SLP-3130C-81 [SANYO]
┆5mm yelloe-green contact type LED lamp; ø5mm yelloe绿色接触式LED灯
| 型号： | SLP-3130C-81 |
| 厂家： | 
SANYO SEMICON DEVICE |
| 描述： | ┆5mm yelloe-green contact type LED lamp |
| 文件： | 总4页 (文件大小：27K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Ordering number : EN6053
Infrared LED
SLP-3130C-81
ø5mm yelloe-green contact type LED lamp
Features
Note : Material -- lron
Coating -- Solder
Lead center off : ± 0.4
Unit : mm
• GaP yellow green LED
• 5.0mmø, round top type lamp
• Clear green resin package type
• The insertion which made it stick to PCB is possible
• High luminous intensity, high reliability and long life
• Application : for the general public welfare
5.4
ø5
ø5.8
Absolute Maximum Ratings at Ta=25°C (as per JIS C 7032)
Parameter
Symbol
Rating
Unit
mA
mA
V
1
*
0.5
0.4
Forward Current
I
25
100
F
2
*
0.4
Pulse Forward Current
Reverse Voltage
I
FP
V
3
R
D
Power Dissipation
P
70
mW
°C
Operating Temperature
Storage Temperature
Soldering Temperature
Topr
Tstg
Tsol
--25 to +80
--30 to +85
260
Anode
°C
Cathode
3
*
°C
1
*
2
*
3
*
See forward current derating
Pulse width = Max. 10ms Duty ratio = Max. 1 / 10
Max. 5sec., Lead soldering condition : Min. 1.6mm from case (used 1.6mm’t PCB)
2.5
Electrical / Optical Characteristics at Ta=25°C
Parameter
Foward Voltage
Symbol
Conditions
I = 20mA
Min.
Typ.
2.1
--
Max.
Unit
V
F
1.7
--
2.8
10
--
V
µA
mcd
nm
nm
pF
F
Reverse Current
Luminous Intensity
Peak Wave length
Line Half Width
Capacitance
I
V = 3V
R
R
4
*
I
I = 20mA
F
40
--
110
567
25
V
λ
I = 20mA
F
--
P
∆λ
I = 20mA
--
--
F
•
C
O
V = 0 F = 1MHz
--
50
--
O
Response Time
t
--
--
250
--
ns
4
*
Luminous Intensity is measured by J-16 (SONY TEKTRONIX) of which our office possess.
SANYO Electric Co.,Ltd. Sem iconductor Com pany
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
(
)
52699 GI, MI No.6053 1/4
SLP-3130C-81
Typical Characteristics
CAUTION
These shows the electrical and optical characteristics of this products, and not assure this dispersive contents.
Forward Current vs. Forward Voltage
Intensity vs. Temperature (I : constant)
F
30
20
1.5
1.0
10
5
3
2
0.5
1
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
--40 --20
0
20
40
60
80
100
Temperature (°C)
Forward Voltage (V)
Intensity vs. Current
Spectrum
10
1.0
5
2
1
0.5
0.5
0.2
0.1
0
450
1
2
5
10
20
50 100 200
500
550
600
650
Forward Current (mA)
Wave Length (nm)
Forward Current Derating (Abusolute Maximum Rating)
Directivity
0°
10°
10°
35
20°
20°
1.0
30°
30°
30
40°
40°
25
20
15
10
5
50°
60°
50°
0.5
0.1
60°
70°
70°
80°
90°
80°
90°
0
10 20 30 40 50 60 70 80 90 100
Temperature (°C)
No.6053 2/4
SLP-3130C-81
PRECAUTIONS
(1) Bending a lead should avoid not to cause chip deterioration or so. When bending is necessary, care must be taken
considering the following points :
q Bending a lead must be done before soldering.
w Bending a lead must be done in the states of fixing a lead tight and applying no stress on the resin part; otherwise it
may cause troubles such as gold wire breaking.
e A lead must be bent at intervals of 1.6mm from the edge of the resin part.
r Do not bend the same portion of lead more than twice.
(2) Setting a product by a tool such as holder should avoid. When necessary, no stress should be applied to the resin part and
lead by sufficient considerations on dimension tolerance, thermal expansion, thermal contraction of holder, product and
circuit board.
(3) The hole pitch of a circuit board must fit to its lead pitch.
(4) When soldering, care must be taken considering the following points :
q Do not heat a product under any stress (ex. : twist) to leads.
w Do not heat (by soldering, for example) a product in the states of being forced to the resin part.
(5) Do not use the flux containing chlorine which may cause corrosion of lead and washing is preferable. When washing is
necessary, avoid washing the whole product and wash only the needed part under the following conditions.
• Chemicals : Methyl alcohol
• Temperature : 45°C max.
• Time : 30sec. max.
No.6053 3/4
SLP-3130C-81
CAUTION
1. No products described or contained herein are intended for use in surgical implants, life-support systems,
aerospace equipment, nuclear power control systems, vehicles, disaster / crime-prevention equipment or
the like, and the failure of which may directly or indirectly cause injury, death or property loss.
2. Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1) Accept full responsibility and indemnify and defend SANYO ELECTRIC CO.,LTD., it’s affiliates,
subsidiaries and distributors or any of their officers and employees, jointly and severally, against any
and all claims and litigation and all damages, costs and expenses associated with such use.
2) Not impose any responsibility for any fault or negligence which may be cited in any such claim or
litigation on SANYO ELECTRIC CO., LTD., it’s affiliates, subsidiaries and distributors or any of
their officers and employees jointly or severally.
3. Information (including circuit diagrams and circuit parameters) disclosed herein is for example only; it is not
guaranteed for mass production, SANYO believes the information disclosed herein is accurate and reliable,
but no guarantees are made or implied regarding it’s use or any infringements of intellectual property rights
or other rights of third parties.
Precautionary instructions in handling gallium arsenic products
Special precautions must be taken in handling this product because it contains, gallium arsenic, which is
designated as a toxic substance by law. Be sure to adhere strictly to all applicable laws and regulations
enacted for this substance, particularly when it comes to disposal.
Manufactured by ; Tottori SANYO Electric Co., Ltd.
LED Division
5-318, Tachikawa-cho, Tottori City, 680-8634 Japan
TEL: +81-857-21-2137 FAX: +81-857-21-2161
No.6053 4/4
PS
相关型号：
©2020 ICPDF网 联系我们和版权申明