M381L3223CT1-LA2 [SAMSUNG]
Synchronous DRAM Module, 32MX72, 0.75ns, CMOS, DIMM-184;型号: | M381L3223CT1-LA2 |
厂家: | SAMSUNG |
描述: | Synchronous DRAM Module, 32MX72, 0.75ns, CMOS, DIMM-184 动态存储器 内存集成电路 |
文件: | 总16页 (文件大小:97K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
256MB DDR SDRAM MODULE
(32Mx72 based on 32Mx8 DDR SDRAM)
Unbuffered 184pin DIMM
72-bit ECC/Parity
Revision 0.0
September. 2001
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
Revision History
Revision 0 (Sep 2001)
1. First release for internal usage
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
M381L3223CT1 DDR SDRAM 184pin DIMM
32Mx72 DDR SDRAM 184pin DIMM based on 32Mx8
GENERAL DESCRIPTION
FEATURE
• Performance range
The Samsung M381L3223CT1 is 32M bit x 72 Double Data
Rate SDRAM high density memory modules based on 4th gen
of 256Mb DDR SDRAM respectively.
Part No.
Max Freq.
Interface
M381L3223CT1-C(L)B3 167MHz(6.0ns@CL=2.5)
M381L3223CT1-C(L)A2 133MHz(7.5ns@CL=2)
M381L3223CT1-C(L)B0 133MHz(7.5ns@CL=2.5)
M381L3223CT1-C(L)A0 100MHz(10ns@CL=2)
The Samsung M381L3223CT1 consists of nine CMOS 32M x 8
bit with 4banks Double Data Rate SDRAMs in 66pin TSOP-
II(400mil) packages mounted on a 184pin glass-epoxy sub-
strate. Four 0.1uF decoupling capacitors are mounted on the
printed circuit board in parallel for each DDR SDRAM. The
M381L3223CT1 is Dual In-line Memory Modules and intended
for mounting into 184pin edge connector sockets.
SSTL_2
• Power supply : Vdd: 2.5V ± 0.2V, Vddq: 2.5V ± 0.2V
• Double-data-rate architecture; two data transfers per clock cycle
• Bidirectional data strobe(DQS)
• Differential clock inputs(CK and CK)
Synchronous design allows precise cycle control with the use
of system clock. Data I/O transactions are possible on both
edges of DQS. Range of operating frequencies, programmable
latencies and burst lengths allow the same device to be useful
for a variety of high bandwidth, high performance memory sys-
tem applications.
• DLL aligns DQ and DQS transition with CK transition
• Programmable Read latency 2, 2.5 (clock)
• Programmable Burst length (2, 4, 8)
• Programmable Burst type (sequential & interleave)
• Edge aligned data output, center aligned data input
• Auto & Self refresh, 7.8us refresh interval(8K/64ms refresh)
• Serial presence detect with EEPROM
• PCB : Height 1250 (mil), double sided component
PIN CONFIGURATIONS (Front side/back side)
PIN DESCRIPTION
Pin Front Pin Front Pin Front Pin Back Pin Back Pin
Back
Pin Name
A0 ~ A12
Function
Address input (Multiplexed)
1
2
3
4
5
6
7
8
9
10
11
12
13
VREF 32
DQ0 33 DQ24 63
VSS 34 VSS 64
DQ1 35 DQ25 65
DQS0 36 DQS3 66
A5
62 VDDQ 93
VSS
DQ4
DQ5
124
125
126
VSS
A6
DQ28
DQ29
VDDQ 158
DM3
A3
DQ30
VSS
DQ31
CB4
CB5
154
155
156
157
/RAS
DQ45
VDDQ
/CS0
*/CS1
DM5
/WE
DQ41
/CAS
VSS
DQS5
DQ42
94
95
96
97
98
99
BA0 ~ BA1
Bank Select Address
Data input/output
DQ0 ~ DQ63
CB0 ~ CB7
VDDQ 127
Check bit(Data-in/data-out)
Data Strobe input/output
DM0
DQ6
DQ7
VSS
NC
128
129
130
131
132
133
134
DQ2 37
VDD 38 VDD
A4
67
68
159
160
161
162
163
164
165
DQS0 ~ DQS8
VSS
