RF047-01SP6-10RP9-0100 [SAMTEC]
Cable Assembly, LEAD FREE;
| 型号： | RF047-01SP6-10RP9-0100 |
| 厂家： | 
SAMTEC |
| 描述： | Cable Assembly, LEAD FREE 连接器 连接器支架 |
| 文件： | 总3页 (文件大小：347K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISION A
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
Pb
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
RX047-XXXXX-XXXXXX-XXXX
OPTION
OVERALL CABLE LENGTH
MILLIMETERS OF CABLE
0100 MIN. (SEE NOTE 8 & 9)
F: SEMI FLEXIBLE
R: SEMI RIGID
(SEE NOTE 10)
DO NOT
SCALE FROM
THIS PRINT
*
FIG 2
CABLE STRIPPING DIMENSIONS
PER CONFIGURATIONS
(SEE NOTES 12,13,14)
END 2 PLATING OPTION
CABLE CALL OUT
1: GOLD ALL COMPONENTS
6. ALTERNATE H GOLD / H GOLD / NICKEL
9. ALTERNATE HEAVY GOLD/MEDIUM GOLD
P: HEAVY GOLD / PASSIVATED STAINLESS STEEL
(SEE SHEET 2 FOR PLATING SPECIFICS)
(LEAVE BLANK FOR -SING OR -XXXX
END 2 PREPARATION)
047: CCA-047-X (.047" COAXIAL CABLE)
END 1 CONNECTOR
"A" mm
"B" mm
C
-10SP: HMHF1-P-C-XX-ST-C47 (SEE SHEET 2)
*
-10RP: HMHF1-P-C-XX-RA-C47 (SEE SHEET 2)
*
-01SP: SMA-P-C-XX-ST-C47 (SEE SHEET 3)
-92SJ: 292XX-J-C-XX-ST-C47 (SEE SHEET 3)
-92SP: 292XX-P-C-XX-ST-C47 (SEE SHEET 3)
*
*
END 2 CONNECTOR OR PREPARATION
-10SP: HMHF1-P-C-XX-ST-C47 (SEE SHEET 2)
-10RP: HMHF1-P-C-XX-RA-C47 (SEE SHEET 2)
-01SP: SMA-P-C-XX-ST-C47 (SEE SHEET 3)
-92SJ: 292XX-J-C-XX-ST-C47 (SEE SHEET 3)
-92SP: 292XX-P-C-XX-ST-C47 (SEE SHEET 3)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXX: STRIPPED AND TINNED (THIS END ONLY-
SEE NOTES 11-15, 18 & SHEET 2, FIG 3)
*
*
END 1 PLATING OPTION
"D" mm
C
1: GOLD ALL COMPONENTS
*
*
6. ALTERNATE H GOLD / H GOLD / NICKEL
9. ALTERNATE HEAVY GOLD/MEDIUM GOLD
P: HEAVY GOLD / PASSIVATED STAINLESS STEEL
(SEE SHEET 2 FOR PLATING SPECIFICS)
(SEE FIG 2) "B" FORMAT: X.X mm
(SEE FIG 2) "A" FORMAT: X.X mm
* = NOT RELEASED
DO NOT LEAVE ANY SPACE BLANK,
EACH MUST CONTAIN A
NUMERIC CHARACTER 0 THRU 9.
C
FIG 1
RX047-10SPX-10RPX-XXXX SHOWN
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. CABLE CUT LENGTH:
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2).
(SEE TABLE 1 FOR SUBTRACTORS)
C 3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS.
C
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1, THE TEST VOLTAGE FOR THE ASSEMBLY
SHOULD BE SET TO THE END OPTION WITH THE LOWEST TEST VOLTAGE RATING.
5. AFTER FINAL ELECTRICAL TESTS, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL -ET
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3040-M.
LOCK WASHERS AND NUTS TO BE SHIPPED UNASSEMBLED. GASKETS TO BE INSTALLED ON CABLE.
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS.
9. CABLE LENGTHS LONGER THAN 1000 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA.
10. MINIMUM BEND RADIUS FOR RX047 = 5.00 [.196],
c:\enterprisevault\DWG\MISC\MKTG\RX047-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
RR047 SUPPLIED AS STRAIGHT ASSEMBLY ONLY, WITH MAX LENGTH = 0585[23"].
