K7R320884M-FC13_技术文档

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

Document Title

1Mx36-bit, 2Mx18-bit, 4Mx8-bit QDR^TMII b4 SRAM

Revision History

Draft Date

Remark

Advance

Rev. No.

History

June 30, 2001

Oct. 20, 2001

0.0

1. Initial document.

0.1

1. Package dimension modify.

P.20 from 13mmx15mm to 15mmx17mm

Preliminary

Dec. 5, 2001

0.2

1. Pin name change from DLL to Doff.

2. Vddq range change from 1.5V to 1.5V~1.8V.

3. Update JTAG test conditions.

4. Reserved pin for high density name change from NC to Vss/SA

5. Delete AC test condition about Clock Input timing Reference Level

6. Delete clock description on page 2 and add HSTL I/O comment

Preliminary

July, 29. 2002

Sep. 6. 2002

0.3

0.4

1. Update current characteristics in DC electrical characteristics

2. Change AC timing characteristics

3. Update JTAG instruction coding and diagrams

1. Add -FC25 part(AC Characteristics)

2. Add AC electrical characteristics.

3. Change AC timing characteristics

4. Change DC electrical characteristics(ISB1)

Preliminary

Oct. 7. 2002

0.5

1. Change the data Setup/Hold time.

2. Change the Access Time.(tCHQV, tCHQX, etc.)

3. Change the Clock Cycle Time.(MAX value of tKHKH)

4. Change the JTAG instruction coding.

Preliminary

Dec. 16, 2002

Dec. 26, 2002

0.6

0.7

1. Change the Boundary scan exit order.

2. Change the AC timing characteristics(-25, -20)

3. Correct the Overshoot and Undershoot timing diagrams.

1. Change the JTAG Block diagram

The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the

specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions on the parameters of this device. If you have any ques-

tions, please contact the SAMSUNG branch office near your office, call or contact Headquarters.

Dec. 2002

Rev 0.7

- 1 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

1Mx36-bit, 2Mx18-bit, 4Mx8-bit QDR^TMII b4 SRAM

FEATURES

• 1.8V+0.1V/-0.1V Power Supply.

• DLL circuitry for wide output data valid window and future

freguency scaling.

Part

Cycle Access

Organization

Unit

Number

Time

• I/O Supply Voltage 1.5V+0.1V/-0.1V for 1.5V I/O,

1.8V+0.1V/-0.1V for 1.8V I/O.

• Separate independent read and write data ports

with concurrent read and write operation

• HSTL I/O

• Full data coherency, providing most current data .

• Synchronous pipeline read with self timed late write.

• Registered address, control and data input/output.

• DDR(Double Data Rate) Interface on read and write ports.

• Fixed 4-bit burst for both read and write operation.

• Clock-stop supports to reduce current.

• Two input clocks(K and K) for accurate DDR timing at clock

rising edges only.

• Two input clocks for output data(C and C) to minimize

clock-skew and flight-time mismatches.

• Two echo clocks (CQ and CQ) to enhance output data

traceability.

K7R323684M-FC25

K7R323684M-FC20

K7R323684M-FC16

K7R323684M-FC13

K7R321884M-FC25

K7R321884M-FC20

K7R321884M-FC16

K7R321884M-FC13

K7R320884M-FC25

K7R320884M-FC20

K7R320884M-FC16

K7R320884M-FC13

4.0

5.0

6.0

7.5

4.0

5.0

6.0

7.5

4.0

5.0

6.0

7.5

0.45

0.50

0.45

0.50

0.45

0.50

ns

X36

X18

X8

• Single address bus.

• Byte write (x18, x36) and nybble(x8) write function.

• Sepatate read/write control pin(R and W)

• Simple depth expansion with no data contention.

• Programmable output impenance.

• JTAG 1149.1 compatible test access port.

• 165FBGA(11x15 ball aray FBGA) with body size of 15x17mm

FUNCTIONAL BLOCK DIAGRAM

36 (or 18)

18 (or 19)

DATA

REG

D(Data in)

72(or 36)

WRITE DRIVER

18

(or 19)

ADD

REG

ADDRESS

R

72

144

(or 72)

1Mx36

(2Mx18)

MEMORY

ARRAY

(or 36)

36 (or 18)

CTRL

Q(Data Out)

W

BWX

LOGIC

72

4 (or 2)

CQ, CQ

(or 36)

(Echo Clock out)

K

CLK

GEN

C

SELECT OUTPUT CONTROL

Notes: 1. Numbers in ( ) are for x18 device, x8 device also the same with appropriate adjustments of depth and width.

QDR SRAM and Quad Data Rate comprise a new family of products developed by Cypress, Hitachi, IDT, Micron, NEC and Samsung techno logy.

Dec. 2002

Rev 0.7

- 2 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

PIN CONFIGURATIONS(TOP VIEW) K7R323684M(1Mx36)

1

2

3

4

5

6

7

8

9

10

VSS/SA*

Q17

Q7

11

CQ

Q8

D8

A

B

C

D

E

F

CQ

VSS/SA* NC/SA*

W

BW2

BW3

SA

K

BW1

BW0

SA

R

SA

Q27

D27

D28

Q29

Q30

D30

Doff

D31

Q32

Q33

D33

D34

Q35

TDO

Q18

Q28

D20

D29

Q21

D22

VREF

Q31

D32

Q24

Q34

D26

D35

TCK

D18

D19

Q19

Q20

D21

Q22

VDDQ

D23

Q23

D24

D25

Q25

Q26

SA

K

SA

D17

D16

Q16

Q15

D14

Q13

VDDQ

D12

Q12

D11

D10

Q10

Q9

VSS

VDDQ

VSS

SA

NC

VSS

SA

C

VSS

VDD

VSS

SA

VSS

VDD

VSS

SA

VSS

D15

D6

D7

VDDQ

VSS

Q6

Q5

D5

Q14

D13

VREF

Q4

G

H

J

ZQ

D4

K

L

D3

Q3

Q2

D2

Q11

Q1

M

N

P

R

VSS

D9

D1

SA

D0

Q0

TDI

SA

C

SA

TMS

Notes : 1. * Checked No Connect(NC) pins are reserved for higher density address, i.e. 3A for 64Mb, 10A for 128Mb and 2A for 256Mb.

