LB11693JH_10 [SANYO]
24V Fan Motor Driver IC; 24V风扇马达驱动IC
| 型号： | LB11693JH_10 |
| 厂家： | 
SANYO SEMICON DEVICE |
| 描述： | 24V Fan Motor Driver IC |
| 文件： | 总12页 (文件大小：154K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Ordering number : ENA0606A
Monolithic Digital IC
LB11693JH
24V Fan Motor Driver IC
Overview
The LB11693JH is a three-phase brushless motor driver IC that uses a direct PWM drive technique to achieve highly
efficient drive. It is optimal for driving fuel pump motors and other miniature motors.
Functions
• Soft phase switching + Direct PWM drive
• PWM control based on both a DC voltage input (the CTL voltage) and a pulse input
• Provides a 5V regulator output
• One Hall-effect sensor FG output
• Built-in integrating amplifier
• Automatic recovery constraint protection circuit (on/off = 1/14), RD output
• Built-in current limiter circuit
• Built-in LVSD circuit
• Built-in thermal protection circuit
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Supply voltage range
Output current
Symbol
max
Conditions
Ratings
Unit
V
V
30
1.8
CC
I
max
T ≤ 500ms
A
O
Allowable power dissipation 1
Allowable power dissipation 2
Operating temperature
Storage temperature
Pd max1
Independent IC
0.9
W
W
°C
°C
Pd max2
Topr
Mounted on a specified board*
2.1
-40 to +85
-55 to +150
Tstg
* Mounted on a specified board: 114.3mm×76.1mm×1.6mm, glass epoxy
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer
's products or
equipment.
90110 SY 20100827-S00001 / D1306 MS IM 20060404-S00004 No.A0606-1/12
LB11693JH
Allowable Operating Ranges at Ta = 25°C
Parameter
Supply voltage range
Constant voltage output current
RD output current
Symbol
Conditions
Ratings
Unit
V
V
8 to 28
0 to -30
0 to 10
0 to 10
CC
IREG
IRD
mA
mA
mA
FG output current
IFG
Electrical Characteristics at Ta = 25°C, V
= VM = 24V
CC
Ratings
typ
Parameter
Symbol
Conditions
unit
min
max
Current drain 1
I
I
1
2
10
13.5
mA
mA
CC
Current drain 2
When STOP
4.0
5.5
CC
[Output Block]
Output saturation voltage 1
Output saturation voltage 2
Output leakage current
High side diode forward voltage 1
High side diode forward voltage 2
[5V Constant Voltage Output]
Output voltage
V
sat1
sat2
I
I
= 0.7A,V (SINK)+V (SOURCE)
O O
1.5
2.2
2.05
2.9
V
V
O
O
O
V
I
= 1.5A,V (SINK)+V (SOURCE)
O O
O
leak
100
1.65
2.5
μA
V
O
V
1
I
I
= 0.7A
= 1.5A
1.25
1.9
D
D
D
D
V
2
V
VREG
I
= -5mA
4.7
5.0
30
20
5.3
100
100
V
O
Line regulation
ΔVREG1
ΔVREG2
V
= 9.5 to 28V
mV
mV
CC
= -5 to -20mA
Load regulation
I
O
[Hall Amplifier]
Input bias current
IB(HA)
VHIN
VICM
VIOH
2
10
350
μA
mVp-p
V
Hall sensor input sensitivity
Common-mode input voltage range
Input offset voltage
Sine wave input
50
Differential input 50mVp-p
Design target value*
1.5
VREG-1.0
+20
-20
mV
[CSD Pin]
High-level output voltage
Low-level output voltage
External capacitor charge current
External capacitor discharge current
Charge/discharge current ratio
V
(CSD)
2.75
0.85
-3.3
0.09
3.0
1.0
3.25
1.15
-1.4
0.23
V
V
OH
V
(CSD)
OL
ICSD1
ICSD2
RCSD
-2.4
0.17
14
μA
μA
Charge current/discharge current
Times
[Undervoltage Protection Circuit (LVS Pin)]
Operating voltage
VSDL
3.6
4.1
3.8
4.3
0.5
4.0
4.5
V
V
V
Release voltage
VSDH
Hysteresis
ΔVSD
0.35
0.65
[Current Limiter Circuit]
Limiter voltage
VRF
V
-VM
CC
0.45
150
0.5
0.55
V
[Thermal Shutdown Operation]
Thermal shutdown operating
temperature
TSD
Design target value*
(junction temperature)
Design target value*
(junction temperature)
170
40
°C
°C
Hysteresis
ΔTSD
[CTL Amplifier]
Input offset voltage
VIO(CTL)
IB(CTL)
VICM
-10
-1
0
10
1
mV
μA
V
Input bias current
Common-mode input voltage range
High-level output voltage
Low-level output voltage
Open-loop gain
VREG-1.7
V
(CTL)
ITOC = -0.2mA
ITOC = 0.2mA
f(CTL) = 1kHz
VREG-1.2 VREG-0.8
0.8
V
OH
V
(CTL)
1.05
V
OL
G(CTL)
45
51
dB
*: Design target value and no measurement was made.