CK0,CK0~ CK2, CK2 Clock input
DQ3 39 DQ26 69
DQ43 100
VDD 101
*/CS2 102
DQ48 103
DQ46
DQ47
*/CS3
VDDQ
DQ52
DQ53
NC
CKE0
CS0
Clock enable input
NC
NC
VSS
DQ8 43
DQ9 44
40 DQ27 70
Chip select input
41
42
A2
VSS
A1
71
72
73
74
75
76
NC
*A13
RAS
Row address strobe
Column address strobe
Write enable
DQ49 104 VDDQ 135
CAS
CB0
CB1
VSS
/CK2
CK2
105
106
107
DQ12
DQ13
DM1
VDD
DQ14
DQ15
136
137
138
139
140
141
VDDQ 166
WE
14 DQS1 45
CK0
/CK0
VSS
DM8
A10
CB6
VDDQ 173
CB7
KEY
167
168
169
170
171
172
DM0 ~ DM8
VDD
Data - in mask
15 VDDQ 46 VDD
16 CK1
17 /CK1 48
18 VSS 49
19 DQ10 50
20 DQ11 51
21 CKE0 52
22 VDDQ
23 DQ16 53 DQ32 84
24 DQ17 54 VDDQ 85
25 DQS2 55 DQ33 86
26
27
VDD
DM6
47 DQS8 77 VDDQ 108
Power supply (2.5V)
Power Supply for DQS(2.5V)
Ground
A0
78
79
80
81
DQS6 109
DQ50 110
DQ51 111 *CKE1 142
VSS 112 VDDQ 143
DQ54
DQ55
VDDQ
NC
DQ60
DQ61
VSS
VDDQ
VSS
CB2
VSS
CB3
BA1
VREF
VDDSPD
Power supply for reference
82 VDDID 113
*BA2
DQ20
A12
VSS
DQ21
A11
DM2
VDD
DQ22
A8
144
174
175
176
177
178
179
180
181
182
183
Serial EEPROM Power
Supply (2.3V to 3.6V)
KEY
83
DQ56 114
DQ57 115
145
146
147
148
149
150
151
152
153
VSS
DQ36
DQ37
VDD
SDA
Serial data I/O
VDD
116
DM7
SCL
Serial clock
DQS7 117
DQ58 118
DQ59 119
DQ62
DQ63
VDDQ
SA0
SA1
SA2
VSS
A9
56 DQS4 87
57 DQ34 88
SA0 ~ 2
VDDID
NC
Address in EEPROM
VDD identification flag
No connection
DM4
28 DQ18 58
29 A7 59
30 VDDQ 60 DQ35 91
31 DQ19 61 DQ40 92
VSS
BA0
89
90
VSS
WP
SDA
SCL
120
121
122
123
DQ38
DQ39
VSS
*
These pins are not used in this module.
DQ23
DQ44
184 VDDSPD
SAMSUNG ELECTRONICS CO., Ltd. reserves the right to change products and specifications without notice.
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
Functional Block Diagram
CS0
DQS0
DM0
DQS4
DM4
DM
I/O 7
I/O 6
I/O 1
I/O 0
CS DQS
D4
CS DQS
DM
I/O 7
I/O 6
I/O 1
I/O 0
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
D0
I/O 5
I/O 4
I/O 3
I/O 2
I/O 5
I/O 4
I/O 3
I/O 2
DQS5
DM5
DQS1
DM1
* Clock Wiring
SDRAMs
DM
CS DQS
D5
CS DQS
D1
DM
Clock
Input
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
I/O 7
I/O 6
I/O 1
I/O 0
DQ8
DQ9
DQ10
DQ11
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CK0/CK0
CK1/CK1
CK2/CK2
3 SDRAMs
3 SDRAMs
3 SDRAMs
I/O 5
I/O 4
I/O 3
I/O 2
DQ12
DQ13
DQ14
DQ15
DQS6
DM6
*Clock Net Wiring
DQS2
DM2
Dram1
DM
CS DQS
D6
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS DQS
D 2
DQ48
DQ49
DQ50
DQ51
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
Cap
R=120W
Dram3
DQ52
DQ53
DQ54
DQ55
Card
Edge
Cap
Dram5
DQS3
DM3
DQS7
DM7
CS
Cap
DM
DQS
CS
D3
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQS
DQ56
DQ57
DQ58
DQ59
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ24
DQ25
DQ26
DQ27
D 7
DQ60
DQ61
DQ62
DQ63
DQ28
DQ29
DQ30
DQ31
DQS8
DM8
Serial PD
DM
I/O 7
I/O 6
I/O 1
I/O 0
CS DQS
D8
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
SCL
WP
SDA
A0
A1
A2
I/O 5
I/O 4
I/O 3
I/O 2
SA0 SA1 SA2
VDDSPD
SPD
D0 - D8
BA0-BA1: SDRAMs D0 - D8
A0-A13: SDRAMs D0 - D8
BA0 - BA1
Notes:
1. DQ-to-I/O wiring is shown as recom-
VDD/VDDQ
A0 - A13
D0 - D8 mended but may be changed.
