K7R161884B-EC300 [SAMSUNG]
QDR SRAM, 1MX18, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FBGA-165;型号: | K7R161884B-EC300 |
厂家: | SAMSUNG |
描述: | QDR SRAM, 1MX18, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FBGA-165 时钟 静态存储器 内存集成电路 |
文件: | 总19页 (文件大小:451K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
18Mb QDRII SRAM Specification
165FBGA with Pb & Pb-Free
(RoHS compliant)
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE,
TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOLOGY.
ALL INFORMATION IN THIS DOCUMENT IS PROVIDED
ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or simi-
lar applications where Product failure could result in loss of life or personal or physical harm, or any military
or defense application, or any governmental procurement to which special terms or provisions may apply.
* Samsung Electronics reserves the right to change products or specification without notice.
Rev. 5.0 July 2006
- 1 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
Document Title
512Kx36-bit,1Mx18-bit QDRTM II b4 SRAM
Revision History
Draft Date
Remark
Advance
Preliminary
Rev. No.
History
Oct. 17. 2002
Dec. 16, 2002
0.0
1. Initial document.
0.1
1. Change the Boundary scan exit order.
2. Correct the Overshoot and Undershoot timing diagram.
Preliminary
Preliminary
Preliminary
Dec. 26, 2002
Jan. 27, 2003
Mar. 20, 2003
0.2
0.3
0.4
1. Change JTAG Block diagram
1. Add the speed bin (-25)
1. Correct the JTAG ID register definition
2. Correct the AC timing parameter (delete the tKHKH Max value)
Preliminary
Preliminary
April. 4, 2003
0.5
0.6
1. Change the Maximum Clock cycle time.
2. Correct the 165FBGA package ball size.
June. 20, 2003
1. Add the power up/down sequencing comment.
2. Update the DC current parameter (Icc and Isb).
3. Change the Max. speed bin from -33 to -30.
Preliminary
Oct. 20. 2003
0.7
1. Change the ISB1.
Speed Bin
From
To
-30
-25
-20
-16
200
180
160
140
230
210
190
170
Final
Final
Oct. 31, 2003
Nov. 28, 2003
1.0
2.0
1. Final spec release
1. Delete the x8 Org.
2. Delete the 300MHz speed bin
Final
Final
Final
Nov. 10. 2004
Mar. 29. 2006
Jul. 26 2006
3.0
4.0
5.0
1. Add the Industrial temp. & Lead Free Package
1. Add the 300MHz speed bin
1. Change Vss/SA to NC/SA in Pin Configuration
The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the
specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions on the parameters of this device. If you have any ques-
tions, please contact the SAMSUNG branch office near your office, call or contact Headquarters.
Rev. 5.0 July 2006
- 2 -
K7R163684B
K7R161884B
512Kx36-bit, 1Mx18-bit QDR II b4 SRAM
512Kx36 & 1Mx18 QDRTM II b4 SRAM
TM
FEATURES
• 1.8V+0.1V/-0.1V Power Supply.
Part
Cycle Access
Time Time
• DLL circuitry for wide output data valid window and future fre-
quency scaling.
Organization
Unit
Number
• I/O Supply Voltage 1.5V+0.1V/-0.1V for 1.5V I/O,
1.8V+0.1V/-0.1V for 1.8V I/O.
• Separate independent read and write data ports
with concurrent read and write operation
• HSTL I/O
• Full data coherency, providing most current data.
• Synchronous pipeline read with self timed late write.
• Registered address, control and data input/output.
• DDR (Double Data Rate) Interface on read and write ports.
• Fixed 4-bit burst for both read and write operation.
• Clock-stop supports to reduce current.
• Two input clocks (K and K) for accurate DDR timing at clock
rising edges only.
K7R163684B-E(F)C(I)30 3.3
K7R163684B-E(F)C(I)25 4.0
K7R163684B-E(F)C(I)20 5.0
K7R163684B-E(F)C(I)16 6.0
K7R161884B-E(F)C(I)30 3.3
K7R161884B-E(F)C(I)25 4.0
K7R161884B-E(F)C(I)20 5.0
K7R161884B-E(F)C(I)16 6.0
0.45
0.45
0.45
0.50
0.45
0.45
0.45
0.50
ns
ns
ns
ns
ns
ns
ns
ns
X36
X18
* -E(F)C(I)
E(F) [Package type] : E-Pb Free, F-Pb
C(I) [Operating Temperature] : C-Commercial, I-Industrial
• Two input clocks for output data (C and C) to minimize
clock-skew and flight-time mismatches.
• Two echo clocks (CQ and CQ) to enhance output data
traceability.
• Single address bus.
• Byte write (x18, x36) function.
• Separate read/write control pin(R and W)
• Simple depth expansion with no data contention.
• Programmable output impedance.
• JTAG 1149.1 compatible test access port.
• 165FBGA(11x15 ball array) with body size of 13mmx15mm.
& Lead Free
• Operating in commercial and industrial temperature range.
FUNCTIONAL BLOCK DIAGRAM
36 (or 18)
DATA
REG
D(Data in)
72(or 36)
72(or 36)
WRITE DRIVER
17
17 (or 18)
(or 18)
ADD
REG
ADDRESS
R
W
BWX
72
144
512Kx36
(1Mx18)
MEMORY
ARRAY
(or 36)
36 (or 18)
(or 72)
CTRL
Q(Data Out)
LOGIC
72
4 (or 2)
CQ, CQ
(or 36)
(Echo Clock out)
K
K
CLK
GEN
C
C
SELECT OUTPUT CONTROL
Notes: 1. Numbers in ( ) are for x18 device
QDR SRAM and Quad Data Rate comprise a new family of products developed by Cypress, Hitachi, IDT, Micron, NEC and Samsung technology.
