M8R
TCT CL 1A 157M8R
TCT CL 1C 107M8R
2.5
4
1.6
2.5
4
3.2
5
470
330
220
150
100
20
20
20
20
20
11.8
13.2
13.9
15.0
16.0
36
34
32
30
28
18
16
14
12
10
28
24
20
16
14
0.5
0.7
0.8
1.3
1.6
∗
∗
6.3
10
16
8
∗
∗
6.3
10
13
20
=
∗
Under development
Packaging specifications
+
+
+
+
t2 0.1
−
Case code
A
0.1
B
0.1
t
1
0.05
−
−
−
3.5
6.6
0.3
1.7
CL
Taping [CL case]
0.1
0
t
1
φ1.5
A
B
Chip
8.0±
0.1
2.0
4.0±0.1
t
2
±
0.1
Feeding direction
www.rohm.com
2010.02 - Rev.F
4/5
c
○ 2010 ROHM Co., Ltd. All rights reserved.
TCT Series CL Case
Data Sheet
Packaging style
Case code
CL case
Packaging
Taping
Packaging style
Symbol Basic ordering units
1,000pcs
plastic taping φ180mm Reel
R
Reel [CL case]
+
15.4 1.0
−
Pull direction
Label sticking position
EIAJ ET−7200B compatible
Damp proof package
One reel is packed in aluminum bag.
The size of aluminum bag is 240(a) x 250(b)mm.
The size up to 230(c)mm is to zipper.
A desiccant is packed with a reel.
The aluminum bag is heat-sealed.
The label of the same as the label on the reel is placed on the aluminum bag.
b
c
a
www.rohm.com
2010.02 - Rev.F
5/5
c
○ 2010 ROHM Co., Ltd. All rights reserved.
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
R1010
A
相关型号:
©2020 ICPDF网 联系我们和版权申明