S-8232NNFT-T2-G 概述
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK 电池保护IC 2串联用电池组
S-8232NNFT-T2-G 数据手册
通过下载S-8232NNFT-T2-G数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Rev.5.4_00
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
The 8232 series is a lithium-ion / lithium-polymer
rechargeable battery protection IC incorporating high-
accuracy voltage detection circuit and delay circuit.
The S-8232 series is suitable for 2-cell serial lithium-ion
/ lithium-polymer battery packs.
Features
(1) Internal high-accuracy voltage detection circuit
• Overcharge detection voltage
3.85 V 25 mV to 4.60 V 25 mV
3.60 V 50 mV to 4.60 V 50 mV
Applicable in 5 mV step
Applicable in 5 mV step
• Overcharge release voltage
(The overcharge release voltage can be selected within the range where a difference from overcharge
detection voltage is 0 to 0.3 V.)
• Overdischarge detection voltage 1.70 V 80 mV to 2.60 V 80 mV
Applicable in 50 mV step
• Overdischarge release voltage
1.70 V 100 mV to 3.80 V 100 mV Applicable in 50 mV step
(The overdischarge release voltage can be selected within the range where a difference from
overdischarge detection voltage is 0 to 1.2 V.)
• Overcurrent detection voltage 1 0.07 V 20 mV to 0.30 V 20 mV
(2) High input-voltage device : Absolute maximum ratings 18 V.
(3) Wide operating voltage range : 2 to 16 V
Applicable in 5 mV step
(4) The delay time for every detection can be set via an external capacitor.
(Each delay time for Overcharge detection, Overdischarge detection, Overcurrent detection are
“Proportion of hundred to ten to one”.)
(5) Two overcurrent detection levels (Protection for short-circuiting)
(6) Internal auxiliary over voltage detection circuit (Fail-safe for overcharge detection voltage)
(7) Internal charge circuit for 0 V battery (Unavailable is option)
(8) Low current consumption
• Operation mode
7.5 µA typ. 14.2 µA max. (− 40 to + 85 °C)
• Power-down mode 0.2 nA typ. 0.1 µA max. (− 40 to + 85 °C)
(9) Lead-free products
Application
• Lithium-ion rechargeable battery packs
• Lithium- polymer rechargeable battery packs
Package
Package Name
Drawing Code
Package
FT008-A
Tape
Reel
FT008-E
8-Pin TSSOP
FT008-E
Seiko Instruments Inc.
1
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Block Diagram
VCC
Reference
voltage 1
SENS
Auxiliary
overcharge
detector 1
−
+
Overcharge
detector 1
−
+
Over-
DO
Delay circuit
control signal
discharge
detector 1
−
+
Control
logic
VC
CO
Over-
discharge
detector 2
RCOL
+
−
Overcharge
detector 2
Over current
+
−
VM
detection circuit
Delay circuit control signal
Delay circuit
Delay circuit
control signal
+
−
control signal
Auxiliary
Delay circuit
overcharge
detector 2
ICT
Reference
voltage 2
VSS
DO, CO control signal
Remark Resistor (RCOL) is connected to the Nch transistor although CO pin serves as a CMOS output.
For this, impedance becomes high when outputting “L” from CO pin. Refer to the “ Electrical
Characteristics” for the impedance value.
Figure 1
2
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Product Name Structure
1. Product Name
S-8232 xx FT - T2 - G
IC direction in tape specifications *1
Package code
FT : 8-Pin TSSOP
Serial code
Sequentially set from AA to ZZ
*1. Refer to the taping specifications.
2. Product Name List
Table 1 (1 / 2)
Overcharge
detection
delay time
tCU
Overcharge
Overcharge
detection
voltage 1, 2
VCU
Overdischarge
detection
voltage 1, 2
VDD
Overdischarge
Overcurrent
detection
voltage 1
VIOV1
0 V battery
charging
function
release
voltage1, 2
VDU
Product name / Item
release voltage 1, 2
VCD
(C3 = 0.22 µF)
S-8232AAFT-T2-G 4.25 V 25 mV
S-8232ABFT-T2-G 4.35 V 25 mV
S-8232ACFT-T2-G 4.35 V 25 mV
S-8232AEFT-T2-G 4.35 V 25 mV
S-8232AFFT-T2-G 4.25 V 25 mV
S-8232AGFT-T2-G 4.25 V 25 mV
S-8232AHFT-T2-G 4.25 V 25 mV
4.05 V 50 mV
4.15 V 50 mV
4.15 V 50 mV
4.28 V 50 mV
4.05 V 50 mV
4.05 V 50 mV
4.05 V 50 mV
2.40 V 80 mV 3.00 V 100 mV 0.150 V 20 mV
2.30 V 80 mV 3.00 V 100 mV 0.300 V 20 mV
2.30 V 80 mV 3.00 V 100 mV 0.300 V 20 mV
2.15 V 80 mV 2.80 V 100 mV 0.100 V 20 mV
2.30 V 80 mV 2.70 V 100 mV 0.300 V 20 mV
2.20 V 80 mV 2.40 V 100 mV 0.200 V 20 mV
2.20 V 80 mV 2.40 V 100 mV 0.300 V 20 mV
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
Available
Available
Unavailable
Available
Available
Available
Available
S-8232AIFT-T2-G 4.325 V 25 mV 4.325 V 25 mV *1 *2 2.40 V 80 mV 3.00 V 100 mV 0.300 V 20 mV
Unavailable
Unavailable
Available
Available
Available
Unavailable
Available
Unavailable
Unavailable
Unavailable
Available
Unavailable
Available
Unavailable
Unavailable
Available
S-8232AJFT-T2-G 4.25 V 25 mV
S-8232AKFT-T2-G 4.20 V 25 mV
S-8232ALFT-T2-G 4.30 V 25 mV
S-8232AMFT-T2-G 4.19 V 25 mV
4.05 V 50 mV
4.00 V 50 mV
4.05 V 50 mV
4.19 V 25 mV *1
2.40 V 80 mV 3.00 V 100 mV 0.150 V 20 mV
2.30 V 80 mV 2.90 V 100 mV 0.200 V 20 mV
2.00 V 80 mV 3.00 V 100 mV 0.200 V 20 mV
2.00 V 80 mV 3.00 V 100 mV 0.190 V 20 mV
S-8232ANFT-T2-G 4.325 V 25 mV 4.325 V 25 mV *1 *3 2.40 V 80 mV 3.00 V 100 mV 0.300 V 20 mV
S-8232AOFT-T2-G 4.30 V 25 mV
S-8232APFT-T2-G 4.28 V 25 mV
4.05 V 50 mV
4.05 V 50 mV
2.00 V 80 mV 3.00 V 100 mV 0.230 V 20 mV
2.30 V 80 mV 2.90 V 100 mV 0.100 V 20 mV
S-8232ARFT-T2-G 4.325 V 25 mV 4.325 V 25 mV *1 *3 2.00 V 80 mV 2.50 V 100 mV 0.300 V 20 mV
S-8232ASFT-T2-G*4 4.295 V 25 mV 4.20 V 50 mV *3
2.30 V 80 mV 3.00 V 100 mV 0.300 V 20 mV
S-8232ATFT-T2-G 4.125 V 25 mV 4.125 V 25 mV *1 2.00 V 80 mV 3.00 V 100 mV 0.190 V 20 mV
S-8232AUFT-T2-G 4.30 V 25 mV
S-8232AVFT-T2-G 4.30 V 25 mV
S-8232AWFT-T2-G 4.35 V 25 mV
S-8232AXFT-T2-G 4.325 V 25 mV 4.200 V 50 mV
S-8232AYFT-T2-G 4.30 V 25 mV
S-8232AZFT-T2-G 4.30 V 25 mV
4.10 V 50 mV
4.05 V 50 mV
4.15 V 50 mV
2.40 V 80 mV 3.00 V 100 mV 0.200 V 20 mV
2.00 V 80 mV 3.00 V 100 mV 0.300 V 20mV
2.30 V 80 mV 3.00 V 100 mV 0.150 V 20 mV
2.30 V 80 mV 3.00 V 100 mV 0.20 V 20 mV
4.05 V 50 mV
4.05 V 50 mV
2.00 V 80 mV 2.00 V 80 mV
2.30 V 80 mV 2.30 V 80 mV
0.20 V 20 mV
0.20 V 20 mV
Available
Seiko Instruments Inc.