Rev. 5.0 July 2006
- 3 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
PIN CONFIGURATIONS(TOP VIEW) K7R163684B(512Kx36)
1
2
NC/SA*
Q18
Q28
D20
D29
Q21
D22
VREF
Q31
D32
Q24
Q34
D26
D35
TCK
3
NC/SA*
D18
D19
Q19
Q20
D21
Q22
VDDQ
D23
Q23
D24
D25
Q25
Q26
SA
4
5
6
7
8
9
NC/SA*
D17
D16
Q16
Q15
D14
Q13
VDDQ
D12
Q12
D11
D10
Q10
Q9
10
NC/SA*
Q17
Q7
11
CQ
Q8
D8
D7
Q6
Q5
D5
ZQ
D4
Q3
Q2
D2
D1
Q0
TDI
A
B
C
D
E
F
CQ
W
BW2
BW3
SA
K
BW1
BW0
SA
R
Q27
D27
D28
Q29
Q30
D30
Doff
D31
Q32
Q33
D33
D34
Q35
TDO
SA
K
SA
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
SA
NC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
SA
C
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
SA
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
SA
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
SA
D15
D6
Q14
D13
VREF
Q4
G
H
J
K
L
D3
Q11
Q1
M
N
P
R
D9
SA
SA
D0
SA
SA
C
SA
SA
SA
TMS
Notes : 1. * Checked No Connect (NC) pins are reserved for higher density address, i.e. 9A for 32Mb, 3A for 72Mb, 10A for 144Mb and 2A for 288Mb.
2. BW0 controls write to D0:D8, BW1 controls write to D9:D17, BW2 controls write to D18:D26 and BW3 controls write to D27:D35.
PIN NAME
SYMBOL
K, K
PIN NUMBERS
DESCRIPTION
Input Clock
NOTE
6B, 6A
C, C
CQ, CQ
Doff
6P, 6R
11A, 1A
1H
Input Clock for Output Data
Output Echo Clock
DLL Disable when low
Address Inputs
1
SA
4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R
10P,11N,11M,10K,11J,11G,10E,11D,11C,10N,9M,9L
9J,10G,9F,10D,9C,9B,3B,3C,2D,3F,2G,3J,3L,3M,2N
1C,1D,2E,1G,1J,2K,1M,1N,2P
D0-35
Data Inputs
11P,10M,11L,11K,10J,11F,11E,10C,11B,9P,9N,10L
9K,9G,10F,9E,9D,10B,2B,3D,3E,2F,3G,3K,2L,3N
3P,1B,2C,1E,1F,2J,1K,1L,2M,1P
Q0-35
Data Outputs
W
R
4A
8A
Write Control Pin, active when low
Read Control Pin, active when low
Block Write Control Pin, active when low
Input Reference Voltage
Output Driver Impedance Control Input
Power Supply (1.8 V)
BW0, BW1,BW2, BW3
7B,7A,5A,5B
2H,10H
VREF
ZQ
VDD
VDDQ
VSS
11H
2
3
5F,7F,5G,7G,5H,7H,5J,7J,5K,7K
4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L
4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M, 8M,4N,8N
Output Power Supply (1.5V or 1.8V)
Ground
TMS
TDI
TCK
TDO
NC
10R
11R
2R
1R
JTAG Test Mode Select
JTAG Test Data Input
JTAG Test Clock
JTAG Test Data Output
No Connect
2A,3A,10A,6C,9A
Notes: 1. C, C, K or K cannot be set to VREF voltage.
2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected
3. Not connected to chip pad internally.
.
Rev. 5.0 July 2006
- 4 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
PIN CONFIGURATIONS(TOP VIEW) K7R161884B(1Mx18)
1
2
NC/SA*
Q9
3
NC/SA*
D9
4
5
6
7
8
9
SA
10
NC/SA*
NC
11
CQ
Q8
D8
D7
Q6
Q5
D5
ZQ
D4
Q3
Q2
D2
D1
Q0
TDI
A
B
C
D
E
F
CQ
NC
NC
NC
NC
NC
NC
Doff
NC
NC
NC
NC
NC
NC
TDO
W
BW1
NC
K
NC
R
SA
K
BW0
SA
SA
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
SA
NC
D10
Q10
Q11
D12
Q13
VDDQ
D14
Q14
D15
D16
Q16
Q17
SA
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
SA
SA
NC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
SA
C
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
SA
Q7
D11
NC
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
SA
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
SA
NC
D6
Q12
D13
VREF
NC
NC
G
H
J
NC
VREF
Q4
K
L
NC
D3
Q15
NC
NC
M
N
P
R
Q1
D17
NC
NC
SA
SA
D0
TCK
SA
SA
C
SA
SA
TMS
Notes: 1. * Checked No Connect (NC) pins are reserved for higher density address, i.e. 3A for 36Mb, 10A for 72Mb and 2A for 144Mb.
