SX1512IULTRT [SEMTECH]
LED Driver, 16-Segment, 4 X 4 MM, 0.40 MM PITCH, HALOGEN FREE AND ROHS COMPLIANT, QFN-28;型号: | SX1512IULTRT |
厂家: | SEMTECH CORPORATION |
描述: | LED Driver, 16-Segment, 4 X 4 MM, 0.40 MM PITCH, HALOGEN FREE AND ROHS COMPLIANT, QFN-28 驱动 接口集成电路 |
文件: | 总42页 (文件大小:1338K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO with LED Driver and Keypad Engine
KEY PRODUCT FEATURES
G
ENERAL DESCRIPTION
The SX1510, SX1511 and SX1512 are complete ultra
low voltage 1.2V to 3.6V General Purpose parallel
Input/Output (GPIO) expanders ideal for low power
handheld battery powered equipment. This family of
GPIOs comes in 4-, 8-, 16-channel configuration and
allows easy serial expansion of I/O through a
standard SPI interface. GPIO devices can provide
additional control and monitoring when the
microcontroller or chipset has insufficient I/O ports, or
in systems where serial communication and control
from a remote location is advantageous.
•
1.2V to 3.6V Low Operating Voltage with Dual
Independent I/O Rails (VCC1, VCC2)
ꢀ
Enable Direct Level Shifting Between I/O
Banks and Host Controller
•
•
5.5V Tolerant I/Os, Up to 15mA Output Sink on
All I/Os (No Total Sink Current Limit)
Integrated LED Driver for Enhanced Lighting
ꢀ
ꢀ
ꢀ
Intensity Control (256-step PWM)
Blink Control (224 On/Off values)
Breathing Control (224 Fade In/Out values)
These devices can also act as a level shifter to
connect a microcontroller running at one voltage level
to a component running at a different voltage level,
thus eliminating the need for extra level translating
circuits. The core is operating as low as 1.425V while
the dual I/O banks can operate between 1.2V and
3.6V independent of the core voltage and each other
(5.5V tolerant).
•
•
On-Chip Keypad Scanning Engine
ꢀ
ꢀ
Support Up to 8x8 Matrix (64 Keys)
Configurable Input Debouncer
4/8/16 Channels of True Bi-directional Style I/O
ꢀ
ꢀ
ꢀ
Programmable Pull-up/Pull-down
Push/Pull or Open-drain outputs
Programmable Polarity
The SX1510, SX1511 and SX1512 feature a fully
programmable LED Driver with internal oscillator for
enhanced lighting control such as intensity (via 256-
step PWM), blinking and breathing (fade in/out) make
them highly versatile for a wide range of LED
applications.
•
•
Open Drain Active Low Interrupt Output (NINT)
ꢀ
ꢀ
Bit Maskable
Programmable Edge Sensitivity
Built-in Clock Management (Internal 2MHz
Oscillator/External Clock Input, 7 clock values)
ꢀ
OSCIO can be Configured as GPO
In addition, keypad application is also supported with
the on-chip scanning engine which enables
continuous keypad monitoring up to 64 keys without
any additional host interaction and further reduce the
bus activity.
•
•
•
•
•
•
•
SPI Compatible Slave Interface (up to 20MHz)
Power-On Reset and Reset Input (NRESET)
Ultra Low Current Consumption of typ. 1uA
-40°C to +85°C Operating Temperature Range
2kV HBM ESD Protection
The SX1510, SX1511 and SX1512 have the ability to
generate mask-programmable interrupts based on
falling/rising edge of any of its GPIO lines. A
dedicated pin indicates to a host controller that a
state change occurred in one or more of the lines.
Each GPIO is programmable via 8-bit configuration
registers such as data registers, direction registers,
pull-up/pull-down registers, interrupt mask registers
and interrupt registers. These I/O expanders come in
small footprint packages and are rated from -40°C t o
+85°C temperature range.
Small Footprint Packages
Pb & Halogen Free, RoHS/WEEE compliant
T
YPICAL APPLICATIONS
•
•
•
Cell phones, PDAs, MP3 players
Digital camera, Notebooks, GPS Units
Any battery powered equipment
O
RDERING INFORMATION
Part Number
SX1510XXX(1)
SX1511IULTRT
SX1512IULTRT
SX1512EVK
I/O Channels
Package
QFN-UT-14
QFN-UT-20
QFN-UT-28
Evaluation Kit
4
8
16
16
(1)
Future product
Rev 1 – 24th Feb. 2010
1
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Table of Contents
G
ENERAL
RDERING
EY
YPICAL
D
ESCRIPTION..................................................................................................................... 1
O
I
NFORMATION................................................................................................................... 1
RODUCT EATURES.................................................................................................................. 1
PPLICATIONS ..................................................................................................................... 1
IN DESCRIPTION ...................................................................................................................... 4
K
P
F
T
1
A
P
1.1
1.2
1.3
1.4
SX1510 4-channel SPI GPIO with LED Driver
4
5
6
7
SX1511 8-channel SPI GPIO with LED Driver and Keypad Engine
SX1512 16-channel SPI GPIO with LED Driver and Keypad Engine
I/Os Feature Summary
2
ELECTRICAL CHARACTERISTICS............................................................................................... 8
2.1
2.2
Absolute Maximum Ratings
Electrical Specifications
8
8
3
4
T
YPICAL
O
PERATING
C
HARACTERISTICS ............................................................................... 11
B
LOCK
D
ETAILED
DESCRIPTION............................................................................................. 13
4.1
4.2
4.3
4.4
SX1510 4-channel SPI GPIO with LED Driver
13
13
14
SX1511 8-channel SPI GPIO with LED Driver and Keypad Engine
SX1512 16-channel SPI GPIO with LED Driver and Keypad Engine
Reset
14
14
15
4.4.1
4.4.2
Hardware (NRESET)
Software (RegReset)
4.5
4.6
SPI Interface
WRITE
15
15
15
4.5.1
4.5.2
READ
I/O Banks
16
16
16
17
18
4.6.1
4.6.2
4.6.3
4.6.4
Input Debouncer
Keypad Scanning Engine
Level Shifter
Polarity Inverter
4.7
4.8
4.9
Interrupt (NINT)
18
19
Clock Management
LED Driver
19
19
20
20
21
21
22
22
4.9.1
4.9.2
4.9.3
4.9.4
4.9.5
4.9.6
4.9.7
Overview
Static Mode
Single Shot Mode
Blink Mode
LED Driver Modes
Synchronization of LED Drivers across several ICs
Tutorial
5
6
C
ONFIGURATION
R
EGISTERS.................................................................................................. 24
5.1
5.2
5.1
SX1510 4-channel GPIO with LED Driver
24
27
31
SX1511 8-channel GPIO with LED Driver and Keypad Engine
SX1512 16-channel GPIO with LED Driver and Keypad Engine
APPLICATION
I
NFORMATION ................................................................................................... 37
6.1
6.2
Typical Application Circuit
Typical LED Connection
37
37
Rev 1 – 24th Feb. 2010
2
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
7
PACKAGING INFORMATION ..................................................................................................... 38
7.1
7.2
7.3
7.4
7.5
7.6
QFN-UT 14-pin Outline Drawing
QFN-UT 14-pin Land Pattern
QFN-UT 20-pin Outline Drawing
QFN-UT 20-pin Land Pattern
QFN-UT 28-pin Outline Drawing
QFN-UT 28-pin Land Pattern
38
38
39
39
40
40
8
SOLDERING PROFILE .............................................................................................................. 41
Rev 1 – 24th Feb. 2010
3
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
1
PIN DESCRIPTION
1.1
SX1510 4-channel SPI GPIO with LED Driver
Pin
X
X
Symbol
NRESET
NSS
Type
DIO
DI
Description
Active low reset
SPI slave select input (active low)
X
SCK
DI
SPI clock input
X
SI
DI
SPI data input
X
X
X
X
X
X
SO
NINT
OSCIO
VDDM
VCC1
GND
DO
DO
DIO
P
P
P
SPI data output (HZ when not used)
Active low interrupt output
Oscillator input/output, can also be used as GPO
Main supply voltage
I/O supply voltage
Ground Pin
I/O[0], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[1], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[2], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[3], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
X
X
X
X
I/O[0]
I/O[1]
I/O[2]
I/O[3]
DIO (*1)
DIO (*1)
DIO (*1)
DIO (*1)
D/I/O/P: Digital/Input/Output/Power
(*1) This pin is programmable through the SPI interface
Table 1 – SX1510 Pin Description
Rev 1 – 24th Feb. 2010
4
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
1.2
SX1511 8-channel SPI GPIO with LED Driver and Keypad Engine
Pin Symbol
Type
DIO
DO
DI
Description
1
2
3
4
NRESET
SO
SCK
SI
Active low reset
SPI data output (HZ when not used)
SPI clock input
SPI data input
DI
I/O[0], at power-on configured as an input
LED driver : Intensity control (PWM)
I/O[1], at power-on configured as an input
LED driver : Intensity control (PWM)
Supply voltage for Bank A I/O[3-0]
Ground Pin
5
6
I/O[0]
I/O[1]
DIO (*1)
DIO (*1)
7
8
VCC1
GND
P
P
I/O[2], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[3], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
Active low interrupt output
SPI slave select input (active low)
Oscillator input/output, can also be used as GPO
Main supply voltage
9
I/O[2]
I/O[3]
DIO (*1)
10
DIO (*1)
11
12
13
14
NINT
NSS
OSCIO
VDDM
DO
DI
DIO
P
I/O[4], at power-on configured as an input
LED driver : Intensity control (PWM)
I/O[5], at power-on configured as an input
LED driver : Intensity control (PWM)
Supply voltage for Bank B I/O[7-4]
Ground Pin
15
16
I/O[4]
I/O[5]
DIO (*1)
DIO (*1)
17
18
VCC2
GND
P
P
I/O[6], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[7], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
19
20
I/O[6]
I/O[7]
DIO (*1)
DIO (*1)
D/I/O/P: Digital/Input/Output/Power
(*1) This pin is programmable through the SPI interface
Table 2 – SX1511 Pin Description
NRESET
SO
I/O[4]
VDDM
OSCIO
NSS
SCK
SI
GND
(PAD)
I/O[0]
NINT
Figure 1 – SX1511 QFN-UT-20 Pinout
Rev 1 – 24th Feb. 2010
5
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
1.3
SX1512 16-channel SPI GPIO with LED Driver and Keypad Engine
Pin Symbol
Type
DIO (*1)
Description
I/O[2], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[3], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
Ground Pin
1
I/O[2]
2
I/O[3]
DIO (*1)
3
4
GND
VCC1
P
P
Supply voltage for Bank A I/O[7-0]
I/O[4], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[5], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[6], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[7], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
Active low interrupt output
5
6
7
8
I/O[4]
I/O[5]
I/O[6]
I/O[7]
DIO (*1)
DIO (*1)
DIO (*1)
DIO (*1)
9
NINT
NSS
OSCIO
VDDM
DO
DI
DO
P
10
11
12
SPI slave select input (active low)
Oscillator input/output, can also be used as GPO
Main supply voltage
I/O[8], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[9], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[10], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[11], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
Ground Pin
13
14
15
16
I/O[8]
I/O[9]
DIO (*1)
DIO (*1)
DIO (*1)
DIO (*1)
I/O[10]
I/O[11]
17
18
GND
VCC2
P
P
Supply voltage for Bank B I/O[15-8]
I/O[12], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[13], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[14], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
I/O[15], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking, Breathing (Fade In/Out)
Active low reset
19
20
21
22
I/O[12]
I/O[13]
I/O[14]
I/O[15]
DIO (*1)
DIO (*1)
DIO (*1)
DIO (*1)
23
24
25
26
NRESET
SO
SCK
SI
DIO
DO
DI
SPI data output (HZ when not used)
SPI clock input
SPI data input
DI
I/O[0], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
I/O[1], at power-on configured as an input
LED driver : Intensity control (PWM), Blinking
27
28
I/O[0]
I/O[1]
DIO (*1)
DIO (*1)
D/I/O/P: Digital/Input/Output/Power
(*1) This pin is programmable through the SPI interface
Table 3 – SX1512 Pin Description
I/O[14]
I/O[13]
I/O[12]
VCC2
GND
21
20
19
18
17
16
15
1
2
3
4
5
6
7
I/O[2]
I/O[3]
GND
TOP VIEW
GND
(PAD)
VCC1
I/O[4]
I/O[5]
I/O[6]
I/O[11]
I/O[10]
Figure 2 – SX1512 QFN-UT-28 Pinout
Rev 1 – 24th Feb. 2010
6
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
1.4
I/Os Feature Summary
SX1510
SX1511
SX1512
I/O
LED Driver
LED Driver
Keypad
LED Driver
Keypad
PWM
Blink Breath
PWM
Blink Breath
Row
Col.
