TRR01MZPF2491 [ROHM]
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 2490ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP;型号: | TRR01MZPF2491 |
厂家: | ROHM |
描述: | Fixed Resistor, Metal Glaze/thick Film, 0.063W, 2490ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP 电阻器 |
文件: | 总7页 (文件大小:571K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sulfur tolerant chip resistors
TRR series
Datasheet
●Features
1)Special construction prevents sulfur gas penetration, significantly increasing reliability.
2)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.
●Productslist
Rated Limiting
Operating
temperature
range
Size
Temperature Resistance
Part No.
power element
Resistce range
coefficient
tolerance
(70℃)
(W)
voltage
(V)
(mm)
1005
(inch)
0402
(ppm / ℃)
±100
(%)
(℃)
F( ±1%)
J( ±5%)
J( ±5%)
10≦.2M (E24/96 series)
0.063
0.10
50
50
+500 / -250
±200
.0≦R<10
(E24 series)
TRR01
TRR03
-55~ +155
R≦10M (E24 series)
Jumper type: Rmax =50/ Imax =1A
±100
±400
±200
F( ±1
%)
±5%)
10≦R≦10M (E24/96 series)
1≦R<10 E24 series)
10≦R10M (E24 series)
1608
0603
-55~ +155
Jumper tye: Rmax =50mΩ / Imax
±10
±40
±00
F( ±1%)
J( ±5%)
J( ±5%)
0≦R≦2.2M (E24/96 series)
1.0≦R<10 (E24 series)
10≦R≦10M (E24 series)
0.125
0.25
150
TRR10
TRR18
2012
3216
0805
1206
-55~ +155
-55~ +155
umper type: Rma0mΩ / Imax =2A
F( %
±5%)
J( ±5%)
(E24/96 series)
(E24 series)
±100
±400
±200
10≦R≦2.2M
1.0≦R<10
10≦R≦10M (E24 series)
Jumper type: Rmax =50mΩ / Imax =2A
Design and specifications arbject to change without otice.
※
Carefullycheck the specificn sheet supplied with he oduct before using or ordering it.
●Part Number ription
T R R
0 1
M Z P
J
1 0 5
Part No.
Size (mm [inch])
Packagingspecifications code
Resistance
tolerance
Nominal resistance
Resistance code, 3 or 4 digits.
000 denotes jumper type.
Packaging Quantity
Part No. Code
TRR01 MZP
TRR03 EZP
TRR10 EZP
TRR18 EZP
01 (1005 [0402])
03 (1608 [0603])
10 (2012 [0805])
18 (3216 [1206])
TR
specifications / Reel
Paper tape
(Sulftolerant
ip tors)
F( ±1%)
J( ±5%)
Resistance
tolerance
Resistance
code
10,000
(2mm Pitch)
Paper tape
(4mm Pitch)
4 digits
3 digits
F
J
:
5,000
:
EX.)
Paper tape
(4mm Pitch)
5,000
1Ω=1R0 ( ±5%)
9.1Ω=9R1 ( ±5%)
10Ω=10R0 ( ±1%)
100 ( ±5%)
Paper tape
(4mm Pitch)
5,000
1MΩ=1004 ( ±1%)
105 ( ±5%)
www.rohm.com
c 2016 ROHMCo., Ltd.All rights reserved.
1/4
2014.12 - Rev.C
TRR series
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Datasheet
●Chip resistor dimensions and markings
■TRR01/03
■TRR10/18
nit:mm)
Marking existence
Part No.
TRR01
TRR03
TRR10
TRR18
(mm)
1005
1608
2012
3216
(inch)
0402
0603
0805
1206
L
W
t
a
*Including jumper type
ꢀ
ꢀ
+0.05
0.25
ꢀ ꢀ ꢀ -0.10
ꢀ
1.00±0.05
0.50±0.05
0.35±0.05
0..08
No
No
No
No
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ
ꢀ
1.60±0.10
0.80±0.10
0.45±0.1
40±0.10
0.30.20
ꢀ
ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ
ꢀ
ꢀ
+0.15
2.00±0.10
1.25±0.10
0.50.10
0.43
40±0.20
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ
ꢀ ꢀ -ꢀ
ꢀ
ꢀ
+0.2
ꢀ
3.20±0.15
1.60±05
0.55±0.10
0.69
0.50±0.25
ꢀ ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ ꢀ
-0.15 ꢀ ꢀ ꢀ
●Land pattern example
(Unit:mm)
imensions
A
B
C
D
rt No.
TRR01
TRR03
TRR10
TRR18
0.5
1.0
1.2
2.2
1.3
2.0
2.6
4.0
0.5
0.8
1.15
1.5
0.4
0.5
0.7
0.9
www.rohm.com
c 2016 ROHMCo., Ltd.All rights reserved.
