PC12311YIP0FA [SHARP]
Transistor Output Optocoupler, 1-Element, 5000V Isolation,;型号: | PC12311YIP0FA |
厂家: | SHARP ELECTRIONIC COMPONENTS |
描述: | Transistor Output Optocoupler, 1-Element, 5000V Isolation, |
文件: | 总16页 (文件大小:285K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PC1231xNSZ0F Series
DIP 4pin Reinforced Insulation Type,
High CMR, Low Input Current
Photocoupler
PC1231xNSZ0F
Series
■ Description
PC1231xNSZ0F Series contains an IRED optically
coupled to a phototransistor.
■ Agency approvals/Compliance
1. Recognized by UL1577 (Double protection isolation),
file No. E64380 (as model No. PC1231)
It is packaged in a 4-pin DIP, available in wide-lead
spacing option and SMT gullwing lead-form option.
Input-output isolation voltage(rms) is 5.0kV.
CTR is 50% to 400% at input current of 0.5mA.
2. Approved by BSI, BS-EN60065, file No. 7087, BS-
EN60950, file No. 7409, (as model No. PC1231)
3. Approved by SEMCO, EN60065, EN60950, file No.
9933036 (as model No. PC1231)
4. Approved by DEMCO, EN60065, EN60950, file No.
99-03814 (as model No. PC1231)
5. Approved by NEMKO, EN60065, EN60950, file No.
P99102251 (as model No. PC1231)
6. Approved by FIMKO, EN60065, EN60950, file No.
13986 (as model No. PC1231)
■ Features
1. 4pin DIP package
2. Double transfer mold package (Ideal for Flow Solder-
ing)
3. Low input current type (IF=0.5mA)
4. High resistance to noise due to high common rejec-
tion voltage (CMR : MIN. 10kV/ s)
5. Reinforced insulation type (Isolation distance : MIN.
0.4mm)
7. Recognized by CSA file No. CA095323 (as model
No. PC1231)
8. Approved by VDE, DIN EN60747-5-2( ) (as an op-
tion), file No. 40008087(as model No. PC1231)
9. Package resin : UL flammability grade (94V-0)
6. Long creepage distance type (wide lead-form type
only : MIN. 8mm)
( )DIN EN60747-5-2 : successor standard of DIN VDE0884
7. High isolation voltage between input and output
(Viso(rms) : 5.0kV)
8. Lead-free and RoHS directive compliant
■ Applications
1. Primary to secondary isolation in switch mode power
supply
2. Noise suppression in switching circuit
3. Signal transmission between circuits of different po-
tentials and impedances
4. Over voltage detection
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: D2-A02903EN
1
Date Jun. 30. 2005
© SHARP Corporation
PC1231xNSZ0F Series
■ Internal Connection Diagram
1
2
3
4
Anode
1
4
3
Cathode
Emitter
Collector
2
(Unit : mm)
■ Outline Dimensions
1. Through-Hole [ex. PC1231xNSZ0F]
2. Through-Hole (VDE option) [ex. PC1231xYSZ0F]
Rank mark
Anode mark
Rank mark
Anode mark
Factory identification mark
Factory identification mark
Date code
Date code
1
2
4
3
1
2
4
3
1 2 3 1
1 2 3 1
4
SHARP mark "S"
6.5±0.3
VDE
Indenfication mark
6.5±0.3
7.62±0.3
4.58±0.3
7.62±0.3
4.58±0.3
Epoxy resin
0.26±0.1
Epoxy resin
0.26±0.1
0.5±0.1
0.5±0.1
θ
θ
θ
θ
θ : 0 to 13˚
θ : 0 to 13˚
Product mass : approx. 0.23g
Product mass : approx. 0.23g
3. Wide Through-Hole Lead-Form [ex. PC1231xNFZ0F]
4. Wide Through-Hole Lead-Form (VDE option)
[ex. PC1231xYFZ0F]
Factory identification mark