PWM
Blink Breath
Row
Col.
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
0
1
2
3
4
5
6
7
8
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
9
10
11
12
13
14
15
√
√
√
√
Table 4 – I/Os Feature Summary
Please note that in addition to table above, all I/Os feature bank-to-bank and bank-to-host level shifting.
Rev 1 – 24th Feb. 2010
7
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
2
ELECTRICAL
CHARACTERISTICS
2.1
Absolute Maximum Ratings
Table below applies to SX1511 and SX1512. Stress above the limits listed in the following table may cause
permanent failure. Exposure to absolute ratings for extended time periods may affect device reliability. The
limiting values are in accordance with the Absolute Maximum Rating System (IEC 134). All voltages are
referenced to ground (GND).
Symbol
Vmax_VDDM
Vmax_VCC1-2
Description
Min
Max
3.7
Unit
V
Main supply voltage
- 0.4
Digital I/O pin supply voltage
- 0.4
3.7
V
Electrostatic handling HBM model(1) (SX1511)
Electrostatic handling HBM model(1) (SX1512)
Electrostatic handling CDM model
Electrostatic handling MM model (SX1511)
Electrostatic handling MM model (SX1512)
Operating ambient temperature range
Junction temperature range
-
2000
1500
1000
200
150
+85
+125
+150
-
VES_HBM
VES_CDM
VES_MM
V
V
V
-
-
-
-
TA
TC
-40
-40
-55
+/-100
°C
°C
TSTG
Ilat
Storage temperature range
Latchup-free input pin current(2)
°C
mA
(1) Tested according to JESD22-A114A
(2) Static latch-up values are valid at maximum temperature according to JEDEC 78 specification
Table 5 - Absolute Maximum Ratings
2.2
Electrical Specifications
Table below applies to SX1511 and SX1512 with default registers values, unless otherwise specified. Typical
values are given for TA = +25°C, VDDM=VCC1=VCC2=3.3V.
Symbol Description
Conditions
Min
Typ
Max
Unit
Supply
VDDM Main supply voltage
VCC1,2 I/O banks supply voltage
-
-
1.425
1.2
-
-
1
175
10
1
365
10
1
3.6
3.6
5
235
-
5
460
-
V
V
Internal osc. OFF
Internal osc. ON (2MHz)
External osc. (32kHz)
Internal osc. OFF
Internal osc. ON (2MHz)
External osc. (32kHz)
-
-
-
-
-
-
-
Main supply current
(SX1511, SPI inactive)
IDDM
Main supply current
(SX1512, SPI inactive)
ICC1,2 I/O banks supply current(1)
µA
µA
µA
2
I/Os set as Input
0.7*
VCC1,2
0.8*
VCC1,2 >= 2V
VCC1,2 < 2V
VCC1,2 >= 2V
VCC1,2 < 2V
-
-
-
-
5.5(3)
5.5(3)
VIH
VIL
High level input voltage
Low level input voltage
V
V
VCC1,2
0.3*
VCC1,2
0.2*
-0.4
-0.4
VCC1,2
Assuming no active
ILEAK
CI
Input leakage current
Input capacitance
-1
-
-
-
1
µA
pF
pull-up/down
-
10
I/Os set as Output
VCC1,2
– 0.3
-0.4
VOH
VOL
High level output voltage
Low level output voltage
-
-
-
VCC1,2
0.3
V
V
-
Rev 1 – 24th Feb. 2010
8
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Symbol Description
Conditions
Min
Typ
Max
8(2)
Unit
VCC1,2 >= 2V
VCC1,2 < 2V
VCC1,2 >= 2V
VCC1,2 < 2V
After 8th SCK falling
edge
-
-
-
-
-
-
-
-
IOH
IOL
tPV
High level output source current
mA
2(2)
15(2)
8(2)
Low level output sink current
Output data valid timing
mA
ns
-
-
200
NINT (Output)
VOL
IOLM
tIV
Low level output voltage
-
-0.4
-
-
-
-
0.3
8
4
V
mA
ꢀs
VDDM >= 2V
VDDM < 2V
From input data change
From RegInterruptSource
clearing
-
-
-
Low level output sink current
Interrupt valid timing
4
tIR
Interrupt reset timing
-
-
4
ꢀs
NRESET (Input/Output)
VOL
Low level output voltage
-
-0.4
-
-
-
-
-
0.3
8
4
V
VDDM >= 2V
VDDM < 2V
IOLM
Low level output sink current
mA
0.7*
VDDM
0.8*
VDDM
VCC1,2 >= 2V
VCC1,2 < 2V
VCC1,2 >= 2V
VCC1,2 < 2V
-
-
-
-
3.6
3.6
VIHMR High level input voltage
V
V
0.3*
VDDM
0.2*
VDDM
-0.4
-0.4
VILM
Low level input voltage
ILEAK Input leakage current
CI Input capacitance
VPOR Power-On-Reset voltage
VDROPH High brown-out voltage
VDROPL Low brown-out voltage
-
-
-1
-
-
-
-
-
-
1
10
-
-
-
µA
pF
V
V
V
Cf. Figure 7
Cf. Figure 7
Cf. Figure 7
Cf. Figure 7
Cf. Figure 7
0.8
VDDM-1
0.2
-
-
tRESET
tPULSE
Reset time
Reset pulse from host uC
0.6
200
2.5
-
ms
ns
OSCIO (Input/Output)
0.7*
VDDM
0.8*
VDDM
+0.3
VDDM
+0.3
0.3*
VDDM
0.2*
VCC1,2 >= 2V
VCC1,2 < 2V
VCC1,2 >= 2V
VCC1,2 < 2V
-
-
-
-
VIHMA High level input voltage
V
V
VDDM
-0.4
-0.4
VILM
Low level input voltage
VDDM
1
ILEAK Input leakage current
CI Input capacitance
-
-
-1
-
-
-
µA
pF
10
VDDM –
VOHM High level output voltage
-
-
VDDM
V
V
0.3
-0.4
-
-
-
-
VOL
Low level output voltage
-
-
-
-
-
-
0.3
8
2
8
4
VDDM >= 2V
VDDM < 2V
VDDM >= 2V
VDDM < 2V
IOHM
High level output source current
mA
IOLM
Low level output sink current
mA
V
SPI Interface : NSS(Input), SCK(Input), SI(Input), SO(Output)
0.7*
VDDM
0.8*
VDDM
+0.3
VDDM
+0.3
0.3*
VDDM
0.2*
VDDM
1
10
VCC1,2 >= 2V
-
-
-
-
VIHMA
VILM
High level input voltage
Low level input voltage
VCC1,2 < 2V
VCC1,2 >= 2V
VCC1,2 < 2V
VDDM
-0.4
-0.4
V
ILEAK
CI
Input leakage current
Input capacitance
-
-
-1
-
-
-
µA
pF
Rev 1 – 24th Feb. 2010
9
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Symbol Description
Conditions
Min
VDDM –
Typ
Max
Unit
V
VOHM
VOL
High level output voltage
-
-
VDDM
0.3
-0.4
-
Low level output voltage
-
-
-
-
0.3
8
2
V
VDDM >= 2V
VDDM < 2V
IOHM
High level output source current
mA
-
VDDM >= 2V
VDDM < 2V
-
-
-
45
45
9
9
-
-
8
4
-
55
55
-
IOLM
Low level output sink current
mA
-
fSCK
SCK max clock frequency
SCK low time (% of SCK cycle)
SCK high time (% of SCK cycle)
SI setup time
-
-
-
-
20(4)
MHz
%
%
ns
ns
%
ns
ns
ns
tSCK,LOW
tSCK,HIGH
tSI,SETUP
tSI,HOLD
tSO,VALID
tNSS,SCK
tSCK,NSS
tNSS,HIGH
-
-
-
-
-
-
-
-
SI hold time
-
-
SO valid time (% of SCK cycle)
NSS low to SCK rising edge
SCK falling edge to NSS high
NSS rising to falling edge
After SCK falling edge
33(4)
-
-
-
25
25
25
-
-
-
Miscellaneous
Programmable pull-up/down
resistors for IO[0-7]
RPULL
-
-
42
-
kꢁ
Internal
External from OSCIN
1.3
-
2
-
2.6
2.6
fOSC
Oscillator frequency
MHz
(1) Assuming no load connected to outputs and inputs fixed to VCC1,2 or GND.
(2) Can be increased by tying together and driving simultaneously several I/Os.
(3) With RegHighInput bit enabled (VCCx min =1.65V), else 3.6V (VCCx min = 1.2V)
(4) fSCK is calculated assuming a tSO,VALID of maximum 1/3 of SCK cycle. This gives 1/6 of SCK cycle as setup time to the host controller.
For systems where the setup time can be relaxed, tSO,VALID is also shown in §3 to allow the user to calculate the maximum SPI frequency
for individual systems.
