S-8200ABM-M6T1U [SII]
BATTERY PROTECTION IC FOR 1-CELL PACK;型号: | S-8200ABM-M6T1U |
厂家: | SEIKO INSTRUMENTS INC |
描述: | BATTERY PROTECTION IC FOR 1-CELL PACK 光电二极管 |
文件: | 总36页 (文件大小:1961K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
S-8200A Series
BATTERY PROTECTION IC FOR 1-CELL PACK
www.sii-ic.com
© SII Semiconductor Corporation, 2010-2015
Rev.4.0_02
The S-8200A Series is a protection IC for lithium-ion / lithium polymer rechargeable batteries and includes high-accuracy
voltage detection circuits and delay circuits.
The S-8200A Series is suitable for protecting 1-cell lithium-ion / lithium polymer rechargeable battery packs from overcharge,
overdischarge, and overcurrent.
Features
• High-accuracy voltage detection circuit
Overcharge detection voltage
3.5 V to 4.5 V (5 mV step)
Accuracy 20 mV (Ta = +25°C)
Accuracy 25 mV (Ta = −10°C to +60°C)
Accuracy 30 mV
Overcharge release voltage
3.1 V to 4.5 V*1
Overdischarge detection voltage
Overdischarge release voltage
Discharge overcurrent detection voltage
Charge overcurrent detection voltage
2.0 V to 3.4 V (10 mV step)
2.0 V to 3.4 V*2
0.05 V to 0.20 V (10 mV step)
Accuracy 35 mV
Accuracy 50 mV
Accuracy 10 mV
−0.20 V to −0.05 V (25 mV step) Accuracy 15 mV
• Detection delay times are generated only by an internal circuit (external capacitors are unnecessary).
Accuracy 20%
• High-withstand voltage (VM pin and CO pin: Absolute maximum rating = 28 V)
• 0 V battery charge function "available" / "unavailable" is selectable.
• Power-down function "available" / "unavailable" is selectable.
• Wide operation temperature range
• Low current consumption
During operation
Ta = −40°C to +85°C
2.8 μA typ., 5.0 μA max. (Ta = +25°C)
0.1 μA max. (Ta = +25°C)
During power-down
• Lead-free (Sn 100%), halogen-free
*1. Overcharge release voltage = Overcharge detection voltage − Overcharge hysteresis voltage
(Overcharge hysteresis voltage can be selected as 0 V or from a range of 0.1 V to 0.4 V in 50 mV step.)
*2. Overdischarge release voltage = Overdischarge detection voltage + Overdischarge hysteresis voltage
(Overdischarge hysteresis voltage can be selected as 0 V or from a range of 0.1 V to 0.7 V in 100 mV step.)
Applications
• Lithium-ion rechargeable battery pack
• Lithium polymer rechargeable battery pack
Packages
• SOT-23-6
• SNT-6A
1
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Block Diagram
Output control circuit
0 V battery charge /
Oscillator control
circuit
Divider control
charge inhibition circuit
DO
circuit
VDD
+
−
Charger detection circuit
CO
Overcharge
detection
+
comparator
−
Discharge overcurrent detection
comparator
RVMD
+
−
VM
+
−
Charge overcurrent detection
comparator
RVMS
Overdischarge
detection
comparator
+
−
Load short-circuiting detection
comparator
VSS
Remark All diodes shown in figure are parasitic diodes.
Figure 1
2
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Product Name Structure
1. Product name
S-8200A xx
-
xxxx
U
Environmental code
U: Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications*1
M6T1: SOT-23-6, Tape
I6T1: SNT-6A, Tape
Serial code*2
Sequentially set from AA to ZZ
*1. Refer to the tape drawing.
*2. Refer to "3. Product name list".
2. Packages
Table 1 Package Drawing Codes
Package Name
SOT-23-6
SNT-6A
Dimension
Tape
Reel
Land
MP006-A-P-SD
PG006-A-P-SD
MP006-A-C-SD
PG006-A-C-SD
MP006-A-R-SD
PG006-A-R-SD
−
PG006-A-L-SD
3
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
3. Product name list
3. 1 SOT-23-6
Table 2
Discharge
Overcurrent
Detection
Voltage
Over-
Over-
Over-
Over-
Load short-
circuiting
Detection
Voltage
Charge
charge
charge discharge discharge
Overcurrent 0 V Battery
Delay
Power-
down
Product Name
Detection Release Detection Release
Voltage Voltage Voltage Voltage
[VCU [VCL [VDL [VDU
Detection
Voltage
Charge
Time
Combination*1
Function
Function
[VDIOV
]
]
]
]
]
[VSHORT
]
[VCIOV]
S-8200AAC-M6T1U
S-8200AAH-M6T1U
S-8200AAY-M6T1U
S-8200ABE-M6T1U
4.225 V 4.025 V 2.500 V
4.375 V 4.175 V 2.300 V
4.150 V 4.050 V 2.500 V
4.200 V 4.000 V 3.200 V
2.900 V
2.300 V
2.800 V
3.400 V
2.300 V
2.500 V
3.000 V
3.000 V
2.500 V
2.500 V
0.150 V
0.130 V
0.160 V
0.150 V
0.130 V
0.050 V
0.190 V
0.200 V
0.100 V
0.085 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
−0.150 V
−0.100 V
−0.100 V
−0.100 V
−0.125 V
−0.050 V
−0.075 V
−0.100 V
−0.100 V
−0.100 V
Available
(1)
(2)
(1)
(2)
(1)
(1)
(2)
(3)
(1)
(1)
Unavailable
Available
Unavailable
Available
Available
Available
Available
Available
Available
Available
Available
Available
Unavailable
Unavailable
Available
S-8200ABM-M6T1U 4.280 V 4.180 V 2.300 V
S-8200ABX-M6T1U
S-8200ABZ-M6T1U
S-8200ACF-M6T1U
S-8200ACV-M6T1U
4.280 V 4.280 V 2.500 V
4.280 V 4.080 V 3.000 V
4.350 V 4.000 V 2.400 V
4.350 V 4.150 V 2.400 V
Available
Available
Unavailable
Unavailable
S-8200ACW-M6T1U 4.350 V 4.150 V 2.400 V
*1. Refer to Table 4 about the details of the delay time combinations.