2. BW0 controls write to D0:D8, BW1 controls write to D9:D17, BW2 controls write to D18:D26 and BW3 controls write to D27:D35.

PIN NAME

SYMBOL

K, K

PIN NUMBERS

DESCRIPTION

Input Clock

NOTE

6B, 6A

C, C

6P, 6R

Input Clock for Output Data

Output Echo Clock

DLL Disable when low

Address Inputs

1

CQ, CQ

Doff

11A, 1A

1H

SA

9A,4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R

10P,11N,11M,10K,11J,11G,10E,11D,11C,10N,9M,9L

9J,10G,9F,10D,9C,9B,3B,3C,2D,3F,2G,3J,3L,3M,2N

1C,1D,2E,1G,1J,2K,1M,1N,2P

D0-35

Q0-35

Data Inputs

11P,10M,11L,11K,10J,11F,11E,10C,11B,9P,9N,10L

9K,9G,10F,9E,9D,10B,2B,3D,3E,2F,3G,3K,2L,3N

3P,1B,2C,1E,1F,2J,1K,1L,2M,1P

Data Outputs

W

4A

Write Control Pin,active when low

Read Control Pin,active when low

Block Write Control Pin,active when low

Input Reference Voltage

R

8A

BW0, BW1,BW2, BW3

7B,7A,5A,5B

VREF

ZQ

2H,10H

11H

Output Driver Impedance Control Input

Power Supply ( 1.8 V )

2

VDD

5F,7F,5G,7G,5H,7H,5J,7J,5K,7K

4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L

VDDQ

Output Power Supply ( 1.5V or 1.8V )

2A,10A,4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M,

8M,4N,8N

VSS

Ground

TMS

TDI

10R

11R

2R

JTAG Test Mode Select

JTAG Test Data Input

JTAG Test Clock

TCK

TDO

NC

1R

JTAG Test Data Output

No Connect

3A,6C

3

Notes: 1. C, C, K or K cannot be set to VREF voltage.

2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected.

3. Not connected to chip pad internally.

Dec. 2002

Rev 0.7

- 3 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

PIN CONFIGURATIONS(TOP VIEW) K7R321884M(2Mx18)

1

CQ

NC

Doff

NC

TDO

2

VSS/SA*

Q9

3

4

5

6

7

8

9

SA

NC

VDDQ

NC

SA

10

VSS/SA*

NC

11

CQ

Q8

D8

A

B

C

D

E

F

SA

W

BW1

NC

SA

K

NC

BW0

SA

R

D9

SA

K

SA

NC

D10

Q10

Q11

D12

Q13

VDDQ

D14

Q14

D15

D16

Q16

Q17

SA

VSS

VDDQ

VSS

SA

NC

VSS

SA

C

VSS

Q7

D11

NC

VSS

VDD

VSS

SA

VSS

VDD

VSS

SA

VSS

NC

D7

VDDQ

VSS

D6

Q6

Q5

D5

Q12

D13

VREF

NC

G

H

J

NC

VREF

Q4

ZQ

D4

K

L

NC

D3

Q3

Q2

D2

Q15

NC

M

N

P

R

Q1

D17

NC

VSS

NC

D1

SA

D0

Q0

TDI

TCK

SA

C

SA

TMS

Notes: 1. * Checked No Connect(NC) pins are reserved for higher density address, i.e. 10A for 64Mb and 2A for 128Mb.

2. BW0 controls write to D0:D8 and BW1 controls write to D9:D17.

PIN NAME

SYMBOL

K, K

PIN NUMBERS

DESCRIPTION

NOTE

6B, 6A

Input Clock

C, C

6P, 6R

Input Clock for Output Data

Output Echo Clock

1

CQ, CQ

Doff

11A, 1A

1H

DLL Disable when low

Address Inputs

SA

3A,9A,4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R

10P,11N,11M,10K,11J,11G,10E,11D,11C,3B,3C,2D

3F,2G,3J,3L,3M,2N

D0-17

Q0-17

Data Inputs

11P,10M,11L,11K,10J,11F,11E,10C,11B,2B,3D,3E

2F,3G,3K,2L,3N,3P

Data Outputs

W

R

4A

Write Control Pin,active when low

Read Control Pin,active when low

Block Write Control Pin,active when low

Input Reference Voltage

8A

BW0, BW1

VREF

ZQ

7B, 5A

2H,10H

11H

Output Driver Impedance Control Input

Power Supply ( 1.8 V )

2

VDD

5F,7F,5G,7G,5H,7H,5J,7J,5K,7K

VDDQ

4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L

Output Power Supply ( 1.5V or 1.8V )

VSS

TMS

TDI

2A,10A,4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M-8M,4N,8N

Ground

10R

11R

2R

JTAG Test Mode Select

JTAG Test Data Input

JTAG Test Clock

TCK

TDO

1R

JTAG Test Data Output

7A,1B,5B,9B,10B,1C,2C,6C,9C,1D,9D,10D,1E,2E,9E,1F

9F,10F,1G,9G,10G,1J,2J,9J,1K,2K,9J,1L,9L,10L,1M

2M,9M,1N,9N,10N,1P,2P,9P

NC

No Connect

3

Notes: 1. C, C, K or K cannot be set to VREF voltage.

