LM1084M [SEME-LAB]
5 AMP POSITIVE; 5 AMP POSITIVE型号: | LM1084M |
厂家: | SEME LAB |
描述: | 5 AMP POSITIVE |
文件: | 总5页 (文件大小:67K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM1084M
MILITARY VERSION
5 AMP POSITIVE
VOLTAGE REGULATOR
FEATURES
• Low Dropout Performance
INPUT
• Fixed or Adjustable Voltages
SAFE AREA
PROTECTION
• Fixed Output Voltages of 3.3V, 5V & 12V
• Adjustable Output Voltage Range From 1.2V
• Line Regulation 0.015% / V Typical.
• Load Regulation 0.01% Typical.
LIMIT
CURRENT
LIMITING
AMPLIFIER
OUTPUT
SENSE
• Available in Hermetically Sealed TO–3, SMD1 and
TO–257 (isolated & non-isolated) Packages.
T HERM AL
OVERLO AD
• Military Temperature Range (–55 to +150°C)
VOLTAGE
REGULATION
AMPLIFIER
(1)
DEVICE
PACKAGE
VRE F
ADJUST
LM1084MK–XX
LM1084MG–XX
LM1084MIG–XX
LM1084MSM–XX
TO–3
TO–257
Isolated TO–257
SMD1
DESCRIPTION
The LT1084 voltage regulators are monolithic
integrated circuits designed for use in applications
requiring a well regulated positive output voltage
with low input-output differential voltage.
Note
1) –XX = Voltage Option: 3.3, 5 or 12
–XX = Left blank for Adjustable Option.
Features include full power usage of up to 5A load current, internal current limiting and thermal shutdown. Safe area
protection on the die is also included, providing protection of the series pass Darlington transistor under most conditions.
The hermetically sealed TO–3 packages are utilised for high reliablitiy and low thermal resistance, whilst the SMD1
package is designed for surface mount applications.
ABSOLUTE MAXIMUM RATINGS (T
= 25°C unless otherwise stated)
case
V
Input – Output Voltage Differential
35V
IN
D
P
Power Dissipation
Internally limited *
R
R
R
Thermal Resistance Junction To Case
TO–3
TO–3
Control
Power
0.76°C / W
2.3°C / W
θJC
θJC
θJC
Thermal Resistance Junction To Case
Thermal Resistance Junction To Case
SMD1
SMD1
Control
Power
0.79°C / W
4.0°C / W
TO–257
TO–257
Control
Power
0.79°C / W
4.0°C / W
T
Operating Junction Temperature Range
Control
Power
–55 to 150°C
–55 to 200°C
J
T
T
Storage Temperature Range
Lead Temperature (for 10 sec.)
–65 to 150°C
300°C
STG
LEAD
* These ratings are only applicable for power dissipations of 30 Watts over a limited range of VIN – VOUT
.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is
believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in
its use. Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
Document Number 6386
Issue 1
E-mail: sales@semelab.co.uk
Website: http://www.semelab.co.uk
LM1084M
MILITARY VERSION
LM1084MK & LM1084MSM
ELECTRICAL CHARACTERISTICS (TJ = 25°C Unless otherwise stated)
Output
Parameter
Voltage Test Conditions 1,2
Min.
Typ.
Max.
Unit
VIN – VOUT = 6.3V
3.3
IO = 10mA
3.267
3.3
3.333
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
3.234
4.95
3.3
5
3.366
5.05
VIN – VOUT = 8V
4
VO
Output Voltage
5
V
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
4.90
5
5.10
VIN – VOUT = 15V
12
11.88
11.76
1.238
1.225
12
12.12
12.24
1.262
1.270
0.2
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
12
VIN – VOUT = VO + 3V
ADJ.
1.25
1.25
0.015
0.035
4
VREF
Reference Voltage
Line Regulation
V
%
%
IO = 10mA to 5A
TJ = Over Temp 3
TJ = 25°C
VIN – VOUT = 1.5 to 15V
IO = 10mA
TJ = Over Temp 3
IO = 10mA
4
REG(LINE)
VIN – VOUT = 1.5 to 35V
TJ = Over Temp 3
VIN – VOUT = 3V
VIN – VOUT = 3V
ΔVOUT , ΔVREF = 1%
VIN – VOUT = 5V
VIN – VOUT = 25V
VIN – VOUT = 35V
tp = 30ms
0.05
0.5
TJ = 25°C
0.1
0.2
1.3
6.5
0.3
0.4
1.5
4
REG(LOAD) Load Regulation
%
V
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = 25°C
VD
ICL
IQ
Dropout Voltage
Current Limit
5.5
0.3
A
0.6
10
Quiescent Current
mA
REG(THERM) Thermal Regulation
0.002
55
0.01
% / W
TJ = 25°C
IPIN
ΔIPIN
TS
Adjust Pin Current
μA
μA
%
TJ = Over Temp 3
120
5
Adjust Pin Current Change
Temperature Stability
TJ = Over Temp 3
VIN – VOUT = 5V
TJ = Over Temp 3
VIN – VOUT = 25V
TJ = Over Temp 3
TJ = 25°C
0.2
0.5
IO = 0.5A
IO = 0.5A
IO
Minimum Load Current
RMS Output Noise 5
Ripple Rejection Ratio 6
5
10
mA
%VO
dB
VN
RA
0.003
75
VIN – VOUT = 3V
TJ = Over Temp 3
IO = 3A
60
1. Test Conditions unless otherwise stated: VIN = 1.5 to 35V, or Maximum Input, whichever is less.
IO = 10mA to 5A.