VDD/VDDQ
D0 - D8
2. DQ/DQS/DM/CKE/CS relationships
VREF
VSS
0.1uF
0.1uF
0.1uF
D0 - D8
must be maintained as shown.
D0 - D8
D0 - D8
3. DQ, DQS, DM/DQS resistors: 22 Ohms.
VREF
VSS
D0 - D8
D0 - D8
4. VDDID strap connections
VDDID
Strap: see Note 4
(for memory device VDD, VDDQ):
STRAP OUT (OPEN): VDD = VDDQ
STRAP IN (VSS): VDD ¹ VDDQ.
VDDID
Strap: see Note 4
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
ABSOLUTE MAXIMUM RATINGS
Parameter
Voltage on any pin relative to Vss
Voltage on VDD supply relative to Vss
Voltage on VDDQ supply relative to Vss
Storage temperature
Symbol
VIN, VOUT
VDD
Value
-0.5 ~ 3.6
-1.0 ~ 3.6
-0.5 ~ 3.6
-55 ~ +150
9
Unit
V
V
V
VDDQ
TSTG
°C
W
Power dissipation
PD
Short circuit current
IOS
50
mA
Note :
Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
POWER & DC OPERATING CONDITIONS (SSTL_2 In/Out)
Recommended operating conditions(Voltage referenced to VSS=0V, TA=0 to 70°C)
Parameter
Supply voltage(for device with a nominal VDD of 2.5V)
I/O Supply voltage
Symbol
VDD
Min
2.3
Max
2.7
Unit
Note
VDDQ
2.3
2.7
V
V
I/O Reference voltage
VREF
VDDQ/2-50mV VDDQ/2+50mV
1
2
4
4
I/O Termination voltage(system)
Input logic high voltage
V
VREF-0.04
VREF+0.04
VDDQ+0.3
VREF-0.15
VDDQ+0.3
VDDQ+0.6
1.35
V
TT
VIH(DC)
VIL(DC)
VIN(DC)
VID(DC)
VIX(DC)
II
VREF+0.15
V
Input logic low voltage
-0.3
-0.3
0.3
1.15
-2
V
Input Voltage Level, CK and CK inputs
Input Differential Voltage, CK and CK inputs
Input crossing point voltage, CK and CK inputs
Input leakage current
V
V
3
5
V
2
uA
uA
Output leakage current
IOZ
-5
5
Output High Current(Normal strengh driver)
IOH
IOL
IOH
-16.8
16.8
-9
mA
mA
mA
;V
= V + 0.84V
TT
OUT
Output High Current(Normal strengh driver)
;V = V - 0.84V
OUT
TT
Output High Current(Half strengh driver)
;V = V + 0.45V
OUT
TT
Output High Current(Half strengh driver)
;V = V - 0.45V
IOL
9
mA
OUT
TT
Notes 1. Includes ± 25mV margin for DC offset on VREF, and a combined total of ± 50mV margin for all AC noise and DC offset on VREF,
bandwidth limited to 20MHz. The DRAM must accommodate DRAM current spikes on VREF and internal DRAM noise coupled
TO VREF, both of which may result in VREF noise. VREF should be de-coupled with an inductance of £ 3nH.
2.V is not applied directly to the device. V is a system supply for signal termination resistors, is expected to be set equal to
TT
TT
VREF, and must track variations in the DC level of VREF
3. VID is the magnitude of the difference between the input level on CK and the input level on CK.
4. These parameters should be tested at the pin on actual components and may be checked at either the pin or the pad in
simulation. The AC and DC input specifications are relative to a VREF envelop that has been bandwidth limited to 200MHZ.
5. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the dc level of the same.
