VT4T5UF2021 [SHARP]
Combination Tuner/Demodulator/Modulator; 组合调谐器/解调器/调制器型号: | VT4T5UF2021 |
厂家: | SHARP ELECTRIONIC COMPONENTS |
描述: | Combination Tuner/Demodulator/Modulator |
文件: | 总8页 (文件大小:107K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
VT4T5UF2021
Combination Tuner/Demodulator/Modulator
RF Data Sheet
FEATURES
• Receiving Standard: USA
• Receiving Channels:
– VHF Section
– Low Band – Air: 2 to 6 CATV: (A-8) A-5 to B
– High Band – Air: 7 to 13 CATV: C to W + 11
– UHF Section
– Air: 14 to 69
– CATV: W + 12 to W + 84
• Sending Channels:
– USA Channel 3 and 4
– CH 3: OPEN
– CH 4: GND
• Receiving and Sending System: USA Standard
M-System (NTSC)
• Channel Selection System: PLL Tuning
COMB4-1
• Detection System: Dummy Synchronization Detec-
tion System, Intercarrier Sound Receiving System
• Nominal Input Impedance:
– RF: 75 Ω, Unbalanced
FUNCTIONAL DESCRIPTION
The VT4T5UF2021 is a combination tuner, demodu-
lator and modulator in one package. This unit is compat-
ible with North American NTSC television broadcast
signals. An internal Phase-Locked Loop circuit per-
forms all of the required tuning functions. Digital control
information is provided to the unit on I2C serial data
bus. The tuner and demodulator blocks are internally
connected, providing an IF sample point for test pur-
poses. The modulator has separate video and audio
inputs and control connections. This single package
configuration is useful when there is no need to manip-
ulate the AGC or IF signals prior to demodulation, and
provides for a simplified system design. The RF con-
nectors are mounted on the end of the housing so that-
the smallest possible area is used on the rear panel of
the end product.
– Video: 1 kΩ, Unbalanced
– Audio: 4.7 Ω MIN., Unbalanced
– Control: 30 kΩ MIN., Unbalanced
• Output Load Impedance:
– RF: 75 Ω
– Video: 1 kΩ
– Audio: 4.7 kΩ
• Intermediate Frequency:
– Picture: 45.75 MHz
– Sound: 41.25 MHz
• Weight: 72 g ±10 g
• Applicable Standards:
– EIA Standard Number 544
– EIA Standard Number 16A
– FCC Standards
The RF pass-through feature is electrically controlled
via an external interface pin. Output channel 3 or 4 is
also electrically selected by asserting 5 V or ground on
an external pin. The internal tuner sample point is
always active, allowing the tuner and demodulator func-
tions to be used at all times, regardless of the condition
of the RF pass-through and the modulator output.
Demodulated audio, video AGC and AFT outputs are
also provided. The AGC control line from the demodula-
tor to the tuner is not accessible to the system designer.
– UL Standard
RF Data Sheet
1
VT4T5UF2021
Combination Tuner/Demodulator/Modulator
ANT
IN
TV OUT
RF SW
HPF
DISTRIBUTOR
RF SW
BPF
WHITE
CLIPPER
VIDEO
IN
VIDEO
CLAMPER
MODULATOR
CH.
SW
RF
CARRIER
OSC
SAW
RESONATOR
AMP
AUDIO
IN
FM
PRE-EMPHASIS
MODULATOR
4.5 MHz
TANK
U/V ONE CHIP AND IC
UHF
INPUT
TUNING
CIRCUIT
RF
AMP
INTERSTAGE
TUNING
CIRCUIT
MIX
OSC
RESONANCE
CIRCUIT
~
IF
AMP
U/V SEPARATE
FILTER
IF TUNING
CIRCUIT
VHF
RF
AMP
INPUT
TUNING
CIRCUIT
INTERSTAGE
TUNING
CIRCUIT
OSC
RESONANCE
CIRCUIT
~
PLL CIRCUIT
VIDEO AMP
SIF
TRAP
VIDEO OUT
SIF
FILTER
PRE-AMP
DET
OUT
SAW
FILTER
SF IN
AUDIO OUT
DEMODULATOR
IC
AFT OUT
AFT MUTE
RF AGC
COMB3-6
Figure 1. VT4T5UF2021 Block Diagram
2
RF Data Sheet
Combination Tuner/Demodulator/Modulator
VT4T5UF2021
• RF Output (Output System). Measured sync level at
whilte 100% signal, input 1 Vp-p.
ELECTRICAL CHARACTERISTICS
• Nominal Supply Voltage (TYP.)
– BM: 5 V
– Video Carrier Center Frequency Accuracy
±10 kHz (TYP.), ±100 kHz (MAX.)