Continued on next page.
No.A0606-2/12
LB11693JH
Continued from preceding page.
Ratings
typ
Parameter
Symbol
Conditions
unit
min
max
[PWM Oscillator Circuit]
High-level output voltage
Low-level output voltage
Amplitude
V
(PWM)
2.75
3.0
3.25
V
V
OH
V
(PWM)
1.1
1.5
1.3
1.7
1.4
2.0
OL
V(PWM)
ICHG
Vp-p
μA
External capacitor charge current
Oscillator frequency
[TOC Pin]
VPWM = 2.1V
-125
15.5
-90
-70
f(PWM)
C = 2200pF
19.5
27.0
kHz
Input voltage 1
VTOC1
VTOC2
Output duty: 100%
2.72
1.07
2.72
1.07
3.08
1.21
3.0
1.3
3.30
1.45
2.90
1.27
3.30
1.45
V
V
V
V
V
V
Input voltage 2
Output duty: 0%
Input voltage 1L
VTOC1L
VTOC2L
VTOC1H
VTOC2H
Design target value*. 100% when VREG = 4.7V
Design target value*. 0% when VREG = 4.7V
Design target value*. 100% when VREG = 5.3V
Design target value*. 0% when VREG = 5.3V
2.80
1.17
3.20
1.33
Input voltage 2L
Input voltage 1H
Input voltage 2H
[RD Pin]
Low-level output voltage
Output leakage current
[FG Pin]
V
(RD)
IRD = 5mA
VRD = 28V
0.1
0.1
0.3
10
V
OL
IL(RD)
μA
Low-level output voltage
Output leakage current
[FGFIL Pin]
V
(FG)
IFG = 5mA
VFG = 28V
0.3
10
V
OL
IL(FG)
μA
Charge current
IFGFIL1
IFGFIL2
-7
3
-5
5
-3
7
μA
μA
Discharge current
[FG Amplifier Schmitt Block (IN1)]
Amplifier gain
G(FG)
Design target value*.
7
8
Times
mV
Hysteresis
V
(FG)
Design target value*. Input equivalent
IS
[S/S Pin]
High-level input voltage
Low-level input voltage
Input open voltage
Hysteresis
V
(SS)
2.0
0
VREG
1.0
V
V
IH
V
V
(SS)
(SS)
IL
2.6
0.16
2.9
0.25
100
3.2
V
IO
V
(SS)
0.34
130
V
IS
High-level input current
Low-level input current
[PWMIN Pin]
I
(SS)
IH
VS/S = VREG
VS/S = 0V
μA
μA
I
(SS)
IL
-170
-130
Input frequency range
High-level input voltage range
Low-level input voltage range
Input open voltage
Hysteresis
f(PI)
(PI)
50
VREG
1.0
kHz
V
V
2.0
0
IH
V
V
(PI)
(PI)
V
IL
2.6
0.16
2.9
0.25
100
3.2
V
IO
V
(PI)
0.34
130
V
IS
High-level input current
Low-level input current
[F/R Pin]
I
(PI)
IH
VPWMIN = VREG
VPWMIN = 0V
μA
μA
I
(PI)
-170
-130
IL
High-level input voltage
Low-level input voltage
Input open voltage
Hysteresis
V
(FR)
2.0
0
VREG
1.0
V
V
IH
V
V
(FR)
(FR)
IL
VREG-0.5
0.16
VREG
0.34
10
V
IO
V
(FR)
0.25
0
V
IS
High-level input current
Low-level input current
I
(FR)
IH
VF/R = VREG
VF/R = 0V
-10
μA
μA
I
(FR)
IL
-165
-115
*: Design target value and no measurement was made.
