SEL6210STH10D [SANKEN]
Round-type contact mount LEDs (for automatic insertion); 轮型接触贴装LED （自动插入）
| 型号： | SEL6210STH10D |
| 厂家： | 
SANKEN ELECTRIC |
| 描述： | Round-type contact mount LEDs (for automatic insertion) |
| 文件： | 总4页 (文件大小：111K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Round-type contact mount LEDs (for automatic insertion)
■SEL6010 series (Standard type)
■SEL6014 series (Wide viewing angle)
SEL6210R
Outline drawing A
SEL6414E
Outline drawing B
4.5±0.5
3.5 1.0min
Cathode
23.0min
(1.7)
5.5±0.5
3.5 1.0min
Cathode
23.0min
(1.6)
3.5±0.1
2.5±0.1
0.4±0.1
Resin heap
0.8max
0.4±0.1
Resin heap
0.8max
■SEL6015 series (Narrow viewing angle)
Absolute maximum ratings (Ta=25°C)
SEL6915A
Outline drawing C
Symbol
IF
Unit
mA
mA
V
Ratings
30
100
3.5 1.0min
Cathode
23.0min
IFP
(1.7)
3.5±0.1
Resin burr
0.3max
VR
3
Top
Tstg
°C
–30 to +85
°C
–30 to +100
0.4±0.1
Resin heap
0.8max
●SEL6000 series LEDs pack-
aged on tapes can withstand
shocks caused by insertion ma-
chines; Thus, they can be con-
tact-mounted automatically on
circuit boards.
Recommended dimensions of
insertion holes on printed cir-
cuit boards
Cathode mark
ø
0.9 1.0
■External dimensions: Unit: mm Tolerance: ±0.3
2.54mm
Viewing angle
SEL6010 series
SEL6014 series
SEL6015 series
0°
0°
0°
30°
30°
30°
30°
30°
30°
60°
60°
60°
60°
60°
60°
90°
100%
90°
100%
90°
100%
90°
100%
90°
100%
90°
100%
50
0
50
50
0
50
50
0
50
Viewing angle of a non-diffused lens
Viewing angle of a non-diffused lens
Viewing angle of a non-diffused lens
0°
30°
30°
60°
60°
90°
100%
90°
100%
50
0
50
Viewing angle of a diffused lens
18
Electro-optical characteristics (Ta=25°C)
Display
form
Emitting
color
Outline
VF
(V)
IR
IV
λp
(nm) typ
∆λ
Type of lens
Type No.
(µA)
(mcd)
Condition
IF
Condition
VR
Condition
IF
drawing
(ø: mm)
typ
1.9
max
max
typ
12
25
15
45
5
(mA)
(V)
(mA)
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.5
●3.5
●3.5
●3.5
●3.5
●3.1
●3.1
●3.1
●3.1
●3.1
Red tinted, diffused
Red tinted, non-diffused
Green tinted, diffused
SEL6210R
SEL6210S
SEL6410G
SEL6410E
SEL6510G
SEL6510C
SEL6710Y
SEL6710K
SEL6810D
SEL6810A
SEL6910D
SEL6910A
SEL6214S
SEL6414E
SEL6514C
SEL6814A
SEL6914A
SEL6215S
SEL6415E
SEL6515C
SEL6815A
SEL6915A
630
35
High intensity red
Green
20
10
560
555
570
610
587
Green tinted, non-diffused
Green tinted, diffused
20
Pure green 2.0
Yellow
Un-tinted, non-diffused
Yellow tinted, diffused
16
5
A
2.5
10
50
3
40
35
Yellow tinted, non-diffused
Orange tinted, diffused
Orange tinted, non-diffused
Orange tinted, diffused
Orange tinted, non-diffused
Red tinted, non-diffused
Green tinted, non-diffused
Un-tinted, non-diffused
Orange tinted, non-diffused
Orange tinted, non-diffused
Red tinted, non-diffused
Green tinted, non-diffused
Un-tinted, non-diffused
Orange tinted, non-diffused
Orange tinted, non-diffused
15
4
Amber
1.9
10
6.5
14
10
12
6
33
35
20
Orange
630
560
555
610
587
630
560
555
610
587
High intensity red 1.9
20
10
Green
2.0
Pure green
2.5
2.5
10
10
50
50
3
3
B
C
5
35
33
35
Amber
1.9
5
Orange
30
50
18
30
40
High intensity red 1.9
Green
2.0
20
Pure green
20
Amber
1.9
35
33
Orange
■Using contact mount LEDs packaged on tapes
1. Printed circuit board
2. Insertion conditions
3. Soldering conditions
●One-side printed circuit board is recommended.
