SMH-102-02-H-S [SAMTEC]

Board Connector, 2 Contact(s), 1 Row(s), Female, Right Angle, 0.1 inch Pitch, Surface Mount Terminal, Locking, Black Insulator, Socket, LEAD FREE;


型号：	SMH-102-02-H-S
厂家：	SAMTEC
描述：	Board Connector, 2 Contact(s), 1 Row(s), Female, Right Angle, 0.1 inch Pitch, Surface Mount Terminal, Locking, Black Insulator, Socket, LEAD FREE
文件：	总3页 (文件大小：217K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

REVISION AE

SMH-1XX-XX-XX-X-XX

NO. OF POSITIONS

OPTIONS

-02 THRU -36

(PER ROW)

-XX: INDICATES POSITION

POLARIZED (USE PK-06-N)

-TR: TAPE & REEL PACKAGING

(2 - 29 POSITIONS ONLY)

DO NOT

SCALE FROM

THIS PRINT

LEAD STYLE

((No OF POS x .100[2.54]

) + .020[.51]) .010[.25]

-02: SURFACE MOUNT

(USE C-8-03-X)

ROW SPECIFICATION

-22: LOW INSERTION FORCE

(USE C-17-03-X)

-D: DOUBLE ROW (USE SMH-50-D)

(SEE FIG 1)

-S: SINGLE ROW (USE SSW-50-S)

(SEE FIG 2, SHT 2)

POSITION 01

MAX SWAY

.031 0.79 x .016[.41]

REF (TYP)

(EITHER DIRECTION)

PLATING

-G: 20µ" OVER IN CONTACT AREA, FLASH GOLD ON TAIL

-T: TIN OVER, MATTE TIN ON TAIL

-S: 30µ" OVER IN CONTACT AREA, MATTE TIN ON TAIL

-F: 3µ" OVER IN CONTACT AREA, MATTE TIN ON TAIL

-H: 30µ" OVER IN CONTACT AREA, FLASH GOLD ON TAIL

-L: 10µ" OVER IN CONTACT AREA, MATTE TIN ON TAIL

-TM: TIN OVER, MATTE TIN ON TAIL

-SM: 30µ" OVER IN CONTACT AREA, MATTE TIN ON TAIL

-FM: 3µ" OVER IN CONTACT AREA, MATTE TIN ON TAIL

.335 8.51

REF

SECTION "A"-"A"

SMH-50-D

.285±.010 7.24±0.25

SEE TABLE 1

'C'

.195 4.95

REF

.100 2.54 REF

SEE NOTE 2

.045 1.15 REF

"A"

.028 0.72 REF

.135±.010 3.43±0.25

FIG 1

SMH-120-XX-XX-D SHOWN

SEE SHEET 2 FOR IN-PROCESS VIEWS

.006 [.15

TAILS ONLY, SEE NOTE 12

DETAIL 'C'

SCALE 3.5 : 1

NOTES:

REPRESENTS A CRITICAL DIMENSION.

PROPRIETARY NOTE

UNLESS OTHERWISE SPECIFIED,

DIMENSIONS ARE IN INCHES.

TOLERANCES ARE:

2. COPLANARITY: POSITIONS 02-24= .006[.15], POSITIONS 25-36= .008[.20].

3. BURR ALLOWANCE: .003[.08] MAX.

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

4. ONE POSITION WILL BE LOST FOR EVERY CUT MADE ON A SOCKET

STRIP: CUT FLASH TO BE .010 [.25] MAX WITH NO FLASH ALLOWED IN

HOLES OR EXTENDING BELOW LEADS

DECIMALS

ANGLES

.XX: .01[.3]

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail: info@SAMTEC.com code: 55322

DESCRIPTION:

.XXX: .005[.13]

5. MINIMUM PUSHOUT FORCE: 1.5 LB.

.XXXX: .0020[.051]

6. MAXIMUM ALLOWABLE BOW: .003[.08] INCH/INCH AFTER ASSEMBLY.

7. ENDWALLS AFTER CUTTING: .045 +/-.003.

SHEET SCALE: 2:1

MATERIAL:

DO NOT SCALE DRAWING

8. SHEAR TAILS TO DIMENSION SHOWN.

.100 [2.54] HORIZONTAL SMT SOCKET ASSEMBLY

9. CONTACT TAILS TO BE FLUSH TO .003[.08] ABOVE OR BELOW A DATUM LINE

MADE BY THE INSULATOR. (-DH ONLY)

INSULATOR: LCP, UL 94 VO, COLOR: BLACK

CONTACT: PHOSPHOR BRONZE

DWG. NO.