6. These charactericteristics obey the SSTL-2 class II standards.
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
DDR SDRAM SPEC Items and Test Conditions
Recommended operating conditions Unless Otherwise Noted, TA=0 to 70°C)
Conditions
Symbol
IDD0
Typical
Worst
Operating current - One bank Active-Precharge;
-
-
tRC=tRCmin;tCK=100Mhz for DDR200, 133Mhz for DDR266A & DDR266B;
DQ,DM and DQS inputs changing twice per clock cycle;
address and control inputs changing once per clock cycle
Operating current - One bank operation ; One bank open, BL=4, Reads
- Refer to the following page for detailed test condition
IDD1
-
-
-
-
Percharge power-down standby current; All banks idle; power - down mode;
CKE = <VIL(max); tCK=100Mhz for DDR200, 133Mhz for DDR266A & DDR266B;
Vin = Vref for DQ,DQS and DM
IDD2P
Precharge Floating standby current; CS# > =VIH(min);All banks idle;
CKE > = VIH(min); tCK=100Mhz for DDR200, 133Mhz for DDR266A & DDR266B;
Address and other control inputs changing once per clock cycle;
Vin = Vref for DQ,DQS and DM
IDD2F
IDD2Q
-
-
-
-
Precharge Quiet standby current; CS# > = VIH(min); All banks idle;
CKE > = VIH(min); tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B;
Address and other control inputs stable with keeping >= VIH(min) or =<VIL(max);
Vin = Vref for DQ ,DQS and DM
Active power - down standby current ; one bank active; power-down mode;
CKE=< VIL (max); tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B;
Vin = Vref for DQ,DQS and DM
IDD3P
IDD3N
-
-
-
-
Active standby current; CS# >= VIH(min); CKE>=VIH(min);
one bank active; active - precharge; tRC=tRASmax; tCK = 100Mhz for DDR200,
133Mhz for DDR266A & DDR266B; DQ, DQS and DM inputs changing twice
per clock cycle; address and other control inputs changing once
per clock cycle
Operating current - burst read; Burst length = 2; reads; continguous burst;
One bank active; address and control inputs changing once per clock cycle;
CL=2 at tCK = 100Mhz for DDR200, CL=2 at tCK = 133Mhz for DDR266A, CL=2.5 at tCK =
133Mhz for DDR266B ; 50% of data changing at every burst; lout = 0 m A
IDD4R
IDD4W
-
-
-
-
Operating current - burst write; Burst length = 2; writes; continuous burst;
One bank active address and control inputs changing once per clock cycle;
CL=2 at tCK = 100Mhz for DDR200, CL=2 at tCK = 133Mhz for DDR266A,
CL=2.5 at tCK = 133Mhz for DDR266B ; DQ, DM and DQS inputs changing twice
per clock cycle, 50% of input data changing at every burst
Auto refresh current; tRC = tRFC(min) - 8*tCK for DDR200 at 100Mhz,
IDD5
-
-
-
-
-
-
10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh
Self refresh current; CKE =< 0.2V; External clock should be on;
tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B
IDD6
Orerating current - Four bank operation ; Four bank interleaving with BL=4
IDD7A
-Refer to the following page for detailed test condition
Typical case: VDD = 2.5V, T = 25’ C
Worst case : VDD = 2.7V, T = 10’ C
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
DDR SDRAM IDD spec table
B3(DDR333@CL=2.5) A2(DDR266@CL=2) B0(DDR266@CL=2.5) A0(DDR200@CL=2)
Symbol
Unit
Notes
typical
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
worst
945
typical
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
worst
765
typical
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
worst
765
typical
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
worst
720
IDD0
IDD1
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
1260
36
1125
27
1125
27
1080
27
IDD2P
IDD2F
IDD2Q
IDD3P
IDD3N
IDD4R
IDD4W
IDD5
288
243
243
207
TBD
333
TBD
288
TBD
288
TBD
270
540
450
450
405
1530
1665
1755
27
1395
1260
1485
27
1395
1260
1485
27
1215
1080
1350
27
Normal
Low power
IDD7A
IDD6
TBD
3150
TBD
2655
TBD
2655
TBD
2160
Optional
* Module IDD was calculated on the basis of component IDD and can be differently measured according to DQ loading cap.
