WTSM-27-SV [SAMTEC]
Board Connector, 27 Contact(s), 1 Row(s), Female, Straight;
| 型号： | WTSM-27-SV |
| 厂家： | 
SAMTEC |
| 描述： | Board Connector, 27 Contact(s), 1 Row(s), Female, Straight 连接器 |
| 文件： | 总2页 (文件大小：309K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISION
WTSM-XX-SV-XX
C2
No OF POSITIONS x .1000
No OF POSITIONS
02-50
OPTION (MOLDED ALIGNMENT PIN)
-XX: # OF POSITIONS PER ROW
ROW SPECIFICATION
-Sv: SINGLE VERTICAL
ON FINISHED PART
(4 POS. MIN.)
C4
{(No OF POSITIONS x .1000) - .2000} +.002/-.003
C5
(No OF POSITIONS x .1000) - .1000
"A"
"A"
'C'
.1000
SECTION "A"-"A"
NOT RELEASED
FOR PRODUCTION
USE FOR QUOTING, PRELIMINARY
DESIGN, PROTOTYPING AND
INFORMATIONAL PURPOSES ONLY
THIS DESIGN HAS
NOT BEEN APPROVED
BY ENGINEERING
DO NOT DISTRIBUTE
THIS PRINT
.1000
"N"
"N"
'D'
SEE NOTE 3
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGO SHALL APPEAR ON SURFACE SHOWN, APPROXIMATELY .0625 x .040
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A NUMBER
DESIGNATION LOCATED WHERE SHOWN.
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE
SURFACE OF THE PART.
C1
.0245±.0005
.0175±.001 (TYP)
.0650 TYP
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MAX ALLOWABLE BOW: SEE TABLE 1
.0247±.0005
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01 [.3]
DETAIL 'D'
SCALE 5 : 1
.XXX: .005 [.13]
.XXXX: .0020 [.051]
SHEET SCALE: 2.5:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
DWG. NO.
VECTRA E130i, COLOR: NATURAL
MAX REGRIND: 50%
100 CL SINGLE ROW TERMINAL
WTSM-XX-SV-XX
MAX FLASH ALLOWED: .002, .004 IN CUT GROOVE AREA
MAX GATE VESTIGE: .002
BY:
B. PERRY
8/22/06
SHEET 1 OF 2
F:\DWG\SW\Exisprod\Compnt\BODIES\100\wtsm-xx-sv-xx.slddrw
REVISION 0
'H'
.2000 TYP.
C3
((No OF POS PER ROW ON FINISHED PART) -2) x .1000
'F'
.0050 (TYP)
45°
.0450 (TYP)
.0150
.0520
.0800
.0120±.0005
.0180
SECTION "N"-"N"
SCALE 5 : 1
DETAIL 'C'
SCALE 5 : 1
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
.1000
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 2.5:1
DETAIL 'F'
SCALE 5 : 1
100 CL SINGLE ROW TERMINAL
DWG. NO.
R (TYP)
WTSM-XX-SV-XX
DETAIL 'H'
SCALE 5 : 1
8/22/06
SHEET 2 OF 2
F:\DWG\SW\Exisprod\Compnt\BODIES\100\wtsm-xx-sv-xx.slddrw
BY:
B. PERRY
相关型号：
©2020 ICPDF网 联系我们和版权申明