Rank mark
Factory identification mark
Rank mark
Anode mark
Anode mark
Date code
Date code
1
2
1
2
4
3
4
3
1 2 3 1
1 2 3 1
4
SHARP mark "S"
6.5±0.3
6.5±0.3
VDE
Indenfication mark
7.62±0.3
4.58±0.3
7.62±0.3
4.58±0.3
Epoxy resin
10.16±0.5
Epoxy resin
10.16±0.5
0.26±0.1
0.26±0.1
0.5±0.1
0.5±0.1
Product mass : approx. 0.23g
Product mass : approx. 0.23g
Sheet No.: D2-A02903EN
2
PC1231xNSZ0F Series
(Unit : mm)
5. SMT Gullwing Lead-Form [ex. PC1231xNIP0F]
6. SMT Gullwing Lead-Form (VDE option)
[ex. PC1231xYIP0F]
Rank mark
Anode mark
Factory identification mark
Rank mark
Anode mark
Factory identification mark
Date code
Date code
4
1
4
1
2
3
2
3
1 2 3 1
1 2 3 1
4
SHARP mark "S"
6.5±0.3
6.5±0.3
VDE
Indenfication mark
7.62±0.3
4.58±0.3
7.62±0.3
4.58±0.3
2.54±0.25
2.54±0.25
+0.4
+0.4
+0.4
+0.4
Epoxy resin
Epoxy resin
1.0
−0
1.0
1.0
−0
1.0
−0
−0
+0
+0
10.0
10.0
−0.5
−0.5
Product mass : approx. 0.22g
Product mass : approx. 0.22g
7. Wide SMT Gullwing Lead-Form [ex. PC1231xNUP0F]
8. Wide SMT Gullwing Lead-Form (VDE option)
[ex. PC1231xYUP0F]
Rank mark
Rank mark
Anode mark
Factory identification mark
Anode mark
Factory identification mark
Date code
Date code
1
2
4
1
2
4
3
3
1 2 3 1
1 2 3 1
4
6.5±0.3
6.5±0.3
VDE
Indenfication mark
4.58±0.3
SHARP mark "S"
7.62±0.3
7.62±0.3
4.58±0.3
Epoxy resin
0.5±0.1
0.75±0.25
10.16±0.5
12.0MAX
0.75±0.25
Epoxy resin
10.16±0.5
12.0MAX
0.5±0.1
0.75±0.25
0.75±0.25
Product mass : approx. 0.22g
Product mass : approx. 0.22g
Plating material : SnCu (Cu : TYP. 2%)
Sheet No.: D2-A02903EN
3
PC1231xNSZ0F Series
Date code (2 digit)
1st digit
2nd digit
Year of production
Month of production
A.D.
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
A.D
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
Mark
P
Month
Mark
1
Mark
A
B
January
February
March
R
2
S
3
C
T
April
4
D
E
U
May
5
F
V
June
6
H
J
W
X
July
7
August
September
October
November
December
8
K
L
A
9
B
O
N
D
M
N
C
·
·
·
·
·
·
repeats in a 20 year cycle
Factory identification mark
Factory identification Mark
Country of origin
no mark
Japan
Indonesia
China
* This factory marking is for identification purpose only.
Please contact the local SHARP sales representative to see the actual status of the
production.
Rank mark
Refer to the Model Line-up table
Sheet No.: D2-A02903EN
4
PC1231xNSZ0F Series
■ Absolute Maximum Ratings
(Ta=25˚C)
Unit
mA
mA
V
Parameter
Symbol
IF
Rating
Forward current
10
*1 Peak forward current
Reverse voltage
IFM
200
VR
6
Power dissipation
P
15
mW
V
Collector-emitter voltage
Emitter-collector voltage
Collector current
VCEO
VECO
IC
70
6
50
V
mA
mW
mW
kV
Collector power dissipation
Total power dissipation
*2 Isolation voltage
Operating temperature
Storage temperature
*3 Soldering temperature
PC
150
Ptot
170
Viso (rms)
Topr
Tstg
Tsol
5.0
−30 to +100
−55 to +125
260
˚C
˚C
˚C
*1 Pulse width≤100µs, Duty ratio : 0.001
*2 40 to 60%RH, AC for 1 minute, f=60Hz
*3 For 10s
■ Electro-optical Characteristics
(Ta=25˚C)
Parameter
Forward voltage
Symbol
VF
Conditions
MIN.
TYP.
MAX.