3
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Table 1 (2 / 2)
Overcharge
Overcharge
detection
voltage 1, 2
VCU
Overdischarge
detection
voltage 1, 2
VDD
Overdischarge
release
voltage1, 2
VDU
Overcurrent
detection
voltage 1
VIOV1
Overcharge
release voltage 1, 2
VCD
detection
delay time
tCU
0 V battery
charging
function
Product name / Item
(C3 = 0.22 µF)
S-8232NAFT-T2-G 4.325 V 25 mV 4.325 V 25 mV *1 *3 2.40 V 80 mV 3.00 V 100 mV 0.15 V 20 mV
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
1.0 s
Unavailable
Unavailable
Unavailable
Available
Available
Unavailable
Available
Unavailable
Unavailable
Available
Available
Available
S-8232NBFT-T2-G 4.35 V 25 mV
S-8232NCFT-T2-G 4.275 V 25 mV
S-8232NDFT-T2-G 4.35 V 25 mV
S-8232NEFT-T2-G 4.35 V 25 mV
S-8232NFFT-T2-G 4.325 V 25 mV
S-8232NGFT-T2-G 4.35 V 25 mV
S-8232NHFT-T2-G 4.28 V 25 mV
4.25 V 25 mV
4.28 V 25 mV
S-8232NKFT-T2-G 4.35 V 25 mV
S-8232NLFT-T2-G 4.30 V 25 mV
4.25 V 50 mV
4.05 V 50 mV
4.15 V 50 mV
4.15 V 50 mV
4.1 V 50 mV *3
4.15 V 50 mV
4.05 V 50 mV
4.05 V 50 mV *3
4.05 V 50 mV
4.15 V 50 mV
4.05 V 50 mV
4.05 V 50 mV
4.08 V 50 mV *3
3.00 V 80 mV 3.70 V 100 mV 0.30 V 20 mV
2.20 V 80 mV 3.00 V 100 mV 0.20 V 20 mV
2.30 V 80 mV 2.30 V 80 mV 0.15 V 20 mV
2.30 V 80 mV 3.00 V 100 mV 0.23 V 20 mV
2.30 V 80 mV 2.90 V 100 mV 0.21 V 20 mV
2.60 V 80 mV 3.00 V 100 mV 0.30 V 20 mV
2.30 V 80 mV 2.90 V 100 mV 0.11 V 20 mV
2.50 V 80 mV 3.00 V 100 mV 0.15 V 20 mV
2.30 V 80 mV 2.90 V 100 mV 0.11 V 20 mV
2.30 V 80 mV 2.30 V 80 mV 0.12 V 20 mV
2.30 V 80 mV 3.00 V 100 mV 0.23 V 20 mV
2.30 V 80 mV 2.90 V 100 mV 0.08 V 20 mV
2.20 V 80 mV 2.40 V 100 mV 0.13 V 20 mV
S-8232NIFT-T2-G
S-8232NJFT-T2-G
S-8232NMFT-T2-G 4.28 V 25 mV
S-8232NNFT-T2-G 4.28 V 25 mV
Available
Unavailable
Unavailable
Unavailable
Unavailable
Unavailable
Unavailable
Unavailable
Available
S-8232NOFT-T2-G 4.295 V 25 mV 4.045 V 50 mV *3 2.20 V 80 mV 2.40 V 100 mV 0.13 V 20 mV
S-8232NPFT-T2-G 4.25 V 25 mV
S-8232NQFT-T2-G 4.25 V 25 mV
S-8232NRFT-T2-G 4.15 V 25 mV
S-8232NSFT-T2-G 4.15 V 25 mV
S-8232NTFT-T2-G 4.225 V 25 mV
S-8232NUFT-T2-G 3.85 V 25 mV
4.05 V 50 mV
4.05 V 50 mV
3.95 V 50 mV
3.95 V 50 mV
4.15 V 50 mV
2.30 V 80 mV 3.00 V 100 mV 0.30 V 20 mV
2.60 V 80 mV 3.00 V 100 mV 0.30 V 20 mV
2.60 V 80 mV 3.00 V 100 mV 0.30 V 20 mV
2.30 V 80 mV 3.00 V 100 mV 0.30 V 20 mV
2.00 V 80 mV 2.00 V 100 mV 0.09 V 20 mV
2.23 V 80 mV 2.23 V 80 mV 0.15 V 20 mV
2.00 V 80 mV 2.00 V 80 mV 0.09 V 20 mV
3.75 V 50 mV
S-8232NWFT-T2-G
Unavailable
4.210 V 25 mV 4.125 V 50 mV
*1. No overcharge detection / release hysteresis
*2. The magnification of final overcharge is 1.11; the others are 1.25.
*3. No final overcharging function
*4. Refer to the *2 in the “ Operation”.
Remark 1. Please contact our sales office for the products with detection voltage value other than those
specified above.
2. The overdischarge detection voltage can be selected within the range from 1.7 to 3.0 V. When the
overdischarge detection voltage is higher than 2.6 V, the overcharge detection voltage and the
overcharge release voltage are limited as “Table 2”.
Table 2
Overdischarge
Overcharge
Voltage difference between overcharge detection
voltage and overcharge release voltage
detection voltage 1, 2 detection voltage 1, 2
VDD
VCU
VCU − VCD
1.70 to 2.60 V
1.70 to 2.80 V
1.70 to 3.00 V
3.85 to 4.60 V
3.85 to 4.60 V
3.85 to 4.50 V
0 to 0.30 V
0 to 0.20 V
0 to 0.10 V
4
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Pin Configuration
Table 3
8-Pin TSSOP
Top view
Pin No. Symbol
Description
SENS
DO
VCC
VC
1
2
4
1
SENS Detection pin for voltage between SENS and
VC (Detection for overcharge and
overdischarge)
CO
ICT
VM
VSS
2
3
4
DO
CO
VM
FET gate connection pin for discharge
control (CMOS output)
FET gate connection pin for charge control
(CMOS output)
Detection pin for voltage between VM and
VSS (Overcurrent detection pin)
Negative power input pin
Capacitor connection pin for detection delay
Middle voltage input pin
Positive power input pin
Figure 2
5
6
7
8
VSS
ICT
VC
VCC
Seiko Instruments Inc.