2. BW0 controls write to D0:D8 and BW1 controls write to D9:D17.
PIN NAME
SYMBOL
K, K
PIN NUMBERS
DESCRIPTION
Input Clock
NOTE
6B, 6A
C, C
CQ, CQ
Doff
6P, 6R
11A, 1A
1H
Input Clock for Output Data
Output Echo Clock
DLL Disable when low
Address Inputs
1
SA
9A,4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R
10P,11N,11M,10K,11J,11G,10E,11D,11C,3B,3C,2D
3F,2G,3J,3L,3M,2N
D0-17
Data Inputs
11P,10M,11L,11K,10J,11F,11E,10C,11B,2B,3D,3E
2F,3G,3K,2L,3N,3P
Q0-17
Data Outputs
W
R
4A
8A
7B, 5A
2H,10H
11H
Write Control Pin, active when low
Read Control Pin, active when low
Block Write Control Pin, active when low
Input Reference Voltage
Output Driver Impedance Control Input
Power Supply (1.8 V)
BW0, BW1
VREF
ZQ
2
VDD
5F,7F,5G,7G,5H,7H,5J,7J,5K,7K
VDDQ
VSS
4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L
Output Power Supply (1.5V or 1.8V)
Ground
4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M-8M,4N,8N
TMS
TDI
TCK
TDO
10R
11R
2R
JTAG Test Mode Select
JTAG Test Data Input
JTAG Test Clock
1R
JTAG Test Data Output
2A,3A,10A,7A,1B,5B,9B,10B,1C,2C,6C,9C,1D,9D,10D,1E,2E,9E,
1F,9F,10F,1G,9G,10G,1J,2J,9J,1K,2K,9K,1L,9L,10L,1M
2M,9M,1N,9N,10N,1P,2P,9P
NC
No Connect
3
Notes: 1. C, C, K or K cannot be set to VREF voltage.
2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected
3. Not connected to chip pad internally.
.
Rev. 5.0 July 2006
- 5 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
GENERAL DESCRIPTION
The K7R163684B and K7R161884B are 18,874,368-bits QDR (Quad Data Rate)
Synchronous Pipelined Burst SRAMs.
They are organized as 524,288 words by 36bits for K7R163684B and 1,048,576 words by 18 bits for K7R161884B.
The QDR operation is possible by supporting DDR read and write operations through separate data output and input ports
with the same cycle. Memory bandwidth is maximized as data can be transferred into SRAM
on every rising edge of K and K, and transferred out of SRAM on every rising edge of C and C.
And totally independent read and write ports eliminate the need for high speed bus turn around.
Address for read and write are latched on alternate rising edges of the input clock K.
Data inputs, and all control signals are synchronized to the input clock (K or K).
Normally data outputs are synchronized to output clocks (C and C), but when C and C are tied high,
the data outputs are synchronized to the input clocks (K and K).
Read data are referenced to echo clock (CQ or CQ) outputs.
Common address bus is used to access address both for read and write operations.
The internal burst counter is fixed to 4-bit sequential for both read and write operations, requiring tow full clock bus cycles.
Any request that attempts to interrupt a burst operation in progress is ignored.
Synchronous pipeline read and late write enable high speed operations.
Simple depth expansion is accomplished by using R and W for port selection.
Byte write operation is supported with BW0 and BW1 (BW2 and BW3) pins.
Nibble write operation is supported with NW0 and NW1 pins for x8 device.
IEEE 1149.1 serial boundary scan (JTAG) simplifies monitoring package pads attachment status with system.
The K7R163684B and K7R161884B are implemented with SAMSUNG's high performance 6T CMOS technology
and is available in 165pin FBGA packages. Multiple power and ground pins minimize ground bounce.
READ OPERATIONS
Read cycles are initiated by activating R at the rising edge of the positive input clock K.
Address is presented and stored in the read address register synchronized with K clock.
For 4-bit burst DDR operation, it will access four 36-bit or 18-bit or 8-bit data words with each read command.
The first pipelined data is transferred out of the device triggered by C clock following next K clock rising edge.
Next burst data is triggered by the rising edge of following C clock rising edge.
The process continues until all four data are transferred.
Continuous read operations are initiated with K clock rising edge.
And pipelined data are transferred out of device on every rising edge of both C and C clocks.
In case C and C tied to high, output data are triggered by K and K instead of C and C.
When the R is disabled after a read operation, the K7R163684B and K7R161884B will first complete
burst read operation
before entering into deselect mode at the next K clock rising edge.
Then output drivers disabled automatically to high impedance state.
ECHO CLOCK OPERATION
To assure the output traceability, the SRAM provides the output Echo clock, pair of compliment clock CQ and CQ,
which are synchronized with internal data output.
Echo clocks run free during normal operation.
The Echo clock is triggered by internal output clock signal, and transferred to external through same structures
as output driver.
Rev. 5.0 July 2006
- 6 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
WRITE OPERATIONS
Write cycles are initiated by activating W at the rising edge of the positive input clock K.
Address is presented and stored in the write address register synchronized with K clock.
For 4-bit burst DDR operation, it will write four 36-bit or 18-bit or 8-bit data words with each write command.
The first “late” data is transferred and registered in to the device synchronous with next K clock rising edge.
Next burst data is transferred and registered synchronous with following K clock rising edge.
The process continues until all four data are transferred and registered.
Continuous write operations are initiated with K rising edge.
And “late writed” data is presented to the device on every rising edge of both K and K clocks.
The device disregards input data presented on the same cycle W disabled.
When the W is disabled after a read operation, the K7R163684B and K7R161884B will first complete
burst read operation before entering into deselect mode at the next K clock rising edge.
The K7R163684B and K7R161884B support byte write operations.
With activating BW0 or BW1 (BW2 or BW3) in write cycle, only one byte of input data is presented.
