TFM-128-02-S-D-TR [SAMTEC]

Board Connector, 56 Contact(s), 2 Row(s), Male, Straight, Surface Mount Terminal,;


型号：	TFM-128-02-S-D-TR
厂家：	SAMTEC
描述：	Board Connector, 56 Contact(s), 2 Row(s), Male, Straight, Surface Mount Terminal,
文件：	总5页 (文件大小：1936K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

NOTES:

TFM-1XX-XX-XXX-X-XXX

REVISION EC

1. MINIMUM PUSHOUT FORCE TO BE 12 OZ RETENTION FOR CONTACTS AND WELD TABS.

2. COPLANARITY: .004[.10] = POS 02 THRU 26

.006[.15] = POS 27 THRU 50

OPTION

No OF POSITIONS

-A: ALIGNMENT PIN (USE TFM-XX-D-XX-A,

SEE TABLE 1) (SEE FIG. 8 SHEET 3)

(NOT AVAILABLE FOR -RA OR -REX)

-LC: LOCKING CLIP (USE LC-05-TM)SEE NOTE 16

(NOT AVAILABLE FOR -RA OR -REX)

(SEE FIG. 10 SHEET 3) (SEE NOTE 13)

-P: PICK AND PLACE PAD (USE PPP-04)

(AVAILABLE IN ALL POSITIONS

EXCEPT -05 WITH -WT)

3. NOTE DELETED.

LEAD STYLE -01: (-02 THRU -50 ALL

REPRESENTS A CRITICAL DIMENSION.

POSITIONS AVAILABLE)

5. [ ] DIMENSIONS ARE IN MILLIMETERS.

LEAD STYLE -02: (-02 THRU -50 ALL

POSITIONS AVAILABLE)

DO NOT

SCALE FROM

THIS PRINT

6. MEASURED FROM BEND.

7. DIMENSION CHANGED PER REVISION AD.

ALL OTHER LEAD STYLES: (-5 THRU -50 MULTIPLES OF 5)

LEAD STYLES -11, -12 POS 12, 16, 17 ALSO AVAILABLE

LEAD STYLES -21, -22, -31, -32

CONTACT ENGINEERING FOR INFORMATION.

8. SIDES OF PLASTIC BODIES ON ALL LEAD STYLES EXCEPT

THE -01 & -02 WILL BE SOLID, NOT RIBBED.

POS 12 AND 13 ALSO AVAILABLE

9. MEASURE FROM TIPS OF PIN.

(NOT AVAILABLE FOR -RA OR -REX,

SEE FIG. 7 SHEET 3)

10. NOTE DELETED.

LEAD STYLE

11. .003[.08] MAXIMUM TERMINAL BURR.

-RA: RIGHT ANGLE

THROUGH HOLE

-01, -03 (SEE FIG. 1)

-11, -13 (SEE FIG. 1)

-21,-23 (SEE FIG. 1)

-31 (SEE FIG. 1)

SURFACE MOUNT

12. .005 MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS.

13. MINIMUM LOCKING CLIP RETENTION TO BE 8 OZS.

14. THIS FEATURE ONLY PRESENT ON -01 &-02 LEAD STYLES.

15. AVAILABLE IN -05, -07, -10, -15, -20, -25 & -30 POS. ONLY.

16.DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC OPTION IS NOT

COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL PLACEMENT

FOR ALL ASSEMBLIES WITH THE –LC OPTION.

(AVAILABLE ONLY IN LEAD STYLE: -01

SEE FIG. 5, SHEET 2)

-02 (SEE FIG. 2)

-12 (SEE FIG. 2)

-22 (SEE FIG. 2)

-32 (SEE FIG. 2)

-TR: TAPE AND REEL (SEE FIG. 4, SHEET 5)

-SA: STAKED ALIGNMENT PIN (SEE FIG. 9,

SHEET 3)(NOT AVAILABLE FOR

-RA OR -RE)

PLATING SPECIFICATION

-K: POLYIMIDE FILM (SEE FIG. 3)

(NOT AVAILABLE FOR -RA OR -REX)

-WT: WELD TABS (USE WT-25-XX-T)

(AVAILABLE ON -01 AND -02 LEAD

STYLES ONLY) (SEE FIG. 6 SHEET 2)

