SS1331ESOT [SECELECTRONICS]
Unipolar Hall Switch-Low Sensitivity;型号: | SS1331ESOT |
厂家: | SEC Electronics Inc. |
描述: | Unipolar Hall Switch-Low Sensitivity |
文件: | 总7页 (文件大小:309K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SS1331
Unipolar Hall Switch-Low Sensitivity
Features and Benefits
Application Examples
–
–
–
–
–
–
–
–
–
3.5V to 24V Operation
-40°C to 150°C Superior temperature operation
CMOS technology
Low current consumption
Chopper-stabilized amplifier stage
Open drain output
Low sensitivity
Small Size SOT23 3L or SIP 3L
Both RoHS compliant packages
–
–
–
–
–
–
–
Automotive, Consumer and Industrial
Solid-state switch
Brushless DC motor commutation
Speed detection
Angular position detection
Proximity detection
Current detector
3 pin SOT23 (suffix SO)
3 pin SIP (suffix UA)
Functional Block Diagram
VDD
Voltage
Regulator
OUT
Chopper
Hall
Plate
GND
SIP Package
Pin 1 – VDD
Pin 2 – GND
Pin 3 – OUT
SOT Package
Pin 1 – VDD
Pin 2 – OUT
Pin 3 – GND
1
V3.10 Nov 1, 2013
SS1331
Unipolar Hall Switch-Low Sensitivity
General Description
The SS1331 is a unipolar Hall-effect sensor IC fab-
ricated from CMOS technology. The device inte-
grates a voltage regulator, Hall sensor with dy-
namic offset cancellation system, small signal am-
plifier, Schmitt trigger and an open-drain output
driver. With suitable output pull up, they can be
used with bipolar or CMOS logic circuits.
both temperature and supply voltage changes. The
unipolar switching characteristic makes these de-
vices ideal for use with a simple bar or rod magnet.
Thanks to its wide operating voltage range and ex-
tended choice of temperature range, it is quite suit-
able for use in automotive, industrial and consumer
applications.
These Hall-effect switches are monolithic integrat-
ed circuits with tighter magnetic specifications, de-
signed to operate continuously over extended tem-
peratures to +150°C,and are more stable with
The device is delivered in a Small Outline Tran-
sistor (SOT) or in a Plastic Single In Line (SIP 3L
flat). Both 3-lead packages are RoHS compliat.
Glossary of Terms
MilliTesla (mT), Gauss Units of magnetic flux density: 1mT = 10 Gauss
RoHS
Restriction of Hazardous Substances
Operating Point (BOP)
Magnetic flux density applied on the branded side of the package which turns the
output driver ON (VOUT = VDSon
)
Release Point (BRP)
Magnetic flux density applied on the branded side of the package which turns the
output driver OFF (VOUT = high)
2
V3.10 Nov 1, 2013
SS1331
Unipolar Hall Switch-Low Sensitivity
Pin Definitions and Description
SOT Pin № SIP Pin №
Name
VDD
Type
Supply
Output
Ground
Function
Supply Voltage pin
Open Drain Output pin
Ground pin
1
2
3
1
3
2
OUT
GND
Absolute Maximum Ratings
Symbol
VDD
IDD
Parameter
Value
Units
V
Supply Voltage
Supply Current
28
50
28
50
mA
V
VOUT
IOUT
TS
Output Voltage
Output Current
mA
Storage Temperature Range
-65 to 170
°C
Symbol
TA
Operating Temperature Range
Temperature Suffix “E”
Temperature Suffix “K”
Temperature Suffix “L”
Value
Units
°C
-40 to 85
-40 to 125
-40 to 150
TA
°C
TA
°C
Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximum- rated conditions for ex-
tended periods may affect device reliability.