In K7R161884B, BW0 controls write operation to D0:D8, BW1 controls write operation to D9:D17.
And in K7R163684B BW2 controls write operation to D18:D26, BW3 controls write operation to D27:D35.
PROGRAMMABLE IMPEDANCE OUTPUT BUFFER OPERATION
The designer can program the SRAM's output buffer impedance by terminating the ZQ pin to VSS through a precision resistor (RQ).
The value of RQ (within 15%) is five times the output impedance desired.
For example, 250Ω resistor will give an output impedance of 50Ω.
Impedance updates occur early in cycles that do not activate the outputs, such as deselect cycles.
In all cases impedance updates are transparent to the user and do not produce access time “push-outs”
or other anomalous behavior in the SRAM.
There are no power up requirements for the SRAM. However, to guarantee optimum output driver impedance after power up,
the SRAM needs 1024 non-read cycles.
SINGLE CLOCK MODE
The K7R163684B and K7R161884B can be operated with the single clock pair K and K,
instead of C or C for output clocks.
To operate these devices in single clock mode, C and C must be tied high during power up and must be maintained high
during operation.
After power up, this device can’t change to or from single clock mode.
System flight time and clock skew could not be compensated in this mode.
DEPTH EXPANSION
Separate input and output ports enables easy depth expansion.
Each port can be selected and deselected independently
and read and write operation do not affect each other.
Before chip deselected, all read and write pending operations are completed.
POWER-UP/POWER-DOWN SUPPLY VOLTAGE SEQUENCING
The following power-up supply voltage application is recommended: VSS, VDD, VDDQ, VREF, then VIN. VDD and VDDQ can be applied
simultaneously, as long as VDDQ does not exceed VDD by more than 0.5V during power-up. The following power-down supply voltage
removal sequence is recommended: VIN, VREF, VDDQ, VDD, VSS. VDD and VDDQ can be removed simultaneously, as long as VDDQ
does not exceed VDD by more than 0.5V during power-down.
Rev. 5.0 July 2006
- 7 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
STATE DIAGRAM
POWER-UP
READ
WRITE
READ NOP
WRITE NOP
WRITE
READ
READ
WRITE
LOAD NEW
READ ADDRESS
D count=0
LOAD NEW
WRITE ADDRESS
D count=0
D count=2
D count=2
WRITE
D count=2
READ
D count=2
ALWAYS
ALWAYS
DDR READ
D count=D count+1
DDR WRITE
D count=D count+1
READ
WRITE
ALWAYS
ALWAYS
D count=1
D count=1
INCREMENT
INCREMENT
READ ADDRESS
WRITE ADDRESS
Notes: 1. Internal burst counter is fixed as 2-bit linear, i.e. when first address is A0+0, next internal burst address is A0+1.
2. “READ” refers to read active status with R=Low, “READ” refers to read inactive status with R=high. “WRITE” and "WRITE" are the same case.
3. Read and write state machine can be active simultaneously.
4. State machine control timing sequence is controlled by K.
Rev. 5.0 July 2006
- 8 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
TRUTH TABLES
SYNCHRONOUS TRUTH TABLE
D
Q
K
R
W
OPERATION
D(A1)
D(A2)
D(A3)
D(A4)
Q(A1)
Q(A2)
Q(A3)
Q(A4)
Previous Previous Previous Previous Previous Previous Previous Previous
Stopped
X
H
X
H
X
Clock Stop
state
state
state
state
state
High-Z
DOUT
state
High-Z
DOUT
state
High-Z
DOUT
state
↑
↑
X
X
X
X
High-Z No Operation
DOUT
Read
L4
X
X
X
X
at C(t+1) at C(t+2) at C(t+2) at C(t+3)
Din
Din
Din
Din
H5
L4
↑
X
X
X
X
Write
at K(t+1) at K(t+1) at K(t+2) at K(t+2)
Notes: 1. X means “Don′t Care”.
2. The rising edge of clock is symbolized by ( ↑ ).
3. Before enter into clock stop status, all pending read and write operations will be completed.
4. This signal was HIGH on previous K clock rising edge. Initiating consecutive READ or WRITE operations on consecutive K clock rising edges
is not permitted. The device will ignore the second request.
5. If this signal was LOW to initiated the previous cycle, this signal becomes a don′t care for this operation however it is strongly recommended
that this signal is brought HIGH as shown in the truth table.
WRITE TRUTH TABLE(x18)
K
K
↑
↑
↑
↑
BW0
L
BW1
L
OPERATION
↑
WRITE ALL BYTEs ( K↑ )
WRITE ALL BYTEs ( K↑ )
WRITE BYTE 0 ( K↑ )
WRITE BYTE 0 ( K↑ )
WRITE BYTE 1 ( K↑ )
WRITE BYTE 1 ( K↑ )
WRITE NOTHING ( K↑ )
WRITE NOTHING ( K↑ )
L
L
↑
↑
↑
L
H
L
H
H
L
H
L
H
H
H
H
Notes: 1. X means “Don′t Care”.