-S: SELECTIVE, 30 Au / 50 Ni MIN ON CONTACT,

MATTE TIN TAIL

(No. OF POSITIONS x .050[1.27]) + .125[3.18] REF

(No. OF POSITIONS x .050[1.27]) + .025[.64] REF

-L: LIGHT SELECTIVE, 15 Au / 50 Ni MIN ON

CONTACT, MATTE TIN TAIL

-F: FLASH GOLD, 3 Au / 50 Ni MIN ON CONTACT,

MATTE TIN TAIL

(NOT AVAILABLE WITH -A, -LC,

-RA, OR -SA OPTIONS)

.110 2.79

-H: HEAVY GOLD, 30 Au / 50 Ni MIN ON

CONTACT, 3 Au / 50 Ni MIN ON TAIL

-SM: SELECTIVE, 30 Au / 50 Ni MIN ON CONTACT,

MATTE TIN TAIL

-RE1: RIGHT ANGLE ELEVATED .062 PCB

(USE TFM-XX-D-01-RE, NOT AVAILABLE

WITHOUT -WT, AVAILABLE IN LEAD

STYLE -01 ONLY, -05 THRU -50 POS)

(SEE FIG. 11, SHEET 4) (SEE NOTE 15)

-RE2: RIGHT ANGLE ELEVATED .093 PCB

(USE TFM-XX-D-01-RE, NOT AVAILABLE

WITHOUT -WT, AVAILABLE IN LEAD

STYLE -01 ONLY, -05 THRU -50 POS)

(SEE FIG. 11, SHEET 4) (SEE NOTE 15)

-SN: SOLDER NAIL FOR .062 BOARD

(TFM-XX-D-01-SN AND WT-27-01-T)

(SEE FIG.12, SHT 3)

REF

-LM: LIGHT SELECTIVE, 15 Au / 50 Ni MIN ON

CONTACT, MATTE TIN TAIL

.155 3.94

REF

-FM: FLASH GOLD, 3 Au / 50 Ni MIN ON CONTACT,

MATTE TIN TAIL

-STL: SELECTIVE, 30 Au / 50 Ni MIN ON CONTACT,

TIN/LEAD (90/10+/-5%) TAIL

.075 1.91

REF

.050 1.27

REF

.225 5.72

REF

BODY SPECIFICATION

-D: DOUBLE ROW

SEE NOTE 14

(ONLY AVAILABLE WITH -02 LEAD STYLE)

(NOT AVAILABLE WITH OPTIONS -A, -LC,

-RA, -SA, -WT, -RE1 OR -RE2)

.050 1.27

(No. OF POSITIONS x .050[1.27]) - .050[1.27]

2 MAX TOE

(TYP)

-SN2: SOLDER NAIL FOR .093 BOARD

(TFM-XX-D-01-SN AND WT-27-02-T)

(SEE FIG.12, SHT 3)

.018 [0.46

.135 3.43 REF

MAX SWAY

(TYP)

"A"

(ONLY AVAILABLE WITH -02 LEAD STYLE)

(NOT AVAILABLE WITH OPTIONS -A, -LC,

-RA, -SA, -WT, -RE1 OR -RE2)

.096 2.44

.1635 4.153

(SEE NOTE 7)

"D" REF

REF

"A" REF

SEE NOTE 8

.010 0.25 REF

.014 0.36 REF

"C" ^+.004[.10]

-.002[.05]

"J" ± .003 [0.08]

"A"

MAX SWAY (TYP)

C17

.050 1.27

MAX TOE (TYP)

(No. OF POSITIONS x .050[1.27]) - .050[1.27]

IN-PROCESS

FIGURE 1

THROUGH HOLE

-01, -03, -11, -13, -21, -23, -31

SECTION "A"-"A"

PROPRIETARY NOTE

UNLESS OTHERWISE SPECIFIED,

DIMENSIONS ARE IN INCHES.

TOLERANCES ARE:

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

DECIMALS

ANGLES

.XX: .01 [.3]

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail info@SAMTEC.com code 55322

.XXX: .005 [.13]

.XXXX: .0020 [.051]

SHEET SCALE: 2.5:1

MATERIAL:

DO NOT SCALE DRAWING

DESCRIPTION:

INSULATOR:

.050 X .050 TERMINAL STRIP

LCP, UL 94-VO

COLOR: BLACK

DWG. NO.

