STF202.22.TC [SEMTECH]
Data Line Filter, 2 Function(s), 5.25V;型号: | STF202.22.TC |
厂家: | SEMTECH CORPORATION |
描述: | Data Line Filter, 2 Function(s), 5.25V |
文件: | 总7页 (文件大小:176K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
STF202-22 and STF202-30
USB Upstream Port Filter and TVS
For EMI Filtering and ESD Protection
PROTECTION PRODUCTS
Features
Description
The STF202 is a combination EMI filter and line termi-
nation device with integrated TVS diodes for use on
upstream USB ports. It is constructed using a propri-
etary technology that allows passive components and
TVS diodes to be integrated in the same package.
Each device will provide termination, filtering, and ESD
protection for one upstream USB port. The STF202 is
an easily implemented solution for meeting the require-
ments of revision 1.1 of the Universal Serial Bus
specification.
Bidirectional EMI/RFI filtering and line termination
with integrated ESD protection
ESD protection for USB power (VBUS) and data lines
(D+ and D-) to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC 61000-4-4 (EFT) 40A (5/50ns)
Filtering and termination for two USB data lines
Different series resistors for impedance matching
Low TVS operating voltage (5.25V)
Low leakage current
USB line termination is achieved with series 22Ω or
30Ω resistors on both the D+ and D- USB lines. These
resistors preserve signal integrity by matching the cable
impedance to that of the differential driver. The 1.5kΩ
pull-up resistor completes the termination circuit on
each line. This resistor is required by the USB specifi-
cation to identify the equipment as either a full-speed
(connected to D+ line) or low-speed (connected to D-
line) device. The 47pF capacitors are used to bypass
high frequency energy to ground and for edge rate
control of the USB signals. Finally, the STF202 con-
tains TVS diodes for ESD protection of both
Low capacitance
Solid-state technology
Mechanical Characteristics
EIAJ SOT23 6L package
Molding compound flammability rating: UL 94V-0
Marking : Marking Code
Packaging : Tape and Reel per EIA 481
Applications
USB Hubs
(D+ and D-) data lines and the voltage bus (VBUS). The
TVS diodes provide effective suppression of ESD
voltages in excess of ±15kV (air discharge) and ±8kV
(contact discharge) per IEC 61000-4-2, level 4.
The small size and integrated feature of the STF202
minimizes required board space and increases system
reliability. The STF202 is suitable for use in USB hubs,
computers, peripherals, and portable devices.
Portable electronics
Cellular Handsets
Modems
Peripherals
Servers, Desktop, Notebook, and Handheld
Computers
Circuit Diagram
Schematic and PIN Configuration
.
S0T23-6L (Top View)
www.semtech.com
1
Revision 08/11/04
STF202-22 and STF202-30
PROTECTION PRODUCTS
Absolute Maximum Rating
Rating
Symbol
Value
Units
Steady-State Power
Ppk
100
mW
ESD Air Discharge per IEC 61000-4-2
ESD Contact Discharge per IEC 61000-4-2
16
10
VESD
kV
Lead Soldering Temperature
Operating Temperature
Storage Temperature
TL
TJ
260 (10 sec.)
-40 to +125
-55 to +150
°C
°C
°C
TSTG
Electrical Characteristics
STF202-xx
Parameter
Symbol
Conditions
Minimum
Typical
Maximum
Units
TVS Reverse Stand-Off Voltage
TVS Reverse Breakdown Voltage
TVS Reverse Leakage Current
VRWM
VBR
IR
5.25
V
V
It = 1mA
6
VRWM = 5.25V, T=25°C
Between VBUS pin and
Ground
5
1
µA
TVS Reverse Leakage Current
TVS Junction Capacitance
IR
VRWM = 3.3V, T=25°C
Between any data
(D+, D-) pin and Ground.
µA
pF
Cj
Between I/O pins and
Ground, each device
VR = 0V, f = 1MHz
10
Series Resistance (STF202-22)
Series Resistance (STF202-30)
Pull Up Resistance
RS
RS
Each Line
Each Line
Each Line
Each Line
20
27
22
30
1.5
47
24
33
Ω
Ω
RUP
C
1.35
1.65
kΩ
pF
pF
Capacitor
Total Capacitance
CTOT
Between Input or
Output and Ground and
VBUS grounded
60
VR = 0V, f = 1MHz
www.semtech.com
2004 Semtech Corp.
2
STF202-22 and STF202-30
PROTECTION PRODUCTS
Typical Characteristics
ESD Clamping (15kV Air)
ESD Clamping (8kV Contact)
Typical Insertion Loss
Analog Crosstalk (D+ to D-)
0 dB
0 dB
-20 dB
-10 dB
-20 dB
-60 dB
0.030MHz
2.0GHz
0.030 MHz
1 GHz
www.semtech.com
2004 Semtech Corp.
3
STF202-22 and STF202-30
PROTECTION PRODUCTS
Applications Information
Device Connection
Figure 1 - STF202 Circuit Diagram
The STF202 is designed to provide termination, EMI
filtering and ESD protection for two USB I/O lines. The
equivalent circuit diagram is shown in Figure 1. The
device is connected as follows:
.
1 . Full-Speed Devices: For full-speed devices the pull-
up resistor is connected to the D+ line. Pin 1 is
connected to the voltage supply line (VBUS). The
input of the D+ line is routed into pin 3 and out of
pin 4. The input of the D- line is connected at pin 2
and the output at pin 5. Pin 6 is connected to
ground.