2. All inputs in this table must meet setup and hold time around the rising edge of input clock K or K ( ↑ ).
3. Assumes a WRITE cycle was initiated.
4. This table illustrates operation for x18 devices.
WRITE TRUTH TABLE(x36)
K
K
↑
↑
↑
↑
↑
BW0
L
BW1
L
BW2
L
BW3
L
OPERATION
WRITE ALL BYTEs ( K↑ )
WRITE ALL BYTEs ( K↑ )
WRITE BYTE 0 ( K↑ )
↑
L
L
L
L
↑
↑
↑
↑
L
H
H
L
H
H
H
H
L
H
H
H
H
L
L
WRITE BYTE 0 ( K↑ )
H
H
H
H
H
H
WRITE BYTE 1 ( K↑ )
L
WRITE BYTE 1 ( K↑ )
H
H
H
H
WRITE BYTE 2 and BYTE 3 ( K↑ )
WRITE BYTE 2 and BYTE 3 ( K↑ )
WRITE NOTHING ( K↑ )
WRITE NOTHING ( K↑ )
L
L
H
H
H
H
Notes: 1. X means “Don′t Care”.
2. All inputs in this table must meet setup and hold time around the rising edge of input clock K or K ( ↑ ).
3. Assumes a WRITE cycle was initiated.
Rev. 5.0 July 2006
- 9 -
K7R163684B
K7R161884B
ABSOLUTE MAXIMUM RATINGS*
512Kx36 & 1Mx18 QDRTM II b4 SRAM
PARAMETER
Voltage on VDD Supply Relative to VSS
Voltage on VDDQ Supply Relative to VSS
Voltage on Input Pin Relative to VSS
Storage Temperature
SYMBOL
VDD
RATING
-0.5 to 2.9
-0.5 to VDD
-0.5 to VDD+0.3
-65 to 150
0 to 70
UNIT
V
VDDQ
VIN
V
V
TSTG
TOPR
TOPR
TBIAS
°C
°C
°C
°C
Commercial
Industrial
Operating Temperature
-40 to 85
Storage Temperature Range Under Bias
-10 to 85
*Note: 1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. VDDQ must not exceed VDD during normal operation.
DC ELECTRICAL CHARACTERISTICS(VDD=1.8V ±0.1V, TA=0°C to +70°C)
PARAMETER
Input Leakage Current
Output Leakage Current
SYMBOL
TEST CONDITIONS
VDD=Max ; VIN=VSS to VDDQ
Output Disabled,
MIN
MAX
+2
UNIT NOTE
µA
µA
IIL
-2
-2
-
IOL
+2
-30
-25
-20
-16
-30
-25
-20
-16
-30
-25
-20
-16
550
-
500
VDD=Max , IOUT=0mA
Cycle Time ≥ tKHKH Min
Operating Current
(x36) : DDR
ICC
ICC
mA
mA
mA
1,5
1,5
1,6
-
450
400
-
-
-
450
400
VDD=Max , IOUT=0mA
Cycle Time ≥ tKHKH Min
Operating Current
(x18) : DDR
350
300
-
230
Device deselected,
IOUT=0mA, f=Max,
All Inputs≤0.2V or ≥ VDD-0.2V
-
210
Standby Current(NOP): DDR
ISB1
-
190
-
170
Output High Voltage
Output Low Voltage
Output High Voltage
Output Low Voltage
Input Low Voltage
Input High Voltage
VOH1
VOL1
VOH2
VOL2
VIL
VDDQ/2-0.12
VDDQ/2-0.12
VDDQ-0.2
VSS
VDDQ/2+0.12
VDDQ/2+0.12
VDDQ
0.2
V
V
V
V
V
V
2,7
3,7
4
IOH=-1.0mA
IOL=1.0mA
4
-0.3
VREF-0.1
VDDQ+0.3
8,9
8,10
VIH
VREF+0.1
Notes: 1. Minimum cycle. IOUT=0mA.
2. |IOH|=(VDDQ/2)/(RQ/5)±15% for 175Ω ≤ RQ ≤ 350Ω.
3. |IOL|=(VDDQ/2)/(RQ/5)±15% for 175Ω ≤ RQ ≤ 350Ω.
4. Minimum Impedance Mode when ZQ pin is connected to VDDQ.
5. Operating current is calculated with 50% read cycles and 50% write cycles.
6. Standby Current is only after all pending read and write burst operations are completed.
7. Programmable Impedance Mode.
8. These are DC test criteria. DC design criteria is VREF±50mV. The AC VIH/VIL levels are defined separately for measuring
timing parameters.
9. VIL (Min) DC=-0.3V, VIL (Min) AC=-1.5V(pulse width ≤ 3ns).
10. VIH (Max)DC=VDDQ+0.3, VIH (Max)AC=VDDQ+0.85V(pulse width ≤ 3ns).
Rev. 5.0 July 2006
- 10 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
AC ELECTRICAL CHARACTERISTICS (VDD=1.8V ±0.1V, TA=0°C to +70°C)
PARAMETER
Input High Voltage
Input Low Voltage
SYMBOL
VIH (AC)
VIL (AC)
MIN
MAX
-
UNIT
V
NOTES
1,2
VREF + 0.2
-
VREF - 0.2
V
1,2
Notes: 1. This condition is for AC function test only, not for AC parameter test.