2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected.

3. Not connected to chip pad internally.

Dec. 2002

Rev 0.7

- 4 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

PIN CONFIGURATIONS(TOP VIEW) K7R320884M(4Mx8)

1

CQ

NC

Doff

NC

TDO

2

VSS/SA*

NC

3

SA

4

5

6

7

8

9

SA

NC

VDDQ

NC

SA

10

SA

11

CQ

Q3

D3

A

B

C

D

E

F

W

NW1

NC

SA

K

NC

NW 0

SA

R

NC

Q4

SA

K

SA

NC

D2

NC

VSS

VDDQ

VSS

SA

NC

VSS

SA

C

VSS

D4

VSS

VDD

VSS

SA

VSS

VDD

VSS

SA

VSS

NC

Q2

NC

ZQ

D1

NC

VDDQ

VSS

NC

Q5

NC

VREF

Q1

NC

TMS

G

H

J

D5

VREF

NC

VDDQ

NC

D6

K

L

NC

Q0

D0

Q6

M

N

P

R

NC

Q7

D7

VSS

NC

TDI

NC

SA

TCK

SA

C

SA

Notes: 1. * Checked No Connect(NC) pin is reserved for higher density address, i.e. 2A for 72Mb.

2. NW 0 controls write to D0:D3 and NW1 controls write to D4:D7.

PIN NAME

SYMBOL

K, K

PIN NUMBERS

DESCRIPTION

NOTE

6B, 6A

Input Clock

C, C

6P, 6R

Input Clock for Output Data

Output Echo Clock

DLL Disable when low

Address Inputs

1

CQ, CQ

Doff

11A, 1A

1H

SA

3A,9A,10A,4B,8B,5C,7C,5N-7N,4P,5P,7P,8P,3R-5R,7R-9R

11M,11J,10E,11C,2D,2G,3L,2N

11L,10J,11E,11B,3E,3G,2L,3P

D0-7

Q0-7

Data Inputs

Data Outputs

W

R

4A

Write Control Pin,active when low

Read Control Pin,active when low

Nybble Write Control Pin,active when low

Input Reference Voltage

8A

NW0, NW1

VREF

ZQ

7B, 5A

2H,10H

11H

Output Driver Impedance Control Input

Power Supply ( 1.8 V )

2

VDD

5F,7F,5G,7G,5H,7H,5J,7J,5K,7K

VDDQ

VSS

4E,8E,4F,8F,4G,8G,3H,4H,8H,9H,4J,8J,4K,8K,4L,8L

Output Power Supply ( 1.5V or 1.8V )

Ground

2A,4C,8C,4D-8D,5E-7E,6F,6G,6H,6J,6K,5L-7L,4M-8M,4N,8N

TMS

TDI

10R

11R

2R

JTAG Test Mode Select

JTAG Test Data Input

TCK

TDO

JTAG Test Clock

1R

JTAG Test Data Output

7A,1B,2B,3B,5B,9B,10B,1C,2C,3C,6C,9C,10C,1D,3D,9D,10D,

11D,1E,2E,9E,1F,2F,3F,9F,10F,11F,1G,9G,10G,11G,1J,2J,3J

9J,1K,2K,3K,10K,11K,9J,1L,9L,10L,1M,2M,3M,9M,10M,1N,3N

9N,10N,11N,1P,2P,9P,10P,11P

NC

No Connect

3

Notes: 1. C, C, K or K cannot be set to VREF voltage.

2. When ZQ pin is directly connected to VDD output impedance is set to minimum value and it cannot be connected to ground or left unconnected.

3. Not connected to chip pad internally.

Dec. 2002

Rev 0.7

- 5 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

GENERAL DESCRIPTION

The K7R323684M, K7R321884M and K7R320884M are37,748,736-bits QDR(Quad Data Rate)

Synchronous Pipelined Burst SRAMs.

They are organized as 1,048,576 words by 36bits for K7R323684M, 2,097,152 words by 18 bits for K7R321884M and

4,194,304 words by 8bits for K7R320884M.

The QDR operation is possible by supporting DDR read and write operations through separate data output and input ports

with the same cycle. Memory bandwidth is maxmized as data can be transfered into sram

on every rising edge of K and K, and transfered out of sram on every rising edge of C and C.

And totally independent read and write ports eliminate the need for high speed bus turn around.

Address for read and write are latched on alternate rising edges of the input clock K.

Data inputs, and all control signals are synchronized to the input clock ( K or K ).

Normally data outputs are synchronized to output clocks ( C and C ), but when C and C are tied high,

the data outputs are synchronized to the input clocks ( K and K ).

Read data are referenced to echo clock ( CQ or CQ ) outputs.

Common address bus is used to access address both for read and write operations.

The internal burst counter is fiexd to 4-bit sequential for both read and write operations, reguiring tow full clock bus cycles.

Any request that attempts to interrupt a burst operation in progress is ignored.

Synchronous pipeline read and late write enable high speed operations.

Simple depth expansion is accomplished by using R and W for port selection.

Byte write operation is supported with BW0 and BW1 ( BW2 and BW3 ) pins.

Nybble write operation is supported with NW 0 and NW1 pins for x8 device.

IEEE 1149.1 serial boundary scan (JTAG) simplifies monitoring package pads attachment status with system.

The K7R323684M, K7R321884M and K7R320884M are implemented with SAMSUNG's high performance 6T CMOS technology

and is available in 165pin FBGA packages. Multiple power and ground pins minimize ground bounce.