No.A0606-3/12
LB11693JH
Package Dimensions
unit : mm (typ)
3251
Pd max - Ta
Mounted on a specified board:
114.3mm×76.1mm×1.6mm glass epoxy
17.8
(6.2)
2.4
36
19
2.1
2.0
1.6
1.2
1.09
0.47
Independent IC
1
18
0.9
0.8
(0.5)
2.0
0.3
0.8
0.25
0.4
0
-40
-20
0
20
40
60
80
100
2.7
Ambient Temperature, Ta -°C
ILB01760
SANYO : HSOP36R(375mil)
Truth Table
F/R = ”L”
F/R = “H”
Source→Sink
IN1
H
H
H
L
IN2
L
IN3
IN1
L
IN2
H
H
L
IN3
L
1
2
3
4
5
6
OUT2→OUT1
OUT3→OUT1
OUT3→OUT2
OUT1→OUT2
OUT1→OUT3
OUT2→OUT3
H
L
L
L
H
H
H
L
H
H
H
L
L
L
L
H
H
H
L
L
H
H
L
L
H
L
Pin Assignment
36
35
34
33
32
31
30
29
28
27
25
24
23
22
21
20
19
26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Top view
No.A0606-4/12
LB11693JH
Block Diagram
FG
RD
V
CC
EI-
TOC
FG
CSD
RD FC
RD
LVS
-
CSD
CIRCUIT
FG
CIRCUIT
LVSD
TSD
EI+
CTL
+
V
CC
CTL AMP
VD
VM
Rd
Rf
CURR
LIM
PWM
PWM
OSC
COMP
PWMIN
CONTROL
CIRCUIT
OUT1
OUT2
OUT3
PWMIN
DRIVER
VREF
BGP
GND1
FILTER
HALL AMP
& MATRIX
5VREG
F/R
S/S
IN1
IN2
IN3
VREG
S/S
F/R FGFIL
GND2
VREG
Pin Functions
Pin
No.
34
36
2
Symbol
Pin Description
Equivalent Circuit
OUT1
OUT2
OUT3
GND2
Motor drive output
V
CC
VD
7
9
4
Motor drive output system ground
300Ω
VM
7
9
VD
VM
Low side output transistor drive current supply
2
4
34 36
Motor drive output power supply and output current
detection.
Connect a resistor (Rf) between this pin and V
.
CC
The output current is limited to a value determined
by the equation I
= VRF/Rf.
OUT
8
V
Power supply
CC
(Systems other than the motor drive output)
5V regulator output
10
VREG
V
CC
Connect a capacitor (about 0.1µF) between this pin and
ground for stabilization.
10
Continued on next page.
No.A0606-5/12
LB11693JH
Continued from preceding page.
Pin
Symbol
No.
Pin Description
Equivalent Circuit
11
LVS
Undervoltage protection voltage detection.
Connect this pin to VREG if the VREG level is to be
detected.
VREG
If the V
CC
series to set the detection level.
level is to be detected, insert a zener diode in
52kΩ
11
12
FGFIL
FG filter.
VREG
Normally, this IC will be used with this pin open.
Connect a capacitor between this pin and ground
if noise on the FG signal becomes a problem.
