TCTOAL0G686M8R [ROHM]
Conductive polymer chip tantalum capacitors ( Bottom surface electrode type ); 导电聚合物贴片钽电容（底面电极型）
| 型号： | TCTOAL0G686M8R |
| 厂家： | 
ROHM |
| 描述： | Conductive polymer chip tantalum capacitors ( Bottom surface electrode type ) |
| 文件： | 总6页 (文件大小：167K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Conductive polymer chip tantalum capacitors
( Bottom surface electrode type )
TCTO Series AL Case
zFeatures (AL)
zDimensions (Unit : mm)
1) Conductive polymer used for the cathode material.
2) Ultra low ESR
Anode mark
3) Small package, but big capacitance
4) Screening by thermal shock
(Unit : mm)
AL case
H
Dimensions
L
+
3.2 0.2
−
W
1
L
+
1.6 0.2
−
W
W
1
+
2
1.2 0.2
−
+
1.1 0.1
−
+
0.8 0.2
−
H
S
W
2
S
S
zPart No. Explanation
T C T O A L 0 J 4 7 6 M 8 R
5
1
2
3
4
6
Nominal capacitance
1
2
4
Series name
TCTO
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure
representing the number of 0's.
Case style
AL
5
6
Capacitance tolerance
+
M : 20%
−
Rated voltage
3
2.5
4 6.3 10
0E 0G 0J 1A
Rated voltage (V)
CODE
Taping
Tape width
8 :
Positive electrode on the side opposite to sprocket hole
R :
∗ This specification has possibility of charge, due to underdevelopment product.
Please ask for latest specification to our sales.
www.rohm.com
2009.04 - Rev.B
1/5
c
○ 2009 ROHM Co., Ltd. All rights reserved.
TCTO Series AL Case
Data Sheet
z Rated table
Rated voltage (V)
(µF)
2.5
0E
4
0G
6.3
0J
10
1A
1.0 (105)
2.2 (225)
3.3 (335)
4.7 (475)
6.8 (685)
10 (106)
15 (156)
22 (226)
33 (336)
47 (476)
68 (686)
100 (107)
150 (157)
220 (227)
∗
AL
∗
AL
∗
AL
∗
AL
AL
AL
AL
AL
AL
Remark) Case size codes (AL) in the above show products line-up.
∗
Under development
z Marking
The indications listed below should be given on the surface of a capacitor.
(1) Polarity
(2) Rated DC voltage : Due to the small size of AL case, a voltage code is used as shown below.
(3) Visual typical example (1) voltage code (2) capacitance code
: The polarity should be shown by bar. (on the anode side)
Voltage
Code
Rated DC
Voltage (V)
Nominal
Capacitance (µF)
Capacitance
Code
e
g
j
2.5
4
A
E
1.0
1.5
6.3
10
J
N
S
W
a
2.2
3.3
4.7
6.8
10
A
e
j
15
22
n
s
33
47
w
a
68
100
j
s
[AL case]
note 1)
− −
(1) (2)
j s
manufacture code
note 2) voltage code and capacitance code are variable with parts number
www.rohm.com
2009.04 - Rev.B
2/5
c
○ 2009 ROHM Co., Ltd. All rights reserved.
TCTO Series AL Case
Data Sheet
z Characteristics
Item
Performance
−55°C to +105°C
+85°C
Test conditions (based on JIS C 5101−1 and JIS C 5101−3)
Voltage reduction when temperature exceeds +85°C
Operating Temperature
Maximum operating
temperature with no voltage
derating
Rated voltage (VDC)
Category voltage (VDC)
Surge voltage (VDC)
DC Leakage current
2.5
4
6.3 10
at 85°C
at 105°C
at 85°C
1.6 2.5
3.2 5.0
4
8
6.3
13
Shall be satisfied the voltage on
" Standard list "
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
Voltage : Rated voltage for 5min
Capacitance tolerance
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
Shall be satisfied allowance range.
20%
Measuring frequency : 120
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
Measuring circuit : DC Equivalent series circuit
±12Hz
Tangent of loss angle
(Df, tan δ)
Shall be satisfied the voltage on
" Standard list "
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
Measuring frequency : 120 12Hz
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
Measuring circuit
: DC Equivalent series circuit
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
ESR
Shall be satisfied the voltage on
" Standard list "
Measuring frequency : 100 10kHz
Measuring voltage : 0.5Vrms or less
Measuring circuit
: DC Equivalent series circuit
Resistance to Appearance There should be no significant abnormality.
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Soldering heat
The indications should be clear.
L.C.
Less than 300% of initial limit
Within 20% of initial value
Less than 300% of initial limit
Solder temp
Duration
Repetition
: 240 5°C
10 0.5s
: 1
:
∆C / C
Df (tan δ)
After the specimens, leave it at room temperature
for over 24h and then measure the sample.
Temperature
cycle
Appearance
There should be no significant abnormality.
The indications should be clear.
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
L.C.
Less than 1000% of initial limit
Within 20% of initial value
Less than 300% of initial limit
∆C / C
Df (tan δ)
Temp.
Time
1
2
3
4
−55 3°C
30 3min.
Room temp. 3min. or less
105 2°C 30 3min.
