RS316-01BJ2-01BJ3-0100 [SAMTEC]
Cable Assembly,;
| 型号： | RS316-01BJ2-01BJ3-0100 |
| 厂家： | 
SAMTEC |
| 描述： | Cable Assembly, 连接器 连接器支架 |
| 文件： | 总3页 (文件大小：693K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISION B
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
Pb
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
RS316-XXXXX-XXXXXX-XXXX
CABLE CALL OUT
OVERALL CABLE LENGTH
MILLIMETERS OF CABLE
0100 MIN. (SEE NOTE 8 & 9)
RS316: CCA-316-S (RG316 CABLE,
DOUBLE SHIELD)
DO NOT
SCALE FROM
THIS PRINT
FIG 2
CABLE STRIPPING DIMENSIONS
PER CONFIGURATIONS
END 1 CONNECTOR
END 2 PLATING OPTION
-01SP: SMA-P-C-XX-ST-CA1S (SEE SHEET 2)
1: GOLD ALL COMPONENTS
2: GOLD / NICKEL COMBINATION
3: ALTERNATE GOLD / NICKEL
(LEAVE BLANK FOR -SING OR -XXXXXX
END 2 PREPARATION)
(SEE TABLE 1)(SEE NOTES 12,13,14,15)
-01BJ: SMA-J-C-XX-ST-BH1S (SEE SHEET 3)
*
-02SP: MCX-P-C-XX-ST-CA1S (SEE SHEET 3)
*
-02SJ: MCX-J-C-XX-ST-CA1S (SEE SHEET 3)
*
"A" mm
"B" mm
"C" mm
C
-03SP: MMCX-P-C-XX-ST-CA1S (SEE SHEET 3)
*
-04BJ: BNC5-J-C-XX-ST-BH1S (SEE SHEET 3)
-05SP: TNC-P-C-XX-ST-CA1S (SEE SHEET 3)
*
*
END 2 CONNECTOR OR PREPARATION
-01SP: SMA-P-C-XX-ST-CA1S (SEE SHEET 2)
-01BJ: SMA-J-C-XX-ST-BH1S (SEE SHEET 3)
-02SP: MCX-P-C-XX-ST-CA1S (SEE SHEET 3)
-02SJ: MCX-J-C-XX-ST-CA1S (SEE SHEET 3)
-03SP: MMCX-P-C-XX-ST-CA1S (SEE SHEET 3)
-04BJ: BNC5-J-C-XX-ST-BH1S (SEE SHEET 3)
-05SP: TNC-P-C-XX-ST-CA1S (SEE SHEET 3)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXXXX: STRIPPED AND TINNED (THIS END ONLY-
SEE NOTES 11-15, 18 & SHEET 2, FIG 3)
END 1 PLATING OPTION
*
*
*
*
*
*
1: GOLD ALL COMPONENTS
2: GOLD / NICKEL COMBINATION
3: ALTERNATE GOLD / NICKEL
(SEE SHEET 2 FOR PLATING SPECIFICS)
"D" mm
"E" mm
C
C
* = NOT RELEASED
(SEE FIG 2) "C" FORMAT: X.X mm
(SEE FIG 2) "B" FORMAT: X.X mm
(SEE FIG 2) "A" FORMAT: X.X mm
DO NOT LEAVE ANY SPACE BLANK,
EACH MUST CONTAIN A
NUMERIC CHARACTER 0 THRU 9.
C
FIG 1
RS316-01SPX-01SPX-XXXX SHOWN
NOTES:
C
1.
2. CABLE CUT LENGTH:
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2).
REPRESENTS A CRITICAL DIMENSION.
(SEE TABLE 1 FOR SUBTRACTORS)
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS.
C 4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1.
C
5. AFTER FINAL ELECTRICAL TESTS, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL -ET
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3040-M.
LOCK WASHERS AND NUTS TO BE SHIPPED UNASSEMBLED. GASKETS TO BE INSTALLED ON CABLE.
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS.
9. CABLE LENGTHS LONGER THAN 1000 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA.
10. MINIMUM BEND RADIUS FOR RS316 = 12.8 [0.50]
C:\EnterpriseVault\DWG\MISC\MKTG\RS316-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
12. DIM "A", "B", AND "C" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm.
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A.
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
MILLIMETERS [INCHES].
TOLERANCES ARE:
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
5
.X: 0.3 [.01]
15. PRODUCTION OF STRIP AND TIN FOR JACKET USE: E=A+B+C.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XX: 0.13 [.005]
16. CONNECTORS TO BE ORIENTED ACCORDING TO C0-HD-WI-3048-M.
17. FOR BULKHEAD APPLICATIONS, THE END USER SHOULD TIGHTEN THE THREADED NUT TO 15
IN-LB MINIMUM.