5
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Absolute Maximum Ratings
Table 4
(Ta = 25 °C unless otherwise specified)
Item
Symbol Applied Pin
Absolute Maximum Ratings
Unit
V
Input voltage between VCC and VSS
SENS input pin voltage
ICT input pin voltage
VDS
VSENS
VICT
VVM
VCC
SENS
ICT
V
SS − 0.3 to VSS + 18
V
V
V
SS − 0.3 to VCC + 0.3
SS − 0.3 to VCC + 0.3
V
VM input pin voltage
DO output pin voltage
CO output pin voltage
VM
V
V
CC − 18 to VCC + 0.3
VDO
DO
V
V
SS − 0.3 to VCC + 0.3
VCO
CO
V
V
VM − 0.3 to VCC + 0.3
300 (When not mounted on board) mW
Power dissipation
PD
700*1
− 40 to + 85
− 40 to + 125
mW
°C
Operating ambient temperature
Storage temperature
Topr
Tstg
°C
*1. When mounted on board
[Mounted board]
(1) Board size : 114.3 mm × 76.2 mm × t1.6 mm
(2) Name :
JEDEC STANDARD51-7
Caution The absolute maximum ratings are rated values exceeding which the product could suffer
physical damage. These values must therefore not be exceeded under any conditions.
800
700
600
500
400
300
200
100
0
100
150
50
0
°
Figure 3 Power Dissipation of Package (When Mounted on Board)
6
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Electrical Characteristics
Table 5
(Ta = 25 °C unless otherwise specified)
Test
Test
Item
[DETECTION VOLTAGE]
Overcharge detection voltage 1, 2
Symbol
VCU1, 2
Condition
Min.
Typ.
Max.
Unit
3.85 to 4.60 V,
Adjustable
VCU1, 2 VCU1, 2 VCU1, 2
0.025 0.025
VCU1, 2 VCU1, 2 VCU1, 2
1.21 1.25 1.29
VCU1, 2 VCU1, 2 VCU1, 2
1.07 1.11 1.15
VCD1, 2 VCD1, 2 VCD1, 2
0.050 0.050
VDD1, 2 VDD1, 2 VDD1 ,2
0.080 0.080
V
V
V
V
V
V
V
V
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
3
1
1
1
1
1
1
1
1
−
+
Auxiliary overcharge detection voltage 1, 2 *1
VCUaux1, 2 VCU1, 2
×
1.25
×
×
×
VCUaux1, VCUaux2
=
=
VCU1, VCU2
VCU1, VCU2
×
×
1.25 or
1.11
V
CUaux1, VCUaux2
VCUaux1, 2 VCU1, 2
×
1.11
×
×
×
3.60 to 4.60 V,
Adjustable
Overcharge release voltage 1, 2
Overdischarge detection voltage 1, 2
Overdischarge release voltage 1, 2
Overcurrent detection voltage 1
Overcurrent detection voltage 2
VCD1, 2
VDD1, 2
VDU1, 2
VIOV1
−
+
1.70 to 2.60 V,
Adjustable
−
+
1.70 to 3.80 V,
Adjustable
VDU1, 2 VDU1, 2 VDU1, 2
−
0.100
VIOV1
+
0.100
VIOV1
0.07 to 0.30 V,
Adjustable
VIOV1
−
0.020
+
0.020
Load short circuit,
VCC reference
VIOV2
−
1.57
−
1.20
−
0.83
3
Temperature coefficient 1 for detection voltage *2 TCOE1 Ta = − 40 to
+
+
85 °C
85 °C
−
0.6
0
0.6
mV/°C
Temperature coefficient 2 for detection voltage *3 TCOE2 Ta = − 40 to
−
0.24
−
0.05
0
mV/°C
[DELAY TIME (C3 = 0.22 µF) ]
Overcharge detection delay time 1, 2
Overdischarge detection delay time 1, 2
Overcurrent detection delay time 1
[INPUT VOLTAGE]
tCU1, 2 1.0 s
tDD1, 2 0.1 s
tIOV1 0.01 s
0.73
68
1.00
100
10
1.35
138
s
8, 9
8, 9
10
5
5
5
ms
ms
6.7
13.9
Absolute maximum
rating
Input voltage between VCC and VSS
VDS
−
0.3
18
16
V
V
[OPERATING VOLTAGE]
Operating voltage between VCC and VSS *4
[CURRENT CONSUMPTION]
VDSOP Output logic fixed
2.0
Current consumption during normal operation
Current consumption at power down
[OUTPUT VOLTAGE]
IOPE V1
IPDN V1
=
=
V2
V2
=
=
3.6 V
1.5 V
2.1
0
7.5
12.7
0.04
µ
A
4
4
2
2
0.0002
µA
VCC
0.05
VSS
VCC
VCC
VSS
DO voltage “H”
DO voltage “L”
CO voltage “H”
VDO(H) IOUT
VDO(L) IOUT
VCO(H) IOUT
=
10
10
10
µ
A
V
6
6
7
3
3
4
−
−
+
−
0.003
VSS
=
=
µA
V
V
0.003
VCC
+
0.05
VCC
VCC
µA
−
0.15
0.019
[CO PIN INTERNAL RESISTANCE]
Resistance between VSS and CO
[INTERNAL RESISTANCE]
RCOL VCO
−
VSS
=
9.4 V
0.29
0.6
1.44
MΩ
7
4
Resistance between VCC and VM
Resistance between VSS and VM
[0 V BATTERY CHARGE FUNCTION]
RVCM VCC
RVSM VVM
−
−
VVM
VSS
=
=
0.5 V
1.1 V
105
511
240
597
575
977
k
Ω
5
5
2
2
k
Ω
0 V battery charging
function “available”
0 V battery charging
0 V battery charge starting charger voltage
V0CHA
0.38
0.32
0.75
0.88
1.12
1.44
V
11
6
6
0 V battery charge inhibition battery voltage 1, 2 V0INH1, 2 function
V
12, 13
“unavailable”
*1. Auxiliary overcharge detection voltage is equal to the overcharge detection voltage times 1.11 for the
products without overcharge hysteresis, and times 1.25 for other products.
*2. Temperature coefficient 1 for detection voltage should be applied to overcharge detection voltage,
overcharge release voltage, overdischarge detection voltage, and overdischarge release voltage.
*3. Temperature coefficient 2 for detection voltage should be applied to overcurrent detection voltage.
*4. The DO and CO pin logic are established at the operating voltage.
Seiko Instruments Inc.
7
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Table 6
(Ta = − 20 to + 70 °C unless otherwise specified)
Test
Test
Item
[DETECTION VOLTAGE]
Overcharge detection voltage 1, 2
Symbol
VCU1, 2
Condition
Min.
Typ.
Max.