TFM-1XX-XX-XXX-X-XXX

TERMINAL: PHOSPHOR BRONZE

SHEET 1 OF 5

BY:

B RAY

7-10-2007

F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-X-XXX-MKT.SLDDRW

FIGURE 3

FIGURE 2

SURFACE MOUNT

REVISION EC

-K: POLYIMIDE FILM PAD

-02, -12, -22, -32

.216±.005 5.49±0.13

(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

"E"

(SEE TABLE 1)

"A" ^+.012[.30]

"B"

-.000[.00]

90°

C11

"S"

SEE NOTE 2

(SEE NOTE)

"B"

SEE NOTE 8

"R"

SEE NOTE 14

FLUSH TO .012 [.30] MAX

(SEE NOTE 6)

(-12, -22 & -32 STYLES)

(SEE NOTE)

C10

(-02 STYLE ONLY)

MAX SWAY

(TYP)

NOTE: “R” = OVERALL LENGTH (REF)

“S” = {(“R” - .216[5.49] /2} ±.020[.51]

.235 5.97

MAX

01 03

SECTION "B"-"B"

SEE NOTE 14

No. OF POSITIONS x .050) -.050[1.27]

(TOL ACCUM ±.005[.13] OVER 50 POS.)

FIGURE 5

FIGURE 6

-RA OPTION

-WT OPTION

DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

TERMINAL 2

TERMINAL 1

"C"

(No. OF POSITIONS X .050[1.27]) + .263[6.68] REF

WT-25-04-T

TFM-XX-D-01-WT

"D"

.075 1.91 REF

"C"

NOTCH TO BE

90°

C13

.014 0.36 REF

.093 2.35 (TYP)

C14

ORIENTED AS SHOWN

.020 0.51

C16

.010 0.25

REF (TYP)

(SEE NOTE 9)

.025 0.64

REF (TYP)

"A" REF

C15

.050 1.27

(No. OF POSITIONS x .050[1.27]) + .154[3.91]

(SEE NOTE 9)

SECTION "D"-"D"

SECTION "C"-"C"

MAX SWAY (TYP)

IN-PROCESS 1

IN-PROCESS 2

(ORIENT I.D. MARK AS SHOWN)

(FOR -RA OPTION ONLY)

.422 10.72

TERMINAL 1

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

.422 10.72

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail info@SAMTEC.com code 55322

TERMINAL 2

TERMINAL 1

TERMINAL 2

DESCRIPTION:

DO NOT SCALE DRAWING

SHEET SCALE: 2:1

90°

.050 X .050 TERMINAL STRIP

CARRIER STRIP

I.D. MARK

.075 1.91 REF

.020 0.51

DWG. NO.

TFM-1XX-XX-XXX-X-XXX

"A" REF

SHEET 2 OF 5

F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-X-XXX-MKT.SLDDRW

BY:

B RAY

7-10-2007

FIGURE 7

FIGURE 8

-A OPTION

REVISION EC

-P OPTION

DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

(PAD TO BE POSITIONED ON C.L. AS SHOWN)

DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

"M"

(SEE NOTE)

C17

"P"

(SEE NOTE)

.045 1.14

REF

(No. OF POSITIONS x .050[1.27]) + .075[1.91]

.394 10.01

REF

.050 1.27

REF

R.025 [0.64]

REF

*PPP-04

.225 5.72

REF

.050 1.27

"E"

FIGURE 9

-SA OPTION: STAKED ALIGNMENT PIN

DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

SECTION "E"-"E"

NOTE: “M” = (No. OF POSITIONS X .050[1.27]) + .125[3.18] (REF)

WITH -WT “M” = (No. OF POSITIONS X .050[1.27]) + .263[6.68] (REF)

“P” = {(“M” - .394[10.01]) /2} ±.020[.51]

* NOTCH ON PAD TO BE ON SAME END

AS THE NOTCH IN THE TFM BODY

.035 0.89

REF

SM-A5

.050 1.27

(No. OF POSITIONS x .050[1.27]) + .075[1.91]

MAX SWAY (TYP)

TABLE 4

FIGURE 12

-SNX: SOLDER NAIL

DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

OPTION

-SN

-SN2

"B"

.071[1.80]

.106[2.69]

FIGURE 10

-LC OPTION

DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

(NOT AVAILBLE ON -RA)

(No. OF POSITIONS x .050[1.27]) + .275 REF

FLUSH TO .005[0.13]

ABOVE

TFM-XX-D-01-SN

"K"

(TFM-1XX-02-D-LC)

LC-05-TM

"B" REF

.075 1.91 REF

C18

"K"

WT-27-XX-T

.050 1.27

.026 0.66 REF

(2PLCS)

.056 1.42 REF

(No. OF POSITIONS x .050[1.27]) + .175[4.45]

MAX SWAY (TYP)

.010 0.25 REF

2 MAX SWAY (TYP)

MAX SWAY

(TYP)

SECTION "K"-"K"

(No. OF POSITIONS x .050[1.27]) + .075[1.91]±.002[.05]

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail info@SAMTEC.com code 55322

DESCRIPTION:

DO NOT SCALE DRAWING

SHEET SCALE: 2:1

.050 X .050 TERMINAL STRIP

DWG. NO.