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
2/4
2014.12 - Rev.C
TRR series
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Datasheet
●Derating curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.
■TRR01/03/10/18
●Characteristics
Guaranteed value
Test items
Test conditions
Resistor type
Jumper type
Resistance
See P.1
See P.1
20
Variation of resistance
with temperature
easurement:+25125
Rated volage(rrent)×2.5, 2s
Maximerload voltage
Overload
±(2.0%+0.1Ω)
MAX. 50Ω
Anew uniform coatinf miimum
of 95%of the surce bng
immersed ano sodering
damage.
Rosiethanol solution(25%weight)
Sdering condition:245±5℃
Duration of immersion:2.0±0.5s
Solderability
ꢀ
ꢀ
±(1.0%+0.05Ω)
MAX. 50m
Soldering condition:260±5℃
Duration of immersion:10±1s
Resistance to
soldering heat
No remarkbnormalityon arance.
±(.0%0.05Ω)
(3.0%+0.1Ω)
±(3.+Ω)
MAX. 0mΩ
MAX. 100mΩ
MAX. 100mΩ
Rapid change of
temperature
Test temp:-55℃~+125℃ 5cycle
40℃,93%(Relative humidity)
Test time:1,000h
Damp heat, steadys
Rated voltage(current),70℃
1.5h:ON-0.5h:OFF
Test time:1,000h
Endurance a℃
±(3.0%+0.1Ω)
±(1.0%+0.05Ω)
±(1.0%+0.05Ω)
MAX. 100mΩ
MAX. 50mΩ
MAX. 50mΩ
155℃
Test time:1,000h
Enran
23±5℃, Immersion cleaning, 5±0.5min
Solvent: 2-propanol
Ristance to solvent
Bend strength of
the end face plating
-
Without mechanical damage such as breaks.
Compliance Standard(s) : IEC60115-8
JISC 5201-8
www.rohm.com
c 2016 ROHMCo., Ltd.All rights reserved.
ꢀ
ꢀ
ꢀ ꢀ ꢀ ꢀ
3/4
2014.12 - Rev.C
TRR series
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Datasheet
(Unit : mm)
●Tape dimensions
■Paper tape
Part No.
W
F
E
A0
B0
ꢀ
ꢀ
ꢀ
ꢀ
8.0±0.3
3.5±0.05
1.75±0.1
0.7±0.1
1.2±0.1
TRR01
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
8.0±0.3
ꢀ
3.5±0.05
ꢀ
1.75±0.1
1.1±0.1
ꢀ
1.9±0.1
ꢀ
TRR03
TRR10
TRR18
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ +0.2
1.65
ꢀ +0.2
2.4
8.0±0.3
ꢀ
3.5±0.05
ꢀ
1.75±0.1
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
-0.1
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
1.9
ꢀ +0.15
8.0±0.3
ꢀ
3.5±0.05
ꢀ
1.75±0.1
3.5
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
-0.05
P2
-0.05
Part No.
D0
P0
P1
T2
+0.1
ꢀ
ꢀ
ꢀ
MAX
Φ1.5
4.0±0.1
±0.05
2.0±0.05
1.1
1.1
1.1
1.1
TRR01
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
0
ꢀ
ꢀ +0.1
ꢀ
ꢀ
ꢀ ꢀ
MAX
Φ1.5
ꢀ ꢀ
±0.1
4.0±0.1
ꢀ
2.0±0.05
ꢀ
TRR03
TRR10
TRR18
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ ꢀ
0
+
ꢀ
MAX
Φ1.
4.0±0.1
4.01
2.0±0.05
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
0
ꢀ +0.1
ꢀ
ꢀ
ꢀ
ꢀ ꢀ
MAX
Φ15
ꢀ ꢀ
4.0±0.
ꢀ
.0±0.1
ꢀ
2.0±0.05
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ ꢀ
0
●Reel dimensions
(Unit : mm)
D
A
B
C
Part No.
TRR01
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
0
+1
+1.0
0
TRR03
TRR10
TRR18
Φ180
Φ60
9
Φ13±0.2
ꢀ
ꢀ
-1.5
0
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
www.rohm.com
c 2016 ROHMCo., Ltd.All rights reserved.
ꢀ
ꢀ
ꢀ ꢀ ꢀ ꢀ
4/4
2014.12 - Rev.C
Datasheet
Notice
Precaution on using ROHM Products
1.
