X1M000221001000 [SEIKO]
LVDS Output Clock Oscillator,;型号: | X1M000221001000 |
厂家: | SEIKO EPSON CORPORATION |
描述: | LVDS Output Clock Oscillator, 机械 输出元件 振荡器 |
文件: | 总7页 (文件大小:456K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Clock OSC
EG-2102CB
EG-2102CB 200.000000MHz +/-50ppm LGSN
Product name
X1M0002210010xx
Product Number / Ordering code
Please refer to the 9.Packing information about xx (last 2 digits)
Output waveform
LVDS
Pb free / Complies with EU RoHS directive
Reference weight Typ. 71 mg
1.Absolute maximum ratings
Parameter
Symbol
Vcc-GND
T_stg
Min.
-0.5
-40
Typ.
Max.
4
125
Unit
V
ºC
V
Conditions / Remarks
-
Storage as single product
ST or OE Terminal
Maximum supply voltage
Storage temperature
Input voltage
-
-
-
Vin
-0.5
Vcc+0.5
2.Specifications(characteristics)
Parameter
Output frequency
Symbol
Min.
-
Typ.
200.0000
Max.
-
Unit
MHz
V
Conditions / Remarks
-
f0
Vcc
T_use
f_tol
Icc
-
Supply voltage
-0.5
-
4
Storage as single product
Operating temperature
Frequency tolerance
Current consumption
Stand-by current
Disable current
-40
-
125
50
30
-
ºC
x10-6
mA
mA
mA
%
-
-50
-
-
-
-
-
I_std
I_dis
SYM
VOD
dVOD
Vos
dVos
L_LVDS
VIH
-
-
-
-
-
15.0
55
454
50
1.375
150
-
-
Symmetry
45
-
-
Output voltage(LVDS)
247
-
mV
mV
V
-
-
-
-
1.125
-
-
-
-
mV
Ω
-
Output load condition(LVDS)
Input voltage
-
100
-
0.7Vcc
-
-
VIL
-
-
-
-
0.3Vcc
0.4
0.4
10
N/A
N/A
N/A
N/A
N/A
0.23
-
-
Rise time
Fall time
Start-up time
Jitter
tr
-
ps
ps
-
tf
-
-
-
t_str
tDJ
-
-
ms
Deterministic Jitter
Random Jitter
-
-
ps
TRJ
-
-
ps
tRMS
tp-p
δ(RMS of total distribution)
Peak to Peak
-
-
ps
-
-
ps
Accumulated Jitter(δ) n=2 to 50000 cycles
Off set Frequency: 12kHz to 20MHz
Off set 1Hz
tacc
-
-
-
ps
Phase jitter
tPJ
-
ps
Phase noise
L(f)
-
-
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
x10-6/Year
Off set 10Hz
-
-54.8
-82.0
-110.8
-139.2
-148.8
-151.0
-
-
Off set 100Hz
-
-
Off set 1kHz
-
-
Off set 10kHz
-
-
Off set 100kHz
Off set 1MHz
-
-
-
-
@+25ºC first year
Frequency aging
f_age
-10
-
10
-
-
-
1 Page
3.Test circuit
1) To observe waveform and current (case 1)
A
+3.3 V
Vcc
OUT
NC
OUT
GND
By-pass
capacitor 2
Differentila probe
Oscillo-
scope
100 Ω
OE
Power
supply 1
OE pin*
By-pass
capacitor 1
* The lines from OUT and OUT pin are same length.
* To measure the disable current, OE pin is connected to GND
2) To observe waveform and current (case 2)
VOD
+3.3 V
Vcc
V
OUT
NC
OUT
GND
By-pass
capacitor 2
50 Ω
50 Ω
VOS
V
OE
OE pin
Power
supply 1
By-pass
capacitor 1
* The lines from OUT and OUT pin are same length.
3) Measurement condition
A) Oscilloscope
•Bandwidth should be 5 times higher than DUT’s output frequency (4 GHz).
•Probe ground should be placed closely from test point and lead length should be as short as possible.
B) By-pass capacitor 1 (approx. 0.01 μF to 0.1 μF) places closely between Vcc and GND.
C) By-pass capacitor 2 (approx. 10 μF) places closely between power supply terminals on the board.
D) Use the current meter whose internal impedance value is small.
E) Power supply
• Start up time (0 Vg90 %Vcc) of power source should be more than 150 μs and
slew rate should be less than 19.8 mV/μs.