3. 2 SNT-6A
Table 3
Discharge
Overcurrent
Detection
Voltage
Over-
Over-
Over-
Over-
Load short-
circuiting
Detection
Voltage
Charge
Overcurrent 0 V Battery
charge
charge discharge discharge
Delay
Time
Combination*1
Power-
down
Product Name
Detection Release Detection Release
Voltage Voltage Voltage Voltage
[VCU [VCL [VDL [VDU
Detection
Voltage
Charge
Function
Function
[VDIOV
]
]
]
]
]
[VSHORT
]
[VCIOV]
Available
Available
Unavailable
Available
Available
Available
Available
Available
Available
Available
Available
Available
Available
Available
Available
Available
Available
S-8200AAA-I6T1U
S-8200AAB-I6T1U
S-8200AAC-I6T1U
S-8200AAD-I6T1U
S-8200AAF-I6T1U
S-8200AAG-I6T1U
S-8200AAH-I6T1U
S-8200ABA-I6T1U
S-8200ABI-I6T1U
S-8200ABK-I6T1U
S-8200ABL-I6T1U
S-8200ABM-I6T1U
S-8200ACN-I6T1U
S-8200ACO-I6T1U
S-8200ACP-I6T1U
S-8200ACQ-I6T1U
S-8200ACR-I6T1U
4.225 V 4.025 V 2.500 V
4.250 V 4.050 V 2.400 V
4.225 V 4.025 V 2.500 V
4.275 V 4.075 V 2.600 V
4.225 V 4.025 V 2.800 V
4.275 V 4.075 V 2.600 V
4.375 V 4.175 V 2.300 V
4.425 V 4.225 V 2.300 V
4.275 V 4.175 V 2.300 V
3.500 V 3.400 V 2.500 V
4.390 V 4.190 V 2.500 V
4.280 V 4.180 V 2.300 V
4.275 V 4.075 V 2.800 V
4.320 V 4.120 V 2.800 V
4.390 V 4.290 V 2.700 V
4.420 V 4.220 V 2.600 V
4.280 V 4.180 V 2.300 V
2.900 V
2.900 V
2.900 V
2.600 V
2.800 V
2.600 V
2.300 V
2.300 V
2.400 V
2.800 V
2.500 V
2.300 V
2.800 V
2.800 V
2.700 V
2.600 V
2.300 V
0.150 V
0.050 V
0.150 V
0.120 V
0.150 V
0.180 V
0.130 V
0.165 V
0.025 V
0.100 V
0.130 V
0.130 V
0.200 V
0.220 V
0.130 V
0.120 V
0.120 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.175 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
0.500 V
−0.150 V
−0.100 V
−0.150 V
−0.100 V
−0.150 V
−0.125 V
−0.100 V
−0.100 V
−0.050 V
−0.100 V
−0.125 V
−0.125 V
−0.150 V
−0.200 V
−0.125 V
−0.125 V
−0.100 V
Unavailable
Unavailable
Available
(1)
(1)
(1)
(2)
(1)
(2)
(2)
(2)
(4)
(2)
(1)
(1)
(4)
(5)
(2)
(6)
(6)
Available
Unavailable
Available
Available
Unavailable
Available
Available
Unavailable
Unavailable
Available
Unavailable
Unavailable
Available
Unavailable
*1. Refer to Table 4 about the details of the delay time combinations.
Remark Please contact our sales office for the products with detection voltage value other than those specified above.
4
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Table 4
Overcharge
Detection
Delay Time
Overdischarge
Detection
Delay Time
[tDL]
Discharge Overcurrent Load Short-circuiting
Charge Overcurrent
Detection
Detection
Detection
Delay Time
Combination
Delay Time
Delay Time
Delay Time
[tCU
]
[tDIOV
]
[tSHORT
]
[tCIOV]
(1)
(2)
(3)
(4)
(5)
(6)
1.0 s
1.0 s
64 ms
32 ms
8 ms
8 ms
250 μs
250 μs
250 μs
250 μs
500 μs
250 μs
8 ms
8 ms
256 ms
1.0 s
32 ms
8 ms
16 ms
8 ms
128 ms
128 ms
128 ms
8 ms
1.0 s
16 ms
16 ms
16 ms
8 ms
1.0 s
Remark The delay times can be changed within the range listed in Table 5. For details, please contact our sales office.
Table 5
Delay Time
Symbol
tCU
Selection Range
Remark
Overcharge detection delay time
Overdischarge detection delay time
256 ms
512 ms
64 ms*1
8 ms*1
500 μs
8 ms*1
1.0 s*1
Select a value from the left.
tDL
32 ms
128 ms Select a value from the left.
Discharge overcurrent detection delay time tDIOV
4 ms
16 ms
1 ms
Select a value from the left.
Select a value from the left.
Select a value from the left.
Load short-circuiting detection delay Time
Charge overcurrent detection delay time
tSHORT
tCIOV
250 μs*1
4 ms
16 ms
*1. This value is the delay time of the standard product.
5
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Pin Configurations
1. SOT-23-6
Table 6
Top view
Pin No.
1
Symbol
DO
Description
6
1
5
4
Connection pin of discharge control FET gate
(CMOS output)
Voltage detection pin between VM pin and VSS pin
(Overcurrent / charger detection pin)
Connection pin of charge control FET gate
(CMOS output)
2
3
VM
CO
2
3
4
5
6
NC*1
VDD
VSS
No connection
Figure 2
Input pin for positive power supply
Input pin for negative power supply
*1. The NC pin is electrically open.
The NC pin can be connected to VDD pin or VSS pin.
2. SNT-6A
Top view
Table 7
Pin No.
1
Symbol
NC*1
Description
1
2
3
6
5
4
No connection
Connection pin of charge control FET gate
(CMOS output)
2
3
CO
DO
Connection pin of discharge control FET gate
(CMOS output)
Figure 3
4
5
VSS
VDD
Input pin for negative power supply
Input pin for positive power supply
Voltage detection pin between VM pin and VSS pin
(Overcurrent / charger detection pin)
6
VM
*1. The NC pin is electrically open.
The NC pin can be connected to VDD pin or VSS pin.
6
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Absolute Maximum Ratings
Table 8
(Ta = +25°C unless otherwise specified)
Item
Input voltage between VDD pin and VSS pin
VM pin input voltage
Symbol
VDS
Applied Pin
Absolute Maximum Rating
Unit
VDD
VM
DO
CO
−
VSS − 0.3 to VSS + 12
VDD − 28 to VDD + 0.3
VSS − 0.3 to VDD + 0.3
VVM − 0.3 to VDD + 0.3
650*1
V
V
VVM
VDO
VCO
DO pin output voltage
V
CO pin output voltage
V
SOT-23-6
Power dissipation
mW
mW
°C
°C
PD
SNT-6A
−
−
400*1
Operation ambient temperature
Storage temperature
Topr
Tstg
−40 to +85
−
−55 to +125
*1. When mounted on board
[Mounted board]
(1) Board size: 114.3 mm × 76.2 mm × t1.6 mm
(2) Board name: JEDEC STANDARD51-7
Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
700
SOT-23-6
SNT-6A
600
500
400
300
200
100
0
0
50
100
150
Ambient Temperature (Ta) [°C]
Figure 4 Power Dissipation of Package (When Mounted on Board)
7
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Electrical Characteristics
1. Ta = +25°C
Table 9
(Ta = +25°C unless otherwise specified)
Test
Circuit
Item
Symbol
VCU
Condition
Min.
