S2S3R [SHARP]
Non-zero cross type Mini-Flat Package Phototriac Coupler for triggering; 非过零型微型扁平封装可控硅耦合器触发型号: | S2S3R |
厂家: | SHARP ELECTRIONIC COMPONENTS |
描述: | Non-zero cross type Mini-Flat Package Phototriac Coupler for triggering |
文件: | 总16页 (文件大小:271K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
S2S3 Series
VDRM : 600V, Non-zero cross type
Mini-Flat Package
Phototriac Coupler for triggering
S2S3 Series
∗Zero cross type is also available. (S2S4 Series)
■ Description
■ Agency approvals/Compliance
1. Recognized by UL1577 (Double protection isolation),
file No. E64380 (as model No. S2S3)
S2S3 Series Phototriac Coupler include an infrared
emitting diode (IRED) optically coupled to an output
Phototriac.
2. Approved by CSA, file No. CA95323 (as model No.
These devices feature full wave control and are
ideal isolated drivers for medium to high current Triacs.
SOP package provides 3.75kV isolation from input
to output with superior commutative noise immunity.
S2S3)
3. Optionary available VDE Approved (∗)(DIN EN
60747-5-2), file No. 40009162 (as model No. S2S3)
4. Package resin : UL flammability grade (94V-0)
(∗)
DIN EN60747-5-2 : successor standard of DIN VDE0884.
Up to Date code "RD" (December 2003), approval of DIN
VDE0884.
■ Features
From Date code "S1" (January 2004), approval of DIN
EN60747-5-2.
1. High repetitive peak off-state voltage (VDRM : 600V)
2. Non-zero crossing functionality
3. IFT ranks available (see Model Line-up section in this
datasheet)
(∗∗) Reinforced insulation type is also available.
(PC3SG11YIZ Series)
4. 4pin Mini-flat package
■ Applications
1. Triggering for Triacs used to switch on and off
5. Superior noise immunity (dV/dt : MIN. 100V/µs)
6. Lead-free components are also available (see Model
Line-up section in this datasheet)
7. Double transfer mold construction (Ideal for Flow
Soldering)
devices which require AC Loads.
For example heaters, fans, motors, solenoids, and
valves.
2. Triggering for Triacs used for implementing phase
control in applications such as lighting control and
temperature control (HVAC).
8. High isolation voltage between input and output
(Viso(rms) : 3.75kV)
3. AC line control in power supply applications.
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: D2-A06501EN
1
Date Mar. 31. 2004
© SHARP Corporation
S2S3 Series
■ Internal Connection Diagram
1
Anode
Cathode
Anode/Cathode
Cathode/Anode
1
4
2
3
4
2
3
(Unit : mm)
■ Outline Dimensions
VDE option
3.6±0.3
3.6±0.3
2.54±0.25
2.54±0.25
4
3
4
3
Date code (2 digit)
Model No.
Date code (2 digit)
Model No.
SHARP
mark "S"
SHARP
mark "S"
Anode
mark
Anode
mark
2 S 3
2 S 3
4
Factory identification mark
VDE identification mark
Factory identification mark
0.4±0.1
0.4±0.1
1
2
1
2
5.3±0.3
45˚
Epoxy resin
5.3±0.3
45˚
Epoxy resin
+0.4
−0.2
0.5
+0.4
−0.2
+0.2
−0.7
0.5
7.0
+0.2
−0.7
7.0
Product mass : approx. 0.09g
Product mass : approx. 0.09g
Sheet No.: D2-A06501EN
2
S2S3 Series
Date code (2 digit)
1st digit
2nd digit
Year of production
Month of production
A.D.
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
A.D
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
Mark
P
Month
Mark
1
Mark
A
B
January
February
March
R
2
S
3
C
T
April
4
D
E
U
May
5
F
V
June
6
H
J
W
X
July
7
August
September
October
November
December
8
K
L
A
9
B
O
N
D
M
N
C
·
·
·
·
·
·
repeats in a 20 year cycle
Factory identification mark
Factory identification Mark
Country of origin
no mark
Japan
Indonesia
Philippines
China
* This factory marking is for identification purpose only.
Please contact the local SHARP sales representative to see the actural status of the
production.