• Impedance of power supply should be as low as possible.
2 Page
4.Timing chart
Each output waveform (OUT, and OUT)
Vcc
OUT
OUT
50 % of OUT
amplitude
50 % of OUT
amplitude
VOS1
VOS2
GND
tw
SYM = tw / t
t
dVOS =|VOS1-VOS2
|
Differential output waveform (OUT – OUT)
tr
tf
OUT
80 % of amplitude
VOD1
Differential 0 V
VOD2
20 % of amplitude
OUT
dVOD =|VOD1-VOD2
|
5.External dimensions
(Unit: mm)
6.Footprint(Recommended)
(Unit: mm)
0.84
0.64
#6 #5 #4
#4
#5
#6
E 212.50P
1P 1X1A
Pin map
Pin
Connection
#3
#1
#2
1.27
#1
#2 #3
1
OE
2
5.0±0.2
1.27
2.54
2.54
To maintain stable operation, provide a 0.01uF to 0.1uF
by-pass capacitor at a location as near as possible to the
power source terminal of the crystal product (between Vcc
- GND).
3 Page
7.Reflow profile
Reflow condition (Follow of JEDEC STD-020D.01)
Temperature[C]
300
TP ;+260C
+255C
tp;20sto40s
250
200
150
100
50
Avg. Ramp-up
3 C/sMax.
tL
TL
;+217C
Ramp-down
6C/sMax.
60sto150s
(+217Cover)
Tsmax;+200C
ts
Tsmin;+150C
60sto180s
(+150Cto+200C)
Time +25CtoPeak
0
60 120 180 240 300 360 420 480 540 600 660 720 780
Time[s]
8.PCB layout (2 layers, 2nd layer is all GND pattern)
4 Page
* By-pass capacitor (approx. 0.01 μF to 0.1 μF) places closely between Vcc and GND.
* By-pass capacitor (approx. 10 μF) places closely between power supply terminals on the board.
* Please design the two output lines by characteristic impedance 100 Ω and same length,
and try to make the output lines as short as possible.
9.Packing information
[ 1 ]Product number last 2 digits code(xx) description
X1M0002210010xx
The recommended code is "00"
Condition
Condition
500pcs / Reel
1000pcs / Reel
Code
Code
13
01
Any Q'ty vinyl bag(Tape cut)
Any Q'ty / Reel
11
00
12
250pcs / Reel
5 Page
[ 2 ] Taping specification
Subject to EIA-481 & IEC-60286
(1) Tape dimensions
ꢀꢀꢀMaterial of the Carrier Tape : PS
ꢀꢀꢀMaterial of the Top Tape : PET+PE
Unit: mm
A
B
Carrier tape
Top tape
G
C
F
Symbol
Value
A
φ1.5
B
C
D
E
F
G
H
4.0±0.1 8.0±0.1 7.25±0.2 12.0±0.2 1.40±0.1 3.5±0.1 5.4±0.1
+0.1/-0
(2) Reel dimensions
Center material
: PS
Material of the Reel : PS
Unit: mm
13.0±1.0
6 Page
10.Notice
This material is subject to change without notice.
Any part of this material may not be reproduced or duplicated in any form or any means without the written permission
of Seiko Epson.
The information about applied circuitry, software, usage, etc. written in this material is intended for reference only.
Seiko Epson does not assume any liability for the occurrence of infringing on any patent or copyright of a third party.
This material does not authorize the licensing for any patent or intellectual copyrights.
When exporting the products or technology described in this material, you should comply with the applicable
export control laws and regulations and follow the procedures required by such laws and regulations.
You are requested not to use the products (and any technical information furnished, if any) for the development
and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that you
would not make the products available to any third party who may use the products for such prohibited purposes.
These products are intended for general use in electronic equipment. When using them in specific applications that require
extremely high reliability, such as the applications stated below, you must obtain permission from Seiko Epson in advance.
/ Space equipment (artificial satellites, rockets, etc.)
/ Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc.)
/ Medical instruments to sustain life
/ Submarine transmitters
/ Power stations and related
/ Fire work equipment and security equipment
/ Traffic control equipment
/ And others requiring equivalent reliability.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective.
11.Contact us
http://www5.epsondevice.com/en/contact/
7 Page
相关型号:
©2020 ICPDF网 联系我们和版权申明