2. To maintain a valid level, the transition edge of the input must:
a) Sustain a constant slew rate from the current AC level through the target AC level, VIL(AC) or VIH(AC)
b) Reach at least the target AC level
c) After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC)
Overershoot Timing
Undershoot Timing
20% tKHKH(MIN)
VIH
VDDQ+0.5V
VDDQ+0.25V
VDDQ
VSS
VSS-0.25V
VSS-0.5V
20% tKHKH(MIN)
VIL
Note: For power-up, VIH ≤ VDDQ+0.3V and VDD ≤ 1.7V and VDDQ ≤ 1.4V t ≤ 200ms
OPERATING CONDITIONS (0°C ≤ TA ≤ 70°C)
PARAMETER
SYMBOL
VDD
MIN
1.7
1.4
0.68
0
MAX
1.9
1.9
0.95
0
UNIT
V
V
V
V
Supply Voltage
VDDQ
VREF
Reference Voltage
Ground
VSS
AC TEST CONDITIONS
Parameter
Core Power Supply Voltage
Output Power Supply Voltage
Input High/Low Level
Symbol
VDD
Value
1.7~1.9
1.4~1.9
1.25/0.25
0.75
Unit
V
AC TEST OUTPUT LOAD
VDDQ
VIH/VIL
VREF
V
0.75V
VREF
VDDQ/2
V
Input Reference Level
V
50Ω
SRAM
Zo=50Ω
Input Rise/Fall Time
TR/TF
0.3/0.3
VDDQ/2
ns
V
Output Timing Reference Level
250Ω
ZQ
Note: Parameters are tested with RQ=250Ω
Rev. 5.0 July 2006
- 11 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
AC TIMING CHARACTERISTICS(VDD=1.8V±0.1V, TA=0°C to +70°C)
-30
-25
-20
-16
PARAMETER
SYMBOL
UNIT NOTE
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
Clock
Clock Cycle Time (K, K, C, C)
Clock Phase Jitter (K, K, C, C)
Clock High Time (K, K, C, C)
Clock Low Time (K, K, C, C)
Clock to Clock (K↑ → K↑, C↑ → C↑)
Clock to data clock (K↑ → C↑, K↑→ C↑)
DLL Lock Time (K, C)
tKHKH
tKC var
tKHKL
3.30
8.40
0.20
4.00
8.40
0.20
5.00
8.40
0.20
6.00
8.40
0.20
ns
ns
ns
5
6
1.32
1.32
1.49
0.00
1024
30
1.60
1.60
1.80
0.00
1024
30
2.00
2.00
2.20
0.00
1024
30
2.40
2.40
2.70
0.00
1024
30
tKLKH
ns
tKHKH
tKHCH
tKC lock
tKC reset
ns
1.45
1.80
2.30
2.80
ns
cycle
ns
K Static to DLL reset
Output Times
C, C High to Output Valid
C, C High to Output Hold
C, C High to Echo Clock Valid
C, C High to Echo Clock Hold
CQ, CQ High to Output Valid
CQ, CQ High to Output Hold
C, High to Output High-Z
C, High to Output Low-Z
Setup Times
tCHQV
tCHQX
0.45
0.45
0.27
0.45
0.45
0.45
0.30
0.45
0.45
0.45
0.35
0.45
0.50
0.50
0.40
0.50
ns
ns
ns
ns
ns
ns
ns
ns
3
3
-0.45
-0.45
-0.27
-0.45
-0.45
-0.45
-0.30
-0.45
-0.45
-0.45
-0.35
-0.45
-0.50
-0.50
-0.40
-0.50
tCHCQV
tCHCQX
tCQHQV
tCQHQX
tCHQZ
7
7
3
3
tCHQX1
Address valid to K rising edge
Control inputs valid to K rising edge
Data-in valid to K, K rising edge
Hold Times
tAVKH
tIVKH
0.40
0.40
0.30
0.50
0.50
0.35
0.60
0.60
0.40
0.70
0.70
0.50
ns
ns
ns
2
tDVKH
K rising edge to address hold
K rising edge to control inputs hold
K, K rising edge to data-in hold
tKHAX
tKHIX
0.40
0.40
0.30
0.50
0.50
0.35
0.60
0.60
0.40
0.70
0.70
0.50
ns
ns
ns
tKHDX
Notes: 1. All address inputs must meet the specified setup and hold times for all latching clock edges.
2. Control signal are R and W.
In case of BW0,BW1 (BW2, BW3, also for x36) signal follow the data setup/hold times.
3. If C,C are tied high, K,K become the references for C,C timing parameters.
4. To avoid bus contention, at a given voltage and temperature tCHQX1 is bigger than tCHQZ.
The specs as shown do not imply bus contention because tCHQX1 is a MIN parameter that is worst case at totally different test conditions
(0°C, 1.9V) than tCHQZ, which is a MAX parameter (worst case at 70°C, 1.7V)
It is not possible for two SRAMs on the same board to be at such different voltage and temperature.
5. Clock phase jitter is the variance from clock rising edge to the next expected clock rising edge.
6. Vdd slew rate must be less than 0.1V DC per 50 ns for DLL lock retention. DLL lock time begins once Vdd and input clock are stable.
Rev. 5.0 July 2006
- 12 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
PIN CAPACITANCE
PRMETER
Address Control Input Capacitance
Input and Output Capacitance
Clock Capacitance
SYMBOL
CIN
TESTCONDITION
TYP
MAX
Unit
pF
NOTES
VIN=0V
VOUT=0V
-
4
6
5
5
7
6
COUT
pF
CCLK
pF
Note: 1. Parameters are tested with RQ=250Ω and VDDQ=1.5V.