– Sound Carrier Center Frequency Accuracy
4.5 MHz (TYP.), 4.5 MHz ±7 kHz
– Video Carrier Output Level 66 dBµ (TYP.),
66 ±3 dBµ
– P/S Ratio 16 dB (TYP.), 16 ±3 dB
– BT: 33 V
– BP: 5 V
– B: 5 V
• Operating Voltage (TYP.)
– BM: 5V ±0.2 V
– BT: 33 V ±2.0 V
– BP: 5 V ±0.5 V
– B: 5 V ±0.5 V
• RF Output Spurious.
– Specific Frequency 70 dB (TYP.), 60 dB (MIN.)
– fp to fp + 4.5 MHz
– Other Frequencies 50 dB (TYP.), 30 dB (MIN.)
– 0 to 1 GHz (except fp ±4.6 MHz)
– Control: 5 V ±0.2 V
• Breakdown Voltage (MIN.)
– BM: 5.5 V
• RF Switch
– BT: 34 V
– BP: 5.5 V
– B: 5.5 V
– Insertion Loss: 55 to 806 MHz
– 4.0 dB (TYP.), 8.0 dB (MAX.)
– Isolation: 61 to 72 MHz
– 70 dB (TYP.), 60 dB (MIN.)
– Return Loss: 61 to 72 MHz
– 8.0 dB (TYP.), 4.0 dB (MIN.)
• Test Conditions (TYP.)
– BM: 5 V
– BT: 33 V
– BP: 5 V
– B: 5 V
– Ambient Temperature 25°C ±5°C
– Relative Humidity 65% ±10%
• RF Switch Operation (dBµ)
– Terminal Number 4: RF OUT ← RF IN (TYP.)
– +5 V: OFF
– Open: ON
• Current Consumption (MAX.)
– BM: 1.0 mA
• Antenna Terminal Voltage
– Modulator OSC Leakage 9.5 dBµ (MAX.)
– Tuner OSC Leakage
– BT: 5 mA
– BP: 70 mA
– B: 40 mA
– Fundamental Wave 60 dBµ (MAX.)
– Higher Harmonic 60 dBµ (MAX.)
• Temperature (TYP.)
• Noise Figure (UHF AIR)
– Storage -20°C to +70°C
– Operating -10°C to +60°C
– Maximum 11 dB (TYP.), 16 dB (MAX.)
–
X = Σxi ⁄ n
• RF Output (Video System). Measured by standard
demodulator input 1 Vp-p.
S = Σ (Xi – x)2 ⁄ (n – 2), n = 10*
– Modulation Factor 80% (TYP.), 80 ±5%
– Differential Gain 2% (TYP.), 7% (MAX.)
– Differential Phase 1.5° (TYP.), 8° (MAX.)
– S/N Ratio 55 dB (TYP.), 48 dB (MIN.)
– Frequency Characteristics 0 dB (TYP.), 0 ±3 dB
– Change in Modulation Factor to APL 1% (TYP.),
5% (MAX.)
(Tested channels including worst)
– Shall satisfy the requirements stated in FCC
NF Sampling Plan C (effective January, 1980)
– Noise figure measurement shall be based on
FCC OST 50 (effective January, 1980)
– XIRS 11 dB (TYP.), 16 dB (MAX.)
–
• RF Output (Audio System). Measured by standard
demodulator input 1 kHz, 1.24 Vp-p sincurve.
– Modulation Factor ±22.5 kHz (TYP.),
±22.5 kHz - ±5.5 kHz
X = Σxi ⁄ n
S = Σ (Xi – x)2 ⁄ (n – 2), n = 10*
(Tested channels including worst)
– Distortion Rate 0.3% (TYP.), 1% (MAX.)
– S/N Ratio 56 dB (TYP.), 48 dB (MIN.)
– Frequency Characteristics 0 dB (TYP.), 0 ±3 dB
– Noise figure measurement shall be based on
FCC OST 50 (effective January, 1980)
NOTE: *A representative tuner test shall be conducted on the follow-
ing channels and on the worst channel found CH 14 through CH69:
Ch14, 20, 26, 32, 38, 44, 50, 56, 62, and 69.
RF Data Sheet
3
VT4T5UF2021
Combination Tuner/Demodulator/Modulator
• Image Rejection
• Picture Output.
– At -47 dBM Input
– Output Level (CH 10) 1 Vp-p (TYP.), 1 ±2 Vp-p
– At 1 kΩ termination, fp 70 dBµ, white 100%
– Differential Gain (CH 10) 5° (TYP.), 10° (MAX.)
– fp 90 dBµ, Sterstep 80 IRE
– Differential Phase (CH 10) 1° (TYP.), 10° (MAX.)