●If there are several SMD parts on the same printed circuit board, insert the LEDs after the adhesive for
other SMD parts hardened.
●Use low insertion pusher pressure, as much as possible.
●Cut and clinch: Panasert T pattern is recommended.
For N pattern, make the clinching angle of the LED’s anode as small as possible.
●Preheating must be less than 90°C (temperature on printed circuit board’s bottom surface) for no more
than two minutes
●Solder dipping must be made at a temperature of 250°C for no more than 3 seconds.
19
Taping of packaged LEDs with holder (for automatic insertion)
■TH12E
■TH10D
Outline drawing B
TH10D
Outline drawing A
TH12E
12.7±1.0
12.7±1.0
Component Alignment
0±0.2
Component Alignment
0±0.2
Marking (Black)
6.35±0.5
0±0.2
Marking (Black)
6.35±0.5
0±0.2
L = MIN 1.6
W = MIN 0.2
L = MIN 1.6
W = MIN 0.2
Holder
Holder
0.4±0.1
0.4±0.1
3.85±0.5
0.45±0.1
3.85±0.5
0.45±0.1
Tape
Tape
5.0±0.5 (Po)12.7±0.2
ø
4.0±0.2
Mounting Tape
5.0±0.5 (Po)12.7±0.2
ø
4.0±0.2
Mounting Tape
(Po): Cumulative pitch tolerance shall not exceed ±1.0mm over 20
consecutive pitches.
(Po): Cumulative pitch tolerance shall not exceed ±1.0mm over 20
consecutive pitches.
Tolerance: ±0.3
Tolerance: ±0.3
■External dimensions: Unit: mm Tolerance: ±0.3
●Eliminates the cumbersome need to attach holders.
●Available in heights of 12 mm, 10 mm and 8 mm with a luminous
area of 4.0 mm × 4.0 mm.
●Available in different colors.
●TH10D and TH12E are holders used for the SEL6010 series.
TH8F is a holder used for the SEL5020 and SEL5021 series.
●Available in radial taping configuration with a lead pitch of 5
mm allowing mounting by inserters.
20
Product list
■TH8F
Type No.
Emitting color
High intensity red
Green
SEL6210S TH12E
SEL6410E TH12E
SEL6510C TH12E
SEL6710K TH12E
SEL6810A TH12E
SEL6910A TH12E
SEL6210S TH10D
SEL6410E TH10D
SEL6510C TH10D
SEL6710K TH10D
SEL6810A TH10D
SEL6910A TH10D
SEL5220S TH8F
SEL5420E TH8F
SEL5520C TH8F
SEL5820A TH8F
SEL5920A TH8F
SEL5221S TH8F
SEL5421E TH8F
SEL5521C TH8F
SEL5821A TH8F
SEL5921A TH8F
Pure green
Yellow
Amber
Orange
Outline drawing C
TH8F
High intensity red
Green
6.0
4.0
Pure green
Yellow
Bent
(P
2
)
(P)
0±2.0
6.0
6.35±0.5
12.7±1.0
Amber
7.2
0±2.0
Marking (black)
Orange
High intensity red
Green
0.5
Pure green
Amber
Tape
Orange
4.0±0.2
High intensity red
Green
ø
(P0)12.7±0.2
5.0±0.5
Cathode
Paper mount
Pure green
Amber
Orange
■External dimensions: Unit: mm Tolerance: ±0.3
Quantity per box: 1,200
Recommended dimensions of insertion holes on printed circuit
boards (common)
(Po): The cumulative pitch error
2-
ø0.9~1.0
must be within ±1.0 for 2.0
LED insertion hole
5.0
pitches.
21
相关型号：
©2020 ICPDF网 联系我们和版权申明