Table 6 – Electrical Specifications
Rev 1 – 24th Feb. 2010
10
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
3
TYPICAL OPERATING CHARACTERISTICS
SX1512 IDDM vs.VDDM (Oscillator Enabled)
SX1512 IDDM vs.VDDM (Oscillator Enabled)
360
360
340
320
300
280
260
240
220
340
320
300
280
260
240
220
200
180
200
180
160
140
120
100
160
140
120
100
1.3
1.5
1.7
1.9
2.1
2.3
2.5
2.7
2.9
3.1
3.3
3.5
1.3
1.5
1.7
1.9
2.1
2.3
2.5
2.7
2.9
3.1
3.3
3.5
VDDM (V)
VDDM (V)
Fosc vs. VDDM
Fosc vs.Temperature (VDDM
=
3.6V)
2.5
2.3
2.1
1.9
1.7
2.5
2.3
2.1
1.9
1.7
1.5
1.3
1.5
1.3
1.3
1.5
1.7
1.9
2.1
2.3
2.5
2.7
2.9
3.1
3.3
3.5
-50
-30
-10
10
30
50
70
90
VDDM (V)
Temp
(
oC)
VOL vs.Temperature (VCCx
=
3.6V, IOL = 15mA)
VOL vs. IOL (VCCx
= 3.6V, Temp 25C)
0.3
0.3
0.25
0.25
0.2
0.15
0.1
0.05
0
0.2
0.15
0.1
0.05
0
0
2
4
6
8
IOL (mA)
10
12
14
-50
-30
-10
10
30
50
70
90
Temp
(
oC)
VOH vs. IOH (VDDM
= 3.6V, Temp 25C)
VOH vs. Temperature (VCCx
=
3.6V, IOH
=
8mA)
3.6
3.55
3.5
3.6
3.55
3.5
3.45
3.4
3.45
3.4
3.35
3.3
3.35
3.3
3.25
3.2
3.25
3.2
-50
-30
-10
10
30
50
70
90
-8
-7
-6
-5
-4
IOH (mA)
-3
-2
-1
0
Temp
(
oC)
Rev 1 – 24th Feb. 2010
11
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
SCK
t
SO,VALID
vs. VDDM
f
vs. VDDM
90
80
70
60
50
40
30
20
10
30
25
20
15
10
5
0
1.3
1.5
1.7
1.9
2.1
2.3
2.5
2.7
2.9
3.1
3.3
3.5
3.7
1.3
1.5
1.7
1.9
2.1
2.3
2.5
2.7
2.9
3.1
3.3
3.5
3.7
VDDM (V)
VDDM (V)
Worst Case
Typical
Worst Case
Typical
Figure 3 – Typical Operating Characteristics
Rev 1 – 24th Feb. 2010
12
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
4
BLOCK
DETAILED DESCRIPTION
4.1
SX1510 4-channel SPI GPIO with LED Driver
OSCIO
Clock Mgmt
LED Driver
External
Clock
Intensity (PWM)
Blink (Timer)
Internal
Oscillator
Breath (Ramp)
VDDM
Reset
VCC1
I/O[0]
I/O[1]
I/O[2]
I/O[3]
NRESET
4-Bit
SPI Bus
Control
I/O Bank A
R/W
NSS
SCK
SI
SO
NINT
Interrupt
GND
Figure 4 – 4-channel Low Voltage GPIO with LED Driver
4.2
SX1511 8-channel SPI GPIO with LED Driver and Keypad Engine
OSCIO
Keypad
Engine
Clock Mgmt
External
Clock
LED Driver
Intensity (PWM)
Blink (Timer)
16 Keys Max
Internal
Oscillator
Breath (Ramp)
VCC1
I/O[0]
I/O[1]
I/O[2]
I/O[3]
VDDM
I/O Bank A
Reset
NRESET
8-Bit
R/W
SPI Bus
Control
NSS
SCK
SI
VCC2
I/O[4]
I/O[5]
I/O[6]
I/O[7]
I/O Bank B
Interrupt
SO
SX1511
NINT
GND
Figure 5 – 8-channel Low Voltage GPIO with LED Driver and Keypad Engine
Rev 1 – 24th Feb. 2010
13
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
4.3
SX1512 16-channel SPI GPIO with LED Driver and Keypad Engine
OSCIO
Keypad
Engine
Clock Mgmt
External
Clock
LED Driver
Intensity (PWM)
64 Keys Max
Blink (Timer)
Internal
Oscillator
Auto
Sleep/Wakeup
Breath (Ramp)
VCC1
I/O[0]
I/O[1]
I/O[2]
I/O[3]
I/O[4]
I/O[5]
I/O[6]
I/O[7]
I/O Bank A
VDDM
8-Bit
R/W
Reset
NRESET
SPI Bus
Control
NSS
SCK
SI
VCC2
I/O[8]
I/O[9]
I/O[10]
I/O[11]
I/O[12]
I/O[13]
I/O[14]
I/O[15]
8-Bit
R/W
SO
I/O Bank B
Interrupt
NINT
GND
Figure 6 – 16-channel Low Voltage GPIO with LED Driver and Keypad Engine
4.4
Reset
4.4.1 Hardware (NRESET)
The SX1510, SX1511 and SX1512 generate their own power on reset signal after a power supply is connected
to the VDDM pin. The reset signal is made available for the user at the pin NRESET. The rising edge of the
NRESET indicates that the startup sequence of the SX1510, SX1511 or SX1512 has finished. NRESET must be
connected to VDDM (or greater) either directly, or via a resistor.
2
1
2
3
4
5
6
1
VDROPH
VPOR
VDROPL
VDDM
Undefined
Undefined
Undefined
NRESET
tRESET
tPULSE
tRESET
Figure 7 – Power-On / Brown-out Reset Conditions
1. Device behavior is undefined until VDDM rises above VPOR, at which point NRESET is driven to GND
by the SX1510, SX1511 or SX1512.
2. After tRESET, NRESET is released (high-impedance) by the SX1510, SX1511 or SX1512 to allow it to be
pulled high by an external resistor.
Rev 1 – 24th Feb. 2010
14
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
3. In operation, the SX1510, SX1511 and SX1512 may be reset (POR like or LED driver counters only
depending on RegMisc setting) at anytime by an external device driving NRESET low during tPULSE
Chip can be accessed normally again after NRESET rising edge.
.
4. During a brown-out event, if VDDM drops above VDROPH a reset will not occur.
5. During a brown-out event, if VDDM drops between VDROPH and VDROPL a reset may occur.
6. During a brown-out event, if VDDM drops below VDROPL a reset will occur next time VPOR is crossed.
Please note that a brown-out event is defined as a transient event on VDDM. If VDDM is attached to a battery,
then the gradual decay of the battery voltage will not be interpreted as a brown-out event.
Please also note that a sharp rise in VDDM (> 1V/us) may induce a circuit reset.
4.4.2 Software (RegReset)
Writing consecutively 0x12 and 0x34 to RegReset register will reset all registers to their default values.
4.5
SPI Interface
The SX1510, SX1511 and SX1512 SPI interface operates only in slave mode. 4 lines are used to exchange data
between an external master host and the slave device:
•
•
•
•
NSS : Slave select input (active low)
SCK : Clock input
SI : Data input
SO : Data output
The SX1510, SX1511 and SX1512 have a few user-accessible internal 8-bits registers to set the various
parameters of operation (Cf. §5 for detailed configuration registers description). The SPI interface has been
designed for program flexibility, in that any register can be written or read independently of each other.
4.5.1 WRITE
To write a value into a configuration register the timing diagram below should be carefully followed by the uC.
NSS
SCK
SI
SO
Figure 8 - SPI Write Operation
Successive register data can be written by the master without repeating the address byte, the register address
can be automatically incremented or kept fixed depending on the setting programmed in RegMisc.
4.5.2
READ
To read a value from a configuration register the timing diagram below should be carefully followed by the uC.
NSS
SCK
SI
SO
Figure 9 – SPI Read Operation
Rev 1 – 24th Feb. 2010
15
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Successive register data can be read by the master without repeating the address byte, the register address will
be automatically incremented or kept fixed depending on the setting programmed in RegMisc.
4.6
I/O Banks
4.6.1 Input Debouncer
Each input can be individually debounced by setting corresponding bits in RegDebounce register. At power up
the debounce function is disabled. After enabling the debouncer, the change of the input value is accepted only if
the input value is identical at two consecutive sampling times.
The debounce time common to all IOs can be set in RegDebounceConfig register from 0.5 to 64ms.(fOSC =
2MHz)
4.6.2 Keypad Scanning Engine
SX1511, and SX1512 integrate a fully programmable keypad scanning engine to implement keypad applications
up to 8x8 matrix (i.e. 64 keys).
Please note that SX1512 also implements an Auto Sleep/Wakeup feature to save power consumption when no
key has been pressed for a programmed time.
Y
SX1511
IO3
IO2
IO1
IO0
X
IO4
IO5
IO6
IO7
RegKeyData =
- IO[3-0] as outputs (scanning)
- IO[7-4] as inputs
X
Y
Figure 10 – 4x4 Keypad Connection to SX1511
Following procedure should be implemented on the host controller for a 4x4 keypad:
1. Set RegDir to 0xF0 (IO[3-0] as outputs, IO[7-4] as inputs) , set RegOpenDrain to 0x0F (IO[3-0] as open-drain
outputs), set RegPullup to 0xF0 (pull-ups enabled on inputs IO[7-4]).
2. Enable and configure debouncing on IO[7-4] (RegDebounceEnable = 0xF0, Ex : RegDebounceConfig = 0x05)
3. Enable and configure keypad scanning engine (Ex : RegKeyConfig = 0x7D) This will start an infinite loop with
the following sequence to IO[3:0]: ZZZ0, ZZ0Z, Z0ZZ, 0ZZZ. Make sure that scan interval is set to higher value
than the debounce time.
4. When a key is pressed, NINT goes low, key scan is halted and the key coordinates are stored in RegKeyData:
•
•
•
The column data will be stored in RegKeyData[7:4] (Note: column indication is active low)
The row data will be stored in RegKeyData[3:0] (Note: row indication is active low)
When RegKeyData is read, this data along with the interrupt is automatically cleared (same behavior
as reading RegData) and the key scan continues to the next row.
5. Restart from point 4.
This implementation allows the host to handle both single and multi-touches easily (fast AAAAAA sequence is a
long press of key A, fast ABABABAB sequence is key A and key B pressed together, etc)
Rev 1 – 24th Feb. 2010
16
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
4.6.3 Level Shifter
Because of their 5.5V tolerant I/O banks with independent supply voltages between 1.2V and 3.6V, the SX1511
and SX1512 can perform level shifting of signals from one I/O bank to another without uC activity by
programming the corresponding configuration register bits accordingly in RegLevelShifter (and RegDir).
This can save significant BOM cost in a final application where only a few signals need to be level-shifted (no
need for an additional external level shifter IC).
1.2-3.6V
VCC1
1.2-5.5V
IO0
SX1510/11
1.2-3.6V
1.2-3.6V
VCC2
IO4
Figure 11 – Level Shifting Example
The minimum pulse width tLevelShiftMin which can be level shifted properly depends on VCCx and VDDM:
tLevelShiftMin = Input Delay + Core Delay + Output Delay
Input/Core/Output delays vs VCCx/VDDM are given in figures below.
Rev 1 – 24th Feb. 2010
17
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
IO Input Delay vs. Supply Voltage
10.000
9.000
8.000
7.000
6.000
5.000
4.000
3.000
2.000
1.000
0.000
1.000
1.500
2.000
2.500
VCCx (V)
3.000
3.500
Typical
Worst Case
SX1512 Digital Core Delay vs. Supply Voltage
SX1511 Digital Core Delay vs. Supply Voltage
28
26
24
22
20
18
16
14
28
26
24
22
20
18
16
14
1
1.5
2
2.5
3
3.5
1
1.5
2
2.5
3
3.5
VDDM (V)
VDDM (V)
Typical
Worst Case
Typical
Worst Case
IO Output Delay vs. Supply Voltage ( LowDriveEn=0, 20pF Load)
IO Output Delay vs. Supply Voltage (LowDriveEn=1, 20pF Load)
140.000
120.000
100.000
80.000
60.000
40.000
20.000
0.000
140.000
120.000
100.000
80.000
60.000
40.000
20.000
0.000
1.000
1.500
2.000
2.500
VCCx (V)
3.000
3.500
1.000
1.500
2.000
2.500
3.000
3.500
VCCx (V)
Typical
Worst Case
Typical
Worst Case
Figure 12 – Level Shifter Max Frequency Calculation Data
4.6.4 Polarity Inverter
Each IO’s polarity can be individually inverted by setting corresponding bit in RegPolarity register. Please note
that polarity inversion can also be combined with level shifting feature.
4.7
Interrupt (NINT)
At start-up, the transition detection logic is reset, and NINT is released to a high-impedance state. The interrupt
mask register is set to 0xFF, disabling the interrupt output for transitions on all I/O ports. The transition flags are
cleared to indicate no data changes.
An interrupt NINT can be generated on any programmed combination of I/Os rising and/or falling edges through
the RegInterruptMask and RegSense registers.
If needed, the I/Os which triggered the interrupt can then be identified by reading RegInterruptSource register.
When NINT is low (i.e. interrupt occurred), it can be reset back high (i.e. cleared) by writing 0xFF in
RegInterruptSource (this will also clear corresponding bits in RegEventStatus register).