– fp 90 dBµ, Sterstep 80 IRE
– S/N ratio 47 dB (TYP.), 43 dB (MIN.)
– fp 70 dBµ, White 100%, 100 kHz to 4.2 MHz fil-
ter, Sctrap On
– Frequency Characteristics (CH 10), fp 70 dBµ,
multi-burst
– 1.0 MHz: 0 dB (TYP.), -3 to +3 dB
– 2.0 MHz: 0 dB (TYP.), -3 to +3 dB
– 3.0 MHz: -1.0 dB (TYP.), -4.5 dB to +2.5 dB
– 3.58 MHz: -1.0 dB (TYP.), 0 dB to 6 dB
– Synchronized Ratio (CH 10) 28.5% (TYP.),
23.6% to 33.6%
– VHF Air: 65 dB (TYP.), 60 dB (MIN.)
– VHF CATV: 60 dB (TYP.), 50 dB (MIN.)
– UHF: 55 dB (TYP.), 45 dB (MIN.)
– At -17 dBM: Input
– VHF Air: 60 dB (TYP.), 50 dB (MIN.)
– VHF CATV: 50 dB (TYP.), 40 dB (MIN.)
– UHF: 50 dB (TYP.), 35 dB (MIN.)
• IF Rejection
– At -47 dBM: Input
– VHF Low: 60 dB (TYP.), 50 dB (MIN.)
– VHF High: 100 dB (TYP.), 60 dB (MIN.)
– UHF 100: dB (TYP.), 60 dB (MIN.)
– At -17 dBM Input
– VHF Low: 60 dB (TYP.), 45 dB (MIN.)
– VHF High: 70 dB (TYP.), 50 dB (MIN.)
– UHF: 70 dB (TYP.), 40 dB (MIN.)
– fp 70 dBµ, SMPTE color bar
• CB Rejection
• Sound Output (CH 10)
– SI: 50 dB (TYP.), 40 dB (MIN.)
– Undesirable: 0.535 MHz to 30 MHz
– -7 Input (MIN.)
– Desirable: 55.25 MHz to 83.25 MHz (CH 2 to Ch 6)
– -66 Input (MIN.)
– Output Level 480 mVrms (TYP.), 360 mVrms to
580 mVrms
– fp 70 dBµ, SMPTE color bar 87.5% modula-
tion, P/S 6 dB, fs 1 kHz, sin-curve 60% modu-
lation, 75 µs pre-emphasis
• Specific Channel Rejection
– Distortion Rate 0.5% (TYP.), 3.0% (MAX.)
– S/N Ratio 52 dB (TYP.), 42 dB (MAX.)
– Frequency Characteristics 0 dB (TYP.), 0 ±3 dB
– AM Removal Level 45 dB (TYP.), 35 dB (MAX.)
– Desirable 54 dBµ input; Undesireable 49 dbµ input
– CH A-3 ← CH A-5: 60 dB (TYP.); 55 dB (MIN.)
– CH 6 ← CH A-5: 55 dB (TYP.); 50 dB (MIN.)
– CH A-5 ← CH A-5: 60 dB (TYP.); 50 dB (MIN.)
– CHP 5 ← CHS 6: 55 dB (TYP.); 52 dB (MIN.)
– CHP 5 ← CHP 6: 60 dB (TYP.); 45 dB (MIN.)
• AFT Output
– Output Voltage 2.5 V (TYP.), 1.75 V to 3.25 V
– Frequency Accuracy 25 kHz (TYP.), 100 kHz (MAX.)
• Band Edge Tuning Margin
– CH 2: -4.0 MHz (TYP.), -3.25 MHz (MIN.)
– CH B: 3.0 MHz (TYP.), 2.0 MHZ (MIN.)
– CH C: -4.0 MHz (TYP.), -3.25 MHz (MIN.)
– CH W + 11: 3.0 MHz (TYP.), 2.0 MHz (MIN.)
– CH W + 12: -5.0 MHz (TYP.), -3.25 MHz (MIN.)
– CH 69: 5.0 MHz (TYP.), 2.0 MHz (MIN.)
60
50
40
30
20
54 dBµ
46 dBµ
43.5 dBµ
• PLL AC Characteristics
– Setting Up Enable: Tsuen 1 µs (MIN.)
– Holding Enable: Thden 1 µs (MIN.)
– Setting Up Data: Tsuda 1 µs (MIN.)
– Holding Data: Thdda 1 µs (MIN.)
– Clock Level High: Thicl 1 µs (MIN.)
– Clock Level Low: Tlocl 1 µs (MIN.)
– Clock Rate: Trate 10 µs (MIN.)
– Signal Rising: Trise 1 µs (MIN.)