< Detailed test conditions for DDR SDRAM IDD1 & IDD7A >
IDD1 : Operating current: One bank operation
1. Typical Case : Vdd = 2.5V, T=25’ C
2. Worst Case : Vdd = 2.7V, T= 10’ C
3. Only one bank is accessed with tRC(min), Burst Mode, Address and Control inputs on NOP edge are changing once
per clock cycle. lout = 0mA
4. Timing patterns
- DDR200(100Mhz, CL=2) : tCK = 10ns, CL2, BL=4, tRCD = 2*tCK, tRAS = 5*tCK
Read : A0 N R0 N N P0 N A0 N - repeat the same timing with random address changing
*50% of data changing at every burst
- DDR266B(133Mhz, CL=2.5) : tCK = 7.5ns, CL=2.5, BL=4, tRCD = 3*tCK, tRC = 9*tCK, tRAS = 5*tCK
Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing
*50% of data changing at every burst
- DDR266A (133Mhz, CL=2) : tCK = 7.5ns, CL=2, BL=4, tRCD = 3*tCK, tRC = 9*tCK, tRAS = 5*tCK
Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing
*50% of data changing at every burst
Legend : A=Activate, R=Read, W=Write, P=Precharge, N=NOP
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
IDD7A : Operating current: Four bank operation
1. Typical Case : Vdd = 2.5V, T=25’ C
2. Worst Case : Vdd = 2.7V, T= 10’ C
3. Four banks are being interleaved with tRC(min), Burst Mode, Address and Control inputs on NOP edge are not
changing. lout = 0mA
4. Timing patterns
- DDR200(100Mhz, CL=2) : tCK = 10ns, CL2, BL=4, tRRD = 2*tCK, tRCD= 3*tCK, Read with autoprecharge
Read : A0 N A1 R0 A2 R1 A3 R2 A0 R3 A1 R0 - repeat the same timing with random address changing
*100% of data changing at every burst
- DDR266B(133Mhz, CL=2.5) : tCK = 7.5ns, CL=2.5, BL=4, tRRD = 2*tCK, tRCD = 3*tCK
Read with autoprecharge
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing
*100% of data changing at every burst
- DDR266A (133Mhz, CL=2) : tCK = 7.5ns, CL2=2, BL=4, tRRD = 2*tCK, tRCD = 3*tCK
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing
*100% of data changing at every burst
Legend : A=Activate, R=Read, W=Write, P=Precharge, N=NOP
AC Operating Conditions
Max
Parameter/Condition
Symbol
Min
Unit
Note
Input High (Logic 1) Voltage, DQ, DQS and DM signals
Input Low (Logic 0) Voltage, DQ, DQS and DM signals.
Input Differential Voltage, CK and CK inputs
VIH(AC) VREF + 0.31
VIL(AC)
V
V
V
V
3
3
1
2
VREF - 0.31
VDDQ+0.6
VID(AC) 0.7
Input Crossing Point Voltage, CK and CK inputs
VIX(AC) 0.5*VDDQ-0.2
0.5*VDDQ+0.2
Note 1. VID is the magnitude of the difference between the input level on CK and the input on CK.
2. The value of V is expected to equal 0.5*V of the transmitting device and must track variations in the DC level of the same.
IX
DDQ
3. These parameters should be tested at the pim on actual components and may be checked at either the pin or the pad in simula-
tion. the AC and DC input specificatims are refation to a Vref envelope that has been bandwidth limited 20MHz.
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
AC OPERATING TEST CONDITIONS (VDD=2.5V, VDDQ=2.5V, TA= 0 to 70°C)
Parameter
Value
Unit
Note
Input reference voltage for Clock
0.5 * VDDQ
V
Input signal maximum peak swing
Input Levels(VIH/VIL)
1.5
VREF+0.31/VREF-0.31
VREF
V
V
V
V
Input timing measurement reference level
Output timing measurement reference level
Output load condition
Vtt
See Load Circuit
Vtt=0.5*VDDQ
RT=50W
Output
Z0=50W
VREF
=0.5*VDDQ
CLOAD=30pF
Output Load Circuit (SSTL_2)
Input/Output CAPACITANCE (VDD=2.5V, VDDQ=2.5V, TA= 25°C, f=1MHz)
Parameter
Symbol
Min
Max
Unit
Input capacitance(A0 ~ A12, BA0 ~ BA1,RAS,CAS, WE )
CIN1
51
60
53
53
26
8
pF
pF
pF
pF
pF
pF
pF
Input capacitance(CKE0)
CIN2
CIN3
44
44
21
6
Input capacitance( CS0)
Input capacitance( CLK0, CLK1,CLK2)
Input capacitance(DM0~DM8)
CIN4
CIN5
Data & DQS input/output capacitance(DQ0~DQ63)
Data input/output capacitance(CB0~CB7)
COUT1
COUT2
6
8
6
8
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