TFM-1XX-XX-XXX-X-XXX

F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-X-XXX-MKT.SLDDRW

BY:

B RAY

7-10-2007

SHEET 3 OF 5

FIGURE 11

IN-PROCESS 1

REVISION EC

-REX: RIGHT ANGLE ELEVATED

(ORIENT I.D. MARK AS SHOWN)

(FOR -RA OPTION ONLY)

TFM-120-XX-XXX-D-RE2 SHOWN

DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1

.775 19.69

.555 14.10

REF

.014 0.36 REF

"A" REF

TERMINAL 2

TERMINAL 1

.220 5.59 REF

I.D. MARK

IN-PROCESS 2

TFM-XX-D-01-RE

.255 6.48 REF

.555 14.10

"J"

TERMINAL 2

(SEE TABLE 1)

.225 5.72 REF

"F" REF

TERMINAL 1

(SEE TABLE 1)

.010 0.25

REF (TYP)

.075 1.91

C20

MAX SWAY (TYP)

"J"

(SEE NOTE 9)

90°

(No. OF POSITIONS x .050[1.27]) + .154[3.91]

90°

C19

.020 0.50

C21

"F"

(SEE NOTE 9)

(No. OF POSITONS x .050[1.27]) + .263[6.68] REF

.020 0.50

(SEE NOTE 9)

"A" REF

TERMINAL 1

(SEE TABLE 1)

IN-PROCESS 3

"H"

TERMINAL 2

(SEE TABLE 1)

C22

"G"

"F"

.025 0.64 REF

.089 2.26 REF

.097 2.46

90°

.075 1.91

(SEE NOTE 9)

SECTION "J"-"J"

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733

FAX: 812-948-5047

code 55322

e-Mail info@SAMTEC.com

DESCRIPTION:

DO NOT SCALE DRAWING

SHEET SCALE: 2:1

.050 X .050 TERMINAL STRIP

DWG. NO.

TFM-1XX-XX-XXX-X-XXX

F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-X-XXX-MKT.SLDDRW

BY:

B RAY

7-10-2007

SHEET 4 OF 5

REVISION EC

PARTS TO BE PACKAGED IN TUBES AS SHOWN

LOADING DIRECTION ARROW

POLARIZATION NOTCH

LOADING DIRECTION ARROW

POLARIZATION NOTCH

PT-1-24-XX-09

(SEE TABLE 2)

PT-1-24-18-09

(SEE TABLE 2)

FIGURE 4

-TR: TAPE AND REEL

LOADING DIRECTION ARROW

POLARIZATION NOTCH

ROUND HOLES

PAD NOTCH

PART NOTCH

PT-1-24-05-17

(SEE TABLE 2)

OBLONG HOLES

USER DIRECTION OF UN-REELING

POCKET NOT DETAILED

LOADING DIRECTION ARROW

PT-1-24-09F-109

(SEE TABLE 2)

NOTE:

PARTS TO BE PACKAGED WITH THE LOADING DIRECTION ARROW

POINTED IN SAME DIRECTION AS THE ARROW ON TUBE.

PROPRIETARY NOTE

THIS DOCUMENT CONTAINS INFORMATION

CONFIDENTIAL AND PROPRIETARY TO

SAMTEC, INC. AND SHALL NOT BE REPRODUCED

OR TRANSFERRED TO OTHER DOCUMENTS OR

DISCLOSED TO OTHERS OR USED FOR ANY

PURPOSE OTHER THAN THAT WHICH IT WAS

OBTAINED WITHOUT THE EXPRESSED WRITTEN

CONSENT OF SAMTEC, INC.

520 PARK EAST BLVD, NEW ALBANY, IN 47150

PHONE: 812-944-6733 FAX: 812-948-5047

e-Mail info@SAMTEC.com code 55322

POLARIZATION NOTCH

DESCRIPTION:

DO NOT SCALE DRAWING

SHEET SCALE: 2:1

.050 X .050 TERMINAL STRIP

DWG. NO.

TFM-1XX-XX-XXX-X-XXX

F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-X-XXX-MKT.SLDDRW

BY:

B RAY

7-10-2007

SHEET 5 OF 5

相关型号：