X1G004251006701 [SEIKO]
LVPECL Output Clock Oscillator,;型号: | X1G004251006701 |
厂家: | SEIKO EPSON CORPORATION |
描述: | LVPECL Output Clock Oscillator, |
文件: | 总7页 (文件大小:494K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Clock OSC
SG3225EAN
SG3225EAN 74.250000 MHz KCBA
Product name
X1G0042510067xx
Product Number / Ordering code
Please refer to the 9.Packing information about xx (last 2 digits)
Output waveform
Pb free / Complies with EU RoHS directive
LV-PECL
Reference weight Typ. 25 mg
1.Absolute maximum ratings
Parameter
Symbol
Vcc-GND
T_stg
Min.
-0.3
-40
Typ.
Max.
+4
+125
Unit
V
ºC
V
Conditions / Remarks
-
Storage as single product
ST or OE Terminal
Maximum supply voltage
Storage temperature
Input voltage
-
-
-
Vin
-0.3
Vcc+0.3
2.Specifications(characteristics)
Parameter
Output frequency
Symbol
Min.
Typ.
74.2500
Max.
Unit
MHz
V
Conditions / Remarks
f0
Vcc
T_use
f_tol
Icc
-
Supply voltage
2.25
-
3.63
-
Operating temperature
Frequency tolerance
Current consumption
Stand-by current
Disable current
-20
-
+70
ºC
x10-6
mA
mA
mA
%
-
-20
-
20
OE = Vcc , L_ECL = 50 ohm
-
-
-
65
I_std
I_dis
SYM
VOH
VOL
L_ECL
VIH
-
-
-
OE=GND
-
-
20.0
At output crossing point
-
Symmetry
45
-
55
Output voltage(LV-PECL)
Vcc-1.0
-
-
-
V
-
-
Vcc-1.62
V
Terminated to Vcc - 2.0V
OE Terminal
Output load condition(ECL)
Input voltage
-
50
-
Ω
70% Vcc
-
-
VIL
OE Terminal
-
-
-
30% Vcc
At 20% to 80% output swing
At 20% to 80% output swing
-
Rise time
Fall time
Start-up time
Jitter
tr
-
0.35
ps
ps
tf
-
-
0.35
t_str
tDJ
-
-
3
-
-
-
-
-
-
-
-
-
-
-
-
-
5
ms
Deterministic Jitter Vcc=2.5V
Random Jitter Vcc=2.5V
δ(RMS of total distribution) Vcc=2.5V
Peak to Peak Vcc=2.5V
-
-
TBD
TBD
TBD
TBD
-
ps
TRJ
-
ps
tRMS
tp-p
-
ps
-
ps
tacc
-
ps
Off set Frequency: 12kHz to 20MHz Vcc=2.5V
-
Phase jitter
tPJ
-
TBD
-
ps
Phase noise
L(f)
-
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
x10-6/Year
Off set 10Hz Vcc=2.5V
Off set 100Hz Vcc=2.5V
Off set 1kHz Vcc=2.5V
Off set 10kHz Vcc=2.5V
Off set 100kHz Vcc=2.5V
Off set 1MHz Vcc=2.5V
@+25ºC first year
-
TBD
TBD
TBD
TBD
TBD
TBD
-
-
-
-
-
-
Frequency aging
f_age
-5
1 Page
3.Test circuit
1) To observe waveform and current (case 1)
Vcc
A
+3.3 V
Vcc
________
130 Ω
82 Ω
130 Ω
OUT
OUT
GND
By-pass
capacitor 2
Test Point
Test Point
82 Ω
NC
OE
OE pin
Power
supply 2
By-pass
capacitor 1
________
* The lines from OUT and OUT pin are same length.
* To measure the disable current, OE pin is connected to GND
2) To observe waveform and current (case 2)
A
Test Point
Test Point
+3.3 V
Vcc
________
OUT
OUT
GND
By-pass
capacitor 2
50 Ω
50 Ω
NC
OE
OE pin
Power
supply 2
Vcc-2 V
By-pass
capacitor 1
________
* The lines from OUT and OUT pin are same length.
* To measure the disable current, OE pin is connected to GND
3) Measurement condition
A) Oscilloscope
•Bandwidth should be 5 times higher than DUT’s output frequency (4 GHz).
•Probe ground should be placed closely from test point and lead length should be as short as possible.
B) By-pass capacitor 1 (approx. 0.01 μF to 0.1 μF) places closely between Vcc and GND.