Read Operations

Read cycles are initiated by activating R at the rising edge of the positive input clock K.

Address is presented and stored in the read address register synchronized with K clock.

For 4-bit burst DDR operation, it will access four 36-bit or 18-bit or 8-bit data words with each read command.

The first pipelined data is transfered out of the device triggered by C clock following next K clock rising edge.

Next burst data is triggered by the rising edge of following C clock rising edge.

The process continues until all four data are transfered.

Continuous read operations are initated with K clock rising edge.

And pipelined data are transferred out of device on every rising edge of both C and C clocks.

In case C and C tied to high, output data are triggered by K and K insted of C and C.

When the R is disabled after a read operation,the K7R323684M, K7R321884M and K7R320884M will first complete

burst read operation

before entering into deselect mode at the next K clock rising edge.

Then output drivers disabled automatically to high impedance state.

Echo clock operation

To assure the output tracibility, the SRAM provides the output Echo clock, pair of compliment clock CQ and CQ,

which are synchronized with internal data output.

Echo clocks run free during normal operation.

The Echo clock is triggered by internal output clock signal, and transfered to external through same structures

as output driver.

Dec. 2002

Rev 0.7

- 6 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

Write Operations

Write cycles are initiated by activating W at the rising edge of the positive input clock K.

Address is presented and stored in the write address register synchronized with K clock.

For 4-bit burst DDR operation, it will write four 36-bit or 18-bit or 8-bit data words with each write command.

The first "late" data is transfered and registered in to the device synchronous with next K clock rising edge.

Next burst data is transfered and registered synchronous with following K clock rising edge.

The process continues until all four data are transfered and registered.

Continuous write operations are initated with K rising edge.

And "late writed" data is presented to the device on every rising edge of both K and K clocks.

The device disregards input data presented on the same cycle W disabled.

When the W is disabled after a read operation, the K7R323684M, K7R321884M and K7R320884M will first complete

burst read operation before entering into deselect mode at the next K clock rising edge.

The K7R323684M and K7R321884M support byte write operations.

With activating BW0 or BW1 ( BW2 or BW3 ) in write cycle, only one byte of input data is presented.

In K7R321884M, BW0 controls write operation to D0:D8, BW1 controls write operation to D9:D17.

And in K7R323684M BW2 controls write operation to D18:D26, BW3 controls write operation to D27:D35.

The the K7R320884M support nybble write operations.

In K7R320884M, NW0 controls write operation to D0:D3, NW1 controls write operation to D4:D7.

Programmable Impedance Output Buffer Operation

The designer can program the SRAM's output buffer impedance by terminating the ZQ pin to VSS through a precision resistor(RQ).

The value of RQ (within 15%) is five times the output impedance desired.

For example, 250W resistor will give an output impedance of 50W.

Impedance updates occur early in cycles that do not activate the outputs, such as deselect cycles.

In all cases impedance updates are transparent to the user and do not produce access time "push-outs"

or other anomalous behavior in the SRAM.

There are no power up requirements for the SRAM. However, to guarantee optimum output driver impedance after power up,

the SRAM needs 1024 non-read cycles.

Single Clock Mode

The K7R323684M, K7R321884M and K7R320884M can be operated with the single clock pair K and K,

insted of C or C for output clocks.

To operate these devices in single clock mode, C and C must be tied high during power up and must be maintained high

during operation.

After power up, this device can’ t change to or from single clock mode.

System flight time and clock skew could not be compensated in this mode.

Depth Expansion

Separate input and output ports enables easy depth expansion.

Each port can be selected and deselected independently

and read and write operation do not affect each other.

Before chip deselected, all read and write pending operations are completed.

Dec. 2002

Rev 0.7

- 7 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

STATE DIAGRAM

POWER-UP

READ NOP

READ

WRITE

WRITE NOP

WRITE

READ

D count=2

WRITE

D count=2

LOAD NEW

READ ADDRESS

D count=0

LOAD NEW

WRITE ADDRESS

D count=0

WRITE

D count=2

READ

D count=2

ALWAYS

DDR READ

D count=D count+1

DDR WRITE

D count=D count+1

READ

D count=1

WRITE

D count=1

ALWAYS

INCREMENT

READ ADDRESS

WRITE ADDRESS

Notes: 1. Internal burst counter is fixed as 2-bit linear, i.e. when first address is A0+0, next internal burst address is A0+1.

2. "READ" refers to read active status with R=Low, "READ" refers to read inactive status with R=high. "WRITE" and "WRITE" are the same case.

3. Read and write state machine can be active simulateneously.

4. State machine control timing sequence is controlled by K.

Dec. 2002

Rev 0.7

- 8 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

TRUTH TABLES

SYNCHRONOUS TRUTH TABLE

D

Q

K

R

W

OPERATION

D(A1)

D(A2)

D(A3)

D(A4)

Q(A1)

Q(A2)

Q(A3)

Q(A4)

Previous Previous Previous Previous Previous Previous Previous Previous

Stopped

X

H

X

H

X

Clock Stop

No Operation

Read

state

X

state

X

state

X

state

X

state

High-Z

DOUT

state

High-Z

DOUT

state

High-Z

DOUT

state

High-Z

DOUT

•

4

X

L

at C(t+1) at C(t+2) at C(t+2) at C(t+3)

Din

5

4

•

X

Write

H

L

at K(t+1) at K(t+1) at K(t+2) at K(t+2)

Notes: 1. X means "Don¢t Care".