Rank mark
There is no rank mark indicator.
Sheet No.: D2-A06501EN
3
S2S3 Series
■ Absolute Maximum Ratings
(Ta=25˚C)
Parameter
Symbol
IF
Rating
50
Unit
mA
V
Forward current
Reverse voltage
RMS ON-state current
Peak one cycle surge current
Repetitive peak OFF-state voltage
Input
VR
6
A
IT(rms)
Isurge
0.05
0.6 *3
A
Output
V
VDRM
Viso(rms)
Topr
600
*1 Isolation voltage
kV
˚C
˚C
˚C
3.75
Operating temperature
Storage temperature
*2Soldering temperature
-30 to +100
-40 to +125
260
Tstg
Soldering area
Tsol
*1 40 to 60%RH, AC for 1minute, f=60Hz
*2 For 10s
*3 f=50Hz sine wave
■ Electro-optical Characteristics
(Ta=25˚C)
Symbol
VF
MIN.
Parameter
Conditions
IF=20mA
VR=3V
TYP. MAX.
Unit
V
Forward voltage
Input
−
−
1.2
1.4
10
1
IR
Reverse current
µA
µA
V
−
IDRM
VT
Repentitive peak OFF-state current
VD=VDRM
IT=0.05A
VD=6V
−
−
ON-state voltage
Output
−
−
2.5
3.5
−
Holding current
IH
mA
V/µs
0.1
100
−
−
1 000
−
−
Critical rate of rise of OFF-state voltage
dV/dt
VD=1/√2 ·VDRM
10
7
No rank
IFT
mA
−
Transfer
−
Minimum trigger current
Rank R
Rank L
VD=6V, RL=100Ω
−
5
charac-
teristics
−
5×1010 1011
−
Isolation resistance
Turn-on time
Ω
DC500V,40 to 60%RH
RISO
ton
−
−
100
VD=6V, RL=100Ω, IF=20mA
µs
Sheet No.: D2-A06501EN
4
S2S3 Series
■ Model Line-up (1) (Lead-free components)
Taping
Sleeve
Shipping Package
IFT[mA]
(VD=6V, RL=100Ω)
750pcs/reel
Approved
3 000pcs/reel
100pcs/sleeve
I
FT rank
DIN
EN60747-5-2
Approved
Approved
No rank
Rank R
Rank L
MAX.10
MAX.7
MAX.5
S2S3000F
S2S3R00F
S2S3L00F
S2S3A00F S2S3AY0F S2S3B00F S2S3BY0F
S2S3RA0F S2S3RAYF S2S3RB0F S2S3RBYF
S2S3Y00F
S2S3RY0F
S2S3LY0F
Model No.
S2S3LA0F
S2S3LB0F
■ Model Line-up (2) (Lead solder plating components)
Taping
Sleeve
Shipping Package
750pcs/reel
Approved
S2S3B S2S3BY
100pcs/sleeve
3 000pcs/reel
Approved
S2S3AY
IFT[mA]
(VD=6V, RL=100Ω)
IFT rank
DIN
EN60747-5-2
Approved
No rank
Rank R
Rank L
MAX.10
MAX.7
MAX.5
S2S3
S2S3R
S2S3L
S2S3Y
S2S3RY S2S3RA S2S3RAY S2S3RB S2S3RBY
S2S3LY S2S3LA S2S3LB
S2S3A
Model No.
Please contact a local SHARP sales representative to inquire about production status.
Sheet No.: D2-A06501EN
5
S2S3 Series
Fig.1 Forward Current vs.
Fig.2 RMS ON-state Current vs.
Ambient Temperature
Ambient Temperature
60
60
50
40
30
50
40
30
20
20
10
0
10
0
−30
0
50
100
−30
0
50
100
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Fig.3-a Forward Current vs. Forward Voltage
(No rank, Rank R)
Fig.3-b Forward Current vs. Forward Voltage
(Rank L)
100
100
Ta=100˚C
50
50
75˚C
50˚C
25˚C
Ta=75˚C
0˚C
0˚C
50˚C
−25˚C
−30˚C
25˚C
10
5
10
5
1
1
0.9
1
1.1
1.2
1.3
1.4
1.5
0
0.5
1
1.5
2
2.5
3
Forward voltage VF (V)
Forward voltage VF (V)
Fig.4 Minimum Trigger Current vs.