Typ.
Max.
Unit
Detection Voltage
−
VCU − 0.020
VCU − 0.025
VCL − 0.030
VCL − 0.025
VDL − 0.035
VDU − 0.050
VDU − 0.035
VDIOV − 0.010 VDIOV VDIOV + 0.010
VSHORT − 0.100 VSHORT VSHORT + 0.100
VCIOV − 0.015 VCIOV VCIOV + 0.015
VCU
VCU
VCL
VCL
VDL
VDU
VDU
VCU + 0.020
VCU + 0.025
VCL + 0.030
VCL + 0.020
VDL + 0.035
VDU + 0.050
VDU + 0.035
V
V
V
V
V
V
V
V
V
V
1
1
1
1
2
2
2
2
2
2
Overcharge detection voltage
Ta = −10°C to +60°C*1
VCL ≠ VCU
VCL = VCU
VCL
VDL
VDU
Overcharge release voltage
Overdischarge detection voltage
Overdischarge release voltage
−
VDL ≠ VDU
VDL = VDU
VDIOV
−
−
−
Discharge overcurrent detection voltage
Load short-circuiting detection voltage
Charge overcurrent detection voltage
0 V Battery Charge Function
VSHORT
VCIOV
0 V battery charge function
"available"
V0CHA
0.0
0.6
0.7
0.8
1.0
1.1
V
V
0 V battery charge starting charger voltage
2
2
0 V battery charge function
"unavailable"
0 V battery charge inhibition battery
voltage
V0INH
Internal Resistance
RVMD
RVMS
VDD = 1.8 V, VVM = 0 V
VDD = 3.4 V, VVM = 1.0 V
kΩ
kΩ
Resistance between VM pin and VDD pin
Resistance between VM pin and VSS pin
Input Voltage
100
10
300
20
900
40
3
3
Operation voltage between VDD pin and
VSS pin
VDSOP1
VDSOP2
1.5
1.5
−
−
6.5
28
V
V
−
−
−
−
Operation voltage between VDD pin and
VM pin
Input Current (With Power-down Function)
IOPE
IPDN
VDD = 3.4 V, VVM = 0 V
VDD = VVM = 1.5 V
1.0
2.8
5.0
0.1
μA
μA
2
2
Current consumption during operation
Current consumption during power-down
−
−
Input Current (Without Power-down Function)
IOPE
VDD = 3.4 V, VVM = 0 V
VDD = VVM = 1.5 V
1.0
2.8
5.0
3.5
μA
μA
2
2
Current consumption during operation
Current consumption during overdischarge
Output Resistance
IOPED
−
−
V
V
V
V
V
V
V
V
CO = 3.0 V, VDD = 3.4 V,
VM = 0 V
RCOH
RCOL
RDOH
RDOL
5
5
5
5
10
10
10
10
20
20
20
20
kΩ
kΩ
kΩ
kΩ
CO pin resistance "H"
CO pin resistance "L"
DO pin resistance "H"
DO pin resistance "L"
4
4
4
4
CO = 0.4 V, VDD = 4.6 V,
VM = 0 V
DO = 3.0 V, VDD = 3.4 V,
VM = 0 V
DO = 0.4 V, VDD = 1.8 V,
VM = 0 V
Delay Time
tCU
tCU × 0.8
tDL × 0.8
tDIOV × 0.8
tSHORT × 0.8
tCIOV × 0.8
tCU
tDL
tCU × 1.2
tDL × 1.2
tDIOV × 1.2
tSHORT × 1.2
tCIOV × 1.2
−
−
−
−
−
Overcharge detection delay time
Overdischarge detection delay time
Discharge overcurrent detection delay time
Load short-circuiting detection delay time
Charge overcurrent detection delay time
−
−
−
−
−
5
5
5
5
5
tDL
tDIOV
tSHORT
tCIOV
tDIOV
tSHORT
tCIOV
*1. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by
design, not tested in production.
8
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
2. Ta = −40°C to +85°C*1
Table 10
(Ta = −40°C to +85°C*1 unless otherwise specified)
Test
Circuit
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Detection Voltage
VCU
VCL
VDL
VDU
−
VCU − 0.045
VCL − 0.070
VCL − 0.050
VDL − 0.070
VDU − 0.090
VDU − 0.070
VDIOV − 0.010 VDIOV VDIOV + 0.010
VSHORT − 0.100 VSHORT VSHORT + 0.100
VCIOV − 0.015 VCIOV VCIOV + 0.015
VCU
VCL
VCL
VDL
VDU
VDU
VCU + 0.030
VCL + 0.040
VCL + 0.030
VDL + 0.045
VDU + 0.060
VDU + 0.045
V
V
V
V
V
V
V
V
V
1
1
1
2
2
2
2
2
2
Overcharge detection voltage
VCL ≠ VCU
VCL = VCU
Overcharge release voltage
Overdischarge detection voltage
Overdischarge release voltage
−
VDL ≠ VDU
VDL = VDU
VDIOV
−
−
−
Discharge overcurrent detection voltage
Load short-circuiting detection voltage
Charge overcurrent detection voltage
0 V Battery Charge Function
VSHORT
VCIOV
0 V battery charge
function "available"
0 V battery charge
function "unavailable"
V0CHA
0.0
0.4
0.7
0.8
1.5
1.3
V
V
0 V battery charge starting charger voltage
2
2
0 V battery charge inhibition battery
voltage
V0INH
Internal Resistance
RVMD
RVMS
VDD = 1.8 V, VVM = 0 V
VDD = 3.4 V, VVM = 1.0 V
kΩ
kΩ
Resistance between VM pin and VDD pin
Resistance between VM pin and VSS pin
Input Voltage
78
7.2
300
20
1310
44
3
3
Operation voltage between VDD pin and
VSS pin
VDSOP1
VDSOP2
1.5
1.5
−
−
6.5
28
V
V
−
−
−
−
Operation voltage between VDD pin and
VM pin
Input Current (With Power-down Function)
IOPE
IPDN
VDD = 3.4 V, VVM = 0 V
VDD = VVM = 1.5 V
0.7
2.8
5.5
μA
μA
2
2
Current consumption during operation
Current consumption during power-down
−
−
0.15
Input Current (Without Power-down Function)
IOPE
VDD = 3.4 V, VVM = 0 V
VDD = VVM = 1.5 V
0.7
2.8
5.5
3.8
μA
μA
2
2
Current consumption during operation
Current consumption during overdischarge
Output Resistance
IOPED
−
−
V
V
V
V
V
V
V
V
CO = 3.0 V, VDD = 3.4 V,
VM = 0 V
RCOH
RCOL
RDOH
RDOL
2.4
2.4
2.4
2.4
10
10
10
10
30
30
30
30
kΩ
kΩ
kΩ
kΩ
CO pin resistance "H"
CO pin resistance "L"
DO pin resistance "H"
DO pin resistance "L"
4
4
4
4
CO = 0.4 V, VDD = 4.6 V,
VM = 0 V
DO = 3.0 V, VDD = 3.4 V,
VM = 0 V
DO = 0.4 V, VDD = 1.8 V,
VM = 0 V
Delay Time
tCU
tCU × 0.6
tDL × 0.6
tDIOV × 0.6
tSHORT × 0.6
tCIOV × 0.6
tCU
tDL
tCU × 1.6
tDL × 1.6
tDIOV × 1.6
tSHORT × 1.6
tCIOV × 1.6
−
−
−
−
−
Overcharge detection delay time
Overdischarge detection delay time
Discharge overcurrent detection delay time
Load short-circuiting detection delay time
Charge overcurrent detection delay time
−
−
−
−
−
5
5
5
5
5
tDL
tDIOV
tSHORT
tCIOV
tDIOV
tSHORT
tCIOV
*1. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by
design, not tested in production.