2. These specifications are only applicable for power dissipations of 45 Watts over a limited range of VIN – VOUT
.
3. Over Temp. = Over specified Junction Temperature Range (See Absolute Maximum Ratings).
4. Low duty cycle pulse test with Kelvin connections required. Changes in output voltage are covered under the specification
for thermal regulation.
5. Bandwidth of 10Hz to 10kHz.
6. 120Hz input ripple, 15V = 64dB min. COUT (CADJ) = 25μF.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is
believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in
its use. Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
Document Number 6386
Issue 1
E-mail: sales@semelab.co.uk
Website: http://www.semelab.co.uk
LM1084M
MILITARY VERSION
LM1084MG
ELECTRICAL CHARACTERISTICS (TJ = 25°C Unless otherwise stated)
Output
Parameter
Voltage Test Conditions 1,2
Min.
Typ.
Max.
Unit
VIN – VOUT = 6.3V
3.3
IO = 10mA
3.267
3.3
3.333
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
3.234
4.95
3.3
5
3.366
5.05
VIN – VOUT = 8V
4
VO
Output Voltage
5
V
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
4.90
5
5.10
VIN – VOUT = 15V
12
11.88
11.76
1.238
1.225
12
12.12
12.24
1.262
1.270
0.2
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
12
VIN – VOUT = VO + 3V
ADJ.
1.25
1.25
0.015
0.035
4
VREF
Reference Voltage
Line Regulation
V
%
%
IO = 10mA to 5A
TJ = Over Temp 3
TJ = 25°C
VIN – VOUT = 1.5 to 15V
IO = 10mA
TJ = Over Temp 3
IO = 10mA
4
REG(LINE)
VIN – VOUT = 1.5 to 35V
TJ = Over Temp 3
VIN – VOUT = 3V
VIN – VOUT = 3V
ΔVOUT , ΔVREF = 1%
VIN – VOUT = 5V
VIN – VOUT = 25V
VIN – VOUT = 35V
tp = 30ms
0.05
0.5
TJ = 25°C
0.4
0.7
1.3
6.5
0.5
0.6
1.5
4
REG(LOAD) Load Regulation
%
V
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = 25°C
VD
ICL
IQ
Dropout Voltage
Current Limit
5.5
0.3
A
0.6
10
Quiescent Current
mA
REG(THERM) Thermal Regulation
0.002
55
0.01
% / W
TJ = 25°C
IPIN
ΔIPIN
TS
Adjust Pin Current
μA
μA
%
TJ = Over Temp 3
120
5
Adjust Pin Current Change
Temperature Stability
TJ = Over Temp 3
VIN – VOUT = 5V
TJ = Over Temp 3
VIN – VOUT = 25V
TJ = Over Temp 3
TJ = 25°C
0.2
0.5
IO = 0.5A
IO = 0.5A
IO
Minimum Load Current
RMS Output Noise 5
Ripple Rejection Ratio 6
5
10
mA
%VO
dB
VN
RA
0.003
75
VIN – VOUT = 3V
TJ = Over Temp 3
IO = 3A
60
1. Test Conditions unless otherwise stated: VIN = 1.5 to 35V, or Maximum Input, whichever is less.
IO = 10mA to 5A.
2. These specifications are only applicable for power dissipations of 45 Watts over a limited range of VIN – VOUT
.
3. Over Temp. = Over specified Junction Temperature Range (See Absolute Maximum Ratings).
4. Low duty cycle pulse test with Kelvin connections required. Changes in output voltage are covered under the specification
for thermal regulation.
5. Bandwidth of 10Hz to 10kHz.
6. 120Hz input ripple, 15V = 64dB min. COUT (CADJ) = 25μF.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is
believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in
its use. Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
Document Number 6386
Issue 1
E-mail: sales@semelab.co.uk
Website: http://www.semelab.co.uk
LM1084M
MILITARY VERSION
ELECTRICAL CHARACTERISTICS (TJ = 25°C Unless otherwise stated)
LM1084MIG
Output
Parameter
Voltage Test Conditions 1,2
Min.
Typ.
Max.
Unit
VIN – VOUT = 6.3V
3.3
IO = 10mA
3.267
3.3
3.333
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
3.234
4.95
3.3
5
3.366
5.05
VIN – VOUT = 8V
4
VO
Output Voltage
5
V
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
4.90
5
5.10
VIN – VOUT = 15V
12
11.88
11.76
1.231
1.219
12
12.12
12.24
1.268
1.281
0.2
IO = 10mA to 5A
TJ = Over Temp 3
IO = 10mA
12
VIN – VOUT = VO + 3V
ADJ.