2. Periodically sampled and not 100% tested.
THERMAL RESISTANCE
PRMETER
Junction to Ambient
Junction to Case
SYMBOL
TYP
17.1
3.3
Unit
NOTES
θJA
°C/W
°C/W
θJC
Note: Junction temperature is a function of on-chip power dissipation, package thermal impedance, mounting site temperature and mounting site
thermal impedance. TJ=TA + PD x θJA
APPLICATION INFORMATION
R=250Ω
R=250Ω
ZQ
ZQ
SRAM#1
SRAM#4
CQ
CQ
Q
CQ
CQ
Q
Vt
D
D
SA
SA
R W BW0 BW1 C C K K
RW BW0 BW1 C C K K
R
Data In
Data Out
Address
R
Vt
Vt
R
W
BW
MEMORY
CONTROLLER
Return CLK
Vt
Vt
Source CLK
Return CLK
Source CLK
R=50Ω Vt=VREF
SRAM1 Input CQ
SRAM1 Input CQ
SRAM4 Input CQ
SRAM4 Input CQ
Rev. 5.0 July 2006
- 13 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
TIMING WAVE FORMS OF READ AND NOP
READ
READ
NOP
NOP
tKHKH
tKLKH
K
tKHKH
tKHKL
K
tAVKH tKHAX
SA
R
A1
A2
tIVKH tKHIX
tCHQX1
Q
Q1-1
Q1-2
tCHQX
Q1-3
Q1-4
Q2-1
Q2-2
Q2-3
Q2-4
(Data Out)
tKHKH
tKHCH
tCHQV
tKLKH
C
tKHKL
tKHKH
tCHQZ
C
tCHCQV
tCHCQX
tCHQV
tCQHQV
CQ
CQ
tCQHQX
tCHCQV
tCHCQX
Don′t Care
Undefined
Note: 1. Q1-1 refers to output from address A1+0, Q1-2 refers to output from address A1+1 i.e. the next internal burst address following A1+0.
2. Outputs are disabled one cycle after a NOP.
TIMING WAVE FORMS OF WRITE AND NOP
WRITE
WRITE
NOP
NOP
tKHKH
tKLKH
K
tKHKH
tKHKL
K
tAVKH tKHAX
SA
A1
A2
tIVKH tKHIX
tKHIX
W
D(Data In)
D1-1
D1-2
D1-3
D1-4
D2-1
D2-2
D2-3
D2-4
tDVKH
tKHDX
Don′t Care
Undefined
Note: 1. D1-1 refers to input to address A1+0, D1-2 refers to input to address A1+1, i.e the next internal burst address following A1+0.
2. BWx (NWx) assumed active.
Rev. 5.0 July 2006
- 14 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
TIMING WAVE FORMS OF READ, WRITE AND NOP
READ
WRITE
READ
WRITE
NOP
NOP
K
K
SA
W
A1
A2
A3
A4
R
D(Data In)
D2-1
Q1-1
D2-2
Q1-2
D2-3
Q1-3
D2-4
Q1-4
D4-1
D4-2
Q3-2
D4-3
D(Data Out)
Q3-1
Q3-3
C
C
Don′t Care
Undefined
Note: 1. If address A3=A2, data Q3-1=D2-1, data Q3-2=D2-2 , data Q3-3=D2-3, data Q3-4=D2-4
Write data is forwarded immediately as read results.
2.BWx (NWx) assumed active.
Rev. 5.0 July 2006
- 15 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
IEEE 1149.1 TEST ACCESS PORT AND BOUNDARY SCAN-JTAG
This part contains an IEEE standard 1149.1 Compatible Test Access Port (TAP). The package pads are monitored by the Serial Scan
circuitry when in test mode. This is to support connectivity testing during manufacturing and system diagnostics. Internal data is not
driven out of the SRAM under JTAG control. In conformance with IEEE 1149.1, the SRAM contains a TAP controller, Instruction Reg-
ister, Bypass Register and ID register. The TAP controller has a standard 16-state machine that resets internally upon power-up,
therefore, TRST signal is not required. It is possible to use this device without utilizing the TAP. To disable the TAP controller without
interfacing with normal operation of the SRAM, TCK must be tied to VSS to preclude mid level input. TMS and TDI are designed so an
undriven input will produce a response identical to the application of a logic 1, and may be left unconnected. But they may also be
tied to VDD through a resistor. TDO should be left unconnected.
JTAG BLOCK DIAGRAM
JTAG INSTRUCTION CODING
IR2 IR1 IR0 Instruction
TDO Output
Notes
0
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
EXTEST
IDCODE
SAMPLE-Z
Boundary Scan Register
Identification Register
Boundary Scan Register
1
3
2
6
5
6
6
4
0
0
0
RESERVED Do Not Use
A,D
K,K
1
SAMPLE
Boundary Scan Register
C,C
1
RESERVED Do Not Use
RESERVED Do Not Use
SRAM
CORE
1
1
Q
CQ
BYPASS
Bypass Register
CQ
NOTE :
1. Places DQs in Hi-Z in order to sample all input data regardless of other
SRAM inputs. This instruction is not IEEE 1149.1 compliant.
TDI
BYPASS Reg.
Identification Reg.
Instruction Reg.
2. Places DQs in Hi-Z in order to sample all input data regardless of other
SRAM inputs.
TDO
3. TDI is sampled as an input to the first ID register to allow for the serial shift
of the external TDI data.
4. Bypass register is initiated to VSS when BYPASS instruction is invoked. The
Bypass Register also holds serially loaded TDI when exiting the Shift DR
states.