Figure 2 - STF202 Connection Diagram
(Full Speed Devices)
2 . Low-Speed Devices: For low speed devices the
pull-up resistor is connected to the D- line. Pins 1
is connected to the voltage supply line (VBUS). The
input of the D- line is connected at pin 3 with the
output taken at pin 4. The input of the D+ line is
connected to pin 2 and the output is at pin 5. Pin
6 is connected to ground.
1
2
3
6
5
4
USB Port Design Considerations
The Universal Serial Bus (USB) specification requires
termination and filtering components for proper opera-
tion. In addition, an open USB socket is vulnerable to
hazardous ESD discharges in excess of 15kV. These
discharges can may occur on the data lines or the
voltage bus. The STF202 is an easily implemented
solution designed to meet the termination and EMI
filter requirements of the USB specification revision
1.1. It also provides ESD protection to IEC 61000-4-2,
level 4.
Semtech provides a complete solution to simplify USB
port design (Figure 4). The STF201 and STF202
integrate all of the components necessary for line
termination, bidirectional EMI filtering, and ESD protec-
tion on downstream (STF201) or upstream (STF202)
ports. The SC5826 is a dual port power switch that
provides individual or ganged port switching, fault
reporting, and inrush current limiting as required by the
USB specification. The SC5205 ULDO provides a
stable voltage to the USB controller.
Board Placement and Layout Guidelines.
A simplified USB port is shown in Figure 3. USB line
termination is achieved with series resistors on both
the D+ and D- lines. These resistors preserve signal
integrity by matching the cable impedance to that of
the differential driver. 15kΩ pull-down resistors are
used to identify a downstream port while an upstream
port is identified with a 1.5KΩ pull up resistor on either
the D+ (full speed devices) or the D- (low speed de-
vices) data line. Capacitors are used to bypass high
frequency energy to ground and for edge rate control
of the USB signals. TVS diodes are added for ESD
protection of both (D+ and D-) data lines and the
voltage bus (VBUS). A power distribution switch and
voltage regulator provide the power management
functions of the port.
Designing a USB hub to meet EMI and ESD immunity
requirements requires a combination of optimum
component placement, trace routing, and good circuit
design practices. Some general guidelines are given
below:
z
Avoid running D+ and D- signal line traces near high
speed clock lines or similar signal lines.
Avoid running critical signal lines near board edges.
Locate the USB controller chip near the USB
connectors.
z
z
z
z
Place the STF202 near the USB connector to
restrict transient coupling.
Minimize the path length between the USB connec-
tor and the STF202
www.semtech.com
2004 Semtech Corp.
4
STF202-22 and STF202-30
PROTECTION PRODUCTS
Applications Information
Figure 3 - USB Port Components
Figure 4 - Typical USB Hub Design
www.semtech.com
2004 Semtech Corp.
5
STF202-22 and STF202-30
PROTECTION PRODUCTS
Outline Drawing - SOT23 6L
A
DIMENSIONS
e1
D
E
INCHES
MILLIMETERS
DIM
A
MIN NOM MAX MIN NOM MAX
H
N
1
-
-
-
-
H
.057
.006 0.00
1.45
0.15
0.90
.035
2X E/2
A1 .000
EI
c
A2 .035 .045 .051 .90 1.15 1.30
GAGE
-
-
-
-
b
.010
.003
.020 0.25
.009 0.08
0.50
0.22
PLANE
2
c
ccc C
D
.110 .114 .118 2.80 2.90 3.00
.060 .063 .069 1.50 1.60 1.75
0.25
L
E1
2X N/2 TIPS
01
e
E
.110 BSC
.037 BSC
.075 BSC
2.80 BSC
0.95 BSC
1.90 BSC
(L1)
e
B
e1
L
DETAIL A
.012 .018 .024 0.30 0.45 0.60
(.024)
6
(0.60)
6
L1
N
D
-
-
01
0°
10°
0°
10°
aaa C
aaa
.004
.008
.008
0.10
0.20
0.20
bbb
ccc
A2
A
SEATING
PLANE
SEE DETAIL A
A1
C
SIDE VIEW
bxN
bbb
C A-B D
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE-H-
3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS
OR GATE BURRS.
Land Pattern -SOT23 6L
X
DIMENSIONS
DIM
INCHES
MILLIMETERS
(.098)
.055
.037
.024
.043
.141
(2.50)
1.40
0.95
0.60
1.10
3.60
C
G
P
X
Y
Z
(C)
G
Z
Y
P
NOTES:
1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
www.semtech.com
2004 Semtech Corp.
6
STF202-22 and STF202-30
PROTECTION PRODUCTS
Marking Codes
Marking
Part Number
Code
STF202-22
STF202-30
222
230
Ordering Information
Qty per
Reel
Part Number
Lead Finish
Reel Size
STF202-22.TC
STF202-30.TC
STF202-22.TCT
STF202-30.TCT
SnPb
SnPb
3,000
3,000
3,000
3,000
7 Inch
7 Inch
7 Inch
7 Inch
Pb free
Pb free
Contact Information
Semtech Corporation
Protection Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805)498-2111 FAX (805)498-3804
www.semtech.com
2004 Semtech Corp.
7
相关型号:
©2020 ICPDF网 联系我们和版权申明