The interrupt can also be cleared automatically when reading RegData register (Cf. RegMisc)
Example: We want to detect rising edge of I/O[1] on SX1511 (NINT will go low).
Rev 1 – 24th Feb. 2010
18
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
1. We enable interrupt on I/O[1] in RegInterruptMask
ꢁ RegInterruptMask =“XXXXXX0X”
2. We set edge sense for I/O[1] in RegSense
ꢁ RegSenseLow =“XXXX01XX”
Please note that independently from the “user defined” process described above the keypad engine, when
enabled, also uses NINT to indicate a key press.
Hence we have NINT = “user defined condition occurred” OR “keypad engine condition occurred”
4.8
Clock Management
A main oscillator clock fOSC is needed by the LED driver, keypad engine and debounce features.
Clock management block is illustrated in figure below.
OSCIO
Clock
Mgmt
External
Clock
Div
fOSC
Internal
Oscillator
Figure 13 – Clock Management Overview
The block is configured in register RegClock (Cf §5 for more detailed information):
ꢂ
ꢂ
ꢂ
Selection of internal clock source: none (OFF) or internal oscillator or external clock input from OSCIN.
Definition of OSCIO pin function (OSCIN or OSCOUT)
OSCOUT frequency setting (sub-multiple of fOSC)
Please note that if needed the OSCOUT feature can be used as an additional GPO (Cf. RegClock)
4.9
LED Driver
4.9.1 Overview
Every IO has its own independent LED driver to perform intensity control, blinking and fading operation. (Cf §6.2
for typical LED connection)
Please note that while all I/Os can perform intensity control (PWM) only some of them additionally include
blinking and breathing features (Cf pin description §1)
The LED drivers of all I/Os share the same clock ClkX configurable in RegMisc[6:4]. Please note that for power
consumption reasons ClkX is OFF by default.
Assuming ClkX is not OFF, LED driver for IO[X] is enabled when RegLEDDriverEnable[X] = 1 in which case it
can operate in one of the three modes below:
•
•
•
Static mode (all I/Os, with or without fade in/out)
Single shot mode (blinking capable I/Os only, with or without fade in/out)
Blink mode (blinking capable I/Os only, with or without fade in/out)
Rev 1 – 24th Feb. 2010
19
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
RegData[X]
1
0
t
IO[X] Intensity (PWM value)
100%
ON
IOnX
Fade In
Fade Out
OFF
IOffX
0
t
TRiseX
TOnX
TFallX
TOffX
Figure 14 – LED Driver Overview
Each IO[X] has its own set of programmable registers (Cf §5 for more detailed information):
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
RegTOnX (blinking capable I/Os only): TOnX, ON time of IO[X]
RegIOnX (all I/Os): IOnX, ON intensity of IO[X]
RegOffX (blinking capable I/Os only): TOffX and IOffX, OFF time and intensity of IO[X]
RegTRiseX(breathing capable I/Os only): TRiseX, fade in time of IO[X]
RegTFallX(breathing capable I/Os only): TFallX, fade out time of IO[X]
Please note that the LED Driver mode is selectable for each IO bank between linear and logarithmic. (Cf 4.9.5)
All the figures assume normal IO polarity, for inverse polarity RegData control must be inverted (does not invert
the polarity of the IO signal itself).
4.9.2 Static Mode
Only mode available for non blinking capable IOs (with Off intensity = 0), else invoked when TOnX = 0.
If the I/O doesn’t support fading the LED intensity will step directly to the IOnX/IOffX value.
RegData(X)
On intensity(max) determined by
register RegIOnX
IOLED(X) level
Off intensity(min) determined by
register RegIOffX
Fade in rate determined by
register RegTRiseX
Fade out rate determined
by register RegTFallX
Figure 15 – LED Driver Static Mode
4.9.3 Single Shot Mode
Invoked when TOnX != 0 and TOffX = 0.
If the I/O doesn’t support fading the LED intensity will step directly to the IOnX/IOffX value.
Rev 1 – 24th Feb. 2010
20
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
RegData(X)
On intensity(max)
IOLED(X) level
Off intensity(min)
Fade in rate determined by
register RegTRiseX
Minimum intensity duration
determined by register
RegData(x)
Fade out rate determined
by register RegTFallX
Figure 16 – LED Driver Single Shot Mode
4.9.4 Blink Mode
Invoked when TOnX != 0 and TOffX != 0.
If the I/O doesn’t support fading the LED intensity will step directly to the IOnX/IOffX value.
When RegData(X) is cleared, the LED
will complete any current ramp, and then
stay at minimum intensity
RegData(X)
On intensity(max)
IOLED(X) level
Off intensity(min)
Fade in rate determined by
register RegTRiseX
Maximum intensity
duration determined by
register RegTOnX
Minimum intensity duration
determined by register
RegTOffX
Fade out rate determined
by register RegTFallX
Figure 17 – LED Driver Blink Mode
4.9.5 LED Driver Modes
For each IO bank, the LED driver mode of fading capable IOs can be selected between linear or logarithmic in
RegMisc.
Lin. Log. Lin. Log. Lin. Log. Lin. Log. Lin. Log. Lin. Log. Lin. Log. Lin. Log.
0
1
2
3
4
5
6
7
8
0
0
0
0
0
0
0
0
1
1
1
1
1
1
32
33
34
35
36
37
38
39
40
41
42
43
44
45
4
4
4
4
5
5
5
5
6
6
6
6
7
7
64
65
66
67
68
69
70
71
72
73
74
75
76
77
13
13
13
13
14
14
14
14
16
16
17
17
18
18
96
97
98
99
28
28
30
30
31
31
32
32
34
34
35
35
36
36
128
129
130
131
132
133
134
135
136
137
138
139
140
141
53
53
53
53
56
56
56
56
60
60
60
60
65
65
160
161
162
163
164
165
166
167
168
169
170
171
172
173
88
88
88
88
93
93
93
93
98
98
98
98
104
104
192
193
194
195
196
197
198
199
200
201
202
203
204
205
135
135
135
135
142
142
142
142
150
150
150
150
157
157
224
225
226
227
228
229
230
231
232
233
234
235
236
237
198
198
198
198
207
207
207
207
216
216
216
216
225
225
100
101
102
103
104
105
106
107
108
109
9
10
11
12
13
Rev 1 – 24th Feb. 2010
21
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
7
7
8
8
8
8
9
9
9
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
19
19
20
20
21
21
22
22
23
23
24
24
25
25
26
26
27
27
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
38
38
39
39
41
41
42
42
44
44
46
46
46
46
49
49
49
49
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
65
65
69
69
69
69
73
73
73
73
78
78
78
78
83
83
83
83
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
104
104
110
110
110
110
116
116
116
116
122
122
122
122
129
129
129
129
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
157
157
165
165
165
165
172
172
172
172
181
181
181
181
189
189
189
189
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
225
225
235
235
235
235
245
245
245
245
255
255
255
255
255
255
255
255
9
10
10
10
10
11
11
12
12
Table 7 – LED Driver Linear vs Logarithmic Function (I)
300
250
200
150
100
50
Linear mode
Log mode
0
1
10 19 28 37 46 55 64 73 82 91 100 109 118 127 136 145 154 163 172 181 190 199 208 217 226 235 244 253
RegIOn (4xRegOff[2:0])
Figure 18 – LED Driver Linear vs Logarithmic Function (II)
4.9.6 Synchronization of LED Drivers across several ICs
When several GPIO expanders are used in the same application it may be useful that their LEDs drivers are
synchronous for coherent global operation.
In this case all ICs should share their fOSC through their OSCIO pins and have their NRESET pins connected
together.
When RegMisc of each IC is set accordingly, NRESET signal can then be used to reset all devices’ internal
counters (but not the register settings) and allow synchronous LED operation (blinking, fading) across multiple
devices.
4.9.7 Tutorial
Below are the steps required to use the LED driver with the typical LED connection described §6.2:
-
-
Disable input buffer (RegInputDisable)
Disable pull-up (RegPullUp)
Rev 1 – 24th Feb. 2010
22
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
-
-
-
-
-
-
-
Enable open drain (RegOpenDrain)
Set direction to output (RegDir) – by default RegData is set high => LED OFF
Enable oscillator (RegClock)
Configure LED driver clock and mode if relevant (RegMisc)
Enable LED driver operation (RegLEDDriverEnable)
Configure LED driver parameters (RegTOn, RegIOn, RegOff, RegTRise, RegTFall)
Set RegData bit low => LED driver started
Rev 1 – 24th Feb. 2010
23
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
5
CONFIGURATION
REGISTERS
5.1
SX1510 4-channel GPIO with LED Driver
Address Name
Description
Default
Device and IO Banks
0x00
0x01
RegInputDisable
Input buffer disable register
XXXX 0000
XXXX 0000
XXXX 0000
XXXX 0000
XXXX 0000
XXXX 0000
XXXX 0000
XXXX 1111
XXXX 1111*
XXXX 1111
0000 0000
XXXX 0000
XXXX 0000
0000 0000
0000 0000
XXXX 0000
RegLongSlew
RegLowDrive
RegPullUp
Output buffer long slew register
Output buffer low drive register
Pull-up register
0x02
0x03
0x04
RegPullDown
RegOpenDrain
RegPolarity
Pull-down register
0x05
Open drain register
0x06
Polarity register
0x07
RegDir
Direction register
0x08
RegData
Data register
0x09
RegInterruptMask
RegSense
Interrupt mask register
Sense register
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
Debounce
0x10
RegInterruptSource
RegEventStatus
RegClock
Interrupt source register
Event status register
Clock management register
Miscellaneous device settings register
LED driver enable register
RegMisc
RegLEDDriverEnable
RegDebounceConfig
RegDebounceEnable
Debounce configuration register
Debounce enable register
0000 0000
XXXX 0000
0x11
LED Driver (PWM, blinking, breathing)
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
0x21
0x22
0x23
RegTOn0
RegIOn0
RegOff0
ON time register for I/O[0]
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
ON intensity register for I/O[0]
OFF time/intensity register for I/O[0]
ON time register for I/O[1]
RegTOn1
RegIOn1
RegOff1
ON intensity register for I/O[1]
OFF time/intensity register for I/O[1]
Fade in register for I/O[1]
RegTRise1
RegTFall1
RegTOn2
RegIOn2
RegOff2
Fade out register for I/O[1]
ON time register for I/O[2]
ON intensity register for I/O[2]
OFF time/intensity register for I/O[2]
Fade in register for I/O[2]
RegTRise2
RegTFall2
RegTOn3
RegIOn3
RegOff3
Fade out register for I/O[2]
ON time register for I/O[3]
ON intensity register for I/O[3]
OFF time/intensity register for I/O[3]
Fade in register for I/O[3]
RegTRise3
RegTFall3
Fade out register for I/O[3]
Software Reset
0x7D
RegReset
Software reset register
0000 0000
Test (not to be written)
0x7E
0x7F
RegTest1
RegTest2
Test register
Test register
0000 0000
0000 0000
*Bits set as output take “1” as default value.