9
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Test Circuits
Caution Unless otherwise specified, the output voltage levels "H" and "L" at CO pin (VCO) and DO pin (VDO) are
judged by the threshold voltage (1.0 V) of the N-channel FET. Judge the CO pin level with respect to VVM
and the DO pin level with respect to VSS
.
1. Overcharge detection voltage, overcharge release voltage
(Test circuit 1)
Overcharge detection voltage (VCU) is defined as the voltage V1 at which VCO goes from "H" to "L" when the voltage V1
is gradually increased from the starting condition of V1 = 3.4 V. Overcharge release voltage (VCL) is defined as the
voltage V1 at which VCO goes from "L" to "H" when the voltage V1 is then gradually decreased. Overcharge hysteresis
voltage (VHC) is defined as the difference between VCU and VCL.
2. Overdischarge detection voltage, overdischarge release voltage
(Test circuit 2)
Overdischarge detection voltage (VDL) is defined as the voltage V1 at which VDO goes from "H" to "L" when the voltage
V1 is gradually decreased from the starting condition of V1 = 3.4 V, V2 = 0 V. Overdischarge release voltage (VDU) is
defined as the voltage V1 at which VDO goes from "L" to "H" when the voltage V1 is then gradually increased.
Overdischarge hysteresis voltage (VHD) is defined as the difference between VDU and VDL.
3. Discharge overcurrent detection voltage
(Test circuit 2)
Discharge overcurrent detection voltage (VDIOV) is defined as the voltage V2 whose delay time for changing VDO from
"H" to "L" is discharge overcurrent delay time (tDIOV) when the voltage V2 is increased from the starting condition of
V1 = 3.4 V, V2 = 0 V.
4. Load short-circuiting detection voltage
(Test circuit 2)
Load short-circuiting detection voltage (VSHORT) is defined as the voltage V2 whose delay time for changing VDO from
"H" to "L" is load short-circuiting delay time (tSHORT) when the voltage V2 is increased from the starting condition of
V1 = 3.4 V, V2 = 0 V.
5. Charge overcurrent detection voltage
(Test circuit 2)
Charge overcurrent detection voltage (VCIOV) is defined as the voltage V2 whose delay time for changing VCO from "H" to
"L" is charge overcurrent delay time (tCIOV) when the voltage V2 is decreased from the starting condition of V1 = 3.4 V,
V2 = 0 V.
6. Current consumption during operation
(Test circuit 2)
The current consumption during operation (IOPE) is the current that flows through the VDD pin (IDD) under the set
conditions of V1 = 3.4 V and V2 = 0 V.
7. Current consumption during power-down, current consumption during overdischarge
(Test circuit 2)
7. 1 With power-down function
The current consumption during power-down (IPDN) is IDD under the set conditions of V1 = V2 = 1.5 V.
7. 2 Without power-down function
The current consumption during overdischarge (IOPED) is IDD under the set conditions of V1 = V2 = 1.5 V.
10
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
8. Resistance between VM pin and VDD pin
(Test circuit 3)
RVMD is the resistance between VM pin and VDD pin under the set conditions of V1 = 1.8 V, V2 = 0 V.
9. Resistance between VM pin and VSS pin
(Test circuit 3)
RVMS is the resistance between VM pin and VSS pin under the set conditions of V1 = 3.4 V, V2 = 1.0 V.
10. CO pin resistance "H"
(Test circuit 4)
The CO pin resistance "H" (RCOH) is the resistance between VDD pin and CO pin under the set conditions of V1 = 3.4 V,
V2 = 0 V, V3 = 3.0 V.
11. CO pin resistance "L"
(Test circuit 4)
The CO pin resistance "L" (RCOL) is the resistance between VM pin and CO pin under the set conditions of V1 = 4.6 V,
V2 = 0 V, V3 = 0.4 V.
12. DO pin resistance "H"
(Test circuit 4)
The DO pin resistance "H" (RDOH) is the resistance between VDD pin and DO pin under the set conditions of V1 = 3.4 V,
V2 = 0 V, V4 = 3.0 V.
13. DO pin resistance "L"
(Test circuit 4)
The DO pin resistance "L" (RDOL) is the resistance between VSS pin and DO pin under the set conditions of V1 = 1.8 V,
V2 = 0 V, V4 = 0.4 V.
14. Overcharge detection delay time
(Test circuit 5)
The overcharge detection delay time (tCU) is the time needed for VCO to go to "L" just after the voltage V1 increases and
exceeds VCU under the set conditions of V1 = 3.4 V, V2 = 0 V.
15. Overdischarge detection delay time
(Test circuit 5)
The overdischarge detection delay time (tDL) is the time needed for VDO to go to "L" after the voltage V1 decreases and
falls below VDL under the set conditions of V1 = 3.4 V, V2 = 0 V.
16. Discharge overcurrent detection delay time
(Test circuit 5)
The discharge overcurrent detection delay time (tDIOV) is the time needed for VDO to go to "L" after the voltage V2
increases and exceeds VDIOV under the set conditions of V1 = 3.4 V, V2 = 0 V.
11
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
17. Load short-circuiting detection delay time
(Test circuit 5)
The load short-circuiting detection delay time (tSHORT) is the time needed for VDO to go to "L" after the voltage V2
increases and exceeds VSHORT under the set conditions of V1 = 3.4 V, V2 = 0 V.