3
V3.10 Nov 1, 2013
SS1331
Unipolar Hall Switch-Low Sensitivity
General Electrical Specifications
DC Operating Parameters TA = 25°C, VDD= 3.5V to 24V (unless otherwise specified)
Typ
Parameter
Symbol
VDD
Test Conditions
Operating
Min
3.5
Max
24
Units
V
Supply Voltage
1.5
2.5
0.4
IDD
Supply Current
B < BRP
5
mA
V
VDSon
IOFF
IOUT = 20mA, B >
Output Saturation Voltage
Output Leakage Current
Output Rise Time
Output Fall Time
0.5
10
BOP
B <
VOUT = 24V
BRP
0.01
0.25
0.25
µA
µs
t
r
RL = 1kΩ, CL = 20pF
RL = 1kΩ, CL = 20pF
t
f
µs
Magnetic Specifications
DC Operating Parameters VDD = 3.5V to 24V (unless otherwise specified)
Package
Parameter
Symbol
BOP
Test Conditions
Min
45
Ta=25°C,Vdd=12V DC 10
Typ
Max
Units
G
Operating Point
Release Point
Hysteresis
80
110
95
UA
BRP
50
G
BHYST
BOP
30
G
Operating Point
Release Point
Hysteresis
-110
Ta=25°C,Vdd=12V DC -95
-80
-50
30
-45
-10
G
SO
BRP
G
BHYST
G
Output Behavior versus Magnetic Pole
DC Operating Parameters TA = -40°C to 150°C, VDD = 3.5V to 24V (unless otherwise specified)
Test Conditions (UA) Test Conditions (SO)
OUT
High
Low
B < BRP
B > BOP
B > BRP
B < BOP
The SOT-23 device is reversed from the UA package. The SOT-23 output transistor will be turned on(drops low) in the presence of a
sufficiently strong North pole magnetic field applied to the marked face.
4
V3.10 Nov 1, 2013
SS1331
Unipolar Hall Switch-Low Sensitivity
Application Information
For proper operation, a 100nF bypass capacitor should be placed as close as possible to the device between the
DD and ground pin.
V
For reverse voltage protection, it is recommended to connect a resistor or a diode in series with the VDD pin.
When using a resistor, three points are important:
- the resistor has to limit the reverse current to 50mA maximum (VCC / R1(≈50mA)
- the resulting device supply voltage VDD has to be higher than VDD min (VDD = VCC – R1∙IDD
)
- the resistor has to withstand the power dissipated in reverse voltage condition (PD = VCC2/ R1)
When using a diode, a reverse current cannot flow and the voltage drop is almost constant (≈0.7V).
Therefore, a 100Ω/0.25W resistor for 5V application and a diode for higher supply voltage are recommended.
Typical Three-Wire Application Circuit
When a weak power supply is used or when the device is intended to be used in noisy environment, it is recom-
mended that figure followed is used.
The low-pass filter formed by R1 and C1 and the Zener diode Z1 bypass the disturbances or voltage spikes occur-
ring on the device supply voltage VDD. The diode D1 provides additional reverse voltage protection.
Both solutions provide the required reverse voltage protection.
Automotive and Harsh, Noisy Environments Three-Wire Circuit
ESD Precautions
Electronic semiconductor products are sensitive to Electro Static Discharge (ESD).
Always observe Electro Static Discharge control procedures whenever handling semiconductor products.
5
V3.10 Nov 1, 2013
SS1331
Unipolar Hall Switch-Low Sensitivity
Package Information
Package UA, 3-Pin SIP:
2.13
1.87
3° ± 1°
1.00
45° ± 1°
4.0 ± 0.01
2
1
Sensor Location
0.84(Nom)
6° ± 1°
Active Area Depth:
3° ± 1°
0.44± 0.01
1
2
3
6° ± 1°
3° ± 1°
0.05 ± 0.05
0.39± 0.01
0.38 ± 0.01
Notes:
1). Controlling dimension : mm ;
2). Leads must be free of flash and plating voids ;
3). Do not bend leads within 1 mm of lead to package
interface ;
4). PINOUT: Pin 1 VDD
Pin 2 GND
Pin 3 Output
1.27
2.54
6
V3.10 Nov 1, 2013
SS1331
Unipolar Hall Switch-Low Sensitivity
Package SO, 3-Pin SOT-23:
Notes
1). PINOUT: Pin 1 VDD
Pin 2 Output
Top
3
Pin 3 GND
2). All dimensions are in millimeters;
2.60
3.00
1.50
1.80
1
2
1.70
2.10
Side Vie
End
2.70
3.10
0.10
0.25
1.00
1.30
0.70
0.90
0.20
Min
0.00
0.10
0.35
0.50
Ordering Information
Part No.
Pb-free
YES
YES
YES
YES
YES
YES
Temperature Code
-40°C to 85°C
Package Code
SOT-23
TO-92
Packing
SS1331ESOT
SS1331EUA
SS1331KSOT
SS1331KUA
SS1331LSOT
SS1331LUA
7-in. reel, 3000 pieces/ reel
Bulk, 1000 pieces/ bag
7-in. reel, 3000 pieces/ reel
Bulk, 1000 pieces/ bag
7-in. reel, 3000 pieces/ reel
Bulk, 1000 pieces/ bag
-40°C to 85°C
-40°C to 125°C
-40°C to 125°C
-40°C to 150°C
-40°C to 150°C
SOT-23
TO-92
SOT-23
TO-92
7
V3.10 Nov 1, 2013
相关型号:
©2020 ICPDF网 联系我们和版权申明