Ambient Temperature
Fig.5 Relative Repetitive Peak OFF-state
Voltage vs. Ambient Temperature
1.3
12
VD=6V
RL=100Ω
1.2
1.1
1
10
8
No rank
Rank R
6
0.9
4
Rank L
0.8
0.7
2
0
−40 −20
0
20
40
60
80
100
−40 −20
0
20
40
60
80
100
Ambient temperature Ta (°C)
Ambient temperature Ta (˚C)
Sheet No.: D2-A06501EN
6
S2S3 Series
Fig.6 ON-state Voltage vs.
Fig.7 Holding Current vs.
Ambient Temperature
Ambient Temperature
10
2
VD=6V
IT=50mA
1.8
1.6
1.4
1.2
1
1
0.1
0.8
−40 −20
0
20
40
60
80
100
−40 −20
0
20
40
60
80
100
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Fig.8 Repetitive Peak OFF-state Current vs.
OFF-state Voltage
Fig.9 Relative Repetitive Peak OFF-state
Current vs. Ambient Temperature
1 000
1
Ta=25˚C
VD=600V
100
10
1
0.1
0.01
0.1
0
20
40
60
80
100
100
200
300
400
500
600
Ambient temperature Ta (°C)
OFF-state voltage VD (V)
Fig.10-a Turn-on Time vs. Forward Current
(No Rank, Rank R)
Fig.10-b Turn-on Time vs. Forward Current
(Rank L)
1 000
1 000
VD=6V
VD=6V
RL=100Ω
Ta=25˚C
RL=100Ω
Ta=25˚C
100
100
10
10
1
10
100
1
10
100
Forward current IF (mA)
Forward current IF (mA)
Sheet No.: D2-A06501EN
7
S2S3 Series
Fig.11 ON-state Current vs. ON-state Voltage
100
IF=20mA
Ta=25˚C
80
60
40
20
0
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
ON-state voltage VT (V)
Remarks : Please be aware that all data in the graph are just for reference.
Sheet No.: D2-A06501EN
8
S2S3 Series
■ Design Considerations
● Design guide
In order for the Phototriac to turn off, the triggering current (IF), must be 0.1mA or less.
Please refrain from using these devices in a direct drive configuration.
These Phototriac Coupler are intended to be used as triggering device for main Triacs.
Please ensure that the output rating of these devices will be sufficient for triggering the main output Triac of
your choice. Failure to do may result in malfunctions.
In phase control applications or where the Phototriac Coupler is being by a pulse signal, please ensure that
the pulse width is a minimum of 1ms.
For designs that will experience excessive noise or sudden changes in load voltage, please include an
appropriate snubber circuit as shown in the below circuit.
Please keep in mind that Sharp Phototriac Couplers incorporate superor dV/dt ratings which can often
eliminate the need for a snubber circuit.
● Degradation
In general, the emission of the IRED used in Phototriac Couplers will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these Phototriac Couplers should
provide at least twice the minimum required triggering current from initial operation.
● Recommended Foot Print (reference)
6.3
1.5
(Unit : mm)
Sheet No.: D2-A06501EN
9
S2S3 Series
● Standard Circuit (Medium/High Power Triac Drive Circuit)
S2S3
1
4
3
Load
AC Line
Triac
2
Note) Please add the snubber circuit according to a condition.
Any snubber or varistor used for the above mentioned scenarios should be located
as close to the main output triac as possible.
✩
For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: D2-A06501EN
10
S2S3 Series
■ Manufacturing Guidelines
● Soldering Method
Reflow Soldering:
Reflow soldering should follow the temperature profile shown below.
Soldering should not exceed the curve of temperature profile and time.
Please don't solder more than twice.
(˚C)
300
Terminal : 260˚C peak
( package surface : 250˚C peak)
200
Reflow
220˚C or more, 60s or less
Preheat
100
150 to 180˚C, 120s or less
0
0
1
2
3
4
(min)
Flow Soldering :
Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below
listed guidelines.
Flow soldering should be completed below 260˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please don't solder more than twice.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400˚C.
