RF178-01SB1-03SP2-1000 [SAMTEC]
Interconnection Device, LEAD FREE;
| 型号： | RF178-01SB1-03SP2-1000 |
| 厂家： | 
SAMTEC |
| 描述： | Interconnection Device, LEAD FREE 连接器 |
| 文件： | 总3页 (文件大小：614K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
RF178-XXXXX-XXXXXX-XXXX
REVISION M
OVERALL CABLE LENGTH
MILLIMETERS OF CABLE
0100 MIN. (SEE NOTE 8 & 9)
CABLE CALLOUT
178: CCA-178 (RG-178 COAXIAL CABLE)
FIG.2
CABLE STRIPPING DIMENSIONS
PER CONFIGURATIONS
END 2 PLATING OPTION
END 1 CONNECTOR
1: GOLD ALL COMPONENTS
2: GOLD / NICKEL COMBINATION
3: ALTERNATE GOLD / NICKEL
*(LEAVE BLANK FOR -SING OR -XXXXXX
END 2 PREPARATION)
(SEE TABLE 1)(SEE NOTES 12,13,14,15)
-01BJ: SMA-J-C-X-ST-BH2 (SEE SHEET 2)
-01BR: SMA-J-C-X-ST-BR2 (SEE SHEET 2)
-02SJ: MCX-J-C-X-ST-CA2 (SEE SHEET 2)
-02RP: MCX-P-C-XX-RA-CA2 (SEE SHEET 2)
-02SP: MCX-P-C-XX-ST-CA2 (SEE SHEET 2)
-03SP: MMCX-P-C-XX-ST-CA2 (SEE SHEET 2)
-03RP: MMCX-P-C-X-RA-CA2 (SEE SHEET 3)
-01SB: SMA-J-C-X-ST-SB2 (SEE SHEET 3)
-01SR: SMA-J-C-X-ST-SR2 (SEE SHEET 3)
"A" mm
"B" mm
"C" mm
C
END 2 CONNECTOR OR PREPARATION
-01BJ: SMA-J-C-X-ST-BH2 (SEE SHEET 2)
-01BR: SMA-J-C-X-ST-BR2 (SEE SHEET 2)
-02SJ: MCX-J-C-X-ST-CA2 (SEE SHEET 2)
-02RP: MCX-P-C-XX-RA-CA2 (SEE SHEET 2)
-02SP: MCX-P-C-XX-ST-CA2 (SEE SHEET 2)
-03SP: MMCX-P-C-XX-ST-CA2 (SEE SHEET 2)
-03RP: MMCX-P-C-X-RA-CA2 (SEE SHEET 3)
-01SB: SMA-J-C-X-ST-SB2 (SEE SHEET 3)
-01SR: SMA-J-C-X-ST-SR2 (SEE SHEET 3)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXXXX: STRIPPED AND TINNED (THIS END ONLY-
SEE NOTES 11-15 & SHEET 3, FIG. 3)
"D" mm
"E" mm
C
C
END 1 PLATING OPTION
1: GOLD ALL COMPONENTS
2: GOLD / NICKEL COMBINATION
3: ALTERNATE GOLD / NICKEL
(SEE SHEET 2 FOR PLATING SPECIFICS)
(SEE FIG. 2) "C" FORMAT: X.X mm
(SEE FIG. 2) "B" FORMAT: X.X mm
(SEE FIG. 2) "A" FORMAT: X.X mm
DO NOT LEAVE ANY SPACE BLANK,
EACH MUST CONTAIN A
NUMERIC CHARACTER 0 THRU 9
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. CABLE CUT LENGTH:
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2).
(SEE TABLE 1 FOR SUBTRACTORS)
C
C
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS.
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1.
5. AFTER FINAL ELECTRICAL TESTS, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL -ET
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3033-M.
-LOCKWASHERS, NUTS, AND GASKETS TO BE SHIPPED UNASSEMBLED.
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS.
C
9. CABLE LENGTHS LONGER THAN 1000 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA.
10. MINIMUM BEND RADIUS FOR RG178 = 10.2 [.40].
FIG. 1
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
12. DIM "A", "B", AND "C" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm.
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A.
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B.
RF178-02SJX-03RPX-XXXX SHOWN
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
Pb
F:\DWG\MISC\MKTG\RF178-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
15. PRODUCTION OF STRIP AND TIN FOR JACKET USE: E=A+B+C.
16. FOR -RA TO -RA, CONNECTORS SHOULD BOTH BE ORIENTED UP. (SEE SHEET 3, FIG. 4)
MILLIMETERS [INCHES].