2. The rising edge of clock is symbolized by ( • ).

3. Before enter into clock stop status, all pending read and write operations will be completed.

4. This signal was HIGH on previous K clock rising edge. Initating consecutive READ or WRITE operations on consecutive K clock rising edges

is not permitted. The device will ignore the second request.

5. If this signal was LOW to inititate the previous cycle, this signal becomes a don¢t care for this operation however it is strongly recommended

that this signal is brought HIGH as shown in the truth table.

WRITE TRUTH TABLE(x18)

K

BW0

L

BW1

L

OPERATION

•

WRITE ALL BYTEs ( K• )

WRITE BYTE 0 ( K• )

WRITE BYTE 1 ( K• )

WRITE NOTHING ( K• )

•

L

•

L

H

•

L

H

L

•

H

L

H

•

H

Notes: 1. X means "Don¢t Care".

2. All inputs in this table must meet setup and hold time around the rising edge of input clock K or K ( • ).

3. Assumes a WRITE cycle was initiated.

4. This table illustates operation for x18 devices. x8 device operation is similar except that NW0 controls D0:D3 and NW 0 controls D4:D7.

WRITE TRUTH TABLE(x36)

K

BW0

L

BW 1

L

BW2

L

BW 3

L

OPERATION

WRITE ALL BYTEs ( K• )

WRITE BYTE 0 ( K• )

•

L

•

L

H

L

H

•

L

H

WRITE BYTE 0 ( K• )

H

L

H

WRITE BYTE 1 ( K• )

•

L

H

WRITE BYTE 1 ( K• )

H

L

WRITE BYTE 2 and BYTE 3 ( K• )

WRITE NOTHING ( K• )

•

H

L

H

•

H

Notes: 1. X means "Don¢t Care".

2. All inputs in this table must meet setup and hold time around the rising edge of input clock K or K ( • ).

3. Assumes a WRITE cycle was initiated.

Dec. 2002

Rev 0.7

- 9 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

ABSOLUTE MAXIMUM RATINGS*

PARAMETER

Voltage on VDD Supply Relative to VSS

Voltage on VDDQ Supply Relative to VSS

Voltage on Input Pin Relative to VSS

Power Dissipation

SYMBOL

VDD

RATING

-0.5 to 2.9

-0.5 to VDD

-0.5 to VDD+0.3

TBD

UNIT

V

VDDQ

VIN

V

PD

W

Storage Temperature

TSTG

TOPR

TBIAS

-65 to 150

0 to 70

°C

Operating Temperature

Storage Temperature Range Under Bias

-10 to 85

*Note: 1. Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating

only and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

2. VDDQ must not exceed VDD during normal operation.

DC ELECTRICAL CHARACTERISTICS(VDD=1.8V ±0.1V, TA=0°C to +70°C)

PARAMETER

Input Leakage Current

Output Leakage Current

SYMBOL

TEST CONDITIONS

VDD=Max ; VIN=VSS to VDDQ

Output Disabled,

MIN

MAX

+2

UNIT NOTES

IIL

-2

-

mA

IOL

+2

-25

-20

-16

-13

-25

-20

-16

-13

-25

-20

-16

-13

-25

-20

-16

-13

800

700

600

550

750

650

550

500

730

630

530

480

230

200

190

-

VDD=Max , IOUT=0mA

Operating Current (x36): DDR

Operating Current (x18): DDR

Operating Current (x8): DDR

Standby Current(NOP): DDR

ICC

ISB1

mA

1,5

1,6

Cycle Time ³ tKHKH Min

-

VDD=Max , IOUT=0mA

Cycle Time ³ tKHKH Min

VDD=Max , IOUT=0mA

Cycle Time ³ tKHKH Min

-

Device deselected,

IOUT=0mA, f=Max,

All Inputs £0.2V or³ V DD-0.2V

Output High Voltage

Output Low Voltage

Output High Voltage

Output Low Voltage

Input Low Voltage

Input High Voltage

VOH1

VOL1

VOH2

VOL2

VIL

VDDQ/2-0.12 VDDQ/2+0.12

V

2,7

3,7

4

IOH=-1.0mA

IOL=1.0mA

VDDQ-0.2

VSS

VDDQ

0.2

4

-0.3

VREF-0.1

VDDQ+0.3

8,9

8,10

VIH

VREF+0.1

Notes: 1. Minimum cycle. IOUT=0mA.

2. |IOH|=(VDDQ/2)/(RQ/5) for 175W £ RQ £ 350W.

3. |IOL|=(VDDQ/2)/(RQ/5) for 175W £ RQ £ 350W.

4. Minimum Impedance Mode when ZQ pin is connected to VDD.

5. Operating current is calculated with 50% read cycles and 50% write cycles.

6. Standby Current is only after all pending read and write burst opeactions are completed.

7. Programmable Impedance Mode.

8. These are DC test criteria. DC design criteria is VREF±50mV. The AC VIH /VIL levels are defined separately for measuring

timing parameters.

9. VIL (Min)DC=-0.3V, VIL (Min)AC=-1.5V(pulse width £ 3ns).

10. VIH (Max)DC=VDDQ+0.3, VIH (Max)AC=VDDQ +0.85V(pulse width £ 3ns).

Dec. 2002

Rev 0.7

- 10 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

AC ELECTRICAL CHARACTERISTICS (VDD=1.8V ±0.1V, TA=0°C to +70°C)

PARAMETER

Input High Voltage

Input Low Voltage

MAX

UNIT

NOTES

1,2

SYMBOL

VIH (AC)

VIL (AC)

MIN

VREF + 0.2

-

V

VREF - 0.2

1,2

Notes: 1. This condition is for AC function test only, not for AC parameter test.