5. SAMPLE instruction dose not places DQs in Hi-Z.
6. This instruction is reserved for future use.
Control Signals
TAP Controller
TMS
TCK
TAP CONTROLLER STATE DIAGRAM
1
0
Test Logic Reset
0
1
1
0
1
Run Test Idle
Select DR
0
Capture DR
0
Shift DR
1
Exit1 DR
0
Select IR
0
1
1
1
1
Capture IR
0
0
Shift IR
1
Exit1 IR
0
0
0
0
0
Pause DR
1
Pause IR
1
Exit2 IR
1
Exit2 DR
1
1
0
Update DR
0
Update IR
1
Rev. 5.0 July 2006
- 16 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
SCAN REGISTER DEFINITION
Part
Instruction Register
Bypass Register
ID Register
32 bits
32 bits
Boundary Scan
107 bits
512Kx36
1Mx18
3 bits
3 bits
1 bit
1 bit
107 bits
ID REGISTER DEFINITION
Revision Number
Part Configuration
(28:12)
00def0wx0t0q0b0s0
Samsung JEDEC Code
(11: 1)
Part
Start Bit(0)
(31:29)
000
512Kx36
1Mx18
00001001110
00001001110
1
1
000
00def0wx0t0q0b0s0
Note : Part Configuration
/def=001 for 18Mb, /wx=11 for x36, 10 for x18
/t=1 for DLL Ver., 0 for non-DLL Ver. /q=1 for QDR, 0 for DDR /b=1 for 4Bit Burst, 0 for 2Bit Burst /s=1 for Separate I/O, 0 for Common I/O
BOUNDARY SCAN EXIT ORDER
ORDER
PIN ID
ORDER
PIN ID
10D
9E
10C
11D
9C
ORDER
73
PIN ID
2C
3E
2D
2E
1E
2F
3F
1G
1F
3G
2G
1J
2J
3K
3J
2K
1K
2L
1
2
6R
6P
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
3
4
6N
7P
5
6
7N
7R
9D
7
8
8R
8P
11B
11C
9B
10B
11A
Internal
9A
8B
7C
6C
8A
7A
7B
6B
6A
5B
5A
4A
5C
4B
3A
1H
1A
2B
3B
1C
1B
9
9R
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
11P
10P
10N
9P
10M
11N
9M
9N
11L
11M
9L
10L
11K
10K
9J
3L
1M
1L
3N
3M
1N
2M
3P
2N
2P
1P
3R
4R
4P
5P
5N
5R
9K
98
99
10J
11J
11H
10G
9G
11F
11G
9F
100
101
102
103
104
105
106
107
10F
11E
10E
3D
3C
1D
Note: 1. NC pins are read as “X” (i.e. don′t care.)
Rev. 5.0 July 2006
- 17 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
JTAG DC OPERATING CONDITIONS
Parameter
Symbol
Min
1.7
Typ
Max
1.9
Unit
V
Note
Power Supply Voltage
VDD
VIH
1.8
Input High Level
1.3
-
-
-
-
VDD+0.3
0.5
V
Input Low Level
VIL
-0.3
1.4
V
Output High Voltage (IOH=-2mA)
Output Low Voltage(IOL=2mA)
VOH
VOL
VDD
V
VSS
0.4
V
Note: 1. The input level of SRAM pin is to follow the SRAM DC specification.
JTAG AC TEST CONDITIONS
Parameter
Symbol
VIH/VIL
TR/TF
Min
1.8/0.0
1.0/1.0
0.9
Unit
V
Note
Input High/Low Level
Input Rise/Fall Time
ns
V
Input and Output Timing Reference Level
Note: 1. See SRAM AC test output load on page 11.
1
JTAG AC CHARCTERISTICS
Parameter
Symbol
Min
50
20
20
5
Max
Unit
Note
TCK Cycle Time
tCHCH
tCHCL
tCLCH
tMVCH
tCHMX
tDVCH
tCHDX
tSVCH
tCHSX
tCLQV
-
-
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TCK High Pulse Width
TCK Low Pulse Width
TMS Input Setup Time
TMS Input Hold Time
TDI Input Setup Time
TDI Input Hold Time
-
-
5
-
5
-
5
-
SRAM Input Setup Time
SRAM Input Hold Time
Clock Low to Output Valid
5
-
5
-
0
10
JTAG TIMING DIAGRAM
TCK
tCHCH
tCLCH
tCHCL
tMVCH
tCHMX
TMS
TDI
tDVCH
tSVCH
tCHDX
tCHSX
PI
(SRAM)
tCLQV
TDO
Rev. 5.0 July 2006
- 18 -
K7R163684B
K7R161884B
512Kx36 & 1Mx18 QDRTM II b4 SRAM
165 FBGA PACKAGE DIMENSIONS
13mm x 15mm Body, 1.0mm Bump Pitch, 11x15 Ball Array
B
Top View
A
C
Side View
D
A
G
E
B
F
Bottom View
H ∅
E
Symbol
Value
13 ± 0.1
Units
Note
Symbol
Value
1.0
Units
mm
mm
mm
mm
Note
A
B
C
D
mm
mm
mm
mm
E
F
15 ± 0.1
1.3 ± 0.1
0.35 ± 0.05
14.0
G
H
10.0
0.5 ± 0.05
Rev. 5.0 July 2006
- 19 -
相关型号:
K7R161884B-EI160
QDR SRAM, 1MX18, 0.5ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FBGA-165
SAMSUNG
K7R161884B-EI200
QDR SRAM, 1MX18, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FBGA-165
SAMSUNG
K7R161884B-EI250
QDR SRAM, 1MX18, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FBGA-165
SAMSUNG
K7R161884B-EI300
QDR SRAM, 1MX18, 0.45ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, ROHS COMPLIANT, FBGA-165
SAMSUNG
©2020 ICPDF网 联系我们和版权申明