300Ω
12
14
15
16
FC
CSD
FG
Control loop frequency characteristics correction.
Connect a capacitor between this pin and ground.
VREG
300Ω
14
Constraint protection circuit operating time setting.
VREG
300Ω
15
One hall-effect sensor FG output.
(This is an open-collector output.)
VREG
16
Continued on next page.
No.A0606-6/12
LB11693JH
Continued from preceding page.
Pin
Symbol
No.
Pin Description
Equivalent Circuit
17
RD
Motor constrained state detection output
(This is an open-collector output.)
VREG
When the motor is constrained: high, when the motor is
turning: low.
17
18
PWM
IN
PWM pulse input.
VREG
When low the output will be on and when high the
outputs will be off. If this pin is used to control this IC,
connect EI- to ground and connect EI+ to TOC.
5kΩ
18
20
S/S
Start/stop control. Low: start, high or open: stop.
VREG
5kΩ
20
21
22
EI+
EI-
CTL amplifier noninverting input
CTL amplifier inverting input
VREG
300Ω
300Ω
22
21
23
TOC
PWM waveform comparator (CTL amplifier output)
VREG
23
PWM comparator
Continued on next page.
No.A0606-7/12
LB11693JH
Continued from preceding page.
Pin
Symbol
No.
Pin Description
Equivalent Circuit
25
PWM
PWM oscillator frequency setting.
VREG
Connect a capacitor between this pin and ground.
A frequency of about 20kHz can be set by using
a 2200pF capacitor.
200Ω
25
26
GND1
Ground
(For circuits other than the motor drive output system)
Hall effect sensor inputs
28
27
30
29
32
31
IN1+
IN1-
IN2+
IN2-
IN3+
IN3-
VREG
High when IN+ > IN-, low for the reverse state.
Signal inputs with an amplitude (differential) of at least
50mVp-p are desirable for the Hall inputs.
If noise is a problem, connect capacitors between
the IN+ and IN- inputs.
300Ω
300Ω
27 29 31
28 30 32
33
F/R
Forward/reverse control
VREG
Low: forward, high or open: reverse.
3.5kΩ
33
1,3
5,6
NC
No connection.
The NC pins may be used for wiring connections.
13,19
24,35
FRAME
Frame connection
The FRAME pin is connected internally to the IC surface
metal parts. Both must be used in the electrically open
state.
No.A0606-8/12
LB11693JH
LB11693JH Overview
1. Output Drive Circuit
The LB11693JH reduces motor vibration and noise by switching the output current smoothly when switching phases.
Since the Hall input waveform is used for the change in (slope of) the output current during phase switching, if the
slope of the Hall input waveform is too steep, the change in the output current during phase switching will also be too
steep and the effectiveness of this technique at lowering vibration and noise effect will be reduced. Thus the slope of
the Hall input waveform requires attention during application design.
Low side output transistor PWM switching is used for motor speed control. The drive output is adjusted by changing
the duty. The diodes between the outputs and VM used for the regenerative current when the PWM signal is in the
off state are built in.
If the slope (amplitude) of the Hall input waveform is large, and if used with a high current, the parasitic diodes
between the outputs and ground will operate due to the low side kickback during phase switching. If problems such
as disruption of the waveforms occur, connect either rectifying diodes or Schottky diodes between the outputs and
ground.
2. Power Supply Stabilization
Since the LB11693JH uses a control method based on PWM switching, the power supply lines are susceptible to
disruption. Electrolytic capacitors with an adequate capacitance for stabilization must be connected between V
CC
and ground. If diodes are inserted in the power supply lines to prevent destruction of the equipment if the power
supply is connected in reverse, the power supply lines will be particularly susceptible to disruption. In this case, even
larger capacitors must be used. The connected electrolytic capacitors must be located as close as possible to the IC
pins (V , VM, and GND2). If the electrolytic capacitors cannot be attached close to the pins due to problems with
CC
the heat sink or other issues, ceramic capacitors of about 0.1µF must be attached close to the pins.
