UCR03EVPFLR100 [ROHM]

Fixed Resistor, Metal Glaze/thick Film, 0.25W, 0.1ohm, 1% +/-Tol, 150ppm/Cel, Surface Mount, 0603, CHIP;


型号：	UCR03EVPFLR100
厂家：	ROHM
描述：	Fixed Resistor, Metal Glaze/thick Film, 0.25W, 0.1ohm, 1% +/-Tol, 150ppm/Cel, Surface Mount, 0603, CHIP 电阻器
文件：	总8页 (文件大小：547K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Thick film low ohmic chip resistors for current detection

UCR series

Datasheet

●

Features

1)Very-low ohmic resistance from 11mΩ is in lineup by thick-film resistive element.

2)Resistive element is located at bottom side, which reduces the resistance shift

during mounting process.

3)ROHM's unique structure achieved improvement of heat.

4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.

5)Corresponds toAEC-Q200. But UCR006 is preraring.

UCR03 (under 100mΩ or less) are unsupprted.

●

Products list

Operating

temperature

range

Size

RatedPower Resistance

Temperature

coefficient

Resistance range

(Ω)

Part No.

(70℃)

tolerance

(mm)

0603

(inch)

0201

(W)

(%)

(ppm/ ℃)

0～+300

(℃)

F( ±1%)

J( ±5%)

UCR006

UCR01

0.1

0.100≦R<1

(E24series)

-55～+155

0～300

0～250

0～200

0～250

0～200

0～150

0.068≦R<0.100 (E24series)

0.100≦R<0.220 (E24series)

0.220≦R≦0.910 (E24series)

0.020≦R<0.050 (E24series)

0.050≦R<0.100 (E24series)

0.100≦R<0.200 (E24series)

F( ±1%)

J( ±5%)

1005

1608

0402

0603

0.125

-55～+155

F( ±1%)

J( ±5%)

0.25

0.20

UCR03

F( ±1%)

J( ±5%)

0～150

0.220≦R≦0.910 (E24series)

0.020≦R≦0.047 (E24series)

0～250

0～150

250±200

0～250

0～150

F( ±1%)

J( ±5%)

(E24series)

0.047＜R＜0.1

0.011≦R＜0.020

UCR10

UCR18

2012

3216

0805

1206

0.33

-55～+155

0.020≦R≦0.047 (E24series)

0.047＜R＜0.1 (E24series)

0.011≦R<0.020 (E24series)

0～350

0～200

0～150

F( ±1%)

J( ±5%)

0.5

(E24series)

0.020≦R≦0.039

0.039＜R＜0.1

* Design and specifications are subject to change without notice.

Carefullycheck the specification sheetsupplied with the product before using or ordering it.

●

Part Number Description

U C R

1 0

E V H

R 1 0

Part No.

Size(mm[inch])

006 (0603 [0201])

01 (1005 [0402])

03 (1608 [0603])

10 (2012 [0805])

18 (3216 [1206])

Packagingspecifications code

Packaging

Nominal resistance

Resistance code,3 or 4 digits.

Resistance

Resistance Special

tolerance

part code

Quantity

Part No.

UCR006

UCR01

Code

YVP

MVP

specifications / Reel

UCR

F ( ±1%)

J ( ±5%)

S：0.011 ～

0.091Ω

L：0.1Ω

tolerance

(Thick film low

ohmic chip

resistors)

Resistance

code

Paper tape

15,000

Specialcode

(2mmPitch)

FS,FL,JS

：

4 digits

3 digits

Paper tape

10,000

(2mmPitch)

：

EWP

(20mΩ～47mΩ)

Paper tape

5,000

UCR03

(4mmPitch)

EVP

(51mΩ～910mΩ)

Paper tape

5,000

UCR10

UCR18

EVH

(4mmPitch)

Paper tape

5,000

(4mmPitch)

www.rohm.com

1/4

2015.01 - Rev.E

UCR series

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

Datasheet

●Chip resistor dimensions and markings

■UCR006/01

■UCR03(20mΩ≦R<50mΩ) ■UCR10/18

■UCR03(50mΩ≦R≦910mΩ)

There are three or four digits used for

the calculation number according to

IEC code and “R”is used for the

decimal point.