AC Timming Parameters & Specifications (These AC charicteristics were tested on the Component)
-TCA2(DDR266A) -TCB0(DDR266B) -TCA0 (DDR200)
Parameter
Symbol
Unit
Note
Min
65
Max
Min
65
Max
Min
70
80
48
20
20
15
2
Max
Row cycle time
tRC
tRFC
tRAS
tRCD
tRP
ns
ns
Refresh row cycle time
Row active time
75
75
45
120K
45
120K
120K
ns
RAS to CAS delay
20
20
ns
Row precharge time
20
20
ns
Row active to Row active delay
Write recovery time
tRRD
tWR
15
15
ns
2
2
tCK
tCK
tCK
ns
Last data in to Read command
Col. address to Col. address delay
tCDLR
tCCD
1
1
1
1
1
1
CL=2.0
CL=2.5
7.5
7.5
0.45
0.45
-0.75
-0.75
-
12
12
10
12
12
10
12
5
5
Clock cycle time
tCK
7.5
0.45
0.45
-0.75
-0.75
-
12
ns
Clock high level width
tCH
tCL
0.55
0.55
+0.75
+0.75
+0.5
1.1
0.55
0.55
+0.75
+0.75
+0.5
1.1
0.45
0.45
-0.8
-0.8
-
0.55
0.55
+0.8
+0.8
+0.6
1.1
tCK
tCK
ns
Clock low level width
DQS-out access time from CK/CK
tDQSCK
tAC
Output data access time from CK/CK
Data strobe edge to ouput data edge
Read Preamble
ns
tDQSQ
tRPRE
tRPST
tDQSS
tWPRES
tWPREH
tDSS
ns
5
2
0.9
0.4
0.75
0
0.9
0.4
0.75
0
0.9
0.4
0.75
0
tCK
tCK
tCK
ns
Read Postamble
0.6
0.6
0.6
CK to valid DQS-in
1.25
1.25
1.25
DQS-in setup time
DQS-in hold time
0.25
0.2
0.2
0.35
0.25
0.2
0.2
0.35
0.25
0.2
0.2
0.35
tCK
tCK
tCK
tCK
tCK
tCK
ns
DQS falling edge to CK rising-setup time
DQS falling edge from CK rising-hold time
DQS-in high level width
tDSH
tDQSH
DQS-in low level width
tDQSL
tDSC
tIS
0.35
0.9
0.35
0.9
0.35
0.9
DQS-in cycle time
1.1
1.1
1.1
Address and Control Input setup time
Address and Control Input hold time
Data-out high impedence time from CK/CK
0.9
0.9
1.1
6
6
tIH
0.9
0.9
1.1
ns
tHZ
tACmin - tACmax tACmin tACmax tACmin tACmax
400ps - 400ps - 400ps - 400ps - 400ps - 400ps
tACmin - tACmax tACmin tACmax tACmin tACmax
ps
ps
Data-out low impedence time from CK/CK
tLZ
400ps
- 400ps - 400ps - 400ps - 400ps - 400ps
Input Slew Rate(for input only pins)
Input Slew Rate(for I/O pins)
Output Slew Rate(x4,x8)
tSL(I)
tSL(IO)
tSL(O)
0.5
0.5
0.5
1.0
0.7
0.5
0.5
1.0
0.7
V/ns
V/ns
V/ns
V/ns
6
7
0.5
1.0
4.5
5
4.5
5
4.5
5
10
10
Output Slew Rate(x16)
tSL
0.7
(O)
Output Slew Rate Matching Ratio(rise to fall)
t
0.67
1.5
0.67
1.5
0.67
1.5
SLMR
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
-TCA2(DDR266A)
-TCB0(DDR266B)
-TCA0 (DDR200)
Parameter
Symbol
Unit Note
Min
15
Max
Min
15
Max
Min
16
Max
Mode register set cycle time
DQ & DM setup time to DQS
DQ & DM hold time to DQS
tMRD
tDS
ns
0.5
0.5
0.6
ns
ns
7,8,9
7,8,9
tDH
0.5
1.75
10
0.5
1.75
10
0.6
2
DQ & DM input pulse width
tDIPW
tPDEX
tXSW
tXSA
tXSR
ns
ns
Power down exit time
10
Exit self refresh to write command
Exit self refresh to bank active command
Exit self refresh to read command
95
116
80
ns
75
75
200
15.6
7.8
ns
4
200
15.6
7.8
200
15.6
7.8
Cycle
us
64Mb, 128Mb
Refresh interval time
256Mb
tREF
1
1
us
tHPmin
-tQHS
tHPmin
-tQHS
tHPmin
-tQHS
Output DQS valid window
Clock half period
tQH
tHP
-
-
-
ns
ns
5
tCLmin
or tCHmin
tCLmin
or tCHmin
tCLmin
or tCHmin
-
-
-
Data hold skew factor
tQHS
0.75
0.75
0.8
ns
DQS write postamble time
tWPST
0.25
0.25
0.25
tCK
3
Note : 1. Maximum burst refresh of 8
2. The specific requirement is that DQS be valid(High or Low) on or before this CK edge. The case shown(DQS going from
High_Z to logic Low) applies when no writes were previously in progress on the bus. If a previous write was in progress,
DQS could be High at this time, depending on tDQSS.
3. The maximum limit for this parameter is not a device limit. The device will operate with a great value for this parameter,
but system performance (bus turnaround) will degrade accordingly.
4. A write command can be applied with tRCD satisfied after this command.
5. For registered DINNs, tCL and tCH are ³ 45% of the period including both the half period jitter (tJIT(HP)) of the PLL and the half
period jitter due to crosstalk (t JIT(crosstalk)) on the DIMM.