Unit
3.85 to 4.60 V,
Adjustable
VCU1, 2 VCU1, 2 VCU1, 2
0.045 0.040
VCU1, 2 VCU1, 2 VCU1, 2
1.19 1.25 1.31
VCU1, 2 VCU1, 2 VCU1, 2
1.05 1.11 1.17
VCD1, 2 VCD1, 2 VCD1, 2
0.070 0.065
VDD1, 2 VDD1, 2 VDD1 ,2
0.100 0.095
V
V
V
V
V
V
V
V
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
3
1
1
1
1
1
1
1
1
−
+
Auxiliary overcharge detection voltage 1, 2 *1
VCUaux1, 2 VCU1, 2
×
1.25
×
×
×
VCUaux1, VCUaux2
=
=
VCU1, VCU2
VCU1, VCU2
×
×
1.25 or
1.11
V
CUaux1, VCUaux2
VCUaux1, 2 VCU1, 2
×
1.11
×
×
×
3.60 to 4.60 V,
Adjustable
Overcharge release voltage 1, 2
Overdischarge detection voltage 1, 2
Overdischarge release voltage 1, 2
Overcurrent detection voltage 1
Overcurrent detection voltage 2
VCD1, 2
VDD1, 2
VDU1, 2
VIOV1
−
+
1.70 to 2.60 V,
Adjustable
−
+
1.70 to 3.80 V,
Adjustable
VDU1, 2 VDU1, 2 VDU1, 2
−
0.120
VIOV1
+
0.115
VIOV1
0.07 to 0.30 V,
Adjustable
VIOV1
−
0.029
+
0.029
Load short circuit,
VCC reference
VIOV2
−
1.66
−
1.20
−
0.74
3
Temperature coefficient 1 for detection voltage *2 TCOE1 Ta = − 40 to
+
+
85 °C
85 °C
−
0.6
0
0.6
mV/°C
Temperature coefficient 2 for detection voltage *3 TCOE2 Ta = − 40 to
−
0.24
−
0.05
0
mV/°C
[DELAY TIME (C3 = 0.22 µF) ]
Overcharge detection delay time 1, 2
Overdischarge detection delay time 1, 2
Overcurrent detection delay time 1
[INPUT VOLTAGE]
tCU1, 2 1.0 s
tDD1, 2 0.1 s
tIOV1 0.01 s
0.60
67
1.00
100
10
1.84
140
s
8, 9
8, 9
10
5
5
5
ms
ms
6.5
14.5
Absolute maximum
rating
Input voltage between VCC and VSS
VDS
−
0.3
18
16
V
V
[OPERATING VOLTAGE]
Operating voltage between VCC and VSS *4
[CURRENT CONSUMPTION]
VDSOP Output logic fixed
2.0
Current consumption during normal operation
Current consumption at power down
[OUTPUT VOLTAGE]
IOPE V1
IPDN V1
=
=
V2
V2
=
=
3.6 V
1.5 V
1.9
0
7.5
13.8
0.06
µ
A
4
4
2
2
0.0002
µA
VCC
0.14
VSS
VCC
VCC
VSS
DO voltage “H”
DO voltage “L”
CO voltage “H”
VDO(H) IOUT
VDO(L) IOUT
VCO(H) IOUT
=
10
10
10
µ
A
V
6
6
7
3
3
4
−
−
+
−
0.003
VSS
=
=
µA
V
V
0.003
VCC
+
0.14
VCC
VCC
µA
−
0.24
0.019
[CO PIN INTERNAL RESISTANCE]
Resistance between VSS and CO
[INTERNAL RESISTANCE]
RCOL VCO
−
VSS
=
9.4 V
0.24
0.6
1.96
785
MΩ
7
4
Resistance between VCC and VM
Resistance between VSS and VM
[0 V BATTERY CHARGE FUNCTION]
RVCM VCC
RVSM VVM
−
−
VVM
VSS
=
=
0.5 V
1.1 V
86
240
597
k
Ω
5
5
2
2
418
1332
1.21
1.53
kΩ
0 V battery charging
function “available”
0 V battery charging
0 V battery charge starting charger voltage
V0CHA
0.29
0.23
0.75
0.88
V
11
6
6
0 V battery charge inhibition battery voltage 1, 2 V0INH1, 2 function
V
12, 13
“unavailable”
*1. Auxiliary overcharge detection voltage is equal to the overcharge detection voltage times 1.11 for the
products without overcharge hysteresis, and times 1.25 for other products.
*2. Temperature coefficient 1 for detection voltage should be applied to overcharge detection voltage,
overcharge release voltage, overdischarge detection voltage, and overdischarge release voltage.
*3. Temperature coefficient 2 for detection voltage should be applied to overcurrent detection voltage.
*4. The DO pin and CO pin logic are established at the operating voltage.
8
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Table 7
(Ta = − 40 to +85 °C unless otherwise specified)
Test
Test
Item
Symbol
VCU1, 2
Condition
Min.
Typ.
Max.
Unit
[DETECTION VOLTAGE]
Overcharge detection voltage 1, 2
3.85 to 4.60 V,
Adjustable
VCU1, 2 VCU1, 2 VCU1, 2
0.055 0.045
VCU1, 2 VCU1, 2 VCU1, 2
1.19 1.25 1.31
VCU1, 2 VCU1, 2 VCU1, 2
1.05 1.11 1.17
VCD1, 2 VCD1, 2 VCD1, 2
0.080 0.070
VDD1, 2 VDD1, 2 VDD1 ,2
0.110 0.100
V
V
V
V
V
V
V
V
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
3
1
1
1
1
1
1
1
1
−
+
Auxiliary overcharge detection voltage 1, 2 *1
VCUaux1, 2 VCU1, 2
×
1.25
×
×
×
VCUaux1, VCUaux2
=
=
VCU1, VCU2
VCU1, VCU2
×
×
1.25 or
1.11
VCUaux1, VCUaux2
VCUaux1, 2 VCU1, 2
×
1.11
×
×
×
3.60 to 4.60 V,
Adjustable
Overcharge release voltage 1, 2
Overdischarge detection voltage 1, 2
Overdischarge release voltage 1, 2
Overcurrent detection voltage 1
Overcurrent detection voltage 2
VCD1, 2
VDD1, 2
VDU1, 2
VIOV1
−
+
1.70 to 2.60 V,
Adjustable
−
+
1.70 to 3.80 V,
Adjustable
VDU1, 2 VDU1, 2 VDU1, 2
−
0.130
VIOV1
+
0.120
VIOV1
0.07 to 0.30 V,
Adjustable
VIOV1
−
0.033
+
0.033
Load short circuit,
VCC reference
VIOV2
−
1.70
−
1.20
−
0.71
3
Temperature coefficient 1 for detection voltage *2 TCOE1 Ta = − 40 to
+
+
85 °C
85 °C
−
0.6
0
0.6
mV/°C
Temperature coefficient 2 for detection voltage *3 TCOE2 Ta = − 40 to
−
0.24
−
0.05
0
mV/°C
[DELAY TIME (C3 = 0.22 µF) ]
Overcharge detection delay time 1, 2
Overdischarge detection delay time 1, 2
Overcurrent detection delay time 1
[INPUT VOLTAGE]
tCU1, 2 1.0 s
tDD1, 2 0.1 s
tIOV1 0.01 s
0.55
67
1.00
100
10
2.06
141
s
8, 9
8, 9
10
5
5
5
ms
ms
6.3
14.7
Absolute maximum
rating
Input voltage between VCC and VSS
VDS
−
0.3
18
16
V
V
[OPERATING VOLTAGE]
Operating voltage between VCC and VSS *4
[CURRENT CONSUMPTION]
VDSOP Output logic fixed
2.0
Current consumption during normal operation
Current consumption at power down
[OUTPUT VOLTAGE]
IOPE V1
IPDN V1
=
=
V2
V2
=
=
3.6 V
1.5 V
1.8
0
7.5
14.2
0.10
µ
A
4
4
2
2
0.0002
µA
VCC
0.17
VSS
VCC
VCC
VSS
DO voltage “H”
DO voltage “L”
CO voltage “H”
VDO(H) IOUT
VDO(L) IOUT
VCO(H) IOUT
=
10
10
10
µ
A
V
6
6
7
3
3
4
−
−
+
−
0.003
VSS
=
=
µA
V
V
0.003
VCC
+
0.17
VCC
VCC
µA
−
0.27
0.019
[CO PIN INTERNAL RESISTANCE]
Resistance between VSS and CO
[INTERNAL RESISTANCE]
RCOL VCO
−
VSS
=
9.4 V
0.22
0.6
2.20
878
MΩ
7
4
Resistance between VCC and VM
Resistance between VSS and VM
[0 V BATTERY CHARGE FUNCTION]
RVCM VCC
RVSM VVM
−
−
VVM
VSS
=
=
0.5 V
1.1 V
79
240
597
k
Ω
5
5
2
2
387
1491
1.25
1.57
kΩ
0 V battery charging
function “available”
0 V battery charging
0 V battery charge starting charger voltage
V0CHA
0.26
0.20
0.75
0.88
V
11
6
6
0 V battery charge inhibition battery voltage 1, 2 V0INH1, 2 function
V
12, 13
“unavailable”
*1. Auxiliary overcharge detection voltage is equal to the overcharge detection voltage times 1.11 for the
products without overcharge hysteresis, and times 1.25 for other products.