Ex.) 4digits······0.1Ω =R100

3digits······0.1Ω =R10

(Unit:mm)

Marking

Part No.

(mm)

0603

(inch)

0201

existence

ꢀ

UCR006

0.62±0.05

0.32±0.05

0.24±0.05

0.18±0.10

0.22±0.10

ꢀ ꢀ ꢀ

ꢀ

UCR01

UCR03

UCR10

UCR18

1005

1608

2012

3216

0402

0603

0805

1206

1.00±0.10

0.55±0.10

0.37±0.05

0.28±0.10

0.34±0.10

ꢀ ꢀ ꢀ

ꢀ

1.60±0.10

0.87±0.10

±0.50±0.10

0.45±0.20

ꢀ ꢀ ꢀ

ꢀ

2.00±0.10

1.25±0.10

0.55±0.10

0.24±0.20

0.50±0.20

Yes

ꢀ ꢀ ꢀ

ꢀ

3.20±0.15

1.60±0.15

0.55±0.10

0.30±0.20

0.90±0.25

ꢀ ꢀ ꢀ

●Land pattern example

(Unit:mm)

Dimensions

Part No.

UCR006

UCR01

UCR03

UCR10

UCR18

0.3

0.5

0.8

1.4

1.2

1.8

2.5

3.4

4.0

0.5

0.9

1.3

1.8

0.45

0.65

1.0

1.3

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

www.rohm.com

2/4

2015.01 - Rev.E

UCR series ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

Datasheet

●Derating curve

When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.

■UCR006/01/03/10/18

●Characteristics (UCR01/03/10/18)

Guaranteed value

Resistor type

Test items

Test conditions

20℃

Measuring method : Measure Bottom termination

by4 proves.

Resistance

See P.1

Variation of resistance

with temperature

See P.1

Measurement：+25/-55, +25/+125℃

Rated voltage(current)×2.5， 2

Overload

±(2.0％＋0.005Ω)

Anew uniform coating of minimum

of 95%of the surface being

immersed and no soldering

damage.

Rosin-ethanol solution25%(Wweight)

Soldering condition：245±5℃

Duration of immersion：2.0±0.5s

Solderability

ꢀ

±(1.0％＋0.005Ω)

Soldering condition：260±5℃

Resistance to

soldering heat

No remarkable abnormalityon the appearance. Duration of immersion：10±1s

Rapid change of

temperature

±(1.0％＋0.005Ω)

±(3.0％＋0.005Ω)

Test temp：-55℃～+125℃ 5cycle

40℃，93％(Relative humidity)

Test time：1,000h

Damp heat, steadystate

70℃,Rated voltage

1.5h:ON－0.5h:OFF

Test time：1,000h

Endurance at 70℃

±(3.0％＋0.005Ω)

155℃

Test time：1,000h

Endurance

±(3.0％＋0.005)

±(0.5％＋0.005Ω)

Without open.

23±5℃, Immersion cleaning, 5±0.5min

Solvent: 2-propanol

Resistance to solvent

Bend strength of

the end face plating

*Pleasecontact us for guaranteeof thetest conditions other thanthosedescribedabove.

Compliance Standard(s) : IEC60115-8

JISC 5201-8

www.rohm.com

3/4

2015.01 - Rev.E

UCR series

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

Datasheet

(Unit : mm)

ꢀ

●Tape dimensions

■Paper tape

Part No.

ꢀ

8.0±0.3

3.5±0.05

1.75±0.1

0.39±0.1

0.7±0.1

UCR006

ꢀ

8.0±0.3

ꢀ

3.5±0.05

ꢀ

1.75±0.1

0.7±0.1

ꢀ

1.2±0.10

ꢀ

UCR01

UCR03

UCR10

UCR18

ꢀ

8.0±0.3

ꢀ

3.5±0.05

ꢀ

1.75±0.1

1.1±0.1

ꢀ

1.9±0.1

ꢀ

+0.2

ꢀ

+0.2

8.0±0.3

ꢀ

3.5±0.05

ꢀ

1.75±0.1

1.65

2.4

ꢀ

-0.1

ꢀ

+0.1

+0.15

8.0±0.3

ꢀ

3.5±0.05

ꢀ

1.75±0.1

1.95

3.5

ꢀ

-0.05

+0.1

Part No.