Table 8 – SX1510 Configuration Registers Overview
Rev 1 – 24th Feb. 2010
24
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Addr Name
Default Bits Description
7:4
3:0
7:4
3:0
7:4
3:0
7:4
3:0
7:4
3:0
7:4
3:0
7:4
3:0
7:4
3:0
Unused
Disables the input buffer of each IO
0 : Input buffer is enabled (input actually being used)
1 : Input buffer is disabled (input actually not being used or LED connection)
0x00
0x01
0x02
0x03
0x04
0x05
0x06
RegInputDisable
0xX0
0xX0
0xX0
0xX0
0xX0
0xX0
0xX0
Unused
Enables increased slew rate of the output buffer of each [output-configured] IO
0 : Increased slew rate is disabled
1 : Increased slew rate is enabled
RegLongSlew
RegLowDrive
RegPullUp
Unused
Enables reduced drive of the output buffer of each [output-configured] IO
0 : Reduced drive is disabled
1 : Reduced drive is enabled
Unused
Enables the pull-up for each IO
0 : Pull-up is disabled
1 : Pull-up is enabled
Unused
Enables the pull-down for each IO
0 : Pull-down is disabled
1 : Pull-down is enabled
RegPullDown
RegOpenDrain
RegPolarity
Unused
Enables open drain operation for each [output-configured] IO
0 : Regular push-pull operation
1 : Open drain operation
Unused
Enables polarity inversion for each IO
0 : Normal polarity : RegData[x] = IO[x]
1 : Inverted polarity : RegData[x] = !IO[x] (for both input and output configured IOs)
Unused
Configures direction for each IO.
0 : IO is configured as an output
1 : IO is configured as an input
0x07
0x08
0x09
RegDir
0xXF
0xXF
0xXF
7:4
3:0
7:4
Unused
RegData
Write: Data to be output to the output-configured IOs
Read: Data seen at the IOs, independent of the direction configured.
Unused
Configures which [input-configured] IO will trigger an interrupt on NINT pin
0 : An event on this IO will trigger an interrupt
1 : An event on this IO will NOT trigger an interrupt
RegInterruptMask
3:0
7:6
5:4
3:2
1:0
7:4
Edge sensitivity of RegData[3]
Edge sensitivity of RegData[2]
Edge sensitivity of RegData[1]
Edge sensitivity of RegData[0]
00 : None
01 : Rising
10 : Falling
11 : Both
0x0A
0x0B
RegSense
0x00
0xX0
Unused
Interrupt source (from IOs set in RegInterruptMask)
0 : No interrupt has been triggered by this IO
1 : An interrupt has been triggered by this IO (an event as configured in relevant
RegSense register occured).
RegInterruptSource
3:0
7:4
3:0
Writing '1' clears the bit in RegInterruptSource and in RegEventStatus
When all bits are cleared, NINT signal goes back high.
Unused
Event status of all IOs.
0 : No event has occured on this IO
1 : An event has occured on this IO (an edge as configured in relevant RegSense
register occured).
0x0C
RegEventStatus
0xX0
Writing '1' clears the bit in RegEventStatus and in RegInterruptSource if relevant.
If the edge sensitivity of the IO is changed, the bit(s) will be cleared automatically
7
Unused
Oscillator frequency (fOSC) source
00 : OFF. LED driver and debounce features are disabled.
01 : External clock input (OSCIN)
10 : Internal 1MHz oscillator
6:5
11 : Reserved
OSCIO pin function (Cf. §4.8)
0x0D
RegClock
0x00
4
0 : OSCIO is an input (OSCIN)
1 : OSCIO is an output (OSCOUT)
Frequency of the signal output on OSCOUT pin:
0x0 : 0Hz, permanent "0" logical level (GPO)
0xF : 0Hz, permanent "1" logical level (GPO)
Else : fOSCOUT = fOSC/(2^(RegClock[3:0]-1))
3:0
Rev 1 – 24th Feb. 2010
25
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
7
Unused
Frequency of the LED Driver clock ClkX of all IOs:
0 : OFF. LED driver functionality is disabled for all IOs.
Else : ClkX = fOSC/(2^(RegMisc[6:4]-1))
6:4
LED Driver mode for Bank A ‘s fading capable IOs (IO1-3)
0: Linear
1: Logarithmic
NRESET pin function when externally forced low (Cf. §4.4.1 and §4.9.5)
0: Equivalent to POR
1: Reset PWM/Blink/Fade counters (not user programmed values)
This bit can only be reset manually or by POR, not by NRESET.
Auto-increment register address (Cf. §4.5)
0: ON. When several consecutive data are read/written, register address is incremented.
1: OFF. When several consecutive data are read/written, register address is kept fixed.
Autoclear NINT on RegData read (Cf. §4.7)
0: ON. RegInterruptSource is also automatically cleared when RegData is read.
1: OFF. RegInterruptSource must be manually cleared, either directly or via
RegEventStatus.
3
2
1
0
0x0E
RegMisc
0x00
7:4
3:0
7:3
Unused
Enables LED Driver for each [output-configured] IO
0 : LED Driver is disabled
1 : LED Driver is enabled
0x0F
0x10
0x11
RegLEDDriverEnable
RegDebounceConfig
RegDebounceEnable
0xX0
0x00
0xX0
Unused
Debounce time (Cf. §4.6.1)
000: 0.5ms x 1MHz/fOSC
001: 1ms x 1MHz/fOSC
010: 2ms x 1MHz/fOSC
011: 4ms x 1MHz/fOSC
100: 8ms x 1MHz/fOSC
101: 16ms x 1MHz/fOSC
110: 32ms x 1MHz/fOSC
111: 64ms x 1MHz/fOSC
2:0
7:4
3:0
7:5
Unused
Enables debouncing for each [input-configured] IO
0 : Debouncing is disabled
1 : Debouncing is enabled
Unused
ON Time of IO[X]:
0xXX
0xXX
RegTOnX
RegIOnX
0x00
0xFF
0 : Infinite (Static mode, TOn directly controlled by RegData, Cf §4.9.2)
1 - 15 : TOnX = 64 * RegTOnX * (255/ClkX)
16 - 31 : TOnX = 512 * RegTOnX * (255/ClkX)
ON Intensity of IO[X]
- Linear mode : IOnX = RegIOnX
- Logarithmic mode (fading capable IOs only) : IOnX = f(RegIOnX) , Cf §4.9.5
OFF Time of IO[X]:
0 : Infinite (Single shot mode, TOff directly controlled by RegData, Cf §4.9.3)
1 - 15 : TOffX = 64 * RegOffX[7:3] * (255/ClkX)
16 - 31 : TOffX = 512 * RegOffX[7:3] * (255/ClkX)
OFF Intensity of IO[X]
4:0
7:0
7:3
0xXX
0xXX
RegOffX
0x00
0x00
2:0
7:5
- Linear mode : IOffX = 4 x RegOff[2:0]
- Logarithmic mode (fading capable IOs only) : IOffX = f(4 x RegOffX[2:0]) , Cf §4.9.5
Unused
Fade In setting of IO[X]
RegTRiseX
0 : OFF
4:0
7:5
4:0
1 - 15 : TRiseX = (RegIOnX-(4xRegOffX[2:0])) * RegTRiseX * (255/ClkX)
16 - 31 : TRiseX = 16 * (RegIOnX-(4xRegOffX[2:0])) * RegTRiseX * (255/ClkX)
Unused
Fade Out setting of IO[X]
0 : OFF
1 - 15 : TFallX = (RegIOnX-(4xRegOffX[2:0])) * RegTFallX * (255/ClkX)
16 - 31 : TFallX = 16 * (RegIOnX-(4xRegOffX[2:0])) * RegTFallX * (255/ClkX)
Software reset register
Writing consecutively 0x12 and 0x34 will reset the device (same as POR).
Always reads 0.
0xXX
0x7D
RegTFallX
RegReset
0x00
0x00
7:0
Table 9 – SX1510 Configuration Registers Description
Rev 1 – 24th Feb. 2010
26
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
5.2
SX1511 8-channel GPIO with LED Driver and Keypad Engine
Address Name
Description
Default
Device and IO Banks
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
RegInputDisable
Input buffer disable register
Output buffer long slew register
Output buffer low drive register
Pull-up register
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
1111 1111*
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
RegLongSlew
RegLowDrive
RegPullUp
RegPullDown
RegOpenDrain
RegPolarity
Pull-down register
Open drain register
Polarity register
RegDir
Direction register
RegData
Data register
RegInterruptMask
RegSenseHigh
RegSenseLow
RegInterruptSource
RegEventStatus
RegLevelShifter
RegClock
Interrupt mask register
Sense register for I/O[7:4]
Sense register for I/O[3:0]
Interrupt source register
Event status register
Level shifter register
Clock management register
Miscellaneous device settings register
LED driver enable register
RegMisc
RegLEDDriverEnable
Debounce and Keypad Engine
0x12
0x13
0x14
0x15
RegDebounceConfig
RegDebounceEnable
RegKeyConfig
Debounce configuration register
Debounce enable register
Key scan configuration register
Key value
0000 0000
0000 0000
0000 0000
1111 1111
RegKeyData
LED Driver (PWM, blinking, breathing)
0x16
0x17
RegIOn0
RegIOn1
RegTOn2
RegIOn2
RegOff2
ON intensity register for I/O[0]
ON intensity register for I/O[1]
ON time register for I/O[2]
1111 1111
1111 1111
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
1111 1111
1111 1111
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0x18
0x19
ON intensity register for I/O[2]
OFF time/intensity register for I/O[2]
ON time register for I/O[3]
0x1A
0x1B
RegTOn3
RegIOn3
RegOff3
0x1C
ON intensity register for I/O[3]
OFF time/intensity register for I/O[3]
Fade in register for I/O[3]
0x1D
0x1E
RegTRise3
RegTFall3
RegIOn4
RegIOn5
RegTOn6
RegIOn6
RegOff6
0x1F
Fade out register for I/O[3]
0x20
ON intensity register for I/O[4]
ON intensity register for I/O[5]
ON time register for I/O[6]
0x21
0x22
0x23
ON intensity register for I/O[6]
OFF time/intensity register for I/O[6]
ON time register for I/O[7]
0x24
0x25
RegTOn7
RegIOn7
RegOff7
0x26
ON intensity register for I/O[7]
OFF time/intensity register for I/O[7]
Fade in register for I/O[7]
0x27
0x28
RegTRise7
RegTFall7
0x29
Fade out register for I/O[7]
Miscellaneous
0x2A
RegHighInput
RegReset
High input enable register
Software reset register
0000 0000
0000 0000
Software Reset
0x7D
Test (not to be written)
0x7E
0x7F
RegTest1
RegTest2
Test register
Test register
0000 0000
0000 0000
*Bits set as output take “1” as default value.
Table 10 – SX1511 Configuration Registers Overview
Rev 1 – 24th Feb. 2010
27
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Addr Name
Default Bits Description
Disables the input buffer of each [input-configured] IO
0x00
0x01
0x02
0x03
0x04
0x05
0x06
RegInputDisable
0x00
0x00
0x00
0x00
0x00
0x00
0x00
7:0
7:0
7:0
7:0
7:0
7:0
7:0
0 : Input buffer is enabled (input actually being used)
1 : Input buffer is disabled (input actually not being used or LED connection)
Enables increased slew rate of the output buffer of each [output-configured] IO
0 : Increased slew rate is disabled
1 : Increased slew rate is enabled
Enables reduced drive of the output buffer of each [output-configured] IO
0 : Reduced drive is disabled
1 : Reduced drive is enabled
Enables the pull-up for each IO
0 : Pull-up is disabled
1 : Pull-up is enabled
Enables the pull-down for each IO
0 : Pull-down is disabled
1 : Pull-down is enabled
Enables open drain operation for each [output-configured] IO
0 : Regular push-pull operation
1 : Open drain operation
RegLongSlew
RegLowDrive
RegPullUp
RegPullDown
RegOpenDrain
RegPolarity
Enables polarity inversion for each IO
0 : Normal polarity : RegData[x] = IO[x]
1 : Inverted polarity : RegData[x] = !IO[x] (for both input and output configured IOs)
Configures direction for each IO.
0 : IO is configured as an output
1 : IO is configured as an input
Write: Data to be output to the output-configured IOs
Read: Data seen at the IOs, independent of the direction configured.