2. To maintain a valid level, the transitioning edge of the input must :

a) Sustain a constant slew rate from the current AC level through the target AC level, VIL(AC) or VIH(AC)

b) Reach at least the target AC level

c) After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC)

Overershoot Timing

Undershoot Timing

20% tKHKH(MIN)

VIH

VDDQ+0.5V

VDDQ +0.25V

VDDQ

VSS

VSS-0.25V

VSS-0.5V

20% tKHKH(MIN)

VIL

Note: For power-up, VIH £ VDDQ+0.3V and VDD £ 1.7V and VDDQ £ 1.4V t £ 200ms

OPERATING CONDITIONS (0°C £ TA £ 70°C)

PARAMETER

SYMBOL

MIN

1.7

1.4

0.68

0

MAX

1.9

0.95

0

UNIT

VDD

V

Supply Voltage

VDDQ

VREF

VSS

Reference Voltage

Ground

AC TEST CONDITIONS

Parameter

Symbol

VDD

Value

1.7~1.9

1.4~1.9

1.25/0.25

0.75

Unit

V

AC TEST OUTPUT LOAD

Core Power Supply Voltage

Output Power Supply Voltage

Input High/Low Level

VDDQ

V

0.75V

VREF

VDDQ/2

VIH/VIL

VREF

V

Input Reference Level

V

50W

SRAM

Zo=50W

Input Rise/Fall Time

TR/TF

0.3/0.3

VDDQ/2

ns

V

Output Timing Reference Level

250W

ZQ

Note: Parameters are tested with RQ=250W

Dec. 2002

Rev 0.7

- 11 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

AC TIMING CHARACTERISTICS(VDD=1.8V±0.1V, TA=0°C to +70°C)

-25

-20

-16

MAX

-13

MAX

PARAMETER

SYMBOL

UNITS NOTES

MIN

MAX

MIN

MAX

MIN

Clock

Clock Cycle Time (K, K, C, C)

Clock Phase Jitter (K, K, C, C)

Clock High Time (K, K, C, C)

Clock Low Time (K, K, C, C)

tKHKH

tKC var

tKHKL

4.00

5.25

0.20

5.00

6.30

0.20

6.00

7.88

0.20

7.50

8.40

0.20

ns

5

6

1.60

1.80

0.00

1024

30

2.00

2.20

0.00

1024

30

2.40

2.70

0.00

1024

30

3.00

3.38

0.00

1024

30

tKLKH

ns

Clock to Clock (K•

®

K• , C• ® C• )

tKHKH

2.20

1.80

2.75

2.30

3.30

2.80

4.13

3.55

ns

Clock to data clock (K• ® C• , K• ® C• )

DLL Lock Time (K, C)

tKHCH

tKC lock

tKC reset

ns

cycle

ns

K Static to DLL reset

Output Times

C, C High to Output Valid

C, C High to Output Hold

C, C High to Echo Clock Valid

C, C High to Echo Clock Hold

CQ, CQ High to Output Valid

CQ, CQ High to Output Hold

C, High to Output High-Z

C, High to Output Low-Z

Setup Times

tCHQV

tCHQX

0.45

0.30

0.45

0.35

0.45

0.50

0.40

0.50

0.40

0.50

ns

3

-0.45

-0.30

-0.45

-0.35

-0.45

-0.50

-0.40

-0.50

-0.40

-0.50

tCHCQV

tCHCQX

tCQHQV

tCQHQX

tCHQZ

7

3

tCHQX1

Address valid to K rising edge

Control inputs valid to K rising edge

Data-in valid to K, K rising edge

Hold Times

tAVKH

tIVKH

0.50

0.35

0.60

0.40

0.70

0.50

0.70

0.50

ns

2

tDVKH

K rising edge to address hold

K rising edge to control inputs hold

K, K rising edge to data-in hold

tKHAX

tKHIX

0.50

0.35

0.60

0.40

0.70

0.50

0.70

0.50

ns

tKHDX

Notes: 1. All address inputs must meet the specified setup and hold times for all latching clock edges.

2. Control singles are R, W,BW0,BW1 and (NW0, NW1, for x8) and (BW2, BW3, also for x36)

3. If C,C are tied high, K,K become the references for C,C timing parameters.

4. To avoid bus contention, at a given voltage and temperature tCHQX1 is bigger than tCHQZ.

The specs as shown do not imply bus contention beacuse tCHQX1 is a MIN parameter that is worst case at totally different test conditions

(0°C, 1.9V) than tCHQZ, which is a MAX parameter(worst case at 70°C, 1.7V)

It is not possible for two SRAMs on the same board to be at such different voltage and temperature.

5. Clock phase jitter is the variance from clock rising edge to the next expected clock rising edge.

6. Vdd slew rate must be less than 0.1V DC per 50 ns for DLL lock retention. DLL lock time begins once Vdd and input clock are stable.

7. Echo clock is very tightly controlled to data valid/data hold. By design, there is a ± 0.1ns variation from echo clock to data.

The data sheet parameters reflect tester guardbands and test setup variations.

Dec. 2002

Rev 0.7

- 12 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

PIN CAPACITANCE

PRMETER

Address Control Input Capacitance

Input and Output Capacitance

Clock Capacitance

SYMBOL

CIN

TESTCONDITION

TYP

MAX

Unit

pF

NOTES

VIN=0V

VOUT=0V

-

4

6

5

7

6

COUT

pF

CCLK

pF

Note: 1. Parameters are tested with RQ=250Wand VDDQ=1.5V.