3. VREG Pin
At the same time as being the 5V regulator output, the VREG pin is also the power supply for the IC internal control
circuits. Therefore, a capacitor of at least 0.1µF must be connected between the VREG pin and ground to stabilize the
control circuit power supply. The ground side of the connected capacitor must be connected to the GND1 pin with as
short a line as possible.
4. FC Pin
The capacitor connected to the FC pin is required to correct the control loop's frequency characteristics.
(It should be about 0.1μF.)
5. VD Pin
The VD pin supplies the low side output transistor drive current (a maximum of about 0.1A).
The IC internal power consumption is suppressed by connecting a resistor between the V
and VD pins and
CC
dividing power consumption due to the low side output transistor drive current with that resistor. Although the IC
internal power consumption due to the drive current can be reduced by lowering the VD pin voltage, a voltage of at
least 4V must be assured at the VD pin. Use a resistor in the range from about 50Ω (0.5W) to about 100Ω (1W)
between the V
and VD pins when the LB11693JH is used with V = 24V.
CC
CC
6. Hall Effect Sensor Input Signals
Signal inputs with an amplitude (differential) of at least 50mVp-p are required for the Hall inputs. If the output
waveforms are disrupted by noise, capacitors must be connected between the Hall input pins (the + and - sides).
7. Current Limiter Circuit
The current limiter circuit limits the peak value of the output current to a current determined by the equation I =
VRF/Rf (where VRF = 0.5V (typical), Rf = current detection resistor value). When the limiter operates, it suppresses
the current by PWM control of the low side output transistor at the PWM frequency determined by the external
capacitor connected to the PWM pin, in particular, by reducing the on duty.
No.A0606-9/12
LB11693JH
8. Forward/Reverse Switching
The LB11693JH was designed assuming that forward/reverse switching would not be performed while the motor is
operating. We recommend that the F/R pin be held fixed at either the low (forward) or high (reverse) level when the
motor is turning. Although it will be pulled up to the high level by an internal pull-up resistor (about 40kΩ) when left
open, this must be strengthened by an external resistor if fluctuations are large.
If the direction is switched while the motor is turning, large currents will flow due to the braking operation. The
LB11693JH's current limiter circuit, however, cannot limit this braking current. Therefore, forward/reverse switching
during motor rotation is only possible if the braking current is limited to a value under I max (1.8A) by the motor
O
coil resistance or other circuit or phenomenon. Furthermore, since through current will flow in the high and low side
transistors at the instant the switch occurs with switching that only uses the F/R pin, applications must provide a rive
off period for switching directions. A drive off period must be provided by either setting the IC to the stopped state
with the S/S pin or setting the PWM signal to the 0% duty state with the TOC and PWMIN pins, and the F/R pin
must only be switched during that period to prevent through current.
9. Power Saving Circuit
This IC can be set to a power saving state in which current consumption is reduced by setting it to the stopped state
with the S/S pin. The bias current to most of the circuits in the IC is cut off in this power saving state. Note, however,
that the 5V regulator output is still provided in the power saving state.
10. Notes on the PWM Frequency
The PWM frequency is determined by the capacitance (F) of the capacitor connected to the PWM pin.
fPWM≈1/ (23400×C)
A frequency in the range 15 to 25kHz is desirable for the PWM frequency. The ground side of the connected
capacitor must be connected to the GND1 pin by as short a line as possible.
11. Control Methods
The output duty can be controlled by either of the following methods.
• Comparison of the TOC pin voltage with the PWM oscillator waveform
This method determines the low side output transistor duty according to the result of comparing the TOC pin
voltage with the PWM oscillator waveform. The PWM duty will be 0% when the TOC pin voltage is under about
1.3V and will be 100% when that voltage is over about 3.0V.
Since the TOC pin is the output of the CTL amplifier, a control voltage cannot be directly input to the TOC pin.
Accordingly, the CTL amplifier is normally used as a full feedback amplifier (by connecting the EI- pin to the
TOC pin) and inputting a DC voltage to the EI pin (here the TOC voltage will be equal to the EI+ pin voltage).