0x07
0x08
0x09
RegDir
0xFF
0xFF
0xFF
7:0
7:0
7:0
RegData
Configures which [input-configured] IO will trigger an interrupt on NINT pin
0 : An event on this IO will trigger an interrupt
RegInterruptMask
1 : An event on this IO will NOT trigger an interrupt
7:6
5:4
3:2
1:0
7:6
5:4
3:2
1:0
Edge sensitivity of RegData[7]
Edge sensitivity of RegData[6]
Edge sensitivity of RegData[5]
Edge sensitivity of RegData[4]
Edge sensitivity of RegData[3]
Edge sensitivity of RegData[2]
Edge sensitivity of RegData[1]
Edge sensitivity of RegData[0]
00 : None
01 : Rising
10 : Falling
11 : Both
0x0A
0x0B
RegSenseHigh
RegSenseLow
0x00
0x00
00 : None
01 : Rising
10 : Falling
11 : Both
Interrupt source (from IOs set in RegInterruptMask)
0 : No interrupt has been triggered by this IO
1 : An interrupt has been triggered by this IO (an event as configured in relevant
RegSense register occured).
0x0C
RegInterruptSource
0x00
7:0
7:0
Writing '1' clears the bit in RegInterruptSource and in RegEventStatus
When all bits are cleared, NINT signal goes back high.
Event status of all IOs.
0 : No event has occured on this IO
1 : An event has occured on this IO (an edge as configured in relevant RegSense
register occured).
0x0D
0x0E
RegEventStatus
RegLevelShifter
0x00
0x00
Writing '1' clears the bit in RegEventStatus and in RegInterruptSource if relevant.
If the edge sensitivity of the IO is changed, the bit(s) will be cleared automatically
7:6
5:4
3:2
1:0
7
Level shifter mode for IO[3] (Bank A) and IO[7] (Bank B)
Level shifter mode for IO[2] (Bank A) and IO[6] (Bank B)
Level shifter mode for IO[1] (Bank A) and IO[5] (Bank B)
Level shifter mode for IO[0] (Bank A) and IO[4] (Bank B)
Unused
00 : OFF
01 : A->B
10 : B->A
11 : Reserved
Oscillator frequency (fOSC) source
00 : OFF. LED driver, keypad engine and debounce features are disabled.
01 : External clock input (OSCIN)
6:5
10 : Internal 2MHz oscillator
11 : Reserved
OSCIO pin function (Cf. §4.8)
0 : OSCIO is an input (OSCIN)
1 : OSCIO is an output (OSCOUT)
Frequency of the signal output on OSCOUT pin:
0x0 : 0Hz, permanent "0" logical level (GPO)
0xF : 0Hz, permanent "1" logical level (GPO)
Else : fOSCOUT = fOSC/(2^(RegClock[3:0]-1))
LED Driver mode for Bank B’s fading capable IOs (IO7)
0: Linear
0x0F
0x10
RegClock
RegMisc
0x00
0x00
4
3:0
7
1: Logarithmic
Rev 1 – 24th Feb. 2010
28
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Frequency of the LED Driver clock ClkX of all IOs:
0 : OFF. LED driver functionality is disabled for all IOs.
Else : ClkX = fOSC/(2^(RegMisc[6:4]-1))
LED Driver mode for Bank A’s fading capable IOs (IO3)
0: Linear
6:4
3
1: Logarithmic
NRESET pin function when externally forced low (Cf. §4.4.1 and §4.9.5)
0: Equivalent to POR
1: Reset PWM/Blink/Fade counters (not user programmed values)
This bit can only be reset manually or by POR, not by NRESET.
Auto-increment register address (Cf. §4.5)
0: ON. When several consecutive data are read/written, register address is incremented.
1: OFF. When several consecutive data are read/written, register address is kept fixed.
Autoclear NINT on RegData read (Cf. §4.7)
0: ON. RegInterruptSource is also automatically cleared when RegData is read.
1: OFF. RegInterruptSource must be manually cleared, either directly or via
RegEventStatus.
2
1
0
Enables LED Driver for each [output-configured] IO
0 : LED Driver is disabled
1 : LED Driver is enabled
0x11
0x12
RegLEDDriverEnable
RegDebounceConfig
0x00
0x00
7:0
7:3
Unused
Debounce time (Cf. §4.6.1)
000: 0.5ms x 2MHz/fOSC
001: 1ms x 2MHz/fOSC
010: 2ms x 2MHz/fOSC
011: 4ms x 2MHz/fOSC
100: 8ms x 2MHz/fOSC
101: 16ms x 2MHz/fOSC
110: 32ms x 2MHz/fOSC
111: 64ms x 2MHz/fOSC
2:0
Enables debouncing for each [input-configured] IO
0 : Debouncing is disabled
1 : Debouncing is enabled
0x13
RegDebounceEnable
0x00
7:0
7
Unused
Number of rows (outputs) + key scan enable
00 : Key scan OFF
6:5
4:3
01 : 2 rows – IO[0:1]
10 : 3 rows – IO[0:2]
11 : 4 rows – IO[0:3]
Number of columns (inputs)
00 : 1 column – IO[4]
01 : 2 columns – IO[4:5]
10 : 3 columns – IO[4:6]
11 : 4 columns – IO[4:7]
Scan time per row (must be set above debounce time).
000 : 1ms x 2MHz/fOSC
001 : 2ms x 2MHz/fOSC
010 : 4ms x 2MHz/fOSC
011 : 8ms x 2MHz/fOSC
100 : 16ms x 2MHz/fOSC
101 : 32ms x 2MHz/fOSC
110 : 64ms x 2MHz/fOSC
111 : 128ms x 2MHz/fOSC
0x14
RegKeyConfig
0x00
2:0
Key which generated NINT (active low)
0x15
0xXX
RegKeyData
RegTOnX
0xFF
0x00
7:0
7:5
Ex: RegKeyData=11011110 => key [IO5;IO0] has been pressed and generated NINT
When read it is automatically cleared together with NINT and key scan continues.
Unused
ON Time of IO[X]:
0 : Infinite (Static mode, TOn directly controlled by RegData, Cf §4.9.2)
1 - 15 : TOnX = 64 * RegTOnX * (255/ClkX)
16 - 31 : TOnX = 512 * RegTOnX * (255/ClkX)
ON Intensity of IO[X]
- Linear mode : IOnX = RegIOnX
- Logarithmic mode (fading capable IOs only) : IOnX = f(RegIOnX) , Cf §4.9.5
OFF Time of IO[X]:
0 : Infinite (Single shot mode, TOff directly controlled by RegData, Cf §4.9.3)
1 - 15 : TOffX = 64 * RegOffX[7:3] * (255/ClkX)
16 - 31 : TOffX = 512 * RegOffX[7:3] * (255/ClkX)
OFF Intensity of IO[X]
4:0
7:0
7:3
0xXX
0xXX
RegIOnX
RegOffX
0xFF
0x00
2:0
7:5
- Linear mode : IOffX = 4 x RegOff[2:0]
- Logarithmic mode (fading capable IOs only) : IOffX = f(4 x RegOffX[2:0]) , Cf §4.9.5
Unused
Fade In setting of IO[X]
0 : OFF
1 - 15 : TRiseX = (RegIOnX-(4xRegOffX[2:0])) * RegTRiseX * (255/ClkX)
16 - 31 : TRiseX = 16 * (RegIOnX-(4xRegOffX[2:0])) * RegTRiseX * (255/ClkX)
0xXX
RegTRiseX
0x00
4:0
Rev 1 – 24th Feb. 2010
29
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
7:5
Unused
Fade Out setting of IO[X]
0 : OFF
1 - 15 : TFallX = (RegIOnX-(4xRegOffX[2:0])) * RegTFallX * (255/ClkX)
16 - 31 : TFallX = 16 * (RegIOnX-(4xRegOffX[2:0])) * RegTFallX * (255/ClkX)
0xXX
RegTFallX
0x00
4:0
Enables high input mode for each [input-configured] IO
0 : OFF. VIH max = 3.6V and VCCx min = 1.2V
1 : ON. VIH max = 5.5V and VCCx min = 1.65V
Software reset register
Writing consecutively 0x12 and 0x34 will reset the device (same as POR)
Always reads 0.
0x2A
0x7D
RegHighInput
RegReset
0x00
0x00
7:0
7:0
Table 11 – SX1511 Configuration Registers Description
Rev 1 – 24th Feb. 2010
30
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
5.1
SX1512 16-channel GPIO with LED Driver and Keypad Engine
Address Name
Description
Default
Device and IO Banks
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
0x21
RegInputDisableB
Input buffer disable register - I/O[15-8] (Bank B)
Input buffer disable register - I/O[7-0] (Bank A)
Output buffer long slew register - I/O[15-8] (Bank B)
Output buffer long slew register - I/O[7-0] (Bank A)
Output buffer low drive register - I/O[15-8] (Bank B)
Output buffer low drive register - I/O[7-0] (Bank A)
Pull-up register - I/O[15-8] (Bank B)
Pull-up register - I/O[7-0] (Bank A)
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
1111 1111
1111 1111*
1111 1111*
1111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
RegInputDisableA
RegLongSlewB
RegLongSlewA
RegLowDriveB
RegLowDriveA
RegPullUpB
RegPullUpA
RegPullDownB
RegPullDownA
RegOpenDrainB
RegOpenDrainA
RegPolarityB
Pull-down register - I/O[15-8] (Bank B)
Pull-down register - I/O[7-0] (Bank A)
Open drain register - I/O[15-8] (Bank B)
Open drain register - I/O[7-0] (Bank A)
Polarity register - I/O[15-8] (Bank B)
Polarity register - I/O[7-0] (Bank A)
Direction register - I/O[15-8] (Bank B)
Direction register - I/O[7-0] (Bank A)
Data register - I/O[15-8] (Bank B)
RegPolarityA
RegDirB
RegDirA
RegDataB
RegDataA
Data register - I/O[7-0] (Bank A)
RegInterruptMaskB
RegInterruptMaskA
RegSenseHighB
RegSenseLowB
RegSenseHighA
RegSenseLowA
RegInterruptSourceB
RegInterruptSourceA
RegEventStatusB
RegEventStatusA
RegLevelShifter1
RegLevelShifter2
RegClock
Interrupt mask register - I/O[15-8] (Bank B)
Interrupt mask register - I/O[7-0] (Bank A)
Sense register for I/O[15:12]
Sense register for I/O[11:8]
Sense register for I/O[7:4]
Sense register for I/O[3:0]
Interrupt source register - I/O[15-8] (Bank B)
Interrupt source register - I/O[7-0] (Bank A)
Event status register - I/O[15-8] (Bank B)
Event status register - I/O[7-0] (Bank A)
Level shifter register
Level shifter register
Clock management register
RegMisc
Miscellaneous device settings register
LED driver enable register - I/O[15-8] (Bank B)
LED driver enable register - I/O[7-0] (Bank A)
RegLEDDriverEnableB
RegLEDDriverEnableA
Debounce and Keypad Engine
0x22
0x23
0x24
0x25
0x26
0x27
0x28
RegDebounceConfig
RegDebounceEnableB
RegDebounceEnableA
RegKeyConfig1
Debounce configuration register
Debounce enable register - I/O[15-8] (Bank B)
Debounce enable register - I/O[7-0] (Bank A)
Key scan configuration register
Key scan configuration register
Key value (column)
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
1111 1111
RegKeyConfig2
RegKeyData1
RegKeyData2
Key value (row)
LED Driver (PWM, blinking, breathing)
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
0x30
0x31
0x32
0x33
0x34
0x35
0x36
0x37
RegTOn0
RegIOn0
RegOff0
RegTOn1
RegIOn1
RegOff1
RegTOn2
RegIOn2
RegOff2
RegTOn3
RegIOn3
RegOff3
RegTOn4
RegIOn4
RegOff4
ON time register for I/O[0]
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
ON intensity register for I/O[0]
OFF time/intensity register for I/O[0]
ON time register for I/O[1]
ON intensity register for I/O[1]
OFF time/intensity register for I/O[1]
ON time register for I/O[2]
ON intensity register for I/O[2]
OFF time/intensity register for I/O[2]
ON time register for I/O[3]
ON intensity register for I/O[3]
OFF time/intensity register for I/O[3]
ON time register for I/O[4]
ON intensity register for I/O[4]
OFF time/intensity register for I/O[4]
Rev 1 – 24th Feb. 2010
31
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Address Name
Description
Default
0000 0000
