ISDF-10-S-R [SAMTEC]
Board Connector, 10 Contact(s), 1 Row(s), Female, Crimp Terminal, Socket;
| 型号： | ISDF-10-S-R |
| 厂家： | 
SAMTEC |
| 描述： | Board Connector, 10 Contact(s), 1 Row(s), Female, Crimp Terminal, Socket |
| 文件： | 总3页 (文件大小：210K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
FIG. 1
REVISION G
ISDF-07-S SHOWN
ISDF-XX-S-X
SEE NOTE 2
(No OF POS x .050) - .050
(TOL NON-ACCUM)
C1
NOTCH SPECIFICATION
No OF POSITIONS
.025 (TYP)
-R: RETENTION LATCH (AVAILABLE
ON POS -02 THRU -50)
(SEE SHEET 3, FIG 2)
+.002
-02 THRU -50
((No OF POS x .050) + .021)
-.005
(SEE NOTE 10)
R.001
"A"
.020 (TYP)
ROW SPECIFICATION
-S: SINGLE ROW
.200 .130
.0700
.0950
A
"A"
DO NOT
SCALE FROM
THIS PRINT
SEE NOTE 3
"B"
"B"
.033
.030
.0800±.0020
.050
"C"
.003
'D'
.030
SEE NOTE 4
.050
C7
R.010
(TYP)
.2180
.058
.077
C4
.4260
.415
.440
C6
.0410
R.005 (TYP)
.103
.003
C2
.0420
"C"
R.001
'E'
.0525
C3
.0260
C5
SECTION "A"-"A"
.0430
SECTION "B"-"B"
SECTION "C"-"C"
SEE NOTE 8
SEE NOTE 7
07 06 05 04 03 02 01
'F'
NOTES:
SEE NOTE 11
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGOS SHALL APPEAR AT LOCATIONS ON SURFACE SHOWN,
APPROXIMATELY .075 x .055 (BOTH SIDES).
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER
DESIGNATION LOCATED WHERE SHOWN.
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
4. IDENTIFICATION MARKS NOT TO PROTRUDE BEYOND .001 ABOVE THE SURFACE
OF THE INSULATOR MATERIAL.
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01 [0.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
.XXX: .003 [0.08]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
.XXXX: .0015 [0.038]
e-Mail info@SAMTEC.com
6. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.0015, UNLESS OTHERWISE STATED.
7. GATE PADS MUST BE RECESSED .005.
SHEET SCALE: 4:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
VECTRA S475, COLOR: BLACK
MAX REGRIND: 50%
.050" CL CRIMP WIRE SOCKET INSULATOR
DWG. NO.
8. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).
9. R.005 OPTIONAL.
10. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE, SEE ISDF-XX-S-M PRINT.
11. .025 DIA EJ PADS CAN BE LOCATED AT VENDORS DISCRETION.
ISDF-XX-S-X
GAYNOR 6/10/2008
MAX FLASH ALLOWED: .002
MAX GATE VESTIGE: .004
SHEET 1 OF 3
BY:
C:\EnterpriseVault\DWG\MISC\MKTG\ISDF-XX-S-X-MKT.SLDDRW
REVISION G
90°
.0120
.0220 SQ.
.040 SQ.
R.0025
(TYP)
.0075
C8
+.0015 SQ.
30°
.0350-.0010
DETAIL 'F'
SCALE 16 : 1
DETAIL 'E'
SCALE 16 : 1
DETAIL 'D'
SCALE 16 : 1
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
e-Mail info@SAMTEC.com
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.166667
.050" CL CRIMP WIRE SOCKET INSULATOR
DWG. NO.
ISDF-XX-S-X
GAYNOR 6/10/2008
SHEET 2 OF 3
C:\EnterpriseVault\DWG\MISC\MKTG\ISDF-XX-S-X-MKT.SLDDRW
BY:
REVISION G
.1020±.0020
((No OF POS x .050) + .015)
C11
.0800±.0020
.050
+.000
-.002
5°
"H"
.120
C9
'J'
.360±.002
.440 REF
G
FIG. 3
-R: RETENTION LATCH OPTION (SEE NOTE 10)
(APPLIES TO POSITIONS -02, -03 & -04 ONLY)
(SAME AS FIG. 2 EXCEPT AS SHOWN)
.1740
.020
"H"
.0300
.0190
.065
+.0010
-.0005
.0095
.1480
.0140±.0010
+.002
-.005
SECTION "H"-"H"
((No OF POS x .050) + .145)
R.004
(4 PLCS)
C10
((No OF POS x .0500) + .0700) .002
.015 X 45°
R.0020
(TYP)
'K'
.200
15°
.0270
DETAIL 'K'
SCALE 10 : 1
PROPRIETARY NOTE
.0022
45°
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
FIG. 2
-R: RETENTION LATCH OPTION (SEE NOTE 10)
(ISDF-05-S-R SHOWN)
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.005±.002 (TYP)
30°
(TYP)
(SAME AS FIG. 1 EXCEPT AS SHOWN)
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 6:1
.050" CL CRIMP WIRE SOCKET INSULATOR
DWG. NO.
DETAIL 'J'
SCALE 10 : 1
ISDF-XX-S-X
SHEET 3 OF 3
C:\EnterpriseVault\DWG\MISC\MKTG\ISDF-XX-S-X-MKT.SLDDRW
BY:
GAYNOR 6/10/2008
相关型号：
ISDF-15-D
Board Connector, 30 Contact(s), 2 Row(s), Female, Straight, 0.05 inch Pitch, Crimp Terminal, Locking, Black Insulator, Socket, ROHS COMPLIANT
SAMTEC
©2020 ICPDF网 联系我们和版权申明