*2. Temperature coefficient 1 for detection voltage should be applied to overcharge detection voltage,
overcharge release voltage, overdischarge detection voltage, and overdischarge release voltage.
*3. Temperature coefficient 2 for detection voltage should be applied to overcurrent detection voltage.
*4. The DO pin and CO pin logic are established at the operating voltage.
Seiko Instruments Inc.
9
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Test Circuits
(1) Test Condition 1, Test Circuit 1
Set S1 = OFF, V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Increase V1 from 3.6 V gradually.
The V1 voltage when CO = “L” is overcharge detection voltage 1 (VCU1). Decrease V1 gradually. The V1
voltage when CO = “H” is overcharge release voltage 1 (VCD1). Further decrease V1. The V1 voltage
when DO = “L” is overdischarge voltage 1 (VDD1). Increase V1 gradually. The V1 voltage when DO = “H”
is overdischarge release voltage 1 (VDU1). Set S1 = ON, and V1 = V2 = 3.6 V and V3 = 0 V under normal
condition. Increase V1 from 3.6 V gradually. The V1 voltage when CO = “L” is auxiliary overcharge
detection voltage 1 (VCUaux1).
(2) Test Condition 2, Test Circuit 1
Set S1 = OFF, V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Increase V2 from 3.6 V gradually.
The V2 voltage when CO = “L” is overcharge detection voltage 2 (VCU2). Decrease V2 gradually. The V2
voltage when CO = “H” is overcharge release voltage 2 (VCD2). Further decrease V2. The V2 voltage
when DO = “L” is overdischarge voltage 2 (VDD2). Increase V2 gradually. The V2 voltage when DO = “H”
is overdischarge release voltage 2 (VDU2). Set S1 = ON, and V1 = V2 = 3.6 V and V3 = 0 V under normal
condition. Increase V2 from 3.6 V gradually. The V2 voltage when CO = “L” is auxiliary overcharge
detection voltage 2 (VCUaux2).
(3) Test Condition 3, Test Circuit 1
Set S1 = OFF, V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Increase V3 from 0 V gradually.
The V3 voltage when DO = “L” is overcurrent detection voltage 1 (VIOV1). Set S1 = ON, V1 = V2 = 3.6 V,
V3 = 0 under normal condition. Increase V3 from 0 V gradually. (The voltage change rate < 1.0 V / ms)
V3 − (V1 + V2) voltage when DO = “L” is overcurrent detection voltage 2 (VIOV2).
(4) Test Condition 4, Test Circuit 2
Set S1 = ON, V1 = V2 = 3.6 V, and V3 = 0 V under normal condition and measure current consumption.
Current consumption I1 is the normal condition current consumption (IOPE). Set S1 = OFF, V1 = V2 =
1.5 V under overdischarge condition and measure current consumption. Current consumption I1 is the
power-down current consumption (IPDN).
(5) Test Condition 5, Test Circuit 2
Set S1 = ON, V1 = V2 = V3 = 1.5 V, and V3 = 2.5 V under overdischarge condition. (V1 + V2 − V3) / I2 is
the internal resistance between VCC and VM (RVCM).
Set S1 = ON, V1 = V2 = 3.6 V, and V3 = 1.1 V under overcurrent condition. V3 / I2 is the internal
resistance between VSS and VM (RVSM).
(6) Test Condition 6, Test Circuit 3
Set S1 = ON, S2 = OFF, V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Increase V4 from 0 V
gradually. The V4 voltage when I1 = 10 µA is DO voltage “H” (VDO(H)).
Set S1 = OFF, S2 = ON, V1 = V2 = 3.6 V, and V3 = 0.5 V under overcurrent condition. Increase V5 from
0 V gradually. The V5 voltage when I2 = 10 µA is the DO voltage “L” (VDO(L)).
10
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
(7) Test Condition 7, Test Circuit 4
Set S1 = ON, S2 = OFF, V1 = V2 = 3.6 V and V3 = 0 V under normal condition. Increase V4 from 0 V
gradually. The V4 voltage when I1 = 10 µA is the CO “H” voltage (VCO(H)).
Set S1 = OFF, S2 = ON, V1 = V2 = 4.7, V3 = 0 V, and V5 = 9.4 V under over voltage condition. (V5) / I2
is the CO pin internal resistance (RCO(L)).
(8) Test Condition 8, Test Circuit 5
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Increase V1 from (VCU1 − 0.2 V) to (VCU1
+
0.2 V) immediately (within 10 µs). The time after V1 becomes (VCU1 + 0.2 V) until CO goes “L” is the
overcharge detection delay time 1 (tCU1).
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Decrease V1 from (VDD1 + 0.2 V) to (VDD1
−
0.2 V) immediately (within 10 µs). The time after V1 becomes (VDD1 − 0.2 V) until DO goes “L” is the
overdischarge detection delay time 1 (tDD1).
(9) Test Condition 9, Test Circuit 5
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Increase V2 from (VCU2 − 0.2 V) to (VCU2
+
0.2 V) immediately (within 10 µs). The time after V2 becomes (VCU2 + 0.2 V) until CO goes “L” is the
overcharge detection delay time 2 (tCU2).
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Decrease V2 from (VDD2 + 0.2 V) to (VDD2
−
0.2 V) immediately (within 10 µs). The time after V2 becomes (VDD2 − 0.2 V) until DO goes “L” is the
overdischarge detection delay time 2 (tDD2).
(10) Test Condition 10, Test Circuit 5
Set V1 = V2 = 3.6 V, and V3 = 0 V under normal condition. Increase V3 from 0 V to 0.5 V immediately
(within 10 µs). The time after V3 becomes 0.5 V until DO goes “L” is the overcurrent detection delay time
1 (tIOV1).
(11) Test Condition 11, Test Circuit 6
Set V1 = V2 = 0 V, and V3 = 0 V, and increase V3 gradually. The V3 voltage when CO = “L” (VVM + 0.3 V
or higher) is the 0 V charge starting voltage (V0CHA).
(12) Test Condition 12, Test Circuit 6
Set V1 = 0 V, V2 = 3.6 V, and V3 = 12 V, and increase V1 gradually. The V1 voltage when CO = “H” (VVM
+ 0.3 V or higher) is the 0 V charge inhibiting voltage 1 (V0INH1).
(13) Test Condition 13, Test Circuit 6
Set V1 = 3.6 V, V2 = 0 V, and V3 = 12 V, and increase V2 gradually. The V2 voltage when CO = “H” (VVM
+ 0.3 V or higher) is the 0 V charge inhibiting voltage 2 (V0INH2).
Seiko Instruments Inc.