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
12. DIM "A" AND "B" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm.
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A.
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B.
MILLIMETERS [INCHES].
TOLERANCES ARE:
DECIMALS
ANGLES
5
.X: 0.3 [.01]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
15. NOTE DELETED.
MATERIAL:
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
16. CONNECTORS TO BE ORIENTED ACCORDING TO C0-HD-WI-3048-M.
17. FOR BULKHEAD APPLICATIONS, THE END USER SHOULD TIGHTEN THE THREADED NUT TO 15
IN-LB MINIMUM.
SEE END 1 AND END 2 ASSEMBLY PRINTS
.047" CABLE ASSEMBLY
DWG. NO.
18. FOR STRIPPED AND TINNED OPTION, ONLY THE CENTER CONDUCTOR IS TINNED.
RX047-XXXXX-XXXXXX-XXXX
3/20/2013
SHEET 1 OF 3
BY: EMMA CHEN
REVISION A
* -10SP
(STRAIGHT PLUG)
(USE DRAWING No. HMHF1-P-C-XX-ST-C47
FOR ASSEMBLY INSTRUCTIONS)
*
*
*
*
PLATING
9: 30μ" MIN. GOLD CENTER CONTACT
10μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: HMHF1-P-C-HG-ST-C47)
* = NOT RELEASED
NOTE: ALL CRITICAL DIMENSIONS ON HMHF1-P-C-XX-ST-C47
THAT APPLY MUST BE VERIFIED.
* -10RP
(RIGHT ANGLE PLUG)
(USE DRAWING No. HMHF1-P-C-XX-RA-C47
FOR ASSEMBLY INSTRUCTIONS)
FIG 3
RX047-10SPX-2025-XXXX SHOWN
PLATING
9: 30μ" MIN. GOLD CENTER CONTACT
10μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: HMHF1-P-C-HG-RA-C47)
NOTE: ALL CRITICAL DIMENSIONS ON HMHF1-P-C-XX-RA-C47
THAT APPLY MUST BE VERIFIED.
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.047" CABLE ASSEMBLY
DWG. NO.
RX047-XXXXX-XXXXXX-XXXX
EMMA CHEN 3/20/2013
BY:
SHEET 2 OF 3
c:\enterprisevault\DWG\MISC\MKTG\RX047-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
-92SJ
-92SP
*
*
REVISION A
-01SP
(STRAIGHT JACK)
(STRAIGHT PLUG)
(STRAIGHT PLUG)
(USE DRAWING No. 292XX-J-C-XX-ST-C47
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. 292XX-P-C-XX-ST-C47
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. SMA-P-C-XX-ST-C47
FOR ASSEMBLY INSTRUCTIONS)
PLATING
PLATING OPTIONS
PLATING OPTIONS
6: 30μ" MIN. GOLD CENTER CONTACT
30μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-J-C-HH-ST-C47)
6: 30μ" MIN. GOLD CENTER CONTACT
30μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-P-C-HH-ST-C47)
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-HF-ST-C47)
9: 30μ" MIN. GOLD CENTER CONTACT
10μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-J-C-HG-ST-C47)
9: 30μ" MIN. GOLD CENTER CONTACT
10μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-P-C-HG-ST-C47)
NOTE: ALL CRITICAL DIMENSIONS ON SMA-P-C-XX-ST-C47
THAT APPLY MUST BE VERIFIED.
P: 30μ" MIN. GOLD CENTER CONTACT
P: 30μ" MIN. GOLD CENTER CONTACT
PASSIVATED STAINLESS STEEL OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PS-J-C-HP-ST-C47)
PASSIVATED STAINLESS STEEL OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PS-P-C-HP-ST-C47)
NOTE: ALL CRITICAL DIMENSIONS ON 292XX-J-C-XX-ST-C47
THAT APPLY MUST BE VERIFIED.
NOTE: ALL CRITICAL DIMENSIONS ON 292XX-P-C-XX-ST-C47
THAT APPLY MUST BE VERIFIED.
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.047" CABLE ASSEMBLY
DWG. NO.
RX047-XXXXX-XXXXXX-XXXX
EMMA CHEN 3/20/2013
BY:
SHEET 3 OF 3
c:\enterprisevault\DWG\MISC\MKTG\RX047-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
相关型号：
©2020 ICPDF网 联系我们和版权申明