18. Charge overcurrent detection delay time
(Test circuit 5)
The charge overcurrent detection delay time (tCIOV) is the time needed for VCO to go to "L" after the voltage V2
decreases and falls below VCIOV under the set conditions of V1 = 3.4 V, V2 = 0 V.
19. 0 V battery charge starting charger voltage (0 V battery charge function "available")
(Test circuit 2)
The 0 V charge starting charger voltage (V0CHA) is defined as the absolute value of voltage V2 at which VCO goes to
"H" (VCO = VDD) when the voltage V2 is gradually decreased from the starting conditions of V1 = V2 = 0 V.
20. 0 V battery charge inhibition battery voltage (0 V battery charge function "unavailable")
(Test circuit 2)
The 0 V charge inhibition battery voltage (V0INH) is defined as the voltage V1 at which VCO goes to "H" (VCO = VDD
)
when the voltage V1 is gradually increased, after setting V1 = 0 V, V2 = −4.0 V.
12
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
IDD
R1 = 330 Ω
VDD
VSS
VDD
VSS
A
V1
S-8200A Series
S-8200A Series
V1
C1
VM
VM
DO
CO
DO
CO
= 0.1 μF
V2
V VDO
V VCO
V VDO
V VCO
COM
COM
Figure 5 Test Circuit 1
Figure 6 Test Circuit 2
IDD
VDD
A
VDD
V1
V1
S-8200A Series
S-8200A Series
VSS
VM
VSS
VM
DO
CO
DO
A
CO
A
A IVM
V2
IDO
V4
ICO
V3
V2
COM
COM
Figure 7 Test Circuit 3
Figure 8 Test Circuit 4
VDD
V1
S-8200A Series
VSS
VM
DO
CO
Oscilloscope Oscilloscope
V2
COM
Figure 9 Test Circuit 5
13
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Operation
Remark Refer to " Battery Protection IC Connection Example".
1. Normal status
The S-8200A Series monitors the voltage of the battery connected between the VDD pin and VSS pin, the voltage
between the VM pin and VSS pin to control charging and discharging. When the battery voltage is in the range from
overdischarge detection voltage (VDL) to overcharge detection voltage (VCU), and the VM pin voltage is in the range from
charge overcurrent detection voltage (VCIOV) to discharge overcurrent detection voltage (VDIOV), the S-8200A Series turns
both the charge and discharge control FETs on. This condition is called the normal status, and in this condition charging
and discharging can be carried out freely.
The resistance (RVMD) between the VM pin and VDD pin, and the resistance (RVMS) between the VM pin and VSS pin are
not connected in the normal status.
Caution When the battery is connected for the first time, the S-8200A Series may not be in the normal status. In
this case, short the VM pin and VSS pin, or set the VM pin voltage at the level of VCIOV or more and at
the level of VDIOV or less by connecting the charger. The S-8200A Series then becomes the normal
status.
2. Overcharge status
2. 1 VCL ≠ VCU (Product in which overcharge release voltage differs from overcharge detection voltage)
When the battery voltage becomes higher than VCU during charging in the normal status and detection continues for
the overcharge detection delay time (tCU) or longer, the S-8200A Series turns the charge control FEToff to stop
charging. This condition is called the overcharge status.
RVMD and RVMS are not connected in the overcharge status.
The overcharge status is released in the following two cases.
(1) In the case that the VM pin voltage is lower than VDIOV, the S-8200A Series releases the overcharge status when
the battery voltage falls below overcharge release voltage (VCL).
(2) In the case that the VM pin voltage is higher than or equal to VDIOV, the S-8200A Series releases the overcharge
status when the battery voltage falls below VCU
.
When the discharge is started by connecting a load after the overcharge detection, the VM pin voltage rises by the Vf
voltage of the parasitic diode than the VSS pin voltage, because the discharge current flows through the parasitic
diode in the charge control FET. If this VM pin voltage is higher than or equal to VDIOV, the S-8200A Series releases
the overcharge status when the battery voltage is lower than or equal to VCU
.
Caution If the battery is charged to a voltage higher than VCU and the battery voltage does not fall below VCU
even when a heavy load is connected, discharge overcurrent detection and load short-circuiting
detection do not function until the battery voltage falls below VCU. Since an actual battery has an
internal impedance of tens of mΩ, the battery voltage drops immediately after a heavy load that
causes overcurrent is connected, and discharge overcurrent detection and load short-circuiting
detection function.
14
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
2. 2 VCL = VCU (Product in which overcharge release voltage is the same as overcharge detection voltage)
When the battery voltage becomes higher than VCU during charging in the normal status and detection continues for
tCU or longer, the S-8200A Series turns the charge control FET off to stop charging. This condition is called the
overcharge status.
RVMD and RVMS are not connected in the overcharge status.
The overcharge status is released in the following two cases.
(1) In the case that the VM pin voltage is higher than or equal to VCIOV, and is lower than VDIOV, the S-8200A Series
releases the overcharge status when the battery voltage falls below VCL.
(2) In the case that the VM pin voltage is higher than or equal to VDIOV, the S-8200A Series releases the overcharge
status when the battery voltage falls below VCU
.
When the discharge is started by connecting a load after the overcharge detection, the VM pin voltage rises by the Vf
voltage of the parasitic diode than the VSS pin voltage, because the discharge current flows through the parasitic
diode in the charging control FET. If this VM pin voltage is higher than or equal to VDIOV, the S-8200A Series releases
the overcharge status when the battery voltage is lower than or equal to VCU
.
For the actual application boards, changing the battery voltage and the charger voltage simultaneously enables to
measure VCL. In this case, the charger is always necessary to have the equivalent voltage level to the battery
voltage. The charger keeps VM pin voltage higher than or equal to VCIOV and lower than or equal to VDIOV. The
S-8200A Series releases the overcharge status when the battery voltage falls below VCL.
Caution 1. If the battery is charged to a voltage higher than VCU and the battery voltage does not fall below VCU
even when a heavy load is connected, discharge overcurrent detection and load short-circuiting
detection do not function until the battery voltage falls below VCU. Since an actual battery has an
internal impedance of tens of mΩ, the battery voltage drops immediately after a heavy load that
causes overcurrent is connected, and discharge overcurrent detection and load short-circuiting
detection function.
2. When a charger is connected after overcharge detection, the overcharge status is not released
even if the battery voltage is below VCL. The overcharge status is released when the VM pin voltage
goes over VCIOV by removing the charger.
3. Overdischarge status
When the battery voltage falls below overdischarge detection voltage (VDL) during discharging in the normal status and
the detection continues for the overdischarge detection delay time (tDL) or longer, the S-8200A Series turns the discharge
control FET off to stop discharging. This condition is called the overdischarge status.