(Note 1)
If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of
any ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
CLASSⅢ
CLASSⅣ
USA
EU
CLASSⅡb
CLASSⅢ
CHINA
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control systemHowever, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at yn responsibilities,
adequate safety measures including but not limited to fail-safe design against the phal injury, damage to any
property, which a failure or malfunction of our Products may cause. The followire examples of safety measures:
[a] Installation of protection circuits or other protective devices to imove stem safety
[b] Installation of redundant circuits to reduce the impact of single otiple circuit failure
3. Our Products are not designed under any special or extraordinary evironents or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable fr andamages, expenes r losses arising from
the use of any ROHM’s Products under any special or extraordinarenvironments onditions. If you intend to use
our Products under any special or extraordinary environmeor conditions (as explified below), your
independent verification and confirmation of product performce, reliability, etcrior o use, must be necessary:
[a] Use of our Products in any types of liquid, incudg water, oils, cheand organic solvents
[b] Use of our Products outdoors or in places whe the Products arexposed to direct sunlight or dust
[c] Use of our Products in places where the Pducts are exposed to sa wind or corrosive gases, including
Cl2, H2S, NH3, SO2, and NO2
[d] Use of our Products in places whrhe Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity o heat-producing conents, plastic cords, or other flammable items
[f] Sealing or coating our Prodwith resin or coatng materials
[g] Use of our Products withoaning residueven if you use no-clean type fluxes, cleaning residue
of flux is recommended); or Washing our Prodby using water or water-soluble cleaning agents for
cleaning residue afr sodering
[h] Use of the Prodts in places subject to dew condensation
4. The Products anot bject to radiation-prodesign.
5. Please verify cofirm characteriof the final or mounted products in using the Products.
6. In particular, if a transient load (large amount of load applied in a short period of time, such as pulse. is applied,
confition of performanhaeristics after on-board mounting is strongly recommended. Avoid applying power
exceedinnormal rated pow; exceeding the power rating under steady-state loading condition may negatively
roduct performance and reliability.
7De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the
actual ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined
in this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect
product performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Notice-PAA-E
Rev.001
c 2016 ROHMCo., Ltd.All rights reserved.
Datasheet
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
PrecautionsRegardingApplication Examplesand External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of
the characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this
document are presented only as guidance for Products use. Therefore, in case you use such information, you are
solely responsible for it and you must exercise your own independent verification and judgment in the use of such
information contained in this document. ROHM shall not be in any way responsible or liable for any damages,
expenses or losses incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discrgee take
proper caution in your manufacturing process and storage so that voltage exceeding the Productaximum rating will
not be applied to Products. Please take special care under dry condition (e.g. Grounding of human bdy / equipment /
solder iron, isolation from charged objects, setting of Ionizer, friction prevention and tempeure / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including , H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by RO
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability products out of recommended storage time
period may be degraded. It is strongly recommended to confsolderability before siProducts of which
storage time is exceeding the recommended storage time iod
3. Store / transport cartons in the correct direction, whiciindicated on a cara symbol. Otherwise bent
leads may occur due to excessive stress applied whdropping of a carton.
4. Use Products within the specified time after openia humidity barrier bag. Baking is required before using
Products of which storage time is exceeding threcommended stoge me period.
Precaution for Product Label
QR code printed on ROHM Products label is fROHM’s internal oly.
Precaution for Disposition
When disposing Products please dispose them properly usauthorized industry waste company.
Precaution for Foreign ExchanganForeign Trade act
Since concerned goods migbe fallen under listed itms of export control prescribed by Foreign exchange and
Foreigntrade act, please csulwith ROHM in ce export.
Precaution Regarntellectual Property Righs
1. All informationd data including bot limited to application example contained in this document is for
reference only. ROHM does nowarrt that foregoing information or data will not infringe any intellectual property
rights any other rights oany d party regarding such information or data.
2. ROHM sll not have any obgations where the claims, actions or demands arising from the combination of the
ts with other articles such as components, circuits, systems or external equipment (including software).
3No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM
r any third parties with respect to the Products or the information contained in this document. Provided, however,
that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent
necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior
written consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in
the Products or this document for any military purposes, including but not limited to, the development of
mass-destruction weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks
of ROHM, its affiliated companies or third parties.
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Notice-PAA-E
Rev.001
c 2016 ROHMCo., Ltd.All rights reserved.
Datasheet
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising form the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document not is current as of the issuing date and subject to change without any
prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM
sales representative.
3. The information contained in this document is provided on an “as in” basis and ROHM does not warrant tt all
information contained in this document is accurate and/or error-free. ROHM shall not be in any wponsible or
liable for any damages, expenses or losses incurred by you or third parties resulting form inuraor errors of
or concerning such information.
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Notice – WE
Rev.001
c 2016 ROHMCo., Ltd.All rights reserved.
相关型号:
TRR01MZPF2492
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 24900ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF2872
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 28700ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF2942
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 29400ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF3092
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 30900ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF3570
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 357ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF4121
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 4120ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF4990
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 499ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF4993
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 499000ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF49R9
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 49.9ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF5760
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 576ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF6340
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 634ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
TRR01MZPF6342
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 63400ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明