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
6. Input Setup/Hold Slew Rate Derating
Input Setup/Hold Slew Rate
DtIS
(ps)
0
DtIH
(ps)
0
(V/ns)
0.5
0.4
+50
+100
+50
+100
0.3
This derating table is used to increase t /t in the case where the input slew rate is below 0.5V/ns. Input setup/hold slew rate
IS IH
based on the lesser of AC-AC slew rate and DC-DC slew rate.
7. I/O Setup/Hold Slew Rate Derating
I/O Setup/Hold Slew Rate
DtDS
(ps)
0
DtDH
(ps)
0
(V/ns)
0.5
0.4
+75
+150
+75
+150
0.3
This derating table is used to increase t /t in the case where the I/O slew rate is below 0.5V/ns. I/O setup/hold slew rate
DS DH
based on the lesser of AC-AC slew rate and DC-DC slew rate.
8. I/O Setup/Hold Plateau Derating
I/O Input Level
(mV)
DtDS
(ps)
DtDH
(ps)
+50
± 280
+50
This derating table is used to increase tDS/tDH in the case where the input level is flat below VREF ± 310mV for a duration of
up to 2ns.
9. I/O Delta Rise/Fall Rate(1/slew-rate) Derating
Delta Rise/Fall Rate
DtDS
(ps)
0
DtDH
(ps)
0
(ns/V)
0
±0.25
±0.5
+50
+100
+50
+100
This derating table is used to increase tDS/tDH in the case where the DQ and DQS slew rates differ. The Delta Rise/Fall Rate
is calated as 1/SlewRate1-1/SlewRate2. For example, if slew rate 1 = 5V/ns and slew rate 2 =.4V/ns then the Delta Rise/Fall
Rate =-0/5ns/V. Input S/H slew rate based on larger of AC-AC delta rise/fall rate and DC-DC delta rise/fall rate.
10. This parameter is fir system simulation purpose. It is guranteed by design.
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
AC Timming Parameters & Specifications (These AC charicteristics were tested on the Component)
-TCB3(DDR333)
Parameter
Symbol
Unit
Note
Min
60
Max
Row cycle time
tRC
tRFC
tRAS
tRCD
tRP
ns
ns
Refresh row cycle time
Row active time
72
42
70K
ns
RAS to CAS delay
18
ns
Row precharge time
18
ns
Row active to Row active delay
Write recovery time
tRRD
tWR
12
ns
15
ns
Last data in to Read command
tCDLR
1
tCK
ns
CL=2.0
CL=2.5
7.5
6
12
4
4
Clock cycle time
tCK
12
ns
Clock high level width
tCH
tCL
0.45
0.45
-0.6
-0.7
-
0.55
0.55
+0.6
+0.7
0.45
1.1
tCK
tCK
ns
Clock low level width
DQS-out access time from CK/CK
tDQSCK
tAC
Output data access time from CK/CK
Data strobe edge to ouput data edge
Read Preamble
ns
tDQSQ
tRPRE
tRPST
tDQSS
tWPRES
tWPRE
tWPST
tDSS
ns
4
0.9
0.4
0.75
0
tCK
tCK
tCK
ns
Read Postamble
0.6
CK to valid DQS-in
1.25
DQS-in setup time
2
3
Write Preamble
0.25
0.4
0.2
0.2
0.35
0.35
tCK
tCK
tCK
tCK
tCK
tCK
Write Postamble
0.6
DQS falling edge to CK rising-setup time
DQS falling edge from CK rising-hold time
DQS-in high level width
DQS-in low level width
tDSH
tDQSH
tDQSL
Address and Control Input setup/hold time
(fast slew rate)
tIS/tIH
tIS/tIH
0.75
0.8
ns
ns
Address and Control Input setup/hold time
(slow slew rate)
DQ and DM input setup time
tDS
tDH
tHZ
tLZ
0.45
0.45
-0.7
-0.7
ns
ns
ps
ps
DQ and DM input hold time
Data-out high impedence time from CK/CK
Data-out low impedence time from CK/CK
+0.7
+0.7
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
-TCB3(DDR333)
Unit Note
Parameter
Symbol
Min
Max
Mode register set cycle time
tMRD
tIPW
2
tCK
ns
Control & Address input pulse width
(for each input)
2.2
DQ & DM input pulse width(for each input)
Exit self refresh to non read command
Exit self refresh to read command
tDIPW
tXSNR
tXSRD
1.75
75
ns
ns
200
tCK
us
64Mb, 128Mb
Refresh interval time
15.6
1
1
4
tREFI
256Mb
7.8
us
Output DQS valid window
Clock half period
tQH
tHP
tHP-tQHS
-
-
ns
tCLmin
or tCHmin
ns
ns
ns
Data hold skew factor
tQHS
tRAP
0.55
DQS write postamble time
tRCD or
tRAS min
3
Auto Precharge Write recovery +
Precharge time
tDAL
(tWR/tCK) +
(tRP/tCK)
tCK
1. Maximum burst refresh of 8
2. The specific requirement is that DQS be valid(High or Low) on or before this CK edge. The case shown(DQS going from
High_Z to logic Low) applies when no writes were previously in progress on the bus. If a previous write was in progress,
DQS could be High at this time, depending on tDQSS.