When the EI+ pin voltage increases, the output duty will increase as well. Since the motor will be driven if the EI+
pin is in the open state, a pull-down resistor should be connected to the EI+ pin in applications where this is not
desirable.
A low level must be input to the PWMIN pin (or it must be connected to ground) if the TOC pin voltage control
system is used.
• PWMIN pulse input
A 15 to 25kHz frequency pulse signal can be input to the PWMIN pin and the low side output transistor duty can
be controlled based on the duty of that input signal. When the PWMIN pin is low, the output will be on, and when
high, the output will be off. When the PWMIN pin is open, the input will go to the high level and the output will be
off.
If PWMIN pin control is used, the EI- pin must be connected to ground and the EI+ pin must be connected to the
TOC pin.
No.A0606-10/12
LB11693JH
12. Undervoltage Protection Circuit
The undervoltage protection circuit turns off the low side output transistor
if the LVS pin voltage falls below the circuit's operating voltage (about 3.8V).
This operating voltage is the detection level for a 5V system. The detection
level can be increased by connecting a zener diode in series with the LVS pin
to apply a level shift to the detection level. The current flowing into the LVS
pin during detection is about 65µA.
To the detected
power supply
To the LVS pin
To suppress variations in the zener voltage, it is necessary to stabilize the rise of the
zener diode voltage by increasing the current that flows in the zener diode. If this is
necessary, insert a resistor between the LVS pin and ground.
When the LVS pin is open, it will be pulled to the ground level by the built-in pull-down resistor and the output will
be turned off. Thus if the undervoltage protection circuit is not used, a voltage in excess of the release voltage (about
4.3V) must be applied to the LVS pin. Note that the maximum rating for the LVS pin voltage is 30V.
13. Motor Constraint Protection Circuit
When motor motion is constrained, the external capacitor connected to the CSD pin will be alternately charged (up to
about 3.0V) with a constant current of about 2.4µA and discharged with a constant current of about 0.17µA (to about
1.0V). Thus the CSD pin voltage will have a sawtooth waveform. The motor constraint protection circuit turns the
motor (the low side output transistor) on or off repeatedly based on this sawtooth waveform. Motor drive will be on
during the period the CSD pin external capacitor is being charged from about 1.0V to about 3.0V and will be off
when it is being discharged from about 3.0V to about 1.0V. The drive on/off operation protects the IC and the motor
when the motor is physically constrained from moving. If a 0.47µF capacitor is connected to the CSD pin, the IC will
iterate an on/off cycle in which drive is on for about 0.4 seconds and off for about 5.5 seconds.
While the motor is turning, the CSD pin voltage will be held at a certain voltage (that depends on the motor speed) by
(a) a CSD pin external capacitor discharge operation based on about 10µs discharge pulses generated internally in the
IC when the Hall input IN1 switches (that is, on rising and falling edges on the FG output) and (b) a charge operation
on that capacitor by a constant current of about 2.4µA.
Since the Hall input IN1 does not switch when the motor is physically constrained, the discharge pulses are not
generated and the CSD pin external capacitor will be charged to about 3.0V by the constant current of about 2.4µA.
The motor constraint protection circuit operates when the capacitor reaches about 3.0V. The constraint protection
operation will be released when the motor constraint is released.
If the motor speed is extremely low, the CSD pin voltage during that motor rotation will be held at a comparatively
high voltage, and if that voltage reaches about 3.0V, the constraint protection function will operate. Since the
constraint protection function will operate if the Hall input IN1 frequency falls below about 10Hz, caution is required
when using the motor constraint protection circuit with motors that will operate at low speeds.
Connect the CSD pin to ground if the motor constraint protection circuit is not used.
No.A0606-11/12
LB11693JH
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of September, 2010. Specifications and information herein are subject
to change without notice.
No.A0606-12/12
PS
相关型号：
©2020 ICPDF网 联系我们和版权申明