– Signal Falling: Tfall 1 µs (MIN.)
88 216
960
5000
FREQUENCY (MHz)
COMB3-4
Figure 2. Radiation (3m Method)
4
RF Data Sheet
Combination Tuner/Demodulator/Modulator
VT4T5UF2021
105
95
85
75
65
50
60
70
80
90
100
110
UNDESIRED INPUT LEVEL (dBµ)
NOTE: Input levels causing 1% cross modulation are shown in shaded area.
COMB3-2
Figure 3. Cross Modulation Between Next and Adjacent Channels
105
95
85
75
65
50
60
70
UNDESIRED INPUT LEVEL (dBµ)
NOTE: Input levels causing 1% cross modulation are shown in shaded area.
80
90
100
110
COMB3-3
Figure 4. Cross Modulation Between Adjacent Channels
tRISE tSUEN
tFALL
90%
10%
ENABLE
tSUDA tHDDA
tHDEN
90%
10%
DATA
tHIEL
90%
10%
CLOCK
tLOEL
tRATE
COMB3-5
Figure 5. PLL AC Characteristics
RF Data Sheet
5
VT4T5UF2021
Combination Tuner/Demodulator/Modulator
OUTLINE DIMENSIONS
6
RF Data Sheet
Combination Tuner/Demodulator/Modulator
VT4T5UF2021
RF Data Sheet
7
VT4T5UF2021
Combination Tuner/Demodulator/Modulator
LIFE SUPPORT POLICY
SHARP components should not be used in medical devices with life support functions or in safety equipment (or similiar applications where
component failure would result in loss of life or physical harm) without the written approval of an officer of the SHARP Corporation.
LIMITED WARRANTY
SHARP warrants to its Customer that the Products will be free from defects in material and workmanship under normal use and service for a
period of one year from the date of invoice. Customer's exclusive remedy for breach of this warranty is that SHARP will either (i) repair or
replace, at its option, any Product which fails during the warranty period because of such defect (if Customer promptly reported the failure to
SHARP in writing) or, (ii) if SHARP is unable to repair or replace, refund the purchase price of the Product upon its return to SHARP. This
warranty does not apply to any Product which has been subjected to misuse, abnormal service or handling, or which has been altered or
modified in design or construction, or which has been serviced or repaired by anyone other than Sharp. The warranties set forth herein are in
lieu of, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY
EXCLUDED. In no event will Sharp be liable, or in any way responsible, for any incidental or consequential economic or property damage.
The above warranty is also extended to Customers of Sharp authorized distributors with the following exception: reports of failures of Products
during the warranty period and return of Products that were purchased from an authorized distributor must be made through the distributor.
In case Sharp is unable to repair or replace such Products, refunds will be issued to the distributor in the amount of distributor cost.
SHARP reserves the right to make changes in specifications at any time and without notice. SHARP does not assume any responsibility
for the use of any circuitry described; no circuit patent licenses are implied.
NORTH AMERICA
EUROPE
ASIA
SHARP Corporation
SHARP Microelectronics
of the Americas
5700 NW Pacific Rim Blvd., M/S 20
Camas, WA 98607, U.S.A.
Phone: (360) 834-2500
Telex: 49608472 (SHARPCAM)
Facsimile: (360) 834-8903
http://www.sharpsma.com
SHARP Electronics (Europe) GmbH
Microelectronics Division
Sonninstraße 3
20097 Hamburg, Germany
Phone: (49) 40 2376-2286
Facsimile: (49) 40 2376-2232
http://www.sharpmed.com
Integrated Circuits Group
2613-1 Ichinomoto-Cho
Tenri-City, Nara, 632, Japan
Phone: (07436) 5-1321
Telex: LABOMETA-B J63428
Facsimile: (07436) 5-1532
©1999 by SHARP Corporation
Reference Code SMA99024
相关型号:
VT5-254AP
Through hole VC-TCXO Clipped sine wave Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254AP3
Through hole VC-TCXO Clipped sine wave Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254AP5
Through hole VC-TCXO Clipped sine wave Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254HL
SMD VC-TCXO HCMOS Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254HL3
SMD VC-TCXO HCMOS Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254HL5
SMD VC-TCXO HCMOS Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254HP
Through hole VC-TCXO HCMOS Tight frequency stability vs temperatureWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254HP5
Through hole VC-TCXO HCMOS Tight frequency stability vs temperatureWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-254SP
Through hole VC-TCXOWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-256AL
Frequency range up to 200 MHz Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-256AL3
Frequency range up to 200 MHz Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
VT5-256AL5
Frequency range up to 200 MHz Low phase noiseWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
QUARTZCOM
©2020 ICPDF网 联系我们和版权申明