0000 0000
0000 0000
0x38
RegTRise4
Fade in register for I/O[4]
Fade out register for I/O[4]
ON time register for I/O[5]
0x39
RegTFall4
RegTOn5
RegIOn5
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
0x40
ON intensity register for I/O[5]
OFF time/intensity register for I/O[5]
Fade in register for I/O[5]
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
1111 1111
0000 0000
0000 0000
0000 0000
RegOff5
RegTRise5
RegTFall5
RegTOn6
RegIOn6
Fade out register for I/O[5]
ON time register for I/O[6]
ON intensity register for I/O[6]
OFF time/intensity register for I/O[6]
Fade in register for I/O[6]
0x41
RegOff6
0x42
RegTRise6
RegTFall6
RegTOn7
RegIOn7
0x43
Fade out register for I/O[6]
0x44
ON time register for I/O[7]
0x45
ON intensity register for I/O[7]
OFF time/intensity register for I/O[7]
Fade in register for I/O[7]
0x46
RegOff7
0x47
RegTRise7
RegTFall7
RegTOn8
RegIOn8
0x48
Fade out register for I/O[7]
0x49
ON time register for I/O[8]
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
0x50
ON intensity register for I/O[8]
OFF time/intensity register for I/O[8]
ON time register for I/O[9]
RegOff8
RegTOn9
RegIOn9
ON intensity register for I/O[9]
OFF time/intensity register for I/O[9]
ON time register for I/O[10]
RegOff9
RegTOn10
RegIOn10
RegOff10
RegTOn11
RegIOn11
RegOff11
RegTOn12
RegIOn12
RegOff12
RegTRise12
RegTFall12
RegTOn13
RegIOn13
RegOff13
RegTRise13
RegTFall13
RegTOn14
RegIOn14
RegOff14
RegTRise14
RegTFall14
RegTOn15
RegIOn15
RegOff15
RegTRise15
RegTFall15
ON intensity register for I/O[10]
OFF time/intensity register for I/O[10]
ON time register for I/O[11]
0x51
0x52
0x53
ON intensity register for I/O[11]
OFF time/intensity register for I/O[11]
ON time register for I/O[12]
0x54
0x55
0x56
ON intensity register for I/O[12]
OFF time/intensity register for I/O[12]
Fade in register for I/O[12]
0x57
0x58
0x59
Fade out register for I/O[12]
ON time register for I/O[13]
0x5A
0x5B
0x5C
0x5D
0x5E
0x5F
0x60
ON intensity register for I/O[13]
OFF time/intensity register for I/O[13]
Fade in register for I/O[13]
Fade out register for I/O[13]
ON time register for I/O[14]
ON intensity register for I/O[14]
OFF time/intensity register for I/O[14]
Fade in register for I/O[14]
0x61
0x62
0x63
Fade out register for I/O[14]
ON time register for I/O[15]
0x64
0x65
ON intensity register for I/O[15]
OFF time/intensity register for I/O[15]
Fade in register for I/O[15]
0x66
0x67
0x68
Fade out register for I/O[15]
Miscellaneous
0x69
RegHighInputB
RegHighInputA
High input enable register - I/O[15-8] (Bank B)
High input enable register - I/O[7-0] (Bank A)
0000 0000
0000 0000
0x6A
Software Reset
0x7D
RegReset
Software reset register
0000 0000
Test (not to be written)
0x7E
0x7F
RegTest1
RegTest2
Test register
Test register
0000 0000
0000 0000
*Bits set as output take “1” as default value.
Table 12 – SX1512 Configuration Registers Overview
Rev 1 – 24th Feb. 2010
32
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Addr Name
Default Bits Description
Disables the input buffer of each IO
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
RegInputDisableB
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0xFF
0xFF
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
7:0
0 : Input buffer is enabled (input actually being used)
1 : Input buffer is disabled (input actually not being used or LED connection)
Disables the input buffer of each IO
0 : Input buffer is enabled (input actually being used)
1 : Input buffer is disabled (input actually not being used, LED connection)
Enables increased slew rate of the output buffer of each [output-configured] IO
0 : Increased slew rate is disabled
1 : Increased slew rate is enabled
Enables increased slew rate of the output buffer of each [output-configured] IO
0 : Increased slew rate is disabled
1 : Increased slew rate is enabled
Enables reduced drive of the output buffer of each [output-configured] IO
0 : Reduced drive is disabled
1 : Reduced drive is enabled
Enables reduced drive of the output buffer of each [output-configured] IO
0 : Reduced drive is disabled
1 : Reduced drive is enabled
Enables the pull-up for each IO
0 : Pull-up is disabled
1 : Pull-up is enabled
Enables the pull-up for each IO
0 : Pull-up is disabled
1 : Pull-up is enabled
Enables the pull-down for each IO
0 : Pull-down is disabled
1 : Pull-down is enabled
Enables the pull-down for each IO
0 : Pull-down is disabled
1 : Pull-down is enabled
Enables open drain operation for each [output-configured] IO
0 : Regular push-pull operation
1 : Open drain operation
Enables open drain operation for each [output-configured] IO
0 : Regular push-pull operation
1 : Open drain operation
Enables polarity inversion for each IO
0 : Normal polarity : RegData[x] = IO[x]
1 : Inverted polarity : RegData[x] = !IO[x] (for both input and output configured IOs)
Enables polarity inversion for each IO
0 : Normal polarity : RegData[x] = IO[x]
1 : Inverted polarity : RegData[x] = !IO[x] (for both input and output configured IOs)
RegInputDisableA
RegLongSlewB
RegLongSlewA
RegLowDriveB
RegLowDriveA
RegPullUpB
RegPullUpA
RegPullDownB
RegPullDownA
RegOpenDrainB
RegOpenDrainA
RegPolarityB
RegPolarityA
RegDirB
Configures direction for each IO.
0 : IO is configured as an output
1 : IO is configured as an input
Configures direction for each IO.
0 : IO is configured as an output
1 : IO is configured as an input
RegDirA
Write: Data to be output to the output-configured IOs
Read: Data seen at the IOs, independent of the direction configured.
Write: Data to be output to the output-configured IOs
Read: Data seen at the IOs, independent of the direction configured.
0x10
0x11
RegDataB
RegDataA
0xFF
0xFF
7:0
7:0
Configures which [input-configured] IO will trigger an interrupt on NINT pin
0 : An event on this IO will trigger an interrupt
1 : An event on this IO will NOT trigger an interrupt
Configures which [input-configured] IO will trigger an interrupt on NINT pin
0 : An event on this IO will trigger an interrupt
0x12
0x13
RegInterruptMaskB
RegInterruptMaskA
0xFF
0xFF
7:0
7:0
1 : An event on this IO will NOT trigger an interrupt
7:6
5:4
3:2
1:0
7:6
5:4
3:2
1:0
7:6
5:4
3:2
1:0
7:6
5:4
Edge sensitivity of RegData[15]
Edge sensitivity of RegData[14]
Edge sensitivity of RegData[13]
Edge sensitivity of RegData[12]
Edge sensitivity of RegData[11]
Edge sensitivity of RegData[10]
Edge sensitivity of RegData[9]
Edge sensitivity of RegData[8]
Edge sensitivity of RegData[7]
Edge sensitivity of RegData[6]
Edge sensitivity of RegData[5]
Edge sensitivity of RegData[4]
Edge sensitivity of RegData[3]
Edge sensitivity of RegData[2]
00 : None
01 : Rising
10 : Falling
11 : Both
0x14
0x15
RegSenseHighB
RegSenseLowB
0x00
0x00
00 : None
01 : Rising
10 : Falling
11 : Both
00 : None
01 : Rising
10 : Falling
11 : Both
0x16
0x17
RegSenseHighA
RegSenseLowA
0x00
0x00
00 : None
01 : Rising
Rev 1 – 24th Feb. 2010
33
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
3:2
1:0
Edge sensitivity of RegData[1]
Edge sensitivity of RegData[0]
Interrupt source (from IOs set in RegInterruptMask)
0 : No interrupt has been triggered by this IO
1 : An interrupt has been triggered by this IO (an event as configured in relevant
RegSense register occured).
0x18
0x19
0x1A
0x1B
RegInterruptSourceB
RegInterruptSourceA
RegEventStatusB
0x00
0x00
0x00
0x00
7:0
7:0
7:0
7:0
Writing '1' clears the bit in RegInterruptSource and in RegEventStatus
When all bits are cleared, NINT signal goes back high.
Interrupt source (from IOs set in RegInterruptMask)
0 : No interrupt has been triggered by this IO
1 : An interrupt has been triggered by this IO (an event as configured in relevant
RegSense register occured).
Writing '1' clears the bit in RegInterruptSource and in RegEventStatus
When all bits are cleared, NINT signal goes back high.
Event status of all IOs.
0 : No event has occured on this IO
1 : An event has occured on this IO (an edge as configured in relevant RegSense
register occured).
Writing '1' clears the bit in RegEventStatus and in RegInterruptSource if relevant.
If the edge sensitivity of the IO is changed, the bit(s) will be cleared automatically
Event status of all IOs.
0 : No event has occured on this IO
1 : An event has occured on this IO (an edge as configured in relevant RegSense
register occured).
RegEventStatusA
Writing '1' clears the bit in RegEventStatus and in RegInterruptSource if relevant.
If the edge sensitivity of the IO is changed, the bit(s) will be cleared automatically
7:6
5:4
3:2
1:0
7:6
5:4
3:2
1:0
7
Level shifter mode for IO[7] (Bank A) and IO[15] (Bank B)
Level shifter mode for IO[6] (Bank A) and IO[14] (Bank B)
Level shifter mode for IO[5] (Bank A) and IO[13] (Bank B)
Level shifter mode for IO[4] (Bank A) and IO[12] (Bank B)
Level shifter mode for IO[3] (Bank A) and IO[11] (Bank B)
Level shifter mode for IO[2] (Bank A) and IO[10] (Bank B)
Level shifter mode for IO[1] (Bank A) and IO[9] (Bank B)
Level shifter mode for IO[0] (Bank A) and IO[8] (Bank B)
Unused
00 : OFF
01 : A->B
10 : B->A
11 : Reserved
0x1C
0x1D
RegLevelShifter1
RegLevelShifter2
0x00
0x00
00 : OFF
01 : A->B
10 : B->A
11 : Reserved
Oscillator frequency (fOSC) source
00 : OFF. LED driver, keypad engine and debounce features are disabled.
01 : External clock input (OSCIN)
6:5
10 : Internal 2MHz oscillator
11 : Reserved
OSCIO pin function (Cf. §4.8)
0x1E
RegClock
0x00
4
0 : OSCIO is an input (OSCIN)
1 : OSCIO is an output (OSCOUT)
Frequency of the signal output on OSCOUT pin:
0x0 : 0Hz, permanent "0" logical level (GPO)
0xF : 0Hz, permanent "1" logical level (GPO)
Else : fOSCOUT = fOSC/(2^(RegClock[3:0]-1))
3:0
LED Driver mode for Bank B’s fading capable IOs (IO15-12)
0: Linear
1: Logarithmic
Frequency of the LED Driver clock ClkX of all IOs:
0 : OFF. LED driver functionality is disabled for all IOs.