.XXX: 0.051 [.0020]
MATERIAL:
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
SEE END 1 AND END 2 ASSEMBLY PRINTS
18. FOR STRIPPED AND TINNED OPTION, ONLY THE CENTER CONDUCTOR IS TINNED.
RG316 (DOUBLE SHIELD) CABLE ASSEMBLY
DWG. NO.
RS316-XXXXX-XXXXXX-XXXX
3/20/2013
SHEET 1 OF
3
BY: EMMA CHEN
FIG 3
REVISION B
RS316-01SPX-102148-XXXX SHOWN
*
*
*
*
*
*
-01SP
(STRAIGHT PLUG)
(USE DRAWING No. SMA-P-C-XX-ST-CA1S
FOR ASSEMBLY INSTRUCTIONS)
* = NOT RELEASED
PLATING
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-HF-ST-CA1S)
NOTE: ALL CRITICAL DIMENSIONS ON SMA-P-C-XX-ST-CA1S
THAT APPLY MUST BE VERIFIED.
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PURPOSE OTHER THAN THAT WHICH IT WAS
PHONE: 812-944-6733
FAX: 812-948-5047
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
RG316 (DOUBLE SHIELD) CABLE ASSEMBLY
DWG. NO.
RS316-XXXXX-XXXXXX-XXXX
C:\EnterpriseVault\DWG\MISC\MKTG\RS316-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
EMMA CHEN
3/20/2013
SHEET 2 OF
3
BY:
REVISION B
*-01BJ
*-02SP
*-02SJ
(STRAIGHT BULKHEAD JACK)
(STRAIGHT PLUG)
(STRAIGHT JACK)
(USE DRAWING No. SMA-J-C-XX-ST-BH1S
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. MCX-P-C-XX-ST-CA1S
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. MCX-J-C-XX-ST-CA1S
FOR ASSEMBLY INSTRUCTIONS)
PLATING
PLATING
1: 30μ" MIN. GOLD CENTER CONTACT
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
PLATING
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-J-C-HF-ST-BH1S)
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-J-C-HF-ST-CA1S)
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-P-C-HF-ST-CA1S)
NOTE: ALL CRITICAL DIMENSIONS ON SMA-J-C-XX-ST-BH1S
THAT APPLY MUST BE VERIFIED.
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
NOTE: ALL CRITICAL DIMENSIONS ON MCX-J-C-XX-ST-CA1S
THAT APPLY MUST BE VERIFIED.
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MCX-P-C-HN-ST-CA1S)
NOTE: ALL CRITICAL DIMENSIONS ON MCX-P-C-XX-ST-CA1S
THAT APPLY MUST BE VERIFIED.
*-04BJ
*-03SP
*-05SP
(STRAIGHT BULKHEAD JACK)
(STRAIGHT PLUG)
(STRAIGHT PLUG)
(USE DRAWING No. BNC5-J-C-XX-ST-BH1S
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. MMCX-P-C-XX-ST-CA1S
FOR ASSEMBLY INSTRUCTIONS)
(USE DRAWING No. TNC-P-C-XX-ST-CA1S
FOR ASSEMBLY INSTRUCTIONS)
PLATING
3: 10μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: TNC-P-C-GN-ST-CA1S)
PLATING
PLATING
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: MMCX-P-C-HF-ST-CA1S)
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: BNC5-J-C-HN-ST-BH1S)
NOTE: ALL CRITICAL DIMENSIONS ON TNC-P-C-XX-ST-CA1S
THAT APPLY MUST BE VERIFIED.
2: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3: 10μ" MIN. GOLD CENTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: MMCX-P-C-HN-ST-CA1S)
100μ" MIN. NICKEL OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: BNC5-J-C-GN-ST-BH1S)
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
NOTE: ALL CRITICAL DIMENSIONS ON MMCX-P-C-XX-ST-CA1S
THAT APPLY MUST BE VERIFIED.
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
NOTE: ALL CRITICAL DIMENSIONS ON BNC5-J-C-XX-ST-BH1S
THAT APPLY MUST BE VERIFIED.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
RG316 (DOUBLE SHIELD) CABLE ASSEMBLY
DWG. NO.
RS316-XXXXX-XXXXXX-XXXX
C:\EnterpriseVault\DWG\MISC\MKTG\RS316-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
EMMA CHEN
3/20/2013
SHEET 3 OF
3
BY:
相关型号：
©2020 ICPDF网 联系我们和版权申明