11
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
SENS
SENS
VCC
I1
VCC
V1
V2
S-8232 Series
S-8232 Series
V1
V2
ICT
VM
ICT
VC
S1
VC
VM
VSS
VSS
DO
CO
DO
CO
I2
V3
V3
S1
Test Circuit 1
Test Circuit 2
SENS
SENS
VCC
VCC
S-8232 Series
S-8232 Series
V1
V2
V1
V2
ICT
VM
ICT
VM
VC
VC
VSS
VSS
CO
DO
DO
CO
V3
V3
S2
S1
S2
S1
I2
I1
I2
I1
V5
V4
V5
V4
Test Circuit 3
Test Circuit 4
SENS
SENS
C3 = 0.22 µF
VCC
C3
VCC
ICT
S-8232 Series
S-8232 Series
V1
V2
V1
ICT
VM
VC
VC
V2
VM
VSS
VSS
DO
CO
DO
CO
4.7 MΩ
V3
V3
Test Circuit 5
Test Circuit 6
Figure 4
12
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Operation
Normal Condition *1, *2
This IC monitors the voltages of the two serially connected batteries and the discharge current to control
charging and discharging. When the voltages of two batteries are in the range from the overdischarge
detection voltage (VDD1, 2) to the overcharge detection voltage (VCU1, 2), and the current flowing through the
batteries becomes equal or lower than a specified value (the VM pin voltage is equal or lower than
overcurrent detection voltage 1), the charging and discharging FETs are turned on. In this condition,
charging and discharging can be carried out freely. This condition is called normal condition. In this
condition, the VM and VSS pins are shorted by the RVSM resistor.
Overcurrent Condition
When the discharging current becomes equal to or higher than a specified value (the VM pin voltage is
equal to or higher than the overcurrent detection voltage) during discharging under normal condition and
it continues for the overcurrent detection delay time (tIOV) or longer, the discharging FET is turned off to
stop discharging. This condition is called overcurrent condition. The VM and VSS pins are shorted by
the RVSM resistor at this time. The charging FET is also turned off. When the discharging FET is off and
a load is connected, the VM pin voltage equals the VCC potential.
The overcurrent condition returns to the normal condition when the load is released and the impedance
between the EB− and EB+ pins (refer to the Figure 8) is 200 MΩ or higher. When the load is released,
the VM pin, which is shorted to the VSS pin with the RVSM resistor, goes back to the VSS potential. The
IC detects that the VM pin potential returns to overcurrent detection voltage 1 (VIOV1) or lower and returns
to the normal condition.
Overcharge Condition
Following two cases are detected as overcharge conditions :
(1) If one of the battery voltages becomes higher than the overcharge detection voltage (VCU1, 2
)
during charging under normal condition and it continues for the overcharge detection delay time
(tCU1, 2) or longer, the charging FET turns off to stop charging.
(2) If one of the battery voltages becomes higher than the auxiliary overcharge detection voltage
(VCUaux1, 2) the charging FET turns off immediately to stop charging. The VM and VSS pins are
shorted by the RVSM resistor under the overcharge condition.
The auxiliary overcharge detection voltages (VCUaux1, 2) are correlated with the overcharge detection
voltages (VCU1, 2) and are defined by following equations :
VCUaux1, 2 [V] = 1.25 × VCU1, 2 [V]
or for no overcharge hysteresis type (VCU1, 2 = VCD1, 2) VCUaux1, 2 [V] = 1.11 × VCU1, 2 [V]
The overcharge condition is released in two cases :
(1) The battery voltage which exceeded the overcharge detection voltage (VCU1, 2) falls below the
overcharge release voltage (VCD1, 2), the charging FET turns on and the normal condition returns.
(2) If the battery voltage which exceeded the overcharge detection voltage (VCU1, 2) is equal or higher
than the overcharge release voltage (VCD1, 2), but the charger is removed, a load is placed, and
discharging starts, the charging FET turns on and the normal condition returns.
The release mechanism is as follows : the discharge current flows through an internal parasitic diode of
the charging FET immediately after a load is installed and discharging starts, and the VM pin voltage
increases by about 0.6 V from the VSS pin voltage momentarily. The IC detects this voltage (overcurrent
detection voltage 1 or higher), releases the overcharge condition and returns to the normal condition.
Overdischarge Condition
If any one of the battery voltages falls below the overdischarge detection voltage (VDD1, 2) during
discharging under normal condition and it continues for the overdischarge detection delay time (tDD1, 2) or
longer, the discharging FET turns off and discharging stops. This condition is called the overdischarge
condition. When the discharging FET turns off, the VM pin voltage becomes equal to the VCC voltage and
the IC’s current consumption falls below the power-down current consumption (IPDN). This condition is
called the power-down condition. The VM and VCC pins are shorted by the RVCM resistor under the
overdischarge and power-down conditions.
The power-down condition is canceled when the charger is connected and the voltage between VM and
VCC is overcurrent detection voltage 2 or higher. When all the battery voltages becomes equal to or
higher than the overdischarge release voltage (VDU1, 2) in this condition, the overdischarge condition
changes to the normal condition.
Seiko Instruments Inc.
13
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Delay Circuit
The overcharge detection delay time (tCU1, 2), the overdischarge detection delay time (tDD1, 2), and the
overcurrent detection delay time 1 (tI0V1) change with an external capacitor (C3). Since one capacitor
determine each delay time, delay times are correlated by the following ratio :
Overcharge delay time : Overdischarge delay time : Overcurrent delay time = 100 : 10 : 1
The delay times are calculated by the following equations : (Ta = − 40 to + 85 °C)
Min.,
( 2.500, 4.545, 9.364 ) × C3 [µF]
Overdischarge detection delay time tDD [s] = Delay factor ( 0.3045, 0.4545, 0.6409 ) × C3 [µF]
Overcurrent detection delay time tIOV1 [s] = Delay factor ( 0.02864,0.04545,0.06682 ) × C3 [µF]
Typ.,
Max.
Overcharge detection delay time tCU [s] = Delay factor
Remark The delay time for overcurrent detection 2 is fixed by an internal circuit. The delay time cannot
be changed via an external capacitor.
0 V Battery Charging Function *3
This function is used to recharge both of two serially-connected batteries after they self-discharge to 0 V.
When the 0 V charging start voltage (V0CHA) or higher is applied to between VM and VCC by connecting
the charger, the charging FET gate is fixed to VCC potential.
When the voltage between the gate and the source of the charging FET becomes equal to or higher than
the turn-on voltage by the charger voltage, the charging FET turns on to start charging. At this time, the
discharging FET turns off and the charging current flows through the internal parasitic diode in the
discharging FET. If all the battery voltages become equal to or higher than the overdischarge release
voltage (VDU1, 2), the normal condition returns.
0 V Battery Charge Inhibiting Function *3
This function is used for inhibiting charging when either of the connected batteries goes 0 V due to its
self-discharge. When the voltage of either of the connected batteries goes below 0 V charge inhibit
voltage 1 and 2 (V0INH1, 2), the charging FET gate is fixed to "EB−" to inhibit charging. Charging is
possible only when the voltage of both connected batteries goes 0 V charge inhibit voltage 1 and 2
(V0INH1, 2) or more.
Note that charging may be possible when the total voltage of both connected batteries is less than the
minimum value (VDSOPmin) of the operating voltage between VCC and VSS even if the voltage of either of
the connected batteries is 0 V charge inhibit voltage 1 and 2 (V0INH1, 2) or less. Charging is prohibited
when the total voltage of both connected batteries reaches the minimum value (VDSOPmin) of the operating
voltage between VCC and VSS.
When using this optional function, a resistor of 4.7 MΩ is needed between the gate and the source of the
charging control FET (refer to the Figure 8).
*1. When initially connecting batteries, the IC may fail to enter the normal condition (discharging ready
state). If so, once set the VM pin to VSS voltage (short pins VM and VSS or connect a charger).