Please don't solder more than twice.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
Sheet No.: D2-A06501EN
11
S2S3 Series
● Cleaning instructions
Solvent cleaning :
Solvent temperature should be 45˚C or below. Immersion time should be 3minutes or less.
Ultrasonic cleaning :
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials :
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol.
In case the other type of solvent materials are intended to be used, please make sure they work fine in
actual using conditions since some materials may erode the packaging resin.
● Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this device.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
Sheet No.: D2-A06501EN
12
S2S3 Series
■ Package specification
● Sleeve package
Package materials
Sleeve : HIPS (with anti-static material)
Stopper : Styrene-Elastomer
Package method
MAX. 100pcs of products shall be packaged in a sleeve.
Both ends shall be closed by tabbed and tabless stoppers.
The product shall be arranged in the sleeve with its anode mark on the tabless stopper side.
MAX. 50 sleeves in one case.
Sleeve outline dimensions
10.5
4.6
4.5
(Unit : mm)
Sheet No.: D2-A06501EN
13
S2S3 Series
● Tape and Reel package
1. 3 000pcs/reel
Package materials
Carrier tape : A-PET (with anti-static material)
Cover tape : PET (three layer system)
Reel : PS
Carrier tape structure and Dimensions
F
E
D
G
J
I
M A X .
K
5 ˚
Dimensions List
(Unit : mm)
A
B
C
D
E
F
G
+0.1
12.0±0.3
5.5±0.1
1.75±0.1
8.0±0.1
2.0±0.1
4.0±0.1
φ1.5
−0
H
I
J
K
7.4±0.1
0.3±0.05
3.1±0.1
4.0±0.1
Reel structure and Dimensions
e
d
g
Dimensions List
(Unit : mm)
a
b
c
d
370
e
13.5±1.5
80±1.0
g
13±0.5
f
f
21±1.0
2.0±0.5
2.0±0.5
a
b
Direction of product insertion
Pull-out direction
[Packing : 3 000pcs/reel]
Sheet No.: D2-A06501EN
14
S2S3 Series
2. 750pcs/reel
Package materials
Carrier tape : A-PET (with anti-static material)
Cover tape : PET (three layer system)
Reel : PS
Carrier tape structure and Dimensions
F
E
D
G
J
I
M A X .
K
5 ˚
Dimensions List
(Unit : mm)
A
B
C
D
E
F
G
+0.1
12.0±0.3
5.5±0.1
1.75±0.1
8.0±0.1
2.0±0.1
4.0±0.1
φ1.5
−0
H
I
J
K
7.4±0.1
0.3±0.05
3.1±0.1
4.0±0.1
Reel structure and Dimensions
e
d
g
Dimensions List
(Unit : mm)
a
b
c
d
180
e
21±1.0
13.5±1.5
80±1.0
g
2.0±0.5
13±0.5
f
f
a
b
2.0±0.5
Direction of product insertion
Pull-out direction
[Packing : 750pcs/reel]
Sheet No.: D2-A06501EN
15
S2S3 Series
■ Important Notices
· The circuit application examples in this publication are
provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems rela-
ted to any intellectual property right of a third party re-
sulting from the use of SHARP's devices.
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in connec-
tion with equipment that requires an extremely high lev-
el of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the spec-
ifications, characteristics, data, materials, structure,
and other contents described herein at any time without
notice in order to improve design or reliability. Manufac-
turing locations are also subject to change without no-
tice.
· If the SHARP devices listed in this publication fall with-
in the scope of strategic products described in the For-
eign Exchange and Foreign Trade Law of Japan, it is
necessary to obtain approval to export such SHARP de-
vices.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be repro-
duced or transmitted in any form or by any means, elec-
tronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any
use of this publication may be made by a third party.
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
· Contact and consult with a SHARP representative if
there are any questions about the contents of this pub-
lication.
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
Sheet No.: D2-A06501EN
16
相关型号:
S2S3RP
Silicon Controlled Rectifier, 0.8A I(T)RMS, 200V V(DRM), 200V V(RRM), 1 Element, 3 LEAD
LITTELFUSE
©2020 ICPDF网 联系我们和版权申明