Under the overdischarge status, the VM pin and VDD pin are shorted by RVMD in the S-8200A Series. The VM pin
voltage is pulled up by RVMD
.
When a battery in the overdischarge status is connected to a charger and provided that the VM pin voltage is lower than
−0.7 V typ., the S-8200A Series releases the overdischarge status when the battery voltage reaches VDL or higher.
When VM pin voltage is not lower than −0.7 V typ., the S-8200A Series releases the overdischarge status when the
battery voltage reaches VDU or higher.
RVMS is not connected in the overdischarge status.
3. 1 With power-down function
Under the overdischarge status, when voltage between the VDD pin and VM pin is 0.8 V typ. or lower, the power-
down function works and the current consumption is reduced to the current consumption during power-down (IPDN).
By connecting a battery charger, the power-down function is released when the VM pin voltage is 0.7 V typ. or lower.
15
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
4. Discharge overcurrent status (discharge overcurrent, load short-circuiting)
When a battery in the normal status is in the status where the VM pin voltage is equal to or higher than VDIOV because
the discharge current is equal to or higher than the specified value and the status lasts for the discharge overcurrent
detection delay time (tDIOV), the discharge control FET is turned off and discharging is stopped. This status is called the
discharge overcurrent status.
In the discharge overcurrent status, the VM pin and VSS pin are shorted by the RVMS in the S-8200A Series. However,
the VM pin voltage is the VDD pin voltage due to the load as long as the load is connected. When the load is
disconnected, the VM pin returns to the VSS pin voltage.
The VM pin voltage returns to VDIOV or lower, the S-8200A Series releases the discharge overcurrent status.
RVMD is not connected in the discharge overcurrent status.
5. Charge overcurrent status
When a battery in the normal status is in the status where the VM pin voltage is equal to or lower than VCIOV because the
charge current is equal to or higher than the specified value and the status lasts for the charge overcurrent detection
delay time (tCIOV), the charge control FET is turned off and charging is stopped. This status is called the charge
overcurrent status.
The S-8200A Series releases the charge overcurrent status when the VM pin voltage returns to VCIOV or higher by
removing the charger.
The charge overcurrent detection function does not work in the overdischarge status.
RVMD and RVMS are not connected in the charge overcurrent status.
6. 0 V battery charge function "available"
This function is used to recharge a connected battery whose voltage is 0 V due to self-discharge. When the 0 V battery
charge starting charger voltage (V0CHA) or a higher voltage is applied between the EB+ and EB− pins by connecting a
charger, the charge control FET gate is fixed to the VDD pin voltage.
When the voltage between the gate and source of the charge control FET becomes equal to or higher than the threshold
voltage due to the charger voltage, the charge control FET is turned on to start charging. At this time, the discharge
control FET is off and the charging current flows through the internal parasitic diode in the discharging control FET.
When the battery voltage becomes equal to or higher than VDU, the S-8200A Series enters the normal status.
Caution 1. Some battery providers do not recommend charging for a completely self-discharged battery.
Please ask the battery provider to determine whether to enable or inhibit the 0 V battery charge
function.
2. The 0 V battery charge function has higher priority than the charge overcurrent detection function.
Consequently, a product in which use of the 0 V battery charge function is enabled charges a
battery forcibly and the charge overcurrent cannot be detected when the battery voltage is lower
than VDL
.
7. 0 V battery charge function "unavailable"
This function inhibits recharging when a battery that is internally short-circuited (0 V battery) is connected. When the
battery voltage is the 0 V battery charge inhibition battery voltage (V0INH) or lower, the charge control FET gate is fixed to
the EB− pin voltage to inhibit charging. When the battery voltage is V0INH or higher, charging can be performed.
Caution Some battery providers do not recommend charging for a completely self-discharged battery. Please
ask the battery provider to determine whether to enable or inhibit the 0 V battery charge function.
16
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
8. Delay circuit
The detection delay times are determined by dividing a clock of approximately 4 kHz by the counter.
Remark tDIOV and tSHORT start when VDIOV is detected. When VSHORT is detected over tSHORT after VDIOV, the S-8200A
Series turns the discharge control FET off within tSHORT from the time of detecting VSHORT
.
VDD
DO pin voltage
tD
0 ≤ tD ≤ tSHORT
VSS
Time
tSHORT
VDD
VSHORT
VM pin voltage
VDIOV
VSS
Time
Figure 10
17
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Timing Charts
1. Overcharge detection, overdischarge detection
VCU
V
CL (VCU − VHC
)
Battery voltage
V
DU (VDL + VHD
VDL
)
VDD
DO pin voltage
VSS
VDD
CO pin voltage
VSS
VEB
−
VDD
VM pin voltage
VDIOV
VSS
VCIOV
VEB
−
Charger connection
Load connection
Overcharge detection delay time (tCU)
(1) (2)
Overdischarge detection delay time (tDL)
(1) (3)
(1)
Status*1
*1. (1): Normal status
(2): Overcharge status
(3): Overdischarge status
Remark The charger is assumed to charge with a constant current.
Figure 11
18
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
2. Discharge overcurrent detection
VCU
V
CL (VCU − VHC
Battery voltage
VDU (VDL + VHD
)
)
VDL
VDD
DO pin voltage
VSS
VDD
CO pin voltage
VM pin voltage
VSS
VDD
VSHORT
VDIOV
VSS
Load connection
Discharge overcurrent
detection delay time (tDIOV
Load short-circuiting
detection delay time (tSHORT
)
)
(1)
(2)
(1) (2)
(1)
Status*1
*1. (1): Normal status
(2): Discharge overcurrent status
Remark The charger is assumed to charge with a constant current.
Figure 12
19
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
3. Charge overcurrent detection
VCU
VCL (VCU − VHC
)
Battery voltage
VDU (VDL + VHD
)
VDL
VDD
DO pin voltage
VSS
VDD
CO pin voltage
VM pin voltage
VSS
VEB
−
VDD
VSS
VCIOV
VEB
−
Charger connection
Load connection
Overdischarge detection
delay time (tDL)
Charge overcurrent detection
delay time (tCIOV
Charge overcurrent detection
)
delay time (tCIOV
(3)
(1)
)
(2)
(2)
(1)
(1)
Status*1
*1. (1): Normal status
(2): Charge overcurrent status
(3): Overdischarge status
Remark The charger is assumed to charge with a constant current.
Figure 13
20
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Battery Protection IC Connection Example
EB+
R1
VDD
Battery C1
S-8200A Series
CO
VSS
DO
VM
R2
FET1
FET2
EB−
Figure 14
Table 11 Constants for External Components
Symbol
FET1
Part
Purpose
Min.
Typ.
Max.