*2. The products indicated with *4 of the 2. Product Name List in the “ Product Name Structure” are set
to “overcharge detection / release hysteresis”, “no final overcharge function”, and “0 V battery charge
inhibiting function.” The following phenomena may be found, but there is no problem for practical use.
The product is an overcurrent condition due to overload connection when the battery voltage is
overcharge release voltage (VCD1, 2) or more and overcharge detection voltage (VCU1, 2) or less. Usually,
the IC returns to its normal condition when overload is removed under this condition. However, the
charging FET may be turned OFF when overload is removed under this condition, leading to an
overcharge condition. If so, attach load to start discharge. The charging FET is turned ON to return to
the normal condition. Refer to the “Overcharge condition” in this section.
*3. Some lithium ion batteries are not recommended to be recharged after having been completely
discharged. Please contact the battery manufacturer when you decide to select a 0 V battery charging
function.
14
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Timing Charts
1. Overcharge Detection
V2 battery
V1 battery
VCUaux
VCU
Battery
VCD
VDU
VDD
voltage
VSS
VCC
DO pin
voltage
V1 auxiliary over
voltage detect
V2 auxiliary over
voltage detect
V2 over voltage detect
V1 over voltage detect
VSS
VCC
CO pin
voltage
VSS
EB−
VCC
VIOV2
VM pin
voltage VIOV1
VSS
EB−
Charger connection
Load connection
Delay time
= 0
Delay time
= 0
Delay
Delay
Mode *1
<1>
<2>
<1>
<2>
<1>
<2>
<1>
<2>
<1>
*1. <1> Normal mode
<2> Over charge mode
<3> Over discharge mode
<4> Over current mode
Remark The charger is assumed to charge with a constant current.
Figure 5
Seiko Instruments Inc.
15
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
2. Overdischarge Detection
V2 battery
V1 battery
VCU
VCD
VDU
VDD
Battery
voltage
VSS
VCC
DO pin
voltage
VSS
Vcc
CO pin
voltage
Vss
EB−
VCC
VIOV2
VIOV1
VSS
VM pin
voltage
EB−
Charger connection
Load connection
Delay
No Delay
Delay
Mode *1
<1>
<3>
<1>
<3>
<2> & <3>
<3>
*1. <1> Normal mode
<2> Over charge mode
<3> Over discharge mode
<4> Over current mode
Remark The charger is assumed to charge with a constant current.
Figure 6
16
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
3. Overcurrent Detection
V1 = V2 battery
VCU
VCD
Battery
voltage
VDU
VDD
VCC
DO pin
voltage
VSS
VCC
CO pin
voltage
VSS
EB−
VCC
VIOV2
VM pin
voltage
VIOV1
VSS
EB−
Charger connection
Load connection
delay = tIOV1
delay = tIOV2
< tIOV1
Mode *1
<1>
<4>
<1>
<4>
<1>
*1. <1> Normal mode
<2> Over charge mode
<3> Over discharge mode
<4> Over current mode
Remark The charger is assumed to charge with a constant current.
Figure 7
Seiko Instruments Inc.
17
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Battery Protection IC Connection Example
EB+
R4
1 kΩ
SENS
R1
1 kΩ
VCC
Battery 1
C1
C2
0.22 µF
R2
1 kΩ
S-8232 Series
VC
Battery 2
0.22 µF
Delay time setting
ICT
VM
VSS
DO
CO
C3
0.22 µF
R3
1 kΩ
R5
4.7 MΩ
FET1
FET2
EB−
Figure 8
Table 8 Constants for External Components
Symbol
FET1
FET2
R1
Parts
Purpose
Typ.
1 kΩ
0.22 µF
1 kΩ
0.22 µF
1 kΩ
Min.
300 Ω
0 µF
300 Ω
0 µF
Max.
1 kΩ
1 µF
1 kΩ
1 µF
Remark
Nch MOS FET Discharge control
Nch MOS FET Charge control
Chip resistor
ESD protection
C1
Chip capacitor Filter
R2
Chip resistor
ESD protection
C2
Chip capacitor Filter
R4
Chip resistor
ESD protection
= R1 min. = R1 max. Same value as R1 and R2. *1
Attention should be paid to leak
C3
Chip capacitor Delay time setting
0.22 µF
0 µF
1 µF
current of C3. *2
Protection for
charger reverse
connection
Discharge can’t be stopped at less
than 300 Ω when a charger is
reverse-connected. *3
R3
Chip resistor
Chip resistor
1 kΩ
300 Ω
5 kΩ
R5 should be added when the
product has 0 V battery charge
inhibition. Lower resistance
increases current consumption. *4
0 V battery
charging inhibition
R5
(4.7 MΩ)
(1 MΩ)
(10 MΩ)
*1. R4
= R1 is required. Overcharge detection voltage increases by R4. For example 10 kΩ (R4) increases overcharge
detection voltage by 20 mV.
*2. The overcharge detection delay time (tCU), the overdischarge detection delay time (tCD), and the over current detection
delay time (tIOV) change with the external capacitor C3. Refer to the “ Electrical Characteristics”.
*3. When the resistor R3 is set less than 300
Ω and a charger is reverse-connected, current which exceeds the power
dissipation of the package will flow and the IC may break. But excessive R3 causes increase of overcurrent detection
voltage 1 (VIOV1). VIOV1 changes to VIOV1 = (R3 + RVSM) / RVSM × VIOV1. For example, 50 k
overcurrent detection voltage 1 (VIOV1) from 0.100 V to 0.113 V.
Ω resistor (R3) increases
*4. A 4.7 M
Ω resistor is needed for R5 to inhibit 0 V battery charging. Current consumption increases when the R5
resistance is below 4.7 MΩ. R5 should be connected when the product has 0 V battery charging inhibition.
Caution 1. The above constants may be changed without notice.
2. It has not been confirmed whether the operation is normal or not in circuits other than the above
example of connection. In addition, the example of connection shown above and the constant do not
guarantee proper operation. Perform through evaluation using the actual application to set the
constant.
18
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Precautions
• After the overcurrent detection delay, if either one of battery voltages equals the overdischarge detection
voltage (VDD1,2) or lower, the overdischarge detection delay time becomes shorter than 10ms (min.). It
occurs because capacitor C3 sets all of delay times (refer to the Figure 9) .
The battery voltage is equal to
or less the overdischarge voltage (VDD
)
after stopping the overcurrent.
VDD
Battery
voltage
0 V
VCC
VSS
DO pin
voltage
VCC
VIOV2
VIOV1
VSS
VM pin
voltage
EB−
The over current delay
Load connect
The delay time becomes shorter than typical
The over discharge delay
Figure 9
[Cause]
When overcurrent detection is released until tIOV1, the capacitor C3 is charged by S-8232 Series. If all
battery voltage is lower than VDD1, 2 at that time, charging goes on. So delay time is shorter than
typical.
[Conclusion]
This phenomenon occurs when all battery voltage is nearly equal to the overdischarge voltage (VDD1, 2
)
after overcurrent detected. It means that the battery capacity is small and those must be charged in
the future. Even if the state changes to overdischarge condition, the battery package capacity is same
as typical.
• When one of the battery voltages is overdischarge detection voltage (VDD1, 2) or lower and the other one
becomes higher than the overcharge detection voltage (VCU1, 2), the IC detects the overcharge without the
overcharge detection delay time (tCU) (refer to the Figure 10) .