10. NOTE DELETED.

11. POSITIONS 4 OR LESS SHOULD BE LAYER PACKAGED UNLESS OTHERWISE NOTED IN THE PART CALLOUT.

12. STRAIGHTNESS APPLIES TO FULL STRIPS ONLY.

SMH-1XX-XX-XX-X-XX

SHEET 1 OF 3

BY:

BRATCHER 2/5/99

F:\DWG\MISC\MKTG\SMH-1XX-XX-XX-X-XX-MKT.SLDDRW

REVISION AE

.394 10.01

'D'

SEE NOTE 9

(-DH ONLY)

.394 10.01

IN-PROCESS 1

.135±.010 3.43±0.25

MUST FILL WITH DIE SIDE OF PIN FACING DOWN, PINS ARE

STAMPED WITH A SQUARE INDICATOR MARK ON DIE SIDE

IN-PROCESS 3

.350 .010

(SEE NOTE 8)

.145±.010 3.68±0.25

(SEE NOTE 8)

.006 [.15]

TAILS ONLY, SEE NOTE 12

IN-PROCESS 2

.045 1.15 REF

.135±.010 3.43±0.25

IN-PROCESS 4

MUST FILL WITH DIE SIDE OF PIN FACING DOWN, PINS ARE

STAMPED WITH A SQUARE INDICATOR MARK ON DIE SIDE

.003 0.08

.006 [.15]

TAILS ONLY, SEE NOTE 12

DETAIL 'E'

SCALE 4 : 1

IN-PROCESS 5

TAILS MUST BE WITHIN +/-.003 WITH RESPECT TO

EACH OTHER.

'E'

SSW-50-S

.095 2.41 REF

SEE TABLE 1

SEE NOTE 2

.045 1.15 REF

.135±.010 3.43±0.25

FIG 2

SMH-120-XX-XX-S SHOWN

(SAME AS FIG 1, UNLESS OTHERWISE STATED)

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail: info@SAMTEC.com code: 55322

DESCRIPTION:

.394 10.01

DO NOT SCALE DRAWING

SHEET SCALE: 2:1

.100 [2.54] HORIZONTAL SMT SOCKET ASSEMBLY

.140±.010 3.56±0.25

(SEE NOTE 8)

DWG. NO.

IN-PROCESS 1

SMH-1XX-XX-XX-X-XX

IN-PROCESS 2

SHEET 2 OF 3

F:\DWG\MISC\MKTG\SMH-1XX-XX-XX-X-XX-MKT.SLDDRW

BY: BRATCHER 2/5/99

REVISION AE

POSITION 01

USER DIRECTION OF REELING

POCKET NOT DETAILED

-TR PACKAGING VIEW

ALL POCKETS DESIGNED PRIOR TO REVISION T, PART ORIENTATION SHOULD FOLLOW EXISTING POCKET

DESIGN.

AFTER REVISION T, ALL POCKETS ARE TO FOLLOW STANDARD ORIENTATION:

PIN #1 CLOSEST TO THE ROUND SPROCKET HOLES.

SEE NOTE 11

TUBE PACKAGING

PT-1-24-03-29

PT-1-24-01-30

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail: info@SAMTEC.com code: 55322

DESCRIPTION:

DO NOT SCALE DRAWING

SHEET SCALE: 2:1

.100 [2.54] HORIZONTAL SMT SOCKET ASSEMBLY

DWG. NO.

SMH-1XX-XX-XX-X-XX

SHEET 3 OF 3

F:\DWG\MISC\MKTG\SMH-1XX-XX-XX-X-XX-MKT.SLDDRW

BY:

BRATCHER 2/5/99

相关型号：