Else : ClkX = fOSC/(2^(RegMisc[6:4]-1))
LED Driver mode for Bank A’s fading capable IOs (IO7-4)
0: Linear
7
6:4
3
1: Logarithmic
NRESET pin function when externally forced low (Cf. §4.4.1 and §4.9.5)
0: Equivalent to POR
1: Reset PWM/Blink/Fade counters (not user programmed values)
This bit is can only be reset manually or by POR, not by NRESET.
Auto-increment register address (Cf. §4.5)
0: ON. When several consecutive data are read/written, register address is incremented.
1: OFF. When several consecutive data are read/written, register address is kept fixed.
Autoclear NINT on RegData read (Cf. §4.7)
0x1F
RegMisc
0x00
2
1
0: ON. RegInterruptSourceA/B is also automatically cleared when RegDataA/B is read.
1: OFF. RegInterruptSourceA/B must be manually cleared, either directly or via
RegEventStatusA/B.
0
Enables LED Driver for each [output-configured] IO
0 : LED Driver is disabled
0x20
RegLEDDriverEnableB
0x00
7:0
1 : LED Driver is enabled
Rev 1 – 24th Feb. 2010
34
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
Enables LED Driver for each [output-configured] IO
0 : LED Driver is disabled
1 : LED Driver is enabled
0x21
RegLEDDriverEnableA
0x00
7:0
7:3
Unused
Debounce time (Cf. §4.6.1)
000: 0.5ms x 2MHz/fOSC
001: 1ms x 2MHz/fOSC
010: 2ms x 2MHz/fOSC
011: 4ms x 2MHz/fOSC
100: 8ms x 2MHz/fOSC
101: 16ms x 2MHz/fOSC
110: 32ms x 2MHz/fOSC
111: 64ms x 2MHz/fOSC
0x22
RegDebounceConfig
0x00
2:0
Enables debouncing for each [input-configured] IO
0 : Debouncing is disabled
1 : Debouncing is enabled
Enables debouncing for each [input-configured] IO
0 : Debouncing is disabled
1 : Debouncing is enabled
0x23
0x24
RegDebounceEnableB
RegDebounceEnableA
0x00
0x00
7:0
7:0
7
Reserved
Auto Sleep time (no key press within this time will set keypad engine to sleep)
000 : OFF
001 : 128ms x 2MHz/fOSC
010 : 256ms x 2MHz/fOSC
6:4
011 : 512ms x 2MHz/fOSC
100 : 1sec x 2MHz/fOSC
101 : 2sec x 2MHz/fOSC
110 : 4sec x 2MHz/fOSC
111 : 8sec x 2MHz/fOSC
Unused
0x25
RegKeyConfig1
0x00
3
Scan time per row (must be set above debounce time).
000 : 1ms x 2MHz/fOSC
001 : 2ms x 2MHz/fOSC
010 : 4ms x 2MHz/fOSC
011 : 8ms x 2MHz/fOSC
100 : 16ms x 2MHz/fOSC
101 : 32ms x 2MHz/fOSC
110 : 64ms x 2MHz/fOSC
111 : 128ms x 2MHz/fOSC
2:0
7:6
5:3
Unused
Number of rows (outputs) + key scan enable
000 : Key scan OFF
001 : 2 rows – IO[0:1]
010 : 3 rows – IO[0:2]
011 : 4 rows – IO[0:3]
100 : 5 rows – IO[0:4]
101 : 6 rows – IO[0:5]
110 : 7 rows – IO[0:6]
111 : 8 rows – IO[0:7]
0x26
RegKeyConfig2
0x00
Number of columns (inputs)
000 : 1 column – IO[8]
001 : 2 columns – IO[8:9]
010 : 3 columns – IO[8:10]
011 : 4 columns – IO[8:11]
100 : 5 columns – IO[8:12]
101 : 6 columns – IO[8:13]
110 : 7 columns – IO[8:14]
111 : 8 columns – IO[8:15]
2:0
7:0
Column which generated NINT (active low)
Ex: RegKeyData1=11011111 => IO13 has generated NINT
The register is automatically cleared when RegKeyData2 is read.
0x27
0x28
RegKeyData1
RegKeyData2
0xFF
0xFF
Row which generated NINT (active low)
Ex: RegKeyData2=11111110 => IO0 has generated NINT
When the register is read both RegKeyData1 & RegKeyData2 are automatically cleared
together with NINT and key scan continues.
Unused
ON Time of IO[X]:
0 : Infinite (Static mode, TOn directly controlled by RegData, Cf §4.9.2)
1 - 15 : TOnX = 64 * RegTOnX * (255/ClkX)
16 - 31 : TOnX = 512 * RegTOnX * (255/ClkX)
ON Intensity of IO[X]
- Linear mode : IOnX = RegIOnX
7:0
7:5
4:0
0xXX
0xXX
RegTOnX
RegIOnX
0x00
0xFF
7:0
- Logarithmic mode (fading capable IOs only) : IOnX = f(RegIOnX) , Cf §4.9.5
Rev 1 – 24th Feb. 2010
35
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
OFF Time of IO[X]:
0 : Infinite (Single shot mode, TOff directly controlled by RegData, Cf §4.9.3)
1 - 15 : TOffX = 64 * RegOffX[7:3] * (255/ClkX)
16 - 31 : TOffX = 512 * RegOffX[7:3] * (255/ClkX)
7:3
0xXX
RegOffX
0x00
OFF Intensity of IO[X]
2:0
7:5
- Linear mode : IOffX = 4 x RegOff[2:0]
- Logarithmic mode (fading capable IOs only) : IOffX = f(4 x RegOffX[2:0]) , Cf §4.9.5
Unused
Fade In setting of IO[X]
0 : OFF
1 - 15 : TRiseX = (RegIOnX-(4xRegOffX[2:0])) * RegTRiseX * (255/ClkX)
16 - 31 : TRiseX = 16 * (RegIOnX-(4xRegOffX[2:0])) * RegTRiseX * (255/ClkX)
Unused
Fade Out setting of IO[X]
0 : OFF
1 - 15 : TFallX = (RegIOnX-(4xRegOffX[2:0])) * RegTFallX * (255/ClkX)
16 - 31 : TFallX = 16 * (RegIOnX-(4xRegOffX[2:0])) * RegTFallX * (255/ClkX)
0xXX
0xXX
RegTRiseX
RegTFallX
0x00
0x00
4:0
7:5
4:0
Enables high input mode for each [input-configured] IO
0 : OFF. VIH max = 3.6V and VCCx min = 1.2V
1 : ON. VIH max = 5.5V and VCCx min = 1.65V
Enables high input mode for each [input-configured] IO
0 : OFF. VIH max = 3.6V and VCCx min = 1.2V
1 : ON. VIH max = 5.5V and VCCx min = 1.65V
Software reset register
Writing consecutively 0x12 and 0x34 will reset the device (same as POR)
Always reads 0.
0x69
0x6A
0x7D
RegHighInputB
RegHighInputA
RegReset
0x00
0x00
0x00
7:0
7:0
7:0
Table 13 – SX1512 Configuration Registers Description
Rev 1 – 24th Feb. 2010
36
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
6
APPLICATION INFORMATION
6.1
Typical Application Circuit
OSCIO
2.5V
3.3V
VCC1
I/O[0]
I/O[1]
I/O[2]
I/O[3]
VDDM
5V 5V
Host
I/O
NRESET
1.2V
SX1511
VCC2
I/O[4]
I/O[5]
NSS
SCK
SI
NSS
SCK
SI
I/O[6]
I/O[7]
SO
SO
I/O
NINT
GND
Optional (depends
on the application)
Figure 19 - Typical Application Schematic
6.2
Typical LED Connection
Typical LED Connection is described below. The LED is usually connected to a high voltage (VBAT) to take
advantage of the high sink current of the I/O and to accommodate high LED threshold voltages (VLED).
Please note that in this configuration the IO must be programmed as open drain output (RegOpenDrain) with no
pull-up (RegPullUp) and input buffer must be disabled (RegInputBufferDisable).
VCCx can take any value without compromising LED operation.
VBAT
VCCx
VLED*
VCCx
SX1510/11/12
IOx
R
IOL
*LED colour/technology dependent
Figure 20 – Typical LED Operation
Serial R must be calculated for IOL not to exceed its max spec (Cf. Table 5) else VOL will increase.
Rev 1 – 24th Feb. 2010
37
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
7
PACKAGING
INFORMATION
7.1
QFN-UT 14-pin Outline Drawing
QFN 14-pin, 2 x 2 mm, 0.4 mm pitch
Figure 21 – QFN-UT 14-pin Outline Drawing
7.2
QFN-UT 14-pin Land Pattern
Figure 22 – QFN-UT 14-pin Land Pattern
Rev 1 – 24th Feb. 2010
38
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
7.3
QFN-UT 20-pin Outline Drawing
QFN-UT 20-pin, 3 x 3 mm, 0.4 mm pitch
Figure 23 - QFN-UT 20-pin Outline Drawing
7.4
QFN-UT 20-pin Land Pattern
Figure 24 - QFN-UT 20-pin Land Pattern
Rev 1 – 24th Feb. 2010
39
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
7.5
QFN-UT 28-pin Outline Drawing
QFN-UT 28-pin, 4 x 4 mm, 0.4 mm pitch
Figure 25 - QFN-UT 28-pin Outline Drawing
7.6
QFN-UT 28-pin Land Pattern
Figure 26 - QFN-UT 28-pin Land Pattern
Rev 1 – 24th Feb. 2010
40
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
8
SOLDERING PROFILE
The soldering reflow profile for the SX1510, SX1511 and SX1512 is described in the standard IPC/JEDEC J-
STD-020C. For detailed information please go to http://www.jedec.org/download/search/jstd020c.pdf
Figure 27 - Classification Reflow Profile (IPC/JEDEC J-STD-020C)
Rev 1 – 24th Feb. 2010
41
www.semtech.com
SX1510/SX1511/SX1512
World’s Lowest Voltage Level Shifting GPIO
with LED Driver and Keypad Engine
ADVANCED COMMUNICATIONS & SENSING
© Semtech 2010
All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner. The information presented in this document does not form part of any quotation or contract, is
believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the
publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent
or other industrial or intellectual property rights. Semtech assumes no responsibility or liability whatsoever for
any failure or unexpected operation resulting from misuse, neglect improper installation, repair or improper
handling or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the
specified maximum ratings or operation outside the specified range.
SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE
SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL
APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE UNDERTAKEN SOLELY AT THE CUSTOMER’S OWN RISK. Should a customer purchase or use Semtech
products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney
fees which could arise.
Contact Information
Semtech Corporation
Advanced Communications and Sensing Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805) 498-2111 Fax: (805) 498-3804
Rev 1 – 24th Feb. 2010
42
www.semtech.com
相关型号:
SX15AD2
Peizoresistive Sensor, Absolute, 0Psi Min, 15Psi Max, -20-110mV, Rectangular, Through Hole Mount, DIP-6
HONEYWELL
SX15AD4
Peizoresistive Sensor, Absolute, 0Psi Min, 15Psi Max, -20-110mV, Rectangular, Through Hole Mount, DIP-6
HONEYWELL
SX15AHO
Peizoresistive Sensor, Absolute, 0Psi Min, 15Psi Max, -20-110mV, Round, Through Hole Mount, TO-5
HONEYWELL
SX15AN
Peizoresistive Sensor, Absolute, 0Psi Min, 15Psi Max, -20-110mV, Through Hole Mount, N HOUSING PACKAGE, 4 PIN
HONEYWELL
©2020 ICPDF网 联系我们和版权申明