3. The maximum limit for this parameter is not a device limit. The device will operate with a great value for this parameter,
but system performance (bus turnaround) will degrade accordingly.
4. For registered DINNs, tCL and tCH are ³ 45% of the period including both the half period jitter (tJIT(HP)) of the PLL and the half period
jitter due to crosstalk (tJIT(crosstalk)) on the DIMM.
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
(V=Valid, X=Don¢t Care, H=Logic High, L=Logic Low)
Command Truth Table
A11, A12
A9 ~ A0
COMMAND
CKEn-1
CKEn
CS
RAS
CAS
WE
BA0,1
A10/AP
Note
Register
Register
Extended MRS
H
H
X
X
H
L
L
L
L
L
L
L
L
L
OP CODE
OP CODE
1, 2
1, 2
3
Mode Register Set
Auto Refresh
H
L
L
L
H
X
X
Entry
3
Refresh
Self
Refresh
L
H
L
H
X
L
H
X
H
H
X
H
3
Exit
L
H
X
X
3
Bank Active & Row Addr.
H
H
V
V
Row Address
Column
Address
(A0~A9)
Read &
Column Address
Auto Precharge Disable
Auto Precharge Enable
Auto Precharge Disable
Auto Precharge Enable
L
H
L
4
4
L
H
L
H
Column
Address
(A0~A9)
Write &
Column Address
4
H
H
H
X
X
X
L
L
L
H
H
L
L
H
H
L
L
L
V
H
4, 6
7
Burst Stop
Precharge
X
Bank Selection
All Banks
V
X
L
X
H
5
H
L
X
V
X
X
H
X
V
X
X
H
X
V
X
X
H
X
V
X
V
X
X
H
X
V
Entry
Exit
H
L
L
H
L
Active Power Down
X
X
X
H
L
Entry
H
Precharge Power Down Mode
H
L
Exit
L
H
DM
H
H
X
X
8
9
9
H
L
X
H
X
H
No operation (NOP) : Not defined
X
Note : 1. OP Code : Operand Code. A0 ~ A12 & BA0 ~ BA1 : Program keys. (@EMRS/MRS)
2. EMRS/ MRS can be issued only at all banks precharge state.
A new command can be issued 2 clock cycles after EMRS or MRS.
3. Auto refresh functions are same as the CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1 : Bank select addresses.
If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected.
If both BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank B is selected.
If both BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected.
5. If A10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected.
6. During burst write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
7. Burst stop command is valid at every burst length.
8. DM sampled at the rising and falling edges of the DQS and Data-in are masked at the both edges (Write DM latency is 0).
9. This combination is not defined for any function, which means "No Operation(NOP)" in DDR SDRAM.
Rev. 0.0 Sep. 2001
184pin Unbuffered DDR SDRAM MODULE
M381L3223CT1
PACKAGE DIMENSIONS
Units : Inches (Millimeters)
5.25 ± 0.006
(133.350 ± 0.15)
0.118
(3.00)
5.077
(128.950)
1.25 ± 0.006
±0.15)
(31.75
A
B
2.500
0.10 M
C
B
A
0.145 Max
(3.67 Max)
2.55
(64.77)
1.95
(49.53)
0.050 ± 0.0039
(1.270± 0.10)
0.118
(3.00)
0.250
0.157
(4.00)
0.039 ± 0.002
(1.000 ± 0.050)
(6.350)
0.26
(6.62)
0.0787
R (2.00)
0.1496
(3.80)
0.0078 ±0.006
(0.20 ±0.15)
2.175
0.071
(1.80)
0.050
(1.270)
0.1575
(4.00)
0.10
Detail A
M
C
A
B
M
Detail B
Tolerances : ± 0.005(.13) unless otherwise specified.
The used device is 32Mx8 SDRAM, TSOP.
SDRAM Part NO : K4H560838C-TC
Rev. 0.0 Sep. 2001
相关型号:
©2020 ICPDF网 联系我们和版权申明