2. Periodically sampled and not 100% tested.

THERMAL RESISTANCE

PRMETER

Junction to Ambient

SYMBOL

TYP

TBD

Unit

NOTES

qJA

qJC

qJB

°C/W

Junction to Case

Junction to Pins

Note: Junction temperature is a function of on-chip power dissipation, package thermal impedance, mounting site temperature and mounting site

thermal impedance. TJ=TA + PD x qJA

APPLICATION INRORMATION

2Mx18

SRAM#1

SRAM#4

R=250W

ZQ

Vt

Q0-17

D0-17

SA

D0-17

SA

R W BW0 BW1 C C K K

RW BW0 BW1 C C K K

R

Data In 0-71

Data Out 0-71

Address 0-65

R

Vt

R

W

BW0-7

MEMORY

CONTROLLER

Return CLK

Vt

Source CLK

Return CLK

Source CLK

R=50W Vt=VREF

Dec. 2002

Rev 0.7

- 13 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

TIMING WAVE FORMS OF READ AND NOP

READ

NOP

tKHKH

tKLKH

K

tKHKH

tKHKL

K

tAVKH tKHAX

SA

R

A1

A2

tIVKH tKHIX

tCHQX1

Q

Q1-1

Q1-2

Q1-3

Q1-4

Q2-1

Q2-2

Q2-3

Q2-4

(Data Out)

tKHKH

tKHCH

tCHQV

tCHQX

tKLKH

C

tKHKL

tKHKH

tCHQZ

C

tCHCQV

tCHQV

tCQHQV

tCHCQX

CQ

tCQHQX

tCHCQV

tCHCQX

Don¢t Care

Undefined

Note: 1. Q1-1 refers to output from address A1+0, Q1-2 refers to output from address A1+1 i.e. the next internal burst address following A1+0.

2. Outputs are disabled one cycle after a NOP.

TIMING WAVE FORMS OF WRITE AND NOP

WRITE

NOP

tKHKH

tKLKH

K

tKHKH

tKHKL

K

tAVKH tKHAX

SA

A1

A2

tIVKH tKHIX

tKHIX

W

D(Data In)

D1-1

D1-2

D1-3

D1-4

D2-1

D2-2

D2-3

D2-4

tDVKH

tKHDX

Don ¢t Care

Undefined

Note: 1. D1-1 refers to input to address A1+0, D1-2 refers to input to address A1+1, i.e the next internal burst address following A1+0.

2. BWx ( NWx ) assumed active.

Dec. 2002

Rev 0.7

- 14 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

TIMING WAVE FORMS OF READ, WRITE AND NOP

READ

WRITE

READ

WRITE

NOP

K

SA

W

A1

A2

A3

A4

R

D(Data In)

D2-1

Q1-1

D2-2

Q1-2

D2-3

Q1-3

D2-4

Q1-4

D4-1

D4-2

Q3-2

D4-3

D(Data Out)

Q3-1

Q3-3

C

Don¢t Care

Undefined

Note: 1. If address A3=A2, data Q3-1=D2-1, data Q3-2=D2-2 , data Q3-3=D2-3, data Q3-4=D2-4

Write data is forwarded immediately as read results.

2.BWx ( NWx ) assumed active.

Dec. 2002

Rev 0.7

- 15 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

IEEE 1149.1 TEST ACCESS PORT AND BOUNDARY SCAN-JTAG

This part contains an IEEE standard 1149.1 Compatible Test Access Port(TAP). The package pads are monitored by the Serial Scan

circuitry when in test mode. This is to support connectivity testing during manufacturing and system diagnostics. Internal data is not

driven out of the SRAM under JTAG control. In conformance with IEEE 1149.1, the SRAM contains a TAP controller, Instruction Reg-

ister, Bypass Register and ID register. The TAP controller has a standard 16-state machine that resets internally upon power-up,

therefore, TRST signal is not required. It is possible to use this device without utilizing the TAP. To disable the TAP controller without

interfacing with normal operation of the SRAM, TCK must be tied to VSS to preclude mid level input. TMS and TDI are designed so an

undriven input will produce a response identical to the application of a logic 1, and may be left unconnected. But they may also be

tied to VDD through a resistor. TDO should be left unconnected.

JTAG Block Diagram

JTAG Instruction Coding

IR2 IR1 IR0 Instruction

TDO Output

Notes

0

1

0

1

0

1

0

1

0

1

0

1

0

1

EXTEST

Boundary Scan Register

Identification Register

Boundary Scan Register

1

3

2

6

5

6

4

IDCODE

SAMPLE-Z

RESERVED Do Not Use

A,D

K,K

C,C

SAMPLE

Boundary Scan Register

RESERVED Do Not Use

SRAM

CORE

Q

CQ

BYPASS

Bypass Register

CQ

NOTE :

1. Places DQs in Hi-Z in order to sample all input data regardless of other

SRAM inputs. This instruction is not IEEE 1149.1 compliant.

TDI

BYPASS Reg.

TDO

2. Places DQs in Hi-Z in order to sample all input data regardless of other

SRAM inputs.

Identification Reg.

Instruction Reg.

3. TDI is sampled as an input to the first ID register to allow for the serial shift

of the external TDI data.

4. Bypass register is initiated to VSS when BYPASS instruction is invoked. The

Bypass Register also holds serially loaded TDI when exiting the Shift DR

states.