1.4
10
Unit
V
IF=10mA
VR=4V
−
1.2
Input Reverse current
Terminal capacitance
Collector dark current
IR
−
−
µA
pF
nA
V
Ct
V=0, f=1kHz
−
30
250
100
−
ICEO
VCE=50V, IF=0
IC=0.1mA, IF=0
IE=10µA, IF=0
IF=0.5mA, VCE=5V
IF=10mA, IC=1mA
DC500V, 40 to 60%RH
V=0, f=1MHz
−
−
Output Collector-emitter breakdown voltage BVCEO
70
−
Emitter-collector breakdown voltage
BVECO
IC
6
−
−
V
Collector current
0.25
−
2.0
0.2
−
mA
V
Collector-emitter saturation voltage VCE (sat)
−
−
1×1011
0.6
4
Isolation resistance
Floating capacitance
RISO
Cf
tr
5×1010
Ω
Transfer
charac-
teristics
−
−
−
1.0
18
pF
µs
µs
Rise time
Response time
VCE=2V, IC=2mA, RL=100Ω
Fall time
tf
3
18
Common mode
rejection voltage
VCM=1.5kV(peak), IF=0
RL=470Ω, VCC=9V, Vnp=100mV
CMR
10
−
−
kV/µs
Sheet No.: D2-A02903EN
5
PC1231xNSZ0F Series
■ Model Line-up
Lead Form
Trough-Hole
Wide Trough-Hole
IC [mA]
Rank mark
Sleeve
100pcs/sleeve
(I =0.5mA, V =5V, T =25˚C)
Package
F
CE
a
DIN EN60747-5-2
Approved
Approved
0.25 to 2.0
0.5 to 1.25
PC12310NSZ0F PC12310YSZ0F PC12310NFZ0F PC12310YFZ0F with or without
Model No.
PC12311NSZ0F PC12311YSZ0F PC12311NFZ0F PC12311YFZ0F
SMT Gullwing Wide SMT Gullwing
A
Lead Form
Package
IC [mA]
Rank mark
Taping
(I =0.5mA, V =5V, T =25˚C)
F
CE
a
2 000pcs/reel
DIN EN60747-5-2
Approved
PC12310NIP0F PC12310YIP0F PC12310NUP0F PC12310YUP0F with or without
PC12311NIP0F PC12311YIP0F PC12311NUP0F PC12311YUP0F
Please contact a local SHARP sales representative to inquire about production status.
Approved
0.25 to 2.0
0.5 to 1.25
Model No.
A
Sheet No.: D2-A02903EN
6
PC1231xNSZ0F Series
Fig.1 Test Circuit for Common Mode Rejection Voltage
(dV/dt)
VCM
1)
VCC
Vnp
Vcp
RL
Vnp
VO
VCM : High wave
pulse
RL=470Ω
(Vcp Nearly = dV/dt×Cf×RL)
1) Vcp : Voltage which is generated by displacement current in floating
capacitance between primary and secondary side.
VCM
VCC=9V
Fig.2 Forward Current vs. Ambient
Fig.3 Diode Power Dissipation vs. Ambient
Temperature
Temperature
15
15
10
10
5
0
5
0
−30
0
25
50
75
100
125
−30
0
25
50
75
100
125
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Fig.4 Collector Power Dissipation vs.
Fig.5 Total Power Dissipation vs. Ambient
Ambient Temperature
250
Temperature
250
200
200
150
100
170
150
100
50
0
50
0
−30
0
25
50
75
100
125
−30
0
25
50
75
100
125
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Sheet No.: D2-A02903EN
7
PC1231xNSZ0F Series
Fig.6 Peak Forward Current vs. Duty Ratio
Fig.7 Forward Current vs. Forward Voltage
1 000
100
Pulse width≤100µs
Ta=25˚C
10
100
Ta=25˚C
Ta=100˚C
Ta=0˚C
Ta=75˚C
Ta=50˚C
1
Ta=−25˚C
10
0.1
10−3
10−2
Duty ratio
10−1
1
0
0.5
1
1.5
2
Forward voltage VF (V)
Fig.8 Current Transfer Ratio vs. Forward
Current
Fig.9 Collector Current vs. Collector-emitter
Voltage
500
40
VCE=5V
Ta=25˚C
Ta=25˚C
PC (MAX.)