Room temp. 3min. or less
Moisture
resistance
Appearance There should be no significant abnormality.
The indications should be clear.
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
After leaving the sample under such atmospheric
condition that the temperature and humidity are
40 2°C and 90 to 95% RH, respectiveiy, for 500 12h
leave it at room
L.C.
Less than 300% of initial limit
Within +30/−20% of initial value
∆C / C
Df (tan δ)
Less than 300% of initial limit
temperature for 24h and then measure the sample.
www.rohm.com
2009.04 - Rev.B
3/5
c
○ 2009 ROHM Co., Ltd. All rights reserved.
TCTO Series AL Case
Data Sheet
Item
Performance
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
Temperature
Stability
Temp.
∆C / C
Df (tan δ)
L.C.
−55°C
Within 0/−20% of initial value
Shall be satisfied the voltage on " Standard list "
−
Temp.
+105°C
∆C / C
Within +50/0% of initial value
Shall be satisfied the voltage on " Standard list "
Less than 1.0CV
Df (tan δ)
L.C.
As per 4.26JIS C 5101-1
There should be no significant abnormality.
Surge voltage Appearance
As per 4.14JIS C 5101-3
Apply the specified surge voltage every 5 0.5 min.
for 30 5 s. each time in the atmospheric condition of 85 2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
L.C.
Less than 200% of initial value
Within 20% of initial value
∆C / C
Df (tan δ)
Less than 200% of initial limit
Loading at
High temperature
Appearance
L.C.
There should be no significant abnormality.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 1000+36/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85 2°C, leave the sample at room
temperature / humidity for 24h and measure the value.
Less than 400% of initial limit
Within 20% of initial value
∆C / C
Df (tan δ)
Less than 300% of initial limit
Terminal
strength
Capacitance
Appearance
The measured value should be stable.
There should be no significant abnormality.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
(Unit : mm)
20
50
F (Apply force)
R230
1
thickness=1.6mm
45
45
Item
Performance
Test conditions (JIS C 5101−1 and JIS C 5101− 3)
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Adhesiveness
The terminal should not come off.
Apply force of 5N in the two directions shown in the figure
below for 10 1s after mounting the terminal on a circuit board.
product
Apply force
a circuit board
Dimensions
Refer to "External dimensions"
Measure using a caliper of JIS B 7507 Class 2
or higher grade.
Resistance to solvents The indication should be clear
As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30 5s, at room
temperature.
Solderability
As per 4.15.2 JIS C 5101-1
3/4 or more surface area of the solder coated
As per 4.7 JIS C 5101-3
Dip speed=25 2.5mm / s
terminal dipped in the soldering bath should
be covered with the new solder.
Pre-treatment (accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245 5°C
Duration
Solder
Flux
: 3 0.5s
: M705
: Rosin 25% IPA 75%
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Measure value should not fluctuate during the
measurement.
Vibration
Capacitance
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board.
Appearance There should be no significant abnormality.
www.rohm.com
2009.04 - Rev.B
4/5
c
○ 2009 ROHM Co., Ltd. All rights reserved.
TCTO Series AL Case
Data Sheet
Df
120Hz
(%)
ESR
100kHz
Rated
voltage
85°C
Category
voltage
125°C
Surge
voltage
85°C
Leakage
current
25°C
1WV.5min
(µA)
Cap.
120Hz
Tolerance
(%)
Part No.
25°C
85°C
−55°C
105°C (mΩ)
(V)
(V)
(V)
(µF)
2.5
4
2
3.2
5
3.2
5.2
8
100
68
20
20
20
20
20
20
20
20
20
25.0
27.2
29.6
3.3
10
10
10
6
10
10
10
6
15
15
15
9
200
200
200
300
300
300
200
200
200
TCTO AL 0E 107
TCTO AL 0G 686
TCTO AL 0J 476
TCTO AL 1A 335
TCTO AL 1A 475
TCTO AL 1A 685
TCTO AL 1A 106
TCTO AL 1A 226
TCTO AL 1A 336
6.3
10
10
10
10
10
10
47
∗
∗
∗
∗
8
13
13
13
13
13
13
3.3
4.7
6.8
10
8
4.7
6
6
9
8
6.8
6
6
9
8
10.0
22.0
33.0
6
6
9
8
22
6
6
9
8
33
10
10
15
=Tolerance(M : 20%)
=Under development
∗
Case code
AL
A
0.1
B
0.1
t
1
0.05
t2 0.1
±
±
±
±
1.9
3.5
0.25
1.3
Taping [AL case]
t
1
+0.1
φ1.5
−0
B
Chip
A
Positiv
Electrode(+)
4.0±
0.1
2.0
4.0
0.05
±0.1
±
t2
Feeding direction
Case code
AL case
Packaging
Taping
Packaging style
Symbol Basic ordering units
3,000pcs
plastic taping φ180mm Reel
R
Reel [AL case]
+
11.4 1.0
−
Pull direction
Label sticking position
EIAJ ET−7200A
www.rohm.com
2009.04 - Rev.B
5/5
c
○ 2009 ROHM Co., Ltd. All rights reserved.
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039
A
相关型号：
©2020 ICPDF网 联系我们和版权申明