Control Signals

TAP Controller

TMS

TCK

5. SAMPLE instruction dose not places DQs in Hi-Z.

6. This instruction is reserved for future use.

TAP Controller State Diagram

1

0

Test Logic Reset

0

1

0

1

Run Test Idle

Select DR

0

Select IR

0

1

Capture DR

0

Capture IR

0

Shift DR

1

Shift IR

1

Exit1 DR

0

Exit1 IR

0

Pause DR

1

Pause IR

1

Exit2 DR

1

Exit2 IR

1

0

Update DR

0

Update IR

1

Dec. 2002

Rev 0.7

- 16 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

SCAN REGISTER DEFINITION

Part

1Mx36

2Mx18

4Mx8

Instruction Register

Bypass Register

ID Register

32 bits

Boundary Scan

109 bits

3 bits

1 bit

32 bits

109 bits

32 bits

109 bits

ID REGISTER DEFINITION

Revision Number

Part Configuration

(28:12)

Samsung JEDEC Code

(11: 1)

Part

Start Bit(0)

(31:29)

1Mx36

2Mx18

000

00def0wx0t0q0b0s0

00001001110

1

000

4Mx8

000

Note : Part Configuration

/def=010 for 32Mb, /wx=11 for x36, 10 for x18, 01 for x8

/t=1 for DLL Ver., 0 for non-DLL Ver. /q=1 for DDR, 0 for DDR /b=1 for 4Bit Burst, 0 for 2Bit Burst /s=1 for Separate I/O, 0 for Common I/O

BOUNDARY SCAN EXIT ORDER

ORDER

PIN ID

ORDER

PIN ID

ORDER

73

PIN ID

2C

3E

2D

2E

1E

2F

1

6R

6P

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

10D

9E

74

2

75

3

6N

10C

11D

9C

9D

11B

11C

9B

76

4

7P

77

5

7N

78

6

7R

79

3F

7

8R

80

1G

1F

8

8P

81

9

9R

82

3G

2G

1H

1J

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

11P

10P

10N

9P

10B

11A

10A

9A

83

84

85

86

2J

10M

11N

9M

8B

87

3K

3J

7C

6C

8A

88

89

2K

1K

2L

9N

90

11L

11M

9L

7A

91

7B

92

3L

6B

93

1M

1L

10L

11K

10K

9J

6A

94

5B

95

3N

3M

1N

2M

3P

2N

2P

1P

3R

4R

4P

5P

5N

5R

Internal

5A

96

4A

97

9K

5C

4B

98

10J

11J

11H

10G

9G

99

3A

100

101

102

103

104

105

106

107

108

109

2A

1A

2B

11F

11G

9F

3B

1C

1B

10F

11E

10E

3D

3C

1D

Note: 1. NC pins are read as "X" ( i.e. don¢t care.)

Dec. 2002

Rev 0.7

- 17 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

JTAG DC OPERATING CONDITIONS

Parameter

Power Supply Voltage

Symbol

Min

1.7

Typ

Max

1.9

Unit

V

Note

VDD

VIH

VIL

1.8

Input High Level

1.3

-

VDD+0.3

0.5

V

Input Low Level

-0.3

1.4

V

Output High Voltage(IOH=-2mA)

Output Low Voltage(IOL=2mA)

VOH

VOL

VDD

V

VSS

0.4

V

Note: 1. The input level of SRAM pin is to follow the SRAM DC specification.

JTAG AC TEST CONDITIONS

Parameter

Input High/Low Level

Symbol

VIH/VIL

TR/TF

Min

1.3/0.5

1.0/1.0

0.9

Unit

V

Note

Input Rise/Fall Time

ns

V

Input and Output Timing Reference Level

Note: 1. See SRAM AC test output load on page 11.

1

JTAG AC Characteristics

Parameter

TCK Cycle Time

Symbol

Min

50

20

5

Max

Unit

Note

tCHCH

tCHCL

tCLCH

tMVCH

tCHMX

tDVCH

tCHDX

tSVCH

tCHSX

tCLQV

-

ns

TCK High Pulse Width

TCK Low Pulse Width

TMS Input Setup Time

TMS Input Hold Time

TDI Input Setup Time

TDI Input Hold Time

-

5

-

5

-

5

-

SRAM Input Setup Time

SRAM Input Hold Time

Clock Low to Output Valid

5

-

5

-

0

10

JTAG TIMING DIAGRAM

TCK

tCHCH

tCHCL

tCLCH

tMVCH

tCHMX

TMS

TDI

tDVCH

tSVCH

tCHDX

tCHSX

PI

(SRAM)

tCLQV

TDO

Dec. 2002

Rev 0.7

- 18 -

K7R323684M

K7R321884M

K7R320884M

Preliminary

1Mx36 & 2Mx18 & 4Mx8 QDR^TMII b4 SRAM

165 FBGA PACKAGE DIMENSIONS

15mm x 17mm Body, 1.0mm Bump Pitch, 11x15 Ball Array

B

Top View

A

C

Side View

D

A

G

E

B

F

Bottom View

H Æ

E

Symbol

Value

15 ± 0.1

17 ± 0.1

1.3 ± 0.1

0.35 ± 0.05

Units

Note

Symbol

Value

1.0

Units

mm

Note

A

B

C

D

mm

E

F

14.0

mm

G

H

10.0

mm

0.45 ± 0.05

mm

Dec. 2002

Rev 0.7

- 19 -


型号：	K7R320884M-FC13
厂家：	SAMSUNG
描述：	QDR SRAM, 4MX8, 0.5ns, CMOS, PBGA165, 15 X 17 MM, 1 MM PITCH, FBGA-165 静态存储器
文件：	总19页 (文件大小：204K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

K7R320884M-FC13 [SAMSUNG]

相关型号：

K7R320884M-FC16

K7R320884M-FC20

K7R320884M-FC200

K7R320884M-FC250

K7R320982C

K7R320982C-EC200

K7R320982C-EC20T

K7R320982C-EC250

K7R320982C-EC25T

K7R320982C-EC300

K7R320982C-EC30T

K7R320982C-EI200