Remark
Threshold voltage ≤ Overdischarge
detection voltage*1
Gate to source withstand voltage ≥
Charger voltage*2
N-channel
MOS FET
Discharge control
−
−
−
Threshold voltage ≤ Overdischarge
detection voltage*1
Gate to source withstand voltage ≥
Charger voltage*2
N-channel
MOS FET
FET2
R1
Charge control
−
−
−
Resistance should be as small as
possible to avoid lowering the
overcharge detection accuracy due to
current consumption.*3
ESD protection,
For power fluctuation
Resistor
150 Ω
330 Ω
1 kΩ
Connect a capacitor of 0.068 μF or
higher between VDD pin and VSS pin.*4
Select as large a resistance as possible
to prevent current when a charger is
connected in reverse.*5
C1
R2
Capacitor For power fluctuation
Protection for reverse
0.068 μF
300 Ω
0.1 μF
2 kΩ
1.0 μF
4 kΩ
Resistor
connection of a
charger
*1. If the threshold voltage of an FET is low, the FET may not cut the charge current. If an FET with a threshold voltage equal
to or higher than the overdischarge detection voltage is used, discharging may be stopped before overdischarge is
detected.
*2. If the withstand voltage between the gate and source is lower than the charger voltage, the FET may be destroyed.
*3. An accuracy of overcharge detection voltage is guaranteed by R1 = 330 Ω. Connecting resistors with other values worsen
the accuracy. In case of connecting larger resistor to R1, the voltage between the VDD pin and VSS pin may exceed the
absolute maximum rating because the current flows to the S-8200A Series from the charger due to reverse connection of
charger. Connect a resistor of 150 Ω or more to R1 for ESD protection.
*4. When connecting a resistor of 150 Ω or less to R1 or a capacitor of 0.068 μF or less to C1, the S-8200A Series may
malfunction when power dissipation is largely fluctuated.
*5. When a resistor more than 4 kΩ is connected to R2, the charge current may not be cut.
Caution 1. The above constants may be changed without notice.
2. It has not been confirmed whether the operation is normal or not in circuits other than the above example
of connection. In addition, the example of connection shown above and the constant do not guarantee
proper operation. Perform thorough evaluation using the actual application to set the constant.
21
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Precautions
• The application conditions for the input voltage, output voltage, and load current should not exceed the package power
dissipation.
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
• SII Semiconductor Corporation claims no responsibility for any and all disputes arising out of or in connection with any
infringement by products including this IC of patents owned by a third party.
22
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Characteristics (Typical Data)
1. Current consumption
1. 1 IOPE vs. Ta
1. 2 IPDN vs. Ta
6
5
4
3
2
1
0
0.100
0.075
0.050
0.025
0
−40 −25
0
25
50
75 85
0
25
50
75 85
Ta [°C]
Ta [°C]
1. 3 IOPE vs. VDD
6
5
4
3
2
1
0
0
1
2
3
4
5
6
7
VDD [V]
23
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
2. Overcharge detection / release voltage, overdischarge detection / release voltage,
overcurrent detection voltage, charge overcurrent detection voltage, and delay time
2. 1 VCU vs. Ta
2. 2 VCL vs. Ta
4.26
4.07
4.05
4.03
4.01
3.99
3.97
3.95
4.24
4.22
4.20
4.18
−40 −25
0
0
0
0
25
50
50
50
50
75 85
75 85
75 85
75 85
−40 −25
0
0
0
25
50
50
50
75 85
75 85
75 85
4.5
Ta [°C]
Ta [°C]
2. 3 VDL vs. Ta
2. 4 VDU vs. Ta
2.55
2.53
2.51
2.49
2.47
2.45
2.43
2.96
2.92
2.88
2.84
2.80
−40 −25
25
−40 −25
25
Ta [°C]
Ta [°C]
2. 5 tCU vs. Ta
2. 6 tDL vs. Ta
1.6
1.4
1.2
1.0
0.8
0.6
110
90
70
50
30
−40 −25
25
−40 −25
25
Ta [°C]
Ta [°C]
2. 7 VDIOV vs. Ta
2. 8 tDIOV vs. VDD
0.160
14
12
10
8
0.155
0.150
0.145
0.140
6
4
−40 −25
25
2.5
3.0
3.5
4.0
Ta [°C]
VDD [V]
24
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
2. 9 tDIOV vs. Ta
2. 10 VCIOV vs. Ta
−0.135
14
12
10
8
−0.140
−0.145
−0.150
−0.155
6
−0.160
4
−0.165
−40 −25
0
25
50
75 85
−40 −25
0
25
50
75 85
Ta [°C]
Ta [°C]
2. 11 tCIOV vs. VDD
2. 12 tCIOV vs. Ta
14
14
12
10
8
12
10
8
6
6
4
4
2.5
3.0
3.5
4.0
4.5
−40 −25
0
25
50
75 85
VDD [V]
Ta [°C]
2. 13 VSHORT vs. Ta
2. 14 tSHORT vs. VDD
0.60
400
350
300
250
200
0.55
0.50
0.45
0.40
150
2.5
−40 −25
0
25
50
75 85
3.0
3.5
4.0
4.5
Ta [°C]
VDD [V]
2. 15 tSHORT vs. Ta
400
350
300
250
200
150
−40 −25
0
25
50
75 85
Ta [°C]
25
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
3. CO pin / DO pin
3. 1 RCOH vs. VCO
3. 2 RCOL vs. VCO
20
20
15
10
5
15
10
5
0
1
2
3
4
0
1
2
3
4
5
VCO [V]
VCO [V]
3. 3 RDOH vs. VDO
3. 4 RDOL vs. VDO
20
20
15
10
15
10
5
0
5
0
1
2
3
4
0.5
1.0
VDO [V]
1.5
2.0
V
DO [V]
26
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
Marking Specifications
1. SOT-23-6
Top view
(1) to (3):
(4):
Product code (refer to Product name vs. Product code)
Lot number
6
5
4
(1) (2) (3) (4)
1
2
3
Product name vs. Product code
Product Code
Product Name
(1)
(2)
3
(3)
C
H
Y
S-8200AAC-M6T1U
S-8200AAH-M6T1U
S-8200AAY-M6T1U
S-8200ABE-M6T1U
S-8200ABM-M6T1U
S-8200ABX-M6T1U
S-8200ABZ-M6T1U
S-8200ACF-M6T1U
S-8200ACV-M6T1U
S-8200ACW-M6T1U
V
V
V
V
V
V
V
S
S
S
3
3
4
E
4
M
X
4
4
Z
Y
Y
Y
F
V
W
27
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8200A Series
Rev.4.0_02
2. SNT-6A
Top view
(1) to (3):
(4) to (6):
Product code (refer to Product name vs. Product code)
Lot number
6
5
4
(1) (2) (3)
(4) (5) (6)
1
2
3
Product name vs. Product code
Product Code
Product Name
(1)
(2)
3
(3)
A
B
C
D
F
S-8200AAA-I6T1U
S-8200AAB-I6T1U
S-8200AAC-I6T1U
S-8200AAD-I6T1U
S-8200AAF-I6T1U
S-8200AAG-I6T1U
S-8200AAH-I6T1U
S-8200ABA-I6T1U
S-8200ABI-I6T1U
S-8200ABK-I6T1U
S-8200ABL-I6T1U
S-8200ABM-I6T1U
S-8200ACN-I6T1U
S-8200ACO-I6T1U
S-8200ACP-I6T1U
S-8200ACQ-I6T1U
S-8200ACR-I6T1U
V
V
V
V
V
V
V
V
V
V
V
V
S
S
S
S
S
3
3
3
3
3
G
H
A
I
3
4
4
4
K
L
4
4
M
N
O
P
Q
R
Y
Y
Y
Y
Y
28
2.9±0.2
1.9±0.2
6
5
4
+0.1
-0.05
1
3
2
0.15
0.95
0.95
0.35±0.15
No. MP006-A-P-SD-2.0
SOT236-A-PKG Dimensions
MP006-A-P-SD-2.0
TITLE
No.