ꢀ

MAX

Φ1.5

4.0±0.1

2.0±0.05

0.46

1.1

UCR006

ꢀ

+0.1

ꢀ

ꢀ ꢀ

MAX

Φ1.5

4.0±0.1

ꢀ

2.0±0.05

ꢀ

2.0±0.05

ꢀ

UCR01

UCR03

UCR10

UCR18

ꢀ

ꢀ ꢀ

ꢀ

+0.1

ꢀ

ꢀ ꢀ

MAX

Φ1.5

4.0±0.1

ꢀ

4.0±0.05

ꢀ

2.0±0.05

ꢀ

ꢀ ꢀ

ꢀ

+0.1

ꢀ

ꢀ ꢀ

MAX

Φ1.5

4.0±0.1

ꢀ

4.0±0.1

ꢀ

2.0±0.05

ꢀ

ꢀ ꢀ

+0.1

ꢀ

MAX

Φ1.5

4.0±0.1

ꢀ

4.0±0.1

ꢀ

2.0±0.05

ꢀ

ꢀ ꢀ

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

ꢀ

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

●Reel dimensions

(Unit : mm)

Part No.

UCR006

ꢀ

UCR01

UCR03

UCR10

UCR18

+1.0

ꢀ

+1.0

Φ180

Φ60

Φ13±0.2

-1.5

ꢀ

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

www.rohm.com

ꢀ

ꢀ ꢀ ꢀ ꢀ ^ꢀ

4/4

2015.01 - Rev.E

Datasheet

Notice

Precaution on using ROHM Products

(Note1)

If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment

aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,

bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales

representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of

any ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

CLASSⅢ

CLASSⅣ

USA

CLASSⅡb

CLASSⅢ

CHINA

CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities,

adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any

property, which a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.

Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from

the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use

our Products under any special or extraordinary environments or conditions (as exemplified below), your

independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including

Cl2, H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue

of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for

cleaning residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively

affect product performance and reliability.

7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the

actual ambient temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined

in this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect

product performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

ꢀ

Notice-PAA-E

Rev.001

Datasheet

ꢀ

PrecautionsRegardingApplication Examplesand External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of

the characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this

document are presented only as guidance for Products use. Therefore, in case you use such information, you are

solely responsible for it and you must exercise your own independent verification and judgment in the use of such

information contained in this document. ROHM shall not be in any way responsible or liable for any damages,

expenses or losses incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take

proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will

not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment /

solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time

period may be degraded. It is strongly recommended to confirm solderability before using Products of which

storage time is exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent

leads may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using

Products of which storage time is exceeding the recommended storage time period.

Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and

Foreigntrade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for

reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property

rights or any other rights of any third party regarding such information or data.

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the

Products with other articles such as components, circuits, systems or external equipment (including software).

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM

or any third parties with respect to the Products or the information contained in this document. Provided, however,

that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent

necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior

written consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in

the Products or this document for any military purposes, including but not limited to, the development of

mass-destruction weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks

of ROHM, its affiliated companies or third parties.

Notice-PAA-E

Rev.001

Datasheet

General Precaution

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising form the use of any

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this document not is current as of the issuing date and subject to change without any

prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM

sales representative.

3. The information contained in this document is provided on an “as in” basis and ROHM does not warrant that all

information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting form inaccuracy or errors of

or concerning such information.

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

ꢀ

ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ

Notice – WE

Rev.001

Datasheet

Buy

UCR10EVHJS - Web Page

Distribution Inventory

Part Number

Package

Unit Quantity

UCR10EVHJS

5000

Minimum Package Quantity

Packing Type

Constitution Materials List

RoHS

5000

Taping

inquiry

Yes

UCR03EVPFLR100 [ROHM]

相关型号：

UCR03EVPFS

UCR03EVPFSFL

UCR03EVPFSFS

UCR03EVPFSJL

UCR03EVPFSJS

UCR03EVPJL

UCR03EVPJLFL

UCR03EVPJLFS

UCR03EVPJLJL

UCR03EVPJLJS

UCR03EVPJS

UCR03EVPJSFL