1.25
1.25
0.015
0.035
4
VREF
Reference Voltage
Line Regulation
V
%
%
IO = 10mA to 5A
TJ = Over Temp 3
TJ = 25°C
VIN – VOUT = 1.5 to 15V
IO = 10mA
TJ = Over Temp 3
IO = 10mA
4
REG(LINE)
VIN – VOUT = 1.5 to 35V
TJ = Over Temp 3
VIN – VOUT = 3V
VIN – VOUT = 3V
ΔVOUT , ΔVREF = 1%
VIN – VOUT = 5V
VIN – VOUT = 25V
VIN – VOUT = 35V
tp = 30ms
0.05
0.5
TJ = 25°C
0.7
0.8
1.3
6.5
1.25
1.65
1.5
4
REG(LOAD) Load Regulation
%
V
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = Over Temp 3
TJ = 25°C
VD
ICL
IQ
Dropout Voltage
Current Limit
5.5
0.3
A
0.6
10
Quiescent Current
mA
REG(THERM) Thermal Regulation
0.002
55
0.01
% / W
TJ = 25°C
IPIN
ΔIPIN
TS
Adjust Pin Current
μA
μA
%
TJ = Over Temp 3
120
5
Adjust Pin Current Change
Temperature Stability
TJ = Over Temp 3
VIN – VOUT = 5V
TJ = Over Temp 3
VIN – VOUT = 25V
TJ = Over Temp 3
TJ = 25°C
0.2
0.5
IO = 0.5A
IO = 0.5A
IO
Minimum Load Current
RMS Output Noise 5
Ripple Rejection Ratio 6
5
10
mA
%VO
dB
VN
RA
0.003
75
VIN – VOUT = 3V
TJ = Over Temp 3
IO = 3A
60
1. Test Conditions unless otherwise stated: VIN = 1.5 to 35V, or Maximum Input, whichever is less.
IO = 10mA to 5A.
2. These specifications are only applicable for power dissipations of 45 Watts over a limited range of VIN – VOUT
.
3. Over Temp. = Over specified Junction Temperature Range (See Absolute Maximum Ratings).
4. Low duty cycle pulse test with Kelvin connections required. Changes in output voltage are covered under the specification
for thermal regulation.
5. Bandwidth of 10Hz to 10kHz.
6. 120Hz input ripple, 15V = 64dB min. COUT (CADJ) = 25μF.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is
believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in
its use. Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
Document Number 6386
Issue 1
E-mail: sales@semelab.co.uk
Website: http://www.semelab.co.uk
LM1084M
MILITARY VERSION
K Package (TO–3)
G & IG Packages (TO–257)
40.01 (1.575)
Max.
10.41 (0.410)
10.72 (0.422)
4.83 (0.190)
5.46 (0.215)
0.89 (0.035)
1.14 (0.045)
26.67
(1.050)
Max.
4.47 (0.176)
Rad.
2 Pls.
3.05 (0.120)
3.30 (0.130)
Ø
1 2 3
22.23 (0.875)
Max.
11.43 (0.450)
6.35 (0.250)
12.19 (0.48)
11.18 (0.44)
1.09 (0.043)
0.97 (0.038)
Dia.
2.54 0.08
(0.10 0.003)
3.05 0.08
(0.12 0.003)
1.63 (0.064)
1.52 (0.060)
0.64 (0.025)
0.89 (0.035)
30.40 (1.197)
29.90 (1.177)
SMD1 Package
0
.
8
9
(
0
.
0
3
5
)
4.09 (0.161)
3.84 (0.151)
2 Pls
m
i
n
.
3
.
7
0
(
)
0
.
1
4
6
)
3
.
7
0
(
0
.
1
4
6
3
.
6
0
(
0
.
1
4
2
)
3
.
4
1
(
)
0
.
1
3
4
)
3
.
4
1
(
0
.
1
3
4
M
a
x
.
2
1
1
3
11.18 (0.440)
10.67 (0.420)
2
9
.
6
7
(
0
.
3
8
1
)
9
.
3
8
(
0
.
3
6
9
)
0
.
5
0
(
0
.
0
2
0
)
16.97 (0.668)
1
1
.
5
8
(
0
.
4
5
6
)
0
.
2
6
(
0
.
0
1
0
)
16.87 (0.664)
1
1
.
2
8
(
0
.
4
4
4
)
LM1084MK
LM1084MSM
Pin
1
Fixed
Adjustable
ADJUST
OUTPUT
INPUT
Pin
1
2
Fixed
COMMON
INPUT
Adjustable
ADJUST
INPUT
COMMON
OUTPUT
INPUT
2
Case is OUTPUT
3
LM1084MG
LM1084MIG
Pin
1
2
Fixed
COMMON
OUTPUT
INPUT
Adjustable
Pin
1
2
Fixed
COMMON
OUTPUT
INPUT
Adjustable
ADJUST
OUTPUT
INPUT
ADJUST
OUTPUT
INPUT
3
3
Case is OUTPUT
Case is ISOLATED
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is
believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in
its use. Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
Document Number 6386
Issue 1
E-mail: sales@semelab.co.uk
Website: http://www.semelab.co.uk
相关型号:
©2020 ICPDF网 联系我们和版权申明