TOLERANCES ARE:
DECIMALS
ANGLES
2
.X: 0.3 [.01]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
MATERIAL:
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
RF178 CABLE ASSEMBLY
SEE END 1 AND END 2 ASSEMBLY PRINTS
NO.
DWGR. F178-XXXXX-XXXXXX-XXXX
5/6/2005
SHEET 1 OF 3
BY: TIM P.
REVISION M
-01BJ
-01BR (REVERSED POLARITY)
-02SJ
(STRAIGHT BULKHEAD JACK)
(STRAIGHT BULKHEAD JACK)
(STRAIGHT JACK)
(USE DRAWING No. SMA-J-C-X-ST-BH2
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. SMA-J-C-X-ST-BR2
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. MCX-J-C-X-ST-CA2
FOR ASSEMBLY INSTRUCTIONS)
PLATING
PLATING
PLATING
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-J-C-H-ST-BH2)
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-J-C-H-ST-BR2)
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-J-C-H-ST-CA2)
NOTE: ALL CRITICAL DIMENSIONS ON SMA-J-C-X-ST-BH2
THAT APPLY MUST BE VERIFIED.
NOTE: ALL CRITICAL DIMENSIONS ON SMA-J-C-X-ST-BR2
THAT APPLY MUST BE VERIFIED.
NOTE: ALL CRITICAL DIMENSIONS ON MCX-J-C-X-ST-CA2
THAT APPLY MUST BE VERIFIED.
-02RP
-02SP
-03SP
(RIGHT ANGLE PLUG)
(STRAIGHT PLUG)
(STRAIGHT PLUG)
(USE DRAWING No. MCX-P-C-XX-RA-CA2
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. MCX-P-C-XX-ST-CA2
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. MMCX-P-C-XX-ST-CA2
FOR ASSEMBLY INSTRUCTIONS)
PLATING OPTIONS
PLATING OPTIONS
PLATING OPTIONS
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-P-C-H-RA-CA2)
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-P-C-H-ST-CA2)
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MMCX-P-C-H-ST-CA2)
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-P-C-HN-RA-CA2)
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-P-C-HN-ST-CA2)
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MMCX-P-C-HN-ST-CA2)
NOTE: ALL CRITICAL DIMENSIONS ON MCX-P-C-XX-RA-CA2
THAT APPLY MUST BE VERIFIED.
NOTE: ALL CRITICAL DIMENSIONS ON MCX-P-C-XX-ST-CA2
THAT APPLY MUST BE VERIFIED.
NOTE: ALL CRITICAL DIMENSIONS ON MMCX-P-C-XX-ST-CA2
THAT APPLY MUST BE VERIFIED.
F:\DWG\MISC\MKTG\RF178-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
RF178 CABLE ASSEMBLY
NO.
DWGR. F178-XXXXX-XXXXXX-XXXX
TIM P.
5/6/2005
SHEET 2 OF 3
BY:
REVISION M
-03RP
-01SB
-01SR (REVERSED POLARITY)
(RIGHT ANGLE PLUG)
(STRAIGHT BULKHEAD JACK)
(SEALED STRAIGHT BULKHEAD JACK)
(USE DRAWING No. MMCX-P-C-X-RA-CA2
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. SMA-J-C-X-ST-SB2
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. SMA-J-C-X-ST-SR2
FOR ASSEMBLY INSTRUCTIONS)
PLATING
PLATING
PLATING
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MMCX-P-C-H-RA-CA2)
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-J-C-H-ST-SB2)
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-J-C-H-ST-SR2)
NOTE: ALL CRITICAL DIMENSIONS ON MMCX-P-C-X-RA-CA2
THAT APPLY MUST BE VERIFIED.
NOTE: ALL CRITICAL DIMENSIONS ON SMA-J-C-X-ST-SB2
THAT APPLY MUST BE VERIFIED.
NOTE: ALL CRITICAL DIMENSIONS ON SMA-J-C-X-ST-SR2
THAT APPLY MUST BE VERIFIED.
FIG.3
FIG.4
RF178-02SPX-102148-XXXX SHOWN
RF178-02RPX-02RPX-XXXX SHOWN
(SEE NOTE 16)
F:\DWG\MISC\MKTG\RF178-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 5:1
RF178 CABLE ASSEMBLY
DWG. NO.
RF178-XXXXX-XXXXXX-XXXX
5/6/2005
SHEET 3 OF 3
BY: TIM P.
相关型号：
©2020 ICPDF网 联系我们和版权申明