SCALE
UNIT
mm
SII Semiconductor Corporation
4.0±0.1(10 pitches:40.0±0.2)
+0.1
-0
2.0±0.05
0.25±0.1
ø1.5
+0.2
-0
4.0±0.1
ø1.0
1.4±0.2
3.2±0.2
3
4
2 1
6
5
Feed direction
No. MP006-A-C-SD-3.1
TITLE
SOT236-A-Carrier Tape
MP006-A-C-SD-3.1
No.
SCALE
UNIT
mm
SII Semiconductor Corporation
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP006-A-R-SD-2.1
SOT236-A-Reel
MP006-A-R-SD-2.1
TITLE
No.
SCALE
UNIT
3,000
QTY
mm
SII Semiconductor Corporation
1.57±0.03
6
5
4
+0.05
-0.02
0.08
1
2
3
0.5
0.48±0.02
0.2±0.05
No. PG006-A-P-SD-2.0
SNT-6A-A-PKG Dimensions
PG006-A-P-SD-2.0
TITLE
No.
SCALE
UNIT
mm
SII Semiconductor Corporation
+0.1
-0
ø1.5
4.0±0.1
2.0±0.05
0.25±0.05
+0.1
ø0.5
-0
4.0±0.1
0.65±0.05
1.85±0.05
5°
3
2
5
1
6
4
Feed direction
No. PG006-A-C-SD-1.0
TITLE
SNT-6A-A-Carrier Tape
PG006-A-C-SD-1.0
No.
SCALE
UNIT
mm
SII Semiconductor Corporation
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PG006-A-R-SD-1.0
SNT-6A-A-Reel
TITLE
PG006-A-R-SD-1.0
No.
SCALE
UNIT
QTY.
5,000
SII Semiconductor Corporation
0.52
2
1.36
0.52
1
0.3
0.2
1.
2.
(0.25 mm min. / 0.30 mm typ.)
(1.30 mm ~ 1.40 mm)
0.03 mm
SNT
1. Pay attention to the land pattern width (0.25 mm min. / 0.30 mm typ.).
2. Do not widen the land pattern to the center of the package ( 1.30 mm ~ 1.40 mm ).
Caution 1. Do not do silkscreen printing and solder printing under the mold resin of the package.
2. The thickness of the solder resist on the wire pattern under the package should be 0.03 mm
or less from the land pattern surface.
3. Match the mask aperture size and aperture position with the land pattern.
4. Refer to "SNT Package User's Guide" for details.
(0.25 mm min. / 0.30 mm typ.)
(1.30 mm ~ 1.40 mm)
1.
2.
SNT-6A-A
-Land Recommendation
TITLE
No. PG006-A-L-SD-4.1
No.
PG006-A-L-SD-4.1
SCALE
UNIT
mm
SII Semiconductor Corporation
Disclaimers (Handling Precautions)
1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
SII Semiconductor Corporation is not responsible for damages caused by the reasons other than the products or
infringement of third-party intellectual property rights and any other rights due to the use of the information described
herein.
3. SII Semiconductor Corporation is not responsible for damages caused by the incorrect information described herein.
4. Take care to use the products described herein within their specified ranges. Pay special attention to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
SII Semiconductor Corporation is not responsible for damages caused by failures and/or accidents, etc. that occur
due to the use of products outside their specified ranges.
5. When using the products described herein, confirm their applications, and the laws and regulations of the region or
country where they are used and verify suitability, safety and other factors for the intended use.
6. When exporting the products described herein, comply with the Foreign Exchange and Foreign Trade Act and all
other export-related laws, and follow the required procedures.
7. The products described herein must not be used or provided (exported) for the purposes of the development of
weapons of mass destruction or military use. SII Semiconductor Corporation is not responsible for any provision
(export) to those whose purpose is to develop, manufacture, use or store nuclear, biological or chemical weapons,
missiles, or other military use.
8. The products described herein are not designed to be used as part of any device or equipment that may affect the
human body, human life, or assets (such as medical equipment, disaster prevention systems, security systems,
combustion control systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment,
aviation equipment, aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle
use or other uses. Do not use those products without the prior written permission of SII Semiconductor Corporation.
Especially, the products described herein cannot be used for life support devices, devices implanted in the human
body and devices that directly affect human life, etc.
Prior consultation with our sales office is required when considering the above uses.
SII Semiconductor Corporation is not responsible for damages caused by unauthorized or unspecified use of our
products.
9. Semiconductor products may fail or malfunction with some probability.
The user of these products should therefore take responsibility to give thorough consideration to safety design
including redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing
injury or death, fires and social damage, etc. that may ensue from the products' failure or malfunction.
The entire system must be sufficiently evaluated and applied on customer's own responsibility.
10. The products described herein are not designed to be radiation-proof. The necessary radiation measures should be
taken in the product design by the customer depending on the intended use.
11. The products described herein do not affect human health under normal use. However, they contain chemical
substances and heavy metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips
may be sharp. Take care when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products described herein, comply with the laws and ordinances of the country or region where
they are used.
13. The information described herein contains copyright information and know-how of SII Semiconductor Corporation.
The information described herein does not convey any license under any intellectual property rights or any other
rights belonging to SII Semiconductor Corporation or a third party. Reproduction or copying of the information
described herein for the purpose of disclosing it to a third-party without the express permission of SII Semiconductor
Corporation is strictly prohibited.
14. For more details on the information described herein, contact our sales office.
1.0-2016.01
www.sii-ic.com
相关型号:
©2020 ICPDF网 联系我们和版权申明