400
300
200
30
IF=7mA
20
IF=5mA
IF=3mA
10
IF=2mA
100
0
IF=1mA
IF=0.5mA
0
0.1
1
10
0
2
4
6
8
10
Forward current IF (mA)
Collector-emitter voltage VCE (V)
Fig.10 Relative Current Transfer Ratio vs.
Fig.11 Collector - emitter Saturation Voltage
vs. Ambient Temperature
Ambient Temperature
150
0.16
IF=10mA
IC=1mA
0.14
VCE=5V
IF=0.5mA
0.12
0.1
100
0.08
0.06
0.04
50
0
0.02
0
−30 −20 −10
0
10 20 30 40 50 60 70 80 90 100
−30 −20 −10
0
10 20 30 40 50 60 70 80 90 100
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Sheet No.: D2-A02903EN
8
PC1231xNSZ0F Series
Fig.12 Collector Dark Current vs. Ambient
Temperature
Fig.13 Response Time vs. Load Resistance
10−5
100
V
CE=2V, IC=2mA
VCE=50V
10−6
10−7
10−8
10−9
tr
tf
10
td
ts
10−10
10−11
1
0.1
1
10
−30 −20 −10
0
10 20 30 40 50 60 70 80 90 100
Ambient temperature Ta (˚C)
Load resistance RL (kΩ)
Fig.14 Test Circuit for Response Time
Fig.15 Frequency Response
5
0
VCC
VCE=2V
IC=2mA
Ta=25˚C
RL
RD
Input
Input
Output
VCE
Output
RL=10kΩ
−5
10%
90%
1kΩ
ts
tf
td
tr
−10
−15
100Ω
Please refer to the conditions in Fig.13.
−20
−25
0.1
1
10
100
1 000
Frequency f (kHz)
Fig.16 Collector-emitter Saturation Voltage
vs. Forward Current
5
IC=7mA
Ta=25˚C
IC=5mA
4
IC=3mA
IC=2mA
3
IC=1mA
IC=0.5mA
2
1
0
0
2
4
6
8
10
Forward current IF (mA)
Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.
9
Sheet No.: D2-A02903EN
PC1231xNSZ0F Series
■ Design Considerations
● Design guide
While operating at IF<0.5mA, CTR variation may increase.
Please make design considering this fact.
In case that some sudden big noise caused by voltage variation is provided between primary and secondary
terminals of photocoupler some current caused by it is floating capacitance may be generated and result in
false operation since current may go through IRED or current may change.
If the photocoupler may be used under the circumstances where noise will be generated we recommend to
use the bypass capacitors at the both ends of IRED.
This product is not designed against irradiation and incorporates non-coherent IRED.
● Degradation
In general, the emission of the IRED used in photocouplers will degrade over time.
In the case of long term operation, please take the general IRED degradation (50% degradation over 5
years) into the design consideration.
● Recommended Foot Print (reference)
SMT Gullwing lead-form
Wide SMT Gullwing lead-form
8.2
10.2
2.2
2.2
(Unit : mm)
✩
For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: D2-A02903EN
10
PC1231xNSZ0F Series
■ Manufacturing Guidelines
● Soldering Method
Reflow Soldering:
Reflow soldering should follow the temperature profile shown below.
Soldering should not exceed the curve of temperature profile and time.
Please don't solder more than twice.
(˚C)
300
Terminal : 260˚C peak
( package surface : 250˚C peak)
200
Reflow
220˚C or more, 60s or less
Preheat
100
150 to 180˚C, 120s or less
0
0
1
2
3
4
(min)
Flow Soldering :
Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below
listed guidelines.
Flow soldering should be completed below 270˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please don't solder more than twice.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400˚C.
Please don't solder more than twice.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
Sheet No.: D2-A02903EN
11
PC1231xNSZ0F Series
● Cleaning instructions
Solvent cleaning:
Solvent temperature should be 45˚C or below Immersion time should be 3 minutes or less
Ultrasonic cleaning:
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials:
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol
In case the other type of solvent materials are intended to be used, please make sure they work fine in ac-
tual using conditions since some materials may erode the packaging resin.
● Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this product.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC).
•Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated di-
phenyl ethers (PBDE).
Sheet No.: D2-A02903EN
12
PC1231xNSZ0F Series
■ Package specification
● Sleeve package
1. Through-Hole
Package materials
Sleeve : HIPS (with anti-static material)
Stopper : Styrene-Elastomer
Package method
MAX. 100pcs of products shall be packaged in a sleeve. Both ends shall be closed by tabbed and tabless stoppers.
The product shall be arranged in the sleeve with its anode mark on the tabless stopper side.
MAX. 20 sleeves in one case.
Sleeve outline dimensions
12.0
6.7
(Unit : mm)
2. Wide Through-Hole
Package materials
Sleeve : HIPS (with anti-static material)
Stopper : Styrene-Elastomer
Package method
MAX. 100pcs of products shall be packaged in a sleeve. Both ends shall be closed by tabbed and tabless stoppers.
The product shall be arranged in the sleeve with its anode mark on the tabless stopper side.
MAX. 20 sleeves in one case.
Sleeve outline dimensions
15.0
6.35
(Unit : mm)
Sheet No.: D2-A02903EN
13
PC1231xNSZ0F Series
● Tape and Reel package
1. SMT Gullwing
Package materials
Carrier tape : PS
Cover tape : PET (three layer system)
Reel : PS
Carrier tape structure and Dimensions
F
D
J
G
E
I
K
Dimensions List
(Unit : mm)
A
B
C
D
E
F
G
+0.1
16.0±0.3
7.5±0.1
1.75±0.1
8.0±0.1
2.0±0.1
4.0±0.1
φ1.5
−0
H
I
J
K
10.4±0.1
0.4±0.05
4.2±0.1
5.1±0.1
Reel structure and Dimensions
e
d
g
Dimensions List
(Unit : mm)
a
b
c
d
330
e
17.5±1.5
100±1.0
13±0.5
f
g
23±1.0
2.0±0.5
2.0±0.5
f
a
b
Direction of product insertion
Pull-out direction
[Packing : 2 000pcs/reel]
Sheet No.: D2-A02903EN
14
PC1231xNSZ0F Series
2. Wide SMT Gullwing
Package materials
Carrier tape : PS
Cover tape : PET (three layer system)
Reel : PS
Carrier tape structure and Dimensions
F
D
J
G
C
I
E
K
Dimensions List
(Unit : mm)
A
B
C
D
E
F
G
+0.1
24.0±0.3
11.5±0.1
1.75±0.1
8.0±0.1
2.0±0.1
4.0±0.1
φ1.5
−0
H
I
J
K
12.4±0.1
0.4±0.05
4.1±0.1
5.1±0.1
Reel structure and Dimensions
e
d
g
Dimensions List
(Unit : mm)
a
b
c
d
330
e
22.5±1.5
100±1.0
13±0.5
f
g
23±1.0
2.0±0.5
2.0±0.5
f
a
b
Direction of product insertion
Pull-out direction
[Packing : 2 000pcs/reel]
Sheet No.: D2-A02903EN
15
PC1231xNSZ0F Series
■ Important Notices
· The circuit application examples in this publication are
provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems
related to any intellectual property right of a third party
resulting from the use of SHARP's devices.
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in
connection with equipment that requires an extremely
high level of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the
specifications, characteristics, data, materials,
structure, and other contents described herein at any
time without notice in order to improve design or
reliability. Manufacturing locations are also subject to
change without notice.
· If the SHARP devices listed in this publication fall
within the scope of strategic products described in the
Foreign Exchange and Foreign Trade Law of Japan, it
is necessary to obtain approval to export such SHARP
devices.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be
reproduced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, in
whole or in part, without the express written permission
of SHARP. Express written permission is also required
before any use of this publication may be made by a
third party.
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
· Contact and consult with a SHARP representative if
there are any questions about the contents of this
publication.
[E223]
Sheet No.: D2-A02903EN
16
相关型号:
PC123AJ0000F
Transistor Output Optocoupler, 1-Element, 5000V Isolation, ROHS COMPLIANT, PLASTIC, DIP-4
SHARP
©2020 ICPDF网 联系我们和版权申明