VCU
Battery
oltage
VCD
VDU
VDD
v
Overdischarge state
Overcharge detect
V
1
VCU
VCD
Battery
oltage
v
VDU
VDD
V
2
VCC
CO pin
oltage
v
VSS
EB−
Delay time = 0
Charger connected
Figure 10
[Cause]
It is same as the overdischarge detection under the overcurrent condition. It occurs because capacitor
C3 sets all of delay times.
[Conclusion]
This phenomenon occurs when one battery voltage is lower than overdischarge voltage (VDD1, 2) and
batteries are charged by charger. Since voltage difference between two batteries is large in this
situation, the S-8232 Series immediately stops the charging of the other battery to reduce voltage
difference. This action improves the safety of a battery pack and dose not do any harm to the pack.
Seiko Instruments Inc.
19
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
• After the overcurrent detection, the load was connected for a long time, even if one of the battery voltage
became lower than overdischarge detection voltage (VDD1, 2), the IC can’t detects the overdischarge as
long as the load is connected. Therefore the IC’s current consumption at the one of the battery voltage is
lower than the overdischarge detection voltage is same as normal condition current consumption (IOPE
)
(refer to the Figure 11).
The battery voltage is less than the overdischarge
detection voltage, by self current consumption
Battery
voltage
VDD
0 V
As long as the load is connected, the IC’s current is
same as normal current consumption (IOPE
)
IOPE
Current
consumption
IPDN
0 A
VCC
VSS
DO pin
voltage
VCC
VIOV2
VIOV1
VSS
VM pin
voltage
EB−
Load connect
The over current delay
Long haul load connected
Figure 11
[Cause]
The reason is as follows. If the overcurrent detection and overdischarge detection occur at same time,
the overcurrent detection takes precedence the overdischarge detection. As long as the IC detects
overcurrent, the IC can’t detect overdischarge.
[Conclusion]
If the load is taken off at least one time, the overcurrent is released and the overdischarge detection
works.
Unless keeping the IC with load for a long time, the reduction of battery voltage will be neglected,
because of the IC’s current consumption (typ. 7.5 µA) is small.
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in
electrostatic protection circuit.
• SII claims no responsibility for any and all disputes arising out of or in connection with any infringement
of the products including this IC upon patents owned by a third party.
20
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Typical Characteristics
1. Detection Voltage Temperature Characteristics
Overcharge detection voltage1 vs. temperature
Overcharge detection voltage2 vs. temperature
VCU2 = 4.30 [V]
VCU1 = 4.30 [V]
4.4
4.3
4.2
4.4
4.3
4.2
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [°C]
Ta [°C]
Overcharge release voltage1 vs. temperature
Overcharge release voltage2 vs. temperature
VCD1 = 4.00 [V]
VCD2 = 4.00 [V]
4.1
4
4.1
4
3.9
-40
3.9
-40
-20
0
20
40
60
80
100
-20
0
20
40
60
80
100
Ta [°C]
Ta [°C]
Auxiliary overcharge detection voltage1 vs. temperature
Auxiliary overcharge detection voltage2 vs. temperature
VCUaux1 = 5.375 [V]
VCUaux2 = 5.375 [V]
5.45
5.35
5.25
5.45
5.35
5.25
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [°C]
Ta [°C]
Seiko Instruments Inc.
21
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
Overdischarge detection voltage1 vs. temperature
Overdischarge detection voltage2 vs. temperature
V
DD1 = 2.00 [V]
VDD2 = 2.00 [V]
2.1
2.1
2
2
1.9
1.9
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [°C]
Ta [°C]
Overdischarge release voltage1 vs. temperature
Overdischarge release voltage1 vs. temperature
V
DU1 = 2.60 [V]
VDU2 = 2.60 [V]
2.7
2.6
2.5
2.7
2.6
2.5
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [°C]
Ta [°C]
Overcurrent1 detection voltage vs. temperature
Overcurrent1 detection voltage vs. temperature
VIOV2 = 1.20 [V] (VCC reference)
VIOV1 = 0.1 [V]
-1.10
-1.15
-1.20
-1.25
-1.30
0.12
0.10
0.08
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [°C]
Ta
22
Seiko Instruments Inc.
BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK
S-8232 Series
Rev.5.4_00
2. Current Consumption Temperature Characteristics
Current consumption vs. temperature in normal mode
Current consumption vs. temperature in power-down mode
VCC = 7.2 [V]
V
CC = 3.0 [V]
15
10
5
100
50
0
0
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [°C]
Ta [°C]
3. Delay Time Temperature Characteristics
Overcharge detection1 time vs. temperature
Overcharge detection1 time vs. temperature
C3 = 0.22 [µF]
C3 = µ
1.5
150
1
100
50
0.5
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [°C]
Ta [°C]
Overcurrent1 detection time vs. temperature
C3 = 0.22 [µF]
12
11
10
9
8
7
-40
-20
0
20
40
60
80
100
Ta [°C]
Seiko Instruments Inc.
23
+0.3
-0.2
3.00
5
8
1
4
0.17±0.05
0.2±0.1
0.65
No. FT008-A-P-SD-1.1
TSSOP8-E-PKG Dimensions
FT008-A-P-SD-1.1
TITLE
No.
SCALE
UNIT
mm
Seiko Instruments Inc.
4.0±0.1
2.0±0.05
ø1.55±0.05
0.3±0.05
+0.1
-0.05
8.0±0.1
ø1.55
(4.4)
+0.4
-0.2
6.6
8
1
4
5
Feed direction
No. FT008-E-C-SD-1.0
TITLE
TSSOP8-E-Carrier Tape
FT008-E-C-SD-1.0
No.
SCALE
UNIT
mm
Seiko Instruments Inc.
13.4±1.0
17.5±1.0
Enlarged drawing in the central part
ø21±0.8
2±0.5
ø13±0.5
No. FT008-E-R-SD-1.0
TSSOP8-E-Reel
FT008-E-R-SD-1.0
TITLE
No.
SCALE
UNIT
QTY.
3,000
mm
Seiko Instruments Inc.
·
·
The information described herein is subject to change without notice.
Seiko Instruments Inc. is not responsible for any problems caused by circuits or diagrams described herein
whose related industrial properties, patents, or other rights belong to third parties. The application circuit
examples explain typical applications of the products, and do not guarantee the success of any specific
mass-production design.
·
·
·
When the products described herein are regulated products subject to the Wassenaar Arrangement or other
agreements, they may not be exported without authorization from the appropriate governmental authority.
Use of the information described herein for other purposes and/or reproduction or copying without the
express permission of Seiko Instruments Inc. is strictly prohibited.
The products described herein cannot be used as part of any device or equipment affecting the human
body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus
installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc.
Although Seiko Instruments Inc. exerts the greatest possible effort to ensure high quality and reliability, the
failure or malfunction of semiconductor products may occur. The user of these products should therefore
give thorough consideration to safety design, including redundancy, fire-prevention measures, and
malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.
·
S-8232NNFT-T2-G 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
S-8232NOFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8232NPFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8232NQFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8232NRFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8232NSFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8232NTFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8232NUFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8232NWFT-T2-G | SII | BATTERY PROTECTION IC FOR 2-SERIAL-CELL PACK | 获取价格 | |
S-8233A | SII | BATTERY PROTECTION IC FOR 3-SERIAL-CELL PACK | 获取价格 | |
S-8233ACFE-TB | SII | BATTERY PROTECTION IC FOR 3-SERIAL-CELL PACK | 获取价格 |
S-8232NNFT-T2-G 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 8
- 2024-09-20
- 8
- 2024-09-20
- 6