C) By-pass capacitor 2 (approx. 10 μF) places closely between power supply terminals on the board.
D) Use the current meter whose internal impedance value is small.
E) Power supply
• Start up time (0 Vg90 %Vcc) of power source should be more than 150 μs and
slew rate should be less than 19.8 mV/μs.
• Impedance of power supply should be as low as possible.
2 Page
4.Timing chart
Vcc
tr
tf
________
OUT
80 % of amplitude
20 % of amplitude
Vcc-2 V
OUT
GND
tw
SYM = tw / t
t
5.External dimensions
(Unit: mm)
6.Footprint(Recommended)
(Unit: mm)
0.82
#5
0.86
#4
#6
#1
#2
#3
2.58
To maintain stable operation, provide a 0.01uF to 0.1uF
by-pass capacitor at a location as near as possible to the
power source terminal of the crystal product (between Vcc
- GND).
7.Reflow profile
Reflow condition (Follow of JEDEC STD-020D.01)
Temperature[C]
300
TP ;+260C
+255C
tp;20sto40s
Ramp-down
250
200
150
100
50
Avg. Ramp-up
3 C/sMax.
tL
TL
;+217C
60sto150s
Tsmax;+200C
6C/sMax.
(+217Cover)
ts
Tsmin;+150C
60sto180s
(+150Cto+200C)
Time +25CtoPeak
0
60 120 180 240 300 360 420 480 540 600 660 720 780
Time[s]
3 Page
8.Example of schematic layout
This figure shows an example of this product’s application schematic.
As with any high speed analog circuitry, the power supply pins for this device are vulnerable to
noise. In order to achieve optimum jitter performance, power isolation with filter device is
required for power supply pins.
In order to achieve best performance of the power isolation filter, it is recommended that the
filter composing devices is placed on the device side of the PCB as close to the power pins as
possible. The component value of this filter is just an example, it may have to be adjusted.
4 Page
* By-pass capacitor (approx. 0.01 μF to 0.1 μF) places closely between Vcc and GND.
* By-pass capacitor (approx. 10 μF) places closely between power supply terminals on the board.
* Please design the two output lines by characteristic impedance 50 Ω and same length, and try
to make the output lines as short as possible.
* Terminators place near the input device.
9.Packing information
[ 1 ]Product number last 2 digits code(xx) description
X1G0042510067xx
The recommended code is "00"
Condition
Condition
500pcs / Reel
1000pcs / Reel
2000pcs / Reel
Code
Code
13
01
Any Q'ty vinyl bag(Tape cut)
Any Q'ty / Reel
11
14
12
250pcs / Reel
00
5 Page
[ 2 ] Taping specification
Subject to EIA-481 & IEC-60286
(1) Tape dimensions
ꢀꢀꢀMaterial of the Carrier Tape : PS
ꢀꢀꢀMaterial of the Top Tape : PET+PE
Unit: mm
10 P: 400.1
4.00.1
2.00.1
1.40.1
+0.1
-0
φ1.55
0.250.05
4.00.1
2.80.1
φ1.00.1
Direction of unreeling
(2) Reel dimensions
Center material
: PS
Material of the Reel : PS
11.41.0
9.00.3
+0.3
-0
2.0
6 Page
10.Notice
This material is subject to change without notice.
Any part of this material may not be reproduced or duplicated in any form or any means without the written permission
of Seiko Epson.
The information about applied circuitry, software, usage, etc. written in this material is intended for reference only.
Seiko Epson does not assume any liability for the occurrence of infringing on any patent or copyright of a third party.
This material does not authorize the licensing for any patent or intellectual copyrights.
When exporting the products or technology described in this material, you should comply with the applicable
export control laws and regulations and follow the procedures required by such laws and regulations.
You are requested not to use the products (and any technical information furnished, if any) for the development
and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that you
would not make the products available to any third party who may use the products for such prohibited purposes.
These products are intended for general use in electronic equipment. When using them in specific applications that require
extremely high reliability, such as the applications stated below, you must obtain permission from Seiko Epson in advance.
/ Space equipment (artificial satellites, rockets, etc.)
/ Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc.)
/ Medical instruments to sustain life
/ Submarine transmitters
/ Power stations and related
/ Fire work equipment and security equipment
/ Traffic control equipment
/ And others requiring equivalent reliability.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective.
11.Contact us
http://www5.epsondevice.com/en/contact/
7 Page
相关